home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
DOS/V Power Report 1996 February
/
VPR9602A.ISO
/
drvlib
/
netcard
/
x86
/
octk32
/
readme.txt
< prev
Wrap
Text File
|
1995-10-27
|
14KB
|
354 lines
WINNT.DOC
Windows NT
==========
The installation procedure for Microsoft Windows NT(TM) and Windows
NT(TM) Advanced Server operating systems are the same. Both operating
systems will hereafter be referred to as "Windows NT".
During installation of the NDIS 3.0 MAC driver, you may find it
convenient to have the Windows NT System Guide at hand. Review the
"Configuring the Network" section in chapter 5 and chapter 19,
"Installing Windows NT" prior to installation.
The NDIS 3.0 MAC installation procedure described below will copy
all necessary set-up files to your Windows NT "System32" directory
and the driver to your "System32\Drivers" directory. In addition,
several changes will be made to your registry. Do not try to manually
change entries in the registry. All MