Next | Top | Index
Full Table of Contents
- Contents
-
- IRIX Admin Manual Set
-
- About This Guide
-
- What This Guide Contains
-
- Conventions Used in This Guide
-
- Additional Resources
-
- 1. - Terminals and Modems
-
- About the TTY Subsystem
-
- Terms
-
- Installing an ASCII Terminal
-
- Connecting the Terminal Hardware
-
- Configuring the Terminal Software
-
- Setting Terminal Options
-
- Installing a Modem
-
- Before You Begin
-
- Connecting the Modem Hardware
-
- Setting Up the Modem Software
-
- Modem Software Setup, All Modes
-
- Dial-out Mode
-
- Dial-in Mode
-
- Dialing Out to Another Modem
-
- Managing the TTY Subsystem
-
- Checking Line Settings Using IRIX Shell Commands
-
- Creating and Testing Line Settings
-
- Modifying Line Characteristics
-
- Serial Port Pin Signal Tables
-
- Defining the Serial Interface
-
- Cabling the Serial Ports
-
- DB-9 Serial Connector Cabling
-
- Mini-DIN8 Serial Connector Cabling
-
- 2. - Printers
-
- Understanding the lp Spooler
-
- Terms
-
- Command Interface to lp
-
- User Command Summary
-
- lp: Send a Print Job to a Printer
-
- cancel: Remove a Print Request
-
- disable: Stop Printer From Processing Requests
-
- enable: Allow Printer to Process Requests
-
- lpstat: Report lp Status
-
- Administrator Command Summary
-
- lpsched: Start the lp Scheduler
-
- lpshut: Stop the lp Scheduler
-
- reject: Prevent Print Requests
-
- accept: Allow Print Requests
-
- lpmove: Move a Request to Another Printer
-
- lpadmin: Configure Printers
-
- Managing the lp System
-
- Adding a Printer
-
- Adding Parallel and Serial Printers
-
- Adding a SCSI Printer
-
- Adding a Network Print Server
-
- Removing a Printer
-
- Changing the Default Printer Destination
-
- Managing Printing on Print Server Systems
-
- Checking Print Server Status
-
- Canceling Print Server Requests
-
- Configuring the BSD lpr Spooler System
-
- Verifying Installation of the BSD lpr Subsystem
-
- Configuring the Printcap File
-
- Printcap Examples
-
- Using the lpr Command to Print
-
- Printer Cable Pin Signal Tables
-
- Parallel Port Pin Signal Table
-
- Serial Port Pin Signal Tables
-
- DB-9 Connector Cabling
-
- Mini-DIN8 Connector Cabling
-
- 3. - CD-ROM, Floptical, and Floppy Disk Drives
-
- Floppy Disk and CD-ROM Filesystems
-
- CD-ROM Filesystems
-
- Floppy Disk Filesystems
-
- Configuring Floppy Disk Drive Device Files
-
- Using Floppy Disk Drives
-
- Using DOS and Macintosh Floppy Disks
-
- Using a Floppy Disk Drive for IRIX File Transfer
-
- Floppy Disk File Transfer With tar
-
- Floppy Disk File Transfer With cpio
-
- Floppy Disk File Transfer With dd
-
- 4. - Tape Drives
-
- Adding a Tape Drive
-
- MAKEDEV Commands for Tape Drives
-
- Tape Capacities
-
- Making Tape Drive Links
-
- 1/2-Inch Tape Drives
-
- Switch Settings for the Kennedy 1/2-Inch SCSI Tape Drive
-
- 8mm and 4mm Tape Drives
-
- Exabyte 8mm Cartridge Tape Media Specifications
-
- QIC Tape Drives
-
- Using dump With DAT Tapes
-
- Tape Drive Cleaning Process
-
- 1/2-Inch Reel-to-Reel Cipher Tape Drive Cleaning Process
-
- 1/2-Inch Reel-to-Reel Kennedy Tape Drive Cleaning Process
-
- 8mm and 4mm Tape Drive Cleaning Process
-
- 5. - Troubleshooting
-
- Troubleshooting Your Modem Setup
-
- Troubleshooting Your Printing System
-
- Hardware Troubleshooting Checklist
-
- Software Troubleshooting Checklist
-
- Troubleshooting Network Printers
-
- Emergency Measures
-
- Troubleshooting the BSD lpr Spooling System
-
- Troubleshooting Inaccessible Tape Drives
-
- Checking the Hardware
-
- Checking the Software
-
- Troubleshooting Tape Read Errors
-
- A. - Error Messages
-
- lp Error Messages
-
- Tape Drive Error Indications
-
- B. - Peripheral Device Files
-
- Index
-
Next | Top | Index