home *** CD-ROM | disk | FTP | other *** search
/ The World of Computer Software / World_Of_Computer_Software-02-385-Vol-1of3.iso / i / ide_dos.zip / IDE_DOS.EXE / INSTALL.HLP (.txt) < prev    next >
Help Librarian Help File  |  1992-04-14  |  43KB  |  725 lines

  1. C-Worthy (R) Help Librarian Data File Version 1.0
  2. COPYRIGHT (C) 1985 - 1989.  All Rights Reserved.
  3. Custom Design Systems, Inc.  Orem, Utah  USA.
  4.                          HELP - Verify Configuration
  5.                         
  6.   The Install program is displaying a list of the hard disks that it has
  7.   determined are present in your system.  If this list appears to be
  8.   wrong, it may be due to one of the following reasons:
  9.     * if a drive-type has already been specified in CMOS, the drive size
  10.       in this list will match that reported by CMOS, not the drive's
  11.       true size
  12.     * the drive's data or power cables may be loose
  13.     * some disks, such as RAM disks and network drives, will not appear
  14.       in the list, though they will still operate in your system
  15.     * only the first 8 hard disks will be displayed
  16.   Press <Enter> to confirm that the list is correct or press <F10> to
  17.   exit the program now to correct any hardware errors before proceeding.
  18.                                <Esc> Cancel
  19.                            HELP - Select Mode
  20.                            
  21.   Manual installation lets you set the number and sizes of partitions on
  22.   your hard disk.  In Manual mode, you can also delete and reformat
  23.   existing partitions.
  24.   Automatic Installation partitions and formats each unformatted disk to
  25.   the maximum size allowed by the operating system or the hard disk.  It
  26.   does not change partially or completely formatted disks.
  27.   Options lets you configure several disk formatting options.
  28.   Colors cycles between the 3 color palettes and 1 monochrome palette./
  29.                           HELP - Select Option
  30.                           
  31.   Create Primary Partition On Second Hard Disk:  "No" specifies only the
  32.   first hard disk in the system will be installed as bootable.  "Yes"
  33.   specifies that the Install program should make every disk it installs
  34.   bootable by DOS.  This will sometimes effect the way drive leters are
  35.   assigned to your physical hard disks.
  36.   Use DOS Read-Verify Type Format:  "No" causes the Install program to
  37.   use an accelerated format method to format the hard disk (supported
  38.   only by Quantum IDE hard disks).  "Yes" specifies that the Install
  39.   program should read-verify the entire hard disk before initializing
  40.   it.  This procedure takes some time and is not necessary on error-free
  41.   disks.
  42.   <PgDn>                                                      Page 1 of 2
  43.                           HELP - Select Option
  44.                           
  45.   Use Extended BIOS Table When Setting CMOS:  "No" specifies that the
  46.   Install program should use only the standard BIOS drive-types when
  47.   trying to find the closest match for your hard disk.  "Yes" specifies
  48.   that Install should also try to find extended drive-types in your
  49.   computer's BIOS.  
  50.   Use Software Driver For Full Capacity:  "No" specifies that the
  51.   Install program will not use the DOS device driver IDE_DOS.SYS.  The
  52.   amount of your hard disk that is available for use will be determined
  53.   by how closely a match for your disk can be found in the computer's
  54.   BIOS.  "Yes" specifies that the device driver should be used, which
  55.   will allow all the hard disk space to be used by DOS, regardless of
  56.   what BIOS drive-types are available.
  57.                                <Esc> Cancel                  Page 2 of 2
  58.                       HELP - No Unpartitioned Drives
  59.                       
  60.   All of the hard disks in your system have been partitioned, and
  61.   Automatic mode will not change partitioned disks.  To make any changes
  62.   to your system configuration, you will need to use Manual mode.
  63.   Hard disks that are only partially partitioned cannot be changed using
  64.   the Automatic mode.  You must use Manual mode to make any changes to
  65.   these hard disks.
  66.                           HELP - Select Disk
  67.                           
  68.   The up (
  69. ) and down (
  70. ) arrow keys move the highlight bar to each of
  71.   the recognized hard disks in the system.  Once the hard disk you want
  72.   to work on is highlighted, press the <Enter> key to proceed.  If your
  73.   system contains drives other than Quantum IDE drives, they will also
  74.   appear in this list but they will not be selectable.
  75.   In addition, selecting Options lets you configure several disk
  76.   formatting options.
  77.                      HELP - Disk Already Partitioned
  78.                      
