SCANNING FROM PRODOS
MATT GULICK
This article shows just how easy it is to include support for scanner hardware in your application program. With just a little effort, you can add significant functionality to your program.
In this article, we explore using the Apple Scanner (a flatbed scanner) and the
Apple II High-Speed SCSI Card with either an Enhanced Apple IIe computer or
an Apple IIGS computer running the ProDOS-8 operating system. (A future article will cover
GS/OS.) The concepts presented here can be used for any scanner that can be connected to an
Apple IIe or Apple IIGS via the Apple II SCSI card.
For this article, we limit our discussion to the graphics modes available on the Apple IIe (HiRes and Double HiRes modes). These modes are more limited in resolution and color generation than the Super HiRes mode available on the IIGS, but they allow our sample program to run on most of the current Apple II family of systems in use today. We focus on 1-bit-per-pixel halftone and line art images. In so doing, we are able to display the data on the screen easily.
PLAYING HIDE-AND-SEEK WITH THE SCANNER
...98, 99, 100. Ready or not, here we come. Under the ProDOS-8 operating system, we don't have access to the loaded drivers that have been written for the GS/OS environment. Since the scanner is a character device, data is returned in bytes rather than in blocks. ProDOS-8 can't help us read from character devices, so we need to walk the slots looking for the card we want and then talk to the card directly to find the device we want.APPLE HIGH-SPEED SCSI CARD, WHERE ARE YOU?
We must first find which slot the high-speed SCSI card is in. We start at slot 7 and work our way
down. In the following code segment, we look for a SmartPort device in the current slot. If one is
found, we must determine if it is a SCSI card that supports extended SmartPort calls. Finally, we
need to make sure that this is the
type of card we want. In other words, "Is this card from a vendor whose command set I understand?"
See Code Sample 1.
;******************************************************* ; ; CODE SAMPLE 1 ; ; In this first code segment, we walk the slots starting ; at slot 7, looking first for a card of any kind. Once ; found, we check the ID bytes for a SmartPort card. ; Once found, we check the ID Type byte to see if it is ; a SCSI card. If the card passes all these tests, we ; then issue a Device $00 Status $00 call to further ; ensure that this is the Apple II High-Speed SCSI Card. ; ;******************************************************* find_card ; ; Save the current Zero ; Page values before ; using them. ; lda <My_ZPage pha lda <My_ZPage+1 pha ; ; Start at slot 7. ; lda #slot_7 sta <My_ZPage+1 ;Zero Page sta slot+1 ;For Safe keeping stz <My_ZPage stz slot ; ; Is it a SmartPort card? ; @chk_smart ldy #Blk_sigl lda (My_ZPage),y ;Block_device Signature Byte cmp #$20 ;#1 = $20 bne @next_slot ldy #Blk_sig2 lda (My_ZPage),y ;Block_device Signature Byte bne @next_slot ;#2 = $00 ldy #Blk_sig3 lda (My_ZPage),y ;Block_device Signature Byte cmp #$03 ;#3 = $03 bne @next_slot ldy #SPort_sig lda (My_ZPage),y ;SmartPort Signature Byte bne @next_slot ;#1 = $00 ; ; We have a SmartPort ; device. Is it SCSI with ; Extended SmartPort? ; ldy #SPort_ID lda (My_ZPage),y and #Ext_SPort+\ SCSI cmp #Ext_SPort+\ SCSI bne @next_slot ; ; Is it an Apple II ; High-Speed SCSI Card? ; jsr is_it_appl bcc @exit ; ; Check the next slot. ; @next_slot lda <My_ZPage+1 dec a sta <My_ZPage+1 sta slot+1 cmp #slot_1 bge @chk_smart lda #No_dev ;No Device Error ; ; Clean exit ; @exit tax pla sta <My_ZPage+1 pla sta <My_ZPage txa cmp #$01 ;Set Carry if Non-Zero. rts ; ; This routine determines ; if the card is the new ; high-speed SCSI card. ; is_it_appl ldy #$ff lda (My_ZPage),y clc adc #$03 ;Set SmartPort Entry Address. sta card_ntry lda <My_ZPage+1 sta card_ntry+1 jsr call_card dc.b $00 ;Status Call Command Number dc.w stat_list1 ; ; Check