  79.   If you continue from this point, and you make any changes to existing
  80.   partitions, you will lose data that is already on the disk.
  81.   You may continue and modify unpartitioned space on the disk without
  82.   losing data.
  83.      To continue working on this hard disk, press <Enter>.
  84.      To select another hard disk, press <Esc>.
  85.                         HELP - Enter Volume Size
  86.                         
  87.   Enter the size of the volume (partition) you wish to create in
  88.   millions of bytes (where 1 MB = 1,000,000 bytes).  Then press <Enter>.
  89.   The volume will then be created.  Formatting of the volume will occur
  90.   when you select the Commit Changes menu option on the Partition and
  91.   Format menu.
  92.                         HELP - Enter Volume Label
  93.                         
  94.   You can type in a volume label (up to 11 characters) or leave the
  95.   label blank.
  96.   Press <Enter> to enter the label and continue to the next volume.
  97.                         HELP - No Free Space Available
  98.                         
  99.   There is no available space on the hard disk to create a new volume.
  100.   If you wish to make changes to this disk, you must first delete one or
  101.   more of the existing volumes (which will result in lost data if any
  102.   exists in the deleted volume or volumes).
  103.   To create volumes on another hard disk, press <Enter> to return to the
  104.   Hard Disk Configuration menu.  From there, you can either save these
  105.   changes (using the Save Changes menu option), then press <Esc> to
  106.   return to the Select Hard Disk menu, or discard these changes using
  107.   the Cancel Changes menu option.
  108.                           HELP - Abort Formatting
  109.                           
  110.   You can abort the formatting of this volume.  If you do, the volume
  111.   will not be available for your use after the install is complete.
  112.       To abort the formatting, select <Yes>.
  113.       To continue the formatting, select <No>.
  114.                           HELP - Volume Created
  115.                           
  116.   Your volume was successfully created.  Press <Enter> to return to the
  117.   Create Volume menu and add additional volumes if unpartitioned space
  118.   on the hard disk remains.
  119.                                  HELP - Exit
  120.                                  
  121.   To program will now reboot your system to ensure that the changes you
  122.   have made are recognized.
  123.   To continue with the exit procedure, press <Ctrl><Alt><Del>.
  124.                         HELP - Insert System Disk
  125.                         
  126.   The disk in drive A: is not the correct disk.  You must insert the
  127.   system (boot) disk from which you originally booted the system (or a
  128.   disk with the exact same version of the operating system).
  129.   If you do not insert the proper disk, you will not be able to continue
  130.   with the installation.
  131.                    HELP - Extended Partition Warning
  132.                    
  133.   You have an extended partition defined on the hard disk and your
  134.   version of DOS does not support extended partitions.  Your version of
  135.   DOS only supports up to 32 MB on the hard disk.
  136.   To access volumes in the extended partition you must use the Quantum
  137.   IDE DOS device driver (IDE_DOS.SYS).  Press <Enter> to continue and
  138.   use the up (
  139. ) and down (
  140. ) arrow keys to select the CMOS
  141.   Configuration option.
  142.   Select the Software Driver option in the Set CMOS Configuration menu
  143.   and continue with the installation.
  144.                             HELP - Create Volume
  145.                             
  146.   You have used all of the possible volume IDs (C: through Z:).  There
  147.   are no IDs available to create any new volumes.
  148.   If you wish to continue working on this hard disk, you can either view
  149.   or delete these volumes, or save the changes you have made.
  150.   To select another hard disk, press <Enter> to return to the Hard Disk
  151.   Configuration menu.  From there, you can either save these changes
  152.   (using the Save Changes menu option), then press <Esc> to return to
  153.   the Select Hard Disk menu, or discard these changes using the Cancel
  154.   Changes menu option.
  155.                   HELP - No Free Partition Entry Available
  156.                   
  157.   You have three or more non-DOS partitions on this hard disk, and there
  158.   is not room to create another partition.
  159.   If you want to create additional DOS partitions on this hard disk, you
  160.   must delete at least one of the non-DOS partitions.  You can use the
  161.   Delete Volume menu option on the Hard Disk Configuration menu (in
  162.   Manual Mode) to delete the partition.
  163.                            HELP - Delete Volume
  164.                            
  165.   The up (
  166. ) and down (
  167. ) arrow keys move the highlight bar to each of
  168.   the volumes on the disk.  Once you highlight the volume you want to
  169.   delete, press the <Enter> key to proceed.
  170.                     HELP - Volume Already Deleted
  171.                     
  172.   The volume you selected is already deleted.  Press <Enter> to select
  173.   another volume.
  174.                      HELP - Delete Volume Verification
  175.                      
  176.   The volume you have selected may contain data.  If you delete this
  177.   volume, any data it contains will be lost.
  178.      If you wish to delete the volume, press <Enter>.
  179.      If you do not wish to delete the volume, Press <Esc>.
  180.                           HELP - Volume Deleted
  181.                           
  182.   The volume you selected has been deleted.  After you press <Enter>,
  183.   you can select another volume to delete, or return to the Partition
  184.   and Format menu.
  185.   Press <Enter> to continue.
  186.                           HELP - View Volumes
  187.                           
  188.   The bottom window displays formatted volumes and unused space on your
  189.   hard disk.  The columns provide you with the following information:
  190.   Volume:  The letter that refers to the volume when you are using the
  191.     system.  This may differ from the letter you actually use if there
  192.     are unrecognized hard disks or RAM disks installed in your system.
  193.   Size:  The size in MB (1 MB = 1,000,000 bytes) of the volume or space.
  194.   Operating System:  The operating system with which the disk was
  195.     created.
  196.   Volume Label:  The label for the volume.
  197.                                  HELP - Exit
  198.                                  
  199.   To return to your previous location in the program, move the highlight
  200.   bar to <No>, then press <Enter>.
  201.   To continue with the exit procedure, use the up (
  202. ) and down (
  203. ) arrow
  204.   keys to move the highlight bar to <Yes> and press <Enter>.  The exit
  205.   procedure updates your system configuration with any changes you have
  206.   made.
  207.                             HELP  - Delete Volume
  208.                             
  209.   The area you selected is not a volume.  It represents non-partitioned,
  210.   non-formatted space on your hard disk.  There is no need to delete it.
  211.   You can create a volume in this space by using the Create Volumes menu
  212.   option in the Volume Configuration menu.
  213.                            HELP - Create Volumes
  214.                            
  215.   You can create, delete, or view the volumes (partitions) on the hard
  216.   disk you have selected.
  217.   Create Volumes lets you create and name volumes of any size up to the
  218.   maximum allowed by the operating system or the hard disk.  To create a
  219.   volume, you must have blank (unformatted) space on the hard disk you
  220.   have selected.  You can verify that you have blank space by first
  221.   selecting View Volumes; blank areas will contain the phrase '<Blank>'
  222.   or '<Unused Space>' under the Operating System column.
  223.   A volume must be created in a contiguous space on the hard disk, so
  224.   if you have two unformatted spaces with a formatted area between them,
  225.   you cannot create a volume that is as large as the sum of the two
  226.   spaces.
  227.                             HELP - Delete Volume
  228.                             
  229.   There are no volumes on this hard disk to delete.
  230.   On the hard disk you've selected, you can create new volumes, or you
  231.   can select another hard disk to work on.
  232.   To select another hard disk, press <Enter> to return to the Select
  233.   Hard Disk menu. From there, you can either save these changes (using
  234.   the Save Changes menu option), then press <Esc> to return to the
  235.   Select Hard Disk menu, or discard these changes using the Cancel
  236.   Changes menu option.
  237.                            HELP - Create Volume
  238.                            
  239.   You have partitioned all of the space on this hard disk.  There is no
  240.   room to create any new volumes.
  241.   If you wish to continue working on this hard disk, you can either view
  242.   or delete these volumes, or save the changes you have made.
  243.   To select another hard disk, press <Enter> to return to the Hard Disk
  244.   Configuration menu.  From there, you can either save these changes
  245.   (using the Save Changes menu option), then press <Esc> to return to the
  246.   Select Hard Disk menu, or discard these changes using the Cancel
  247.   Changes menu option.
  248.                             HELP - Create Volume
  249.                             
  250.   You have entered a volume size that exceeds the available unused space
  251.   in this area of the hard disk, or the maximum volume size allowed by
  252.   your operating system.
  253.   You can either enter a smaller number in the Size column, or if you
  254.   would prefer to have the Install program select the maximum possible
  255.   size, press <Enter> and the Install program will fill in the maximum
  256.   allowable volume size.
  257.                       HELP - No Volume IDs Available
  258.                       
  259.   There are no more Volume IDs available for creating volumes (C:
  260.   through Z: have been allocated).  If you wish to create additional
  261.   volumes, you must delete or combine existing volumes.  To do so, use
  262.   the Delete Volume and Create Volume options in the Volume
  263.   Configuration menu in Manual mode to alter your hard disk
  264.   configurations.
  265.                            HELP - Delete Volumes
  266.                            
  267.   You can create, delete, or view the volumes (partitions) on the hard
  268.   disk you have selected.
  269.   Delete Volumes removes volumes from the disk, making them no longer
  270.   recognizable by the operating system.  To create a single large volume
  271.   from multiple smaller volumes, the smaller volumes must be deleted
  272.   before the larger volume is created (note: volumes may only be created
  273.   from contiguous spaces on the disk).  Any data contained in a deleted
  274.   volume will no longer be readable.
  275.                             HELP - View Volumes
  276.                             
  277.   You can create, delete, or view the volumes (partitions) on the hard
  278.   disk you have selected.
  279.   View Volumes starts by displaying the configuration of the selected
  280.   disk.  As you make changes, it displays the configuration as if all
  281.   modifications had been committed (note that the changes you make to
  282.   your hard disk are not actually made until you commit them).
  283.   To discard the changes and start over on the same disk, press <Esc>
  284.   twice to display the Hard Disk Configuration menu, choose the Cancel
  285.   Changes menu option to discard the changes, respond that you wish to
  286.   continue, and then select the same disk.
  287.                             HELP - Save Changes
  288.                             
  289.   You can set or change the BIOS drive-type, and create, delete, or view
  290.   the volumes (partitions) on the hard disk you have selected.
  291.   The hard disk is not actually modified until you save your changes, at
  292.   which time the disk is re-partitioned and formatted.  Until you have
  293.   saved your changes, your disk has not been physically changed and you
  294.   can discard the changes (and keep your original configuration and
  295.   data) by selecting another hard disk, or by exiting the program.
  296.                            HELP - Cannot Read File
  297.                            
  298.   The Install program cannot read the file specified in the error
  299.   message.
  300.   Please check that the file exists.
  301.   If it does, check to make sure all cables are connected and that the
  302.   power to the hard disk is on.
  303.   If the file is on C: and you have not partitioned hard disk #1, you
  304.   must exit the Install program, re-start it, and create a volume C: on
  305.   hard disk #1.
  306.                         HELP - Cannot Read Partition
  307.                         
  308.   The Install program cannot read the partition table on this hard disk.
  309.   Please make sure all cables are connected and that the power to the
  310.   hard disk is on.
  311.   If all cables are connected and the power is on, you should back up
  312.   the data on the hard disk (if any exists), re-start the Install
  313.   program, delete and re-create all volumes on the hard disk (using
  314.   Manual Mode), and then restore your data.
  315.   If the problem persists, you might have a defective hard disk.
  316.   Contact your local dealer or Quantum Corporation.
  317.                           HELP - Cannot Write Partition
  318.                           
  319.   The Install program cannot write to the partition.
  320.   Please make sure all cables are connected and the power to the hard
  321.   disk is on.
  322.   If all cables are connected and the power is on, delete the volume you
  323.   created and re-create it.
  324.   If the problem persists, you might have a defective disk.
  325.   Contact your local dealer or Quantum Corporation.
  326.                          HELP - Cannot Read Boot Block
  327.                          
  328.   The Install program cannot read the boot block on your hard disk.
  329.   Please make sure all cables are connected and that the power to the
  330.   hard disk is on.
  331.   If all cables are connected and the power is on, you should back up
  332.   the data on this volume (if any exists), re-start the Install program,
  333.   delete and re-create the volume on the hard disk (using Manual Mode),
  334.   and then restore your data.
  335.   If the problem persists, you might have a defective hard disk.
  336.   Contact your local dealer or Quantum Corporation.
  337.                        HELP - Cannot Write Boot Block
  338.                        
  339.   The Install program cannot write the boot block for this volume.
  340.   Please make sure all cables are connected and the power to the hard
  341.   disk is on.
  342.   If all cables are connected and the power is on, delete the volume you
  343.   created and re-create it.
  344.   If the problem persists, you might have a defective hard disk.
  345.   Contact your local dealer or Quantum Corporation.
  346.                        HELP - Cannot Write FAT Table
  347.                        
  348.   The Install program cannot write the FAT Table for your hard disk.
  349.   Please make sure all cables are connected and the power to the hard
  350.   disk is on.
  351.   If all cables are connected and the power is on, delete the volume you
  352.   created and re-create it.
  353.   If the problem persists, you might have a defective hard disk.
  354.   Contact your local dealer or Quantum Corporation.
  355.                       HELP - Cannot Read Root Directory
  356.                       
  357.   The Install program cannot read the root directory on this volume.
  358.   Please make sure all cables are connected and that the power to the
  359.   hard disk is on.