the results. ; lda stat_data+2 ;Low Byte of Vendor ID cmp #$01 ;Must be $01 bne @non_apple lda stat_data+3 ;High Byte of Vendor ID bne @non_apple ;Must be $00 lda stat_data+4 ;Low Byte of Version bne @non_apple ;Should be Null lda stat_data+5 ;High Byte of Version bne @non_apple ;Should be Null clc ;Acc. 0 by previous LDA bra @done @non_apple lda #No_dev ;Device not found sec ; ; Restore ZPage. ; @done pha php lda slot sta <My_ZPage lda slot+1 sta <My_ZPage+1 plp pla rts slot dc.w $0000 ;******************************************************* call_card jmp (card_ntry) card_ntry dc.w $0000 ;******************************************************* stat_list1 dc.b $03 ;PCount = 3 dc.b $00 ;Device = Card dc.w stat_data ;Data returned here dc.b $00 ;Get Host Status Call ;******************************************************* stat_data dcb.b 64,0 ;Our Buffer ;*******************************************************
FINDING THE SCANNER IN A HAYSTACK
Now that we've found the card, or at least a card (there may be more
than one), we need to ask the card, politely of course, if it has seen
the scanner and if so, where. See Code Sample 2.
"Excuse me SCSI card, we're taking a census and would like to ask you a few questions if you don't mind. How many devices live at this slot? I see, and are any of them by chance character devices? Hmmm, too bad. I'll try the next slot. Sorry to bother you, and thank you for your time."
. . . a few slots later . . ."Hi, we're taking a poll and would like your response to a few short questions. How many devices live at this slot? That many, great. Are any of them character devices? Getting warmer. May we come in to talk to them? Thank you."
;******************************************************* ; ; CODE SAMPLE 2 ; ; In this code segment, we walk the unit numbers from the ; SCSI card starting at unit 2 and going to unit 0 to ; get the actual unit number count. Once this is ; done, we start at unit 1 and walk forward until we ; find the scanner. ; ;******************************************************* find_scanr ; ; First we issue a ; Status call to device ; number 2. This call ; forces the card to ; build its tables if it ; has not yet done so. ; lda #$02 sta dev_num2 stz stat_code2 jsr call_card dc.b $00 ;Status Call Command Number dc.w stat_list2 bcs @error ; ; Now call unit 0 to ; find out the total ; device count. ; stz dev_num2 jsr call_card dc.b $00 ;Status Call Command Number dc.w stat_list2 bcs @error lda stat_data2 ;Get the Total Device sta dev_count ;Count. lda #$03 ;Set up for DIB Status sta stat_code2 ;calls. @loop lda dev_num2 ;First time we increment cmp dev_count ;a zero giving a device bge @error ;number of 1. inc dev_num2 jsr call_card dc.b $00 ;Status Call Command Number dc.w stat_list2 bcs @error lda d_type cmp #$08 ;Is it Type = Scanner? bne @loop ;No lda d_stype cmp #$A0 ;Subtype = $A0? bne @loop ;No ; ; Scan string is a Pascal ; string (a length byte ; followed by ASCII). We ; want to make sure that ; both the length and the ; text in 'scan_str' match ; the data returned in ; 'id_str_len' and 'id_str'. ; ldx id_str_len @str_loop lda id_str_len,x cmp scan_str,x bne @loop dex bne @str_loop lda dev_num2 ;We have our scanner. sta scan_dnum lda #No_Err clc rts @error lda #No_dev ;Device not found. sec rts ;******************************************************* scan_str dc.b 'APPLE SCANNER ';4 Spaces between ;1 Space after dev_count dc.b $00 ;******************************************************* scan_dnum dc.b $00 ;Scanner Device Number ;******************************************************* stat_list2 dc.b $03 ;PCount = 3 dev_num2 dc.b $00 ;Device number dc.w stat_data ;Data returned here stat_code2 dc.b $00 ;Status Code ;******************************************************* stat_data2 ;Our Buffer. Used over. d_stat dc.b $00 ;Device Status Byte blk_low dc.b $00 ;Block Count (Low) blk_mid dc.b $00 ;Block Count (Mid) blk_hi dc.b $00 ;Block Count (High) id_str_len dc.b $00 ;ID String Length id_str dcb.b 16,$00 ;ID String (16 Bytes) d_type dc.b $00 ;Device Type d_stype dc.b $00 ;Device Subtype d_version dc.w $00 ;Version Word ;*******************************************************
SCANNING FOR 'STILL LIFE' FORMS, CAPTAIN
Now that we've found the scanner, we're ready to plant our thoughts in it. We do this by sending a few commands to the scanner, telling it what type of image we expect and what the scanner should do with the image before transferring it to us.WE ARE ONE--OUR THOUGHTS ARE YOUR THOUGHTS
First, we send the scanner the halftone filter we want to use; then we set our scan window.
Halftone filter. Since we're going to do a halftone scan in our example, we issue a call to set the halftone filter. Note that we don't need to set this halftone filter if we choose to use one of the default filters or if we are going to scan in Line Art mode. A halftone filter is nothing more than a defined threshold for each pixel of a 4 by 4 block. As the image under the mask changes intensity, the filter causes more or fewer of the dots to be black; the rest of the dots are white. The 4 by 4 block then becomes darker or lighter depending on the number of dots that are set to white within it, simulating gray tones even though our graphic mode knows only black and white.
Setting the halftone filter is easy; picking the filter pattern that best suits your needs is harder. Use one of the built-in patterns unless you have a better one. We use a simple Bayer type filter for this example. See Figure 1 and Code Sample 3.
Figure 1 Simple Bayer Pattern
;******************************************************* ; ; CODE SAMPLE 3 ; ; In this code segment, we issue an Apple Scanner SEND ; command by using the Apple SCSI Card Generic SCSI ; call ($2B). By so doing, we can send our halftone ; filter to the scanner. ; ;******************************************************* htone_filter ; ; Issue the call. ; lda scan_dnum sta dev_num3 jsr call_card dc.b $04 ;Control Call Command Number dc.w cmd_list3 rts ;******************************************************* cmd_list3 dc.b $03 ;PCount = 3 dev_num3 dc.b $04 ;Device number dc.w filter_data ;Pointer to data dc.b $2B ;Control Code ;******************************************************* filter_data ;Our Data dc.w 24 ;Total Length of Parms dc.l send_fltr ;CDB Pointer (Long) dc.l DCData3 ;DCMove Ptr (Long) dc.l $00000000 ;Rqst Sense Ptr (Long) dc.b $00 ;Reserved dc.b $00 ;SCSI Status dc.b $00 ;Command Count dc.l $00000011 ;Trans Count (Long) dc.b $00 ;DMA Mode dc.l $00000000 ;Reserved (Long) ;******************************************************* send_fltr dc.b $2A ;Scanner SEND Command dc.b $00 ;Reserved dc.b $02 ;Transfer Type dc.b $00 ;Reserved dc.b $00 ;Reserved dc.b $02 ;Transfer ID Byte dc.b $00 ;Reserved dc.b $00 ;Transfer Length (High) dc.b $11 ;Transfer Length (Low) dc.b $00 ;Reserved ;******************************************************* DCData3 dc.l send_data ;Scanner SEND Data Ptr dc.l $00000011 ;Transfer Count dc.l $00000000 ;Offset dc.l $00000000 ;Reserved dc.l $00000000 ;DCStop dc.l $00000000 ;Reserved dc.l $00000000 ;Reserved dc.l $00000000 ;Reserved ;******************************************************* send_data dc.b $44 ;4 X 4 Matrix Size dc.b $08 ;Pel 0 dc.b $88 ;Pel 1 dc.b $28 ;Pel 2 dc.b $A8 ;Pel 3 dc.b $C8 ;Pel 4 dc.b $48 ;Pel 5 dc.b $E8 ;Pel 6 dc.b $68 ;Pel 7 dc.b $38 ;Pel 8 dc.b $B8 ;Pel 9 dc.b $18 ;Pel 10 dc.b $98 ;Pel 11 dc.b $F8 ;Pel 12 dc.b $78 ;Pel 13 dc.b $D8 ;Pel 14 dc.b $58 ;Pel 15 ;*******************************************************Our scan window. Now that the scanner knows what halftone filter to use, we need to describe the scan window through which we'll view the document. Because we're using one of the Apple IIe graphics modes, our window will be fairly small. At 75 dpi in HiRes mode, or 150 dpi in Double HiRes mode, our window is about 3.75 inches across.
For the vertical screen, we have 192 pixels. At 75 dpi, our window is about 2.5 inches tall.
By using 75 dpi for HiRes and 150 dpi for Double HiRes, we can maintain a good aspect ratio. This allows us to display an image with minimum distortion.
In our example we use Double HiRes, so we first set the resolution for the X axis to 150 dpi and for the Y axis to 75 dpi. Then, we set our scan window's upper-left corner to absolute zero. See Code Sample 4.
;******************************************************* ; ; CODE SAMPLE 4 ; ; In this code segment, we issue an Apple Scanner ; DEFINE WINDOW PARAMETERS command by using the Apple ; SCSI Card Generic SCSI call ($2B). This command ; defines the area of the scanner glass we want to scan. ; ;******************************************************* def_window ; ; Issue the call. ; lda scan_dnum sta dev_num4 jsr call_card dc.b $04 ;Control Call Command Number dc.w cmd_list4 rts ;******************************************************* cmd_list4 dc.b $03 ;PCount = 3 dev_num4 dc.b $00 ;Device number dc.w def_wndo ;Pointer to data dc.b $2B ;Control Code ;******************************************************* def_wndo ;Our Data dc.w 24 ;Total Length of Parms dc.l def_wnd_cmd ;CDB Pointer (Long) dc.l DCData4 ;DCMove Ptr (Long) dc.l $00000000 ;Rqst Sense Ptr (Long) dc.b $00 ;Reserved dc.b $00 ;SCSI Status dc.b $00 ;Command Count dc.l 8+40 ;Trans Count (Long) dc.b $00 ;DMA Mode dc.l $00000000 ;Reserved (Long) ;******************************************************* def_wnd_cmd dc.b $24 ;Scanner Define Window ;Parameters Command dc.b $00 ;Reserved dc.b $00 ;Reserved dc.b $00 ;Reserved dc.b $00 ;Reserved dc.b $00 ;Reserved dc.b $00 ;Transfer Length (High) dc.b $00 ;Transfer Length (Mid) dc.b 8+40 ;Transfer Length (Low) dc.b $80 ;Apple Bit ;******************************************************* DCData4 dc.l wndo_data ;Scan Window Data Ptr dc.l 8+40 ;Transfer Count dc.l $00000000 ;Offset dc.l $00000000 ;Reserved dc.l $00000000 ;DCStop dc.l $00000000 ;Reserved dc.l $00000000 ;Reserved dc.l $00000000 ;Reserved ;******************************************************* ; NOTE: Remember that all values longer than 1 byte ; are in reverse order from native 65xxx code. ;******************************************************* wndo_data dcb.b 6,$00 ;Reserved dc.b $00 ;Transfer Length (High) dc.b 40 ;Transfer Length (Low) dc.b $01 ;Window Identifier dc.b $00 ;Reserved dc.b $00 ;X Resolution (High) dc.b 150 ;X Resolution (Low) dc.b $00 ;Y Resolution (High) dc.b 75 ;Y Resolution (Low) ; ; We will use the corner as ; our upper-left position. ; This is at coordinate 0,0. ; dc.b $00 ;Upper Left X (High) dc.b $00 ;Upper Left X (Mid High) dc.b $00 ;Upper Left X (Mid Low) dc.b $00 ;Upper Left X (Low) dc.b $00 ;Upper Left Y (High) dc.b $00 ;Upper Left Y (Mid High) dc.b $00 ;Upper Left Y (Mid Low) dc.b $00 ;Upper Left Y (Low) ; ; Width is defined as the number ; of 1/1200-inch increments on ; the horizontal axis; must be on ; a byte boundary for both the ; start and end points. We will ; set for 4 inches and drop the ; extra. ; dc.b $00 ;Width (High) dc.b $00 ;Width (Mid High) dc.b 4*1200/256 ;Width (Mid Low) dc.b 4*1200 ;Width (Low) ; ; Length is defined as the number. ; of 1/1200-inch increments on the ; vertical axis. We want ≈ 2-1/2 ; inches (or 3072 increments). ; dc.b $00 ;Length (High) dc.b $00 ;Length (Mid High) dc.b 3072/256 ;Length 2.56*1200 (Mid Low) dc.b 3072 ;Length 2.56*1200 (Low) dc.b $80 ;Median Brightness dc.b $80 ;Median Threshold dc.b $80 ;Median Contrast dc.b $01 ;Image Composition (Halftone) dc.b $01 ;Bits per Pixel dc.b $00 ;Halftone Mask Always $00 (High) dc.b $02 ;Downloaded Mask Pattern (Low) dc.b $03 ;Padding Type dcb.b 2,$00 ;Reserved dc.b $00 ;Compression Type (None) dcb.b 7,$00 ;Scanner Ref. is wrong ; should be 7, ; not 5. ;*******************************************************
ENGAGE SCANNER
After telling the scanner how to scan, we need to tell it to start scanning.
See Code Sample 5.
;******************************************************* ; ; CODE SAMPLE 5 ; ; This code segment issues an Apple Scanner SCAN ; command by using the Apple SCSI Card Generic SCSI ; call ($2B). This starts the actual scanning. ; ;******************************************************* start_scan ; ; Issue the call. ; lda scan_dnum sta dev_num5 jsr call_card dc.b $04 ;Control Call Command Number dc.w cmd_list5 rts ;******************************************************* cmd_list5 dc.b $03 ;PCount = 3 dev_num5 dc.b $00 ;Device number dc.w scan_cmd ;Pointer to data dc.b $2B ;Control Code ;******************************************************* scan_cm ;Our Data dc.w 24 ;Total Length of Parms dc.l do_scan ;CDB Pointer (Long) dc.l DCData ;DCMove Ptr (Long) dc.l $00000000 ;Rqst Sense Ptr (Long) dc.b $00 ;Reserved dc.b $00 ;SCSI Status dc.b $00 ;Command Count dc.l $00000001 ;Trans Count (Long) dc.b $00 ;DMA Mode dc.l $00000000 ;Reserved (Long) ;******************************************************* do_scan dc.b $1B ;SCAN ;Parameters Command dcb.b 3,$00 ;Reserved dc.b 1 ;Transfer Length (Low) dc.b $00 ;Wait and Home Bits = 0 ;******************************************************* DCData5 dc.l window_ID ;Scan Window ID Ptr dc.l 1 ;Transfer Count dc.l $00000000 ;Offset dc.l $00000000 ;Reserved dc.l $00000000 ;DCStop dc.l $00000000 ;Reserved dc.l $00000000 ;Reserved dc.l $00000000 ;Reserved ;******************************************************* window_ID dc.b $01 ;Window Identifier ;*******************************************************
ENERGIZING!
We can get data from the scanner in two ways. We could get it all at
once and then manipulate it to go on the screen. In our example, we
would need a buffer with 115,200 pixels or 14,400 bytes for the data:
(4.0 inches * 150 dpi horizontally) * (2.56 inches * 75 dpi vertically).
To save the amount of RAM our program uses, however, we set up a buffer large enough for only one line; then we read each line from the scanner and display it until the entire image is on the screen. See Code Sample 6.
The data returned by the scanner is 8 pixels per byte. Bit 7 is the left- most pixel and bit 0 is the right-most pixel; a value of 1 means a black dot in the image. In the Apple II HiRes mode, we have 7 pixels per byte. Bit 0 is the left-most pixel and bit 6 is the right-most pixel; a value of 1 means a white dot. Because the formats are different, the program must convert the returned data, which it does as it goes, using code shown in Code Sample 6.
******************************************************* ; ; CODE SAMPLE 6 ; ; In this code segment, we issue a series of calls to ; the Apple Scanner by using the Apple SCSI Card Generic ; SCSI call ($2B). We first issue a GET DATA STATUS ; call to see if there is enough data. Then we read ; in a single scan line with a READ call. The data is ; then converted and placed in a video buffer. ; ;******************************************************* get_data stz scan_line ;Init the scan line to 0. ; ; Issue the call. ; lda scan_dnum sta dev_num6 sta dev_num65 @get_data2 jsr call_card dc.b $04 ;Control Call Command Number dc.w cmd_list6 bcs @out ; ; Is there enough data? ; Enough data = 1 scan ; line of 4 inches at 150 ; dpi (or 600 pixels). At ; 8 pixels per byte, the ; data will be padded to ; 75 bytes. ; lda scan_data bne @have_line lda scan_data+1 bne @have_line lda scan_data+2 cmp #rqst_cnt ;Decimal 75 blt get_data ; ; We have the data. Read ; it. ; @have_line jsr call_card dc.b $04 ;Control Call Command Number dc.w cmd_list65 bcs @out ; ; Now we need to invert ; the data. ; lda #80 ;80 bytes/line for Double HiRes sta byte_count stz byte_index @loop_1 lda #$07 sta seven ;Pixels/byte @loop_2 ldx #rqst_cnt-2 asl raw_image+\ rqst_cnt-1 ;Shift bits out the top to @loop_3 rol raw_image,x :the next byte 1 at a time dex bpl @loop_3 ldx byte_index ;Shift the last bit into ror screen,x ;this byte. This reverses the dec seven ;bit ordering and takes 8 bits bne @loop_2 ;per byte down to 7. lsr screen,x inc byte_index dec byte_count bne @loop_1 ; ; Move data to scan line. ; ldx scan_line jsr on_screen inc scan_line bra @get_data2 @out lda #$00 clc rts ;******************************************************* scan_line dc.b $00 ;Scan Line Index byte_count dc.b $00 ;Number of bytes left byte_index dc.b $00 ;Current Byte in use seven dc.b $00 ;Count off 7 pixels screen dcb.b 80,0 ;Place to do the screen ;******************************************************* cmd_list6 dc.b $03 ;PCount = 3 dev_num6 dc.b $00 ;Device number dc.w gd_status ;Pointer to data dc.b $2B ;Control Code cmd_list65 dc.b $03 ;PCount = 3 dev_num65 dc.b $00 ;Device number dc.w read ;Pointer to data dc.b $2B ;Control Code ;******************************************************* gd_status ;Our Data dc.w 24 ;Total Length of Parms dc.l get_stat ;CDB Pointer (Long) dc.l DCData6 ;DCMove Ptr (Long) dc.l $00000000 ;Rqst Sense Ptr (Long) dc.b $00 ;Reserved dc.b $00 ;SCSI