  360.   If all cables are connected and the power is on, you should back up
  361.   the data on this volume (if any exists), re-start the Install
  362.   program, delete and re-create this volume on the hard disk (using
  363.   Manual Mode), and then restore your data.
  364.   If the problem persists, you might have a defective hard disk.
  365.   Contact your local dealer or Quantum Corporation.
  366.                       HELP - Cannot Write Root Directory
  367.                       
  368.   The Install program cannot write the root directory on your hard disk.
  369.   Please make sure all cables are connected and the power to the hard
  370.   disk is on.
  371.   If all cables are connected and the power is on, delete the volume you
  372.   created and re-create it.
  373.   If the problem persists, you might have a defective hard disk.
  374.   Contact your local dealer or Quantum Corporation.
  375.                        HELP - Cannot Write Volume Label
  376.                        
  377.   The Install program cannot write the volume label on your hard disk.
  378.   Please make sure all cables are connected and the power to the hard
  379.   disk is on.
  380.   If all cables are connected and the power is on, delete the volume you
  381.   created and re-create it.
  382.   If the problem persists, you might have a defective hard disk.
  383.   Contact your local dealer or Quantum Corporation.
  384.                          HELP - No Supported Drives
  385.                          
  386.   There are no drives in your system supported by this Install program.
  387.   If this differs from your expectations, it may be due to one of the
  388.   following reasons:
  389.        * No Quantum IDE drives are present
  390.        * your adapter card is not configured appropriately
  391.        * the power cables may be loose
  392.        * the data cables may be loose
  393.   Exit the Install program and check your adapter configuration, system
  394.   configuration, and cabling.
  395.                      HELP - First Hard Disk not Bootable
  396.                      
  397.   Your first hard disk (#1) is not bootable by DOS.  If this differs
  398.   from your expectations, it may be due to one of the following reasons:
  399.     * you do not have a valid boot DOS partition on your first hard disk
  400.     * the power cables may be loose
  401.     * the data cables may be loose
  402.                            HELP - No Changes Made
  403.                            
  404.   No changes were made during this install session.  Press <Enter> to
  405.   return to the operating system.
  406.                        HELP - Memory Allocation Error
  407.                        
  408.   A memory allocation error has occurred.
  409.   You can possibly gain some additional memory by removing any TSRs or
  410.   memory-resident programs that you have loaded, and re-starting your
  411.   system.
  412.                 HELP - Automatic Installation Verification
  413.                 
  414.   The Install program is about to automatically install your blank hard
  415.   disk(s).
  416.   To continue with this operation, press <Enter>.  The installation
  417.   software will partition and format your blank hard disk(s) to the
  418.   maximum size allowed by the operating system or of the disk.
  419.   Manual Installation lets you set the number and sizes of partitions on
  420.   your hard disks.  In Manual mode, you can also delete and reformat
  421.   existing partitions.
  422.   Options lets you configure several disk formatting options.
  423.                            HELP - Delete Volume
  424.                            
  425.   All of the volumes on this disk have been deleted.
  426.   You can create new volumes by choosing Create Volumes in the Volume
  427.   Configuration menu.
  428.   You can save the changes by pressing <Esc> to return to the Hard Disk
  429.   Configuration menu and choosing the Save Changes menu option, or
  430.   discard these changes using the Cancel Changes menu option.
  431.   Press <Esc> to return to the Select Hard Disk menu after saving the
  432.   changes.
  433.               HELP - Continue Automatic Installation Mode
  434.               
  435.   You have selected the BIOS drive-type for the hard disk that you are
  436.   installing and verified that the selection you made is correct.
  437.   When you continue the Automatic Installation the Install program will:
  438.    - update the CMOS to the drive-type you have chosen
  439.    - partition and format the hard disk
  440.    - copy the system files to the hard disk (if applicable)
  441.    - create or change the CONFIG.SYS file on the boot drive (if
  442.        applicable)
  443.    - copy the Quantum IDE DOS device driver (IDE_DOS.SYS) to the boot
  444.        drive (if applicable)
  445.    - prompt you to reboot the system
  446.   To continue the Automatic Installation Mode, press <Enter>.
  447.                           HELP - No Changes to Save
  448.                           
  449.   You have not created or deleted any volumes on the selected hard disk
  450.   since you selected the hard disk or since the last save, so there is
  451.   nothing to save.
  452.   To select another hard disk, press <Esc> to return to the Select Hard
  453.   Disk menu.
  454.                            HELP - Cancel Changes
  455.                            
  456.   You have defined changes (set or changed BIOS drive-type and created
  457.   or deleted volumes) on the selected hard disk that have not been
  458.   saved.  If you continue, these changes will be lost and your hard disk
  459.   will not be changed.  If you want to implement these changes at a
  460.   later time, you will have to re-enter them at that time.
  461.   If you would like to continue and lose the modifications that you have
  462.   defined for this hard disk, press <Enter>.
  463.   If you would like to return to the Hard Disk Configuration menu to
  464.   save these modifications, press <Esc>.
  465.                              HELP - Save Changes
  466.                              
  467.   You have defined changes (set or changed the BIOS drive-type, and
  468.   created or deleted volumes) on the selected hard disk.  Up until this
  469.   point, the hard disk has not actually been modified; your changes have
  470.   been kept track of by the installation program in program memory.  If
  471.   you continue, however, these changes will be saved to your hard disk.
  472.   If you would like to continue and save these modifications on the
  473.   selected hard disk, press <Enter>.
  474.   If you would like to make additional modifications or to cancel these
  475.   modifications, select the appropriate menu option and press <Enter>.
  476.                       HELP - Set CMOS Configuration
  477.                       
  478.   Set CMOS Configuration lets you select one of the following for the
  479.   Install program to use when initializing the hard disk.
  480.    - the optimal drive-type from the computer's standard drive-type table
  481.    - the optimal drive-type from the computer's extended drive-type
  482.       table, if supported by this computer
  483.    - the Quantum IDE_DOS device driver which lets you access the total
  484.       capacity of the hard drive
  485.    - any drive-type from the computer's drive-type table
  486.  The CMOS configuration must be set before volumes can be configured.
  487.                        HELP - View CMOS Configuration
  488.                        
  489.   View CMOS Configuration will display the computer's BIOS drive-type
  490.   that is currently set in CMOS for this drive.  It will also display
  491.   the drive's true configuration (which may not match the CMOS setting).
  492.                            HELP- Previous Menu
  493.                            
  494.   Previous Menu will return the program back to the menu that was
  495.   displayed prior to the one currently being displayed.
  496.                         HELP - Insert System Disk
  497.                         
  498.   The Install program is now updating your hard disk to make it
  499.   bootable.  To do this you must insert the system (boot) disk from
  500.   which you originally booted the system (or a disk with the exact same
  501.   version of the operating system) so that the system files may be
  502.   copied from it.
  503.   If you do not insert the proper disk, you will not be able to continue
  504.   with the installation.
  505.                           HELP - Cannot Open File
  506.                           
  507.   The Install program cannot open the file specified in the error
  508.   message.
  509.   Please check that the file exists.
  510.   If it does, check to make sure all cables are connected and that the
  511.   power to the hard disk is on.
  512.   If the problem persists, you might have a defective hard disk.
  513.   Contact your local dealer or Quantum Corporation.
  514.                           HELP - Cannot Write File
  515.                           
  516.   The Install program cannot write the file specified in the error
  517.   message.
  518.   Please make sure all cables are connected and the power to the hard
  519.   disk is on.
  520.   If all cables are connected and the power is on, delete the volume you
  521.   created and re-create it.
  522.   If the problem persists, you might have a defective hard disk.
  523.   Contact your local dealer or Quantum Corporation.
  524.                            HELP - Cannot Copy File
  525.                            
  526.   The Install program cannot copy the file specified in the error
  527.   message.
  528.   Please check that the source file exists.
  529.   If it does, check to make sure all cables are connected and that the
  530.   power to the hard disk is on.
  531.   If the problem persists, you might have a defective hard disk.
  532.   Contact your local dealer or Quantum Corporation.
  533.                        HELP - Cannot Find System Files
  534.                        
  535.   The Install program cannot find the system files specified in the
  536.   error message.
  537.   Please check that the files exist.
  538.   If they do, check to make sure all cables are connected and that the
  539.   power to the hard disk is on.
  540.   If the problem persists, you might have a defective hard disk.
  541.   Contact your local dealer or Quantum Corporation.S
  542.                     HELP - Set CMOS Configuration
  543.                     
  544.   Standard Drive-Type:  Displays the drive-type from the standard BIOS
  545.   drive-type table that is closest to matching the full capacity of the
  546.   selected hard disk.  Selecting this menu option specifies that the
  547.   Install program will use the displayed standard drive-type.
  548.   Extended Drive-Type:  Displays the drive-type from the extended BIOS
  549.   drive-type table that is closest to matching the full capacity of the
  550.   selected hard disk, if this computer supports extended drive-types.