Status dc.b $00 ;Command Count dc.l $0000000C ;Trans Count (Long) dc.b $00 ;DMA Mode dc.l $00000000 ;Reserved (Long) read ;Our Data dc.w 24 ;Total Length of Parms dc.l get_data2 ;CDB Pointer (Long) dc.l DCData65 ;DCMove Ptr (Long) dc.l $00000000 ;Rqst Sense Ptr (Long) dc.b $00 ;Reserved dc.b $00 ;SCSI Status dc.b $00 ;Command Count dc.l rqst_cnt ;Trans Count (Long) dc.b $00 ;DMA Mode dc.l $00000000 ;Reserved (Long) ;******************************************************* get_stat dc.b $34 ;GET DATA STATUS ;Parameters Command dcb.b 7,$00 ;Reserved dc.b 12 ;Transfer Length (Low) dc.b $00 ;Wait and Home Bits = 0 get_data2 dc.b $28 ;READ ;Parameters Command dcb.b 4,$00 ;Reserved dc.b $01 ;Window ID dc.b $00 ;Transfer Length (High) dc.b $00 ;Transfer Length (Mid) dc.b rqst_cnt ;Transfer Length (Low) dc.b $00 ;Wait and Home Bits = 0 ;******************************************************* DCData6 dc.l data_cnt ;Data Pointer dc.l 12 ;Transfer Count dc.l $00000000 ;Offset dc.l $00000000 ;Reserved dc.l $00000000 ;DCStop dc.l $00000000 ;Reserved dc.l $00000000 ;Reserved dc.l $00000000 ;Reserved DCData65 dc.l raw_image ;Data Pointer dc.l rqst_cnt ;Transfer Count dc.l $00000000 ;Offset dc.l $00000000 ;Reserved dc.l $00000000 ;DCStop dc.l $00000000 ;Reserved dc.l $00000000 ;Reserved dc.l $00000000 ;Reserved ;******************************************************* data_cnt ;Data Space dcb.b 2,$00 ;Reserved dc.b $00 ;Data Length dc.b $00 ;Block dc.b $00 ;Window Identifier dcb.b 4,$00 ;Reserved scan_data dc.b $00 ;Scan Data (High) dc.b $00 ;Scan Data (Mid) dc.b $00 ;Scan Data (Low) raw_image dcb.b 100,$00 ;Scanned Data Image ;*******************************************************
PUT IT ON THE SCREEN, ENSIGN
Because we display the image in black and white, we need to set up the graphic soft switches
accordingly. In our example, we display our image in HiRes Page 1, and we assume black and white
display. On a color video monitor, the image would appear in black and white. See Code Sample 7.
;******************************************************* ; ; CODE SAMPLE 7 ; ; In this code segment, we toggle the HiRes soft ; switches so that we can see what was just scanned. ; ;******************************************************* display ; ; Save the current state. ; lda RDTEXT sta @text ;Text/Graphics lda RDMIX sta @mixed ;Mixed? lda RDPAGE2 sta @page ;Page 1 or 2 lda RDHIRES sta @hires ;HiRes Mode? lda RD80VID sta @80col ;80-Column Mode? sta SET80VID ;Set 80-Column Mode sta TXTCLR ;Standard Apple II Graphics sta MIXCLR ;Clear Mixed Mode sta TXTPAGE1 ;Page 1 sta HIRES ;HiRes Mode sta CLRAN3 ;Clear annunciator 3 sta KBD_STRB ;Clear Key Strobe @key_loop lda KBD ;Get key bpl @key_loop ;Wait for Key Press sta KBD_STRB ;Clear Key Strobe cmp #ESC ;ESC Key clc bne @chk_txt sec ;Exit on ESC lda SETAN3 ;Set annunciator 3. @chk_txt lda @text bpl @chk_mix sta TXTSET ;Text on @chk_mix lda @mixed bpl @chk_page sta MIXSET ;Mixed on @chk_page lda @page bpl @chk_hires sta TXTPAGE2 ;Page 2 @chk_hires lda @hires bmi @chk_40col sta LORES ;HiRes Off @chk_40col lda @80col bmi @rts sta CLR80VID ;80-Column on @rts rts @text dc.b $00 @mixed dc.b $00 @page dc.b $00 @hires dc.b $00 @80col dc.b $00 ;*******************************************************
FILE THE REPORT AND HEAD FOR HOME
Now, save the image in its displayable format. Save it as you would any file, using standard ProDOS
MLI calls.
FINAL LOG ENTRY
The ability to bring printed images into the computer opens up many possibilities for you and for
your customers. Programs that use graphics can import and add color to printed images. For
example, users can put together files that include family photos. These files can then be transmitted
electronically to others for viewing.
You can also give users control over a number of scan parameters. For example, you could allow them to position the scan window on a graphic representation of the scanner glass; users could then position the scan without adjusting the printed page on the scanner glass. Or you could allow users to specify the resolution of the scan, showing them how the scan window size changes.
Although not demonstrated here, Line Art mode provides very clean images of scanned text. If you use Line Art mode to support optical character recognition (OCR), users can import text and avoid retyping entire manuscripts.
The possibilities are endless. Have fun exploring them. That is, after all, what it is all about--doing more with your Apple II and having fun doing it.
THE SCANNING PROCESS
The scanning process involves five steps for your application, described briefly below. For general information about scanner technology and terminology, see the Apple Scanner Reference.
1. Initialize the scanner parameters
You must set the scanner parameters before you start a scan.
These parameters determine how much space the image needs.
Use these commands: MODE SENSE ($1A) MODE SELECT ($15) SEND ($2A) DEFINE WINDOW PARAMETERS ($24)
2. Define an image buffer
The image buffer is free memory within the computer system that holds the bitmap image returned by the
scanner. The size of the buffer dictates the amount of data you can retrieve from the scanner and thus the
size of the image. If an image is larger than the available free memory, you can spool it to disk for later
retrieval.
3. Start the scan
After you set the parameters, you can issue a scanner command to start scanning. When the scanner
receives this command, it scans the image and places it in its internal memory.
Use this command: SCAN ($1B)
4. Request the scanned data
You must read the image from the scanner as it is placed in the scanner's internal memory. Because the
scanner's memory can hold only a small portion of the image being scanned, and because you must read
the data to allow the scan to continue, you should poll the
scanner promptly.
Use these commands: GET DATA STATUS ($34) READ ($28)
5. Save the image to a file
You can save the data in a number of formats: HiRes and Double HiRes for the Apple II family, Super HiRes
for the Apple IIGS, and PICT or any other Macintosh image format. You can also store the data in other
formats, such as GIF. The choice is yours.
MATTHEW GULICK According to his business cards, Matt Gulick is an all-around SCSI (say it out loud) guy--who hates to shave and refuses to wear shoes except when meeting with someone with a title of VP or higher. He dearly loves the strict dress code, highly regimented working hours, and totally controlled environment at Apple. His career here was preordained by his being "genetically defective at birth." This condition first visibly manifested itself at age 12 when he began reading computer punch cards for fun. He did temporarily buck his computer industry destiny by studying pre-vet medicine at Brigham Young University. However, after college he got back on track by working as an "electronic stuff" sales rep, and then he programmed for ParaMIS. Now he feels he's running the perfect scam: getting paid to play with computers. A member of the Dr. Demento Fan Club (DDFC), he fears his wife will sue him for dementing his four children, who only know the Weird Al versions of song lyrics. *
You should let users adjust the settings for Brightness, Threshold, and Contrast so they can customize the scan to the type of image being scanned (black and white or color; printed page or photo). If you let users choose Line Art or Grayscale, they can also optimize the scan for text or for an image. *
- SPREAD THE WORD:
- Slashdot
- Digg
- Del.icio.us
- Newsvine