  551.   If this computer does not support extended drive-types, the message
  552.   None Available is displayed, and this menu option is disabled.
  553.   Selecting this menu option, if enabled, specifies that the Install
  554.   program will use the displayed extended drive-type.
  555.   <PgDn>                                                      Page 1 of 2
  556.                     HELP - Set CMOS Configuration
  557.                     =============================
  558.   Software Driver:  Select this menu option to specify that the Install
  559.   program will automatically install the Quantum DOS device driver
  560.   (IDE_DOS.SYS) to make use of the full capacity of the hard disk
  561.   regardless of the BISO drive-type used.
  562.   Select Drive-Type from List:  Selecting this menu option displays a
  563.   table of usable selections from the standard BIOS drive-type table for    you to select a drive-type from.  The list will also include extended
  564.   BIOS drive-types if the option "Use Extended BIOS Table When Setting
  565.   CMOS" is "Yes".  Use the <F2> Options key to change this setting.
  566.                                <Esc> Cancel                   Page 2 of 2
  567.                 HELP - Select BIOS Drive-Type From Table
  568.                 
  569.   Use the up (
  570. ) and down (
  571. ) arrow keys to move the highlight bar
  572.   selection in the table that you wish to use and press <Enter>.
  573.   Drive-type selections are sorted in the table by total disk space
  574.   available and percentage of total disk space used.
  575.   To select a different CMOS configuration option, press <Esc> to
  576.   return to the Set CMOS Configuration menu.
  577.              HELP - Confirm BIOS Drive-Type Selection
  578.              
  579.   Information regarding the BIOS drive-type you have selected to use
  580.   with this hard disk is displayed.  If you selected the Software
  581.   Driver, the total capacity of the hard disk is displayed, and
  582.   "Quantum Device Driver" is displayed for type, cylinders, heads and
  583.   sectors.
  584.   To confirm your decision to use the displayed selection and continue
  585.   with installation, press <Enter>.
  586.   If you do not like the displayed selection, and you would like to
  587.   make another selection, press <Esc> to return to the Hard Disk
  588.   Configuration menu.
  589.               HELP - No CMOS Drive-Type Match Found In Tables
  590.               
  591.   The Install program did not find a close drive-type match for the hard
  592.   disk you are initializing in this system's BIOS drive-type tables.  If
  593.   the "Use Extended BIOS Tables When Setting CMOS" menu option in the
  594.   Select Option menu is disabled, the Install program searched the
  595.   standard CMOS drive-type tables.  If the "Use Extended BIOS Tables
  596.   When Setting CMOS" menu option in the Select Option menu is enabled,
  597.   and this computer supports extended drive types, the Install program
  598.   searched the extended BIOS drive-type tables.
  599.   You must now select a drive-type for the hard disk you are
  600.   initializing to continue with the installation.
  601.   Press <Enter> to continue.
  602.                        HELP - View CMOS Configuration
  603.                        
  604.   View CMOS Configuration displays two different sets of information
  605.   about the current drive.
  606.   The first set of information is what the drive-type value in CMOS
  607.   reports about the hard disk in terms of its physical characteristics.
  608.   It need not match the true physical characteristics of the hard disk
  609.   as long as the total capacity of this drive-type does not exceed the
  610.   true capacity of the hard disk.  The "Usage" field shows how much of
  611.   the hard disk will be made available with this particular drive-type.
  612.   The second set of information is what the hard disk reports its
  613.   true physical characteristics to be.  If your computer supports a
  614.   user-definable drive-type, these are the values you should use when
  615.   running your computer's SETUP program to define the drive-type.
  616.                    HELP - Changing CMOS Configuration
  617.                    
  618.   This screen is indicating that you have decided to change the CMOS
  619.   setting of this hard disk's BIOS drive-type.  If you continue from
  620.   this point the drive's configuration will be changed and you will lose
  621.   all data that is already on the hard disk.
  622.   If you wish to save the data already on the hard disk, press <Esc>
  623.   until the program returns to the Select Hard Disk screen, exit the
  624.   program, and back up your data before restarting the Install program.
  625.   To continue working on this hard disk, and lose any data on the disk,
  626.   press <Enter>.
  627.                   HELP - CMOS Configuration Invalid
  628.                   
  629.   The CMOS Configuration for this hard disk has not been set or is set
  630.   to a BIOS Drive-Type that describes a hard disk with a larger
  631.   capacity than the currently selected hard disk.
  632.   You must set the BIOS drive-type to a valid Drive-Type before you can
  633.   partition the volumes for this hard disk.
  634.   To continue working on this hard disk, press <Enter>.
  635.   Then use the up (
  636. ) and down (
  637. ) arrow keys to move the highlight bar
  638.   to the Set CMOS Configuration option and press <Enter>.
  639.                           HELP - Cancel Changes
  640.                           
  641.   If you select Cancel Changes, the changes you made to the CMOS
  642.   settings and hard disk volumes will be discarded.  The drive will be
  643.   left in the same state that it was in before you started the Install
  644.   program.  This is your "escape hatch" if you have changed your mind
  645.   and don't want to alter the disk and/or destroy the data that was on
  646.   it previously.
  647.                         HELP - CMOS Configuration
  648.                         
  649.   You can set or change the CMOS configuration, set the volume
  650.   configuration, and save or cancel changes made to the hard disk.
  651.   CMOS Configuration lets you set the BIOS drive-type for the selected
  652.   hard disk.  The Install program will display the optimum drive-type
  653.   from this computer's standard drive-type table and, if available,
  654.   the extended drive-type table.  You will also be able to select the
  655.   Quantum IDE DOS device driver which lets you access the total capacity
  656.   of the hard disk, regardless of drive-type, or you may make your own
  657.   selection from the computer's drive-type table.
  658.                        HELP - Volume Configuration
  659.                        
  660.   You can set or change the CMOS configuration, set the volume
  661.   configuration, and save or cancel changes made to the hard disk.
  662.   Volume Configuration lets you create and name volumes of any size up
  663.   to the maximum allowed by the operating system on the hard disk.  To
  664.   create a volume, you must have a blank (unformatted) space on the hard
  665.   disk you have selected.
  666.   A volume must be created in a contiguous space on the hard disk.
  667.              HELP - BIOS Drive-Type Setting Not Optimal
  668.              
  669.   The BIOS drive-type that is currently set for this hard disk is not
  670.   the best, or optimal, selection available in this computer's BIOS
  671.   drive-type table.
  672.   If you wish to continue the installation and use the currently set
  673.   drive-type, you will not be able to access the total capacity of the
  674.   hard disk.  To continue, press <Enter>.
  675.   To select another BIOS drive-type for use, press <Esc> to return to
  676.   the Hard Disk Configuration menu.  Then use the up (
  677. ) and down (
  678.   arrow keys to select the CMOS Configuration option and set another
  679.   BIOS drive-type.
  680.                   HELP - Abort Automatic Installation
  681.                   
  682.   You may either abort automatic installation of the currently selected
  683.   hard disk, or continue the automatic installation sequence.
  684.   To abort automatic installation of this hard disk, use the up (
  685. ) and
  686.   down (
  687. ) arrow keys to select the Yes option and press <Enter>.  If
  688.   there are no other uninstalled hard disks in the system, the Install
  689.   program will return you to the DOS prompt.
  690.   To continue the automatic installation of this hard disk, use the up
  691. ) and down (
  692. ) arrow keys to select the NO option and press <Enter>.
  693.                  HELP - Continue Installing The Next Volume
  694.                  
  695.   You may either abort this installation process, or you may continue
  696.   the installation with the next hard disk volume.
  697.   To abort this installation, use the up (
  698. ) and down (
  699. ) arrow keys to
  700.   select the No option and press <Enter>.
  701.   To continue this installation with the next hard disk volume, use the
  702.   up (
  703. ) and down (
  704. ) arrow keys to select the Yes option and press
  705.   <Enter>.
  706.               HELP - Continue Installing The Next Hard Disk
  707.               
  708.   You may continue the automatic installation of the second hard disk in
  709.   your system, or abort the automatic installation and return to the DOS
  710.   prompt.
  711.   To abort the automatic installation, use the up (
  712. ) and down (
  713. ) arrow
  714.   keys to select the No option and press <Enter>.
  715.   To continue the automatic installation, use the up (
  716. ) and down (
  717.   arrow keys to select the Yes option and press <Enter>.
  718.     HELP - Using The Quantum Software Driver With Windows 3.1 FastDisk
  719.   If you are installing the Quantum IDE DOS device driver (IDE_DOS.SYS)
  720.   and you wish to use the FastDisk feature of Windows 3.1, you must
  721.   use the Quantum FastDisk device driver (IDE_WIN.386) rather than the
  722.   one provided with Windows.  After installing your hard disk, install
  723.   Windows.  Then install IDE_WIN.386 using the Quantum FastDisk
  724.   installation program (SETUP.EXE).
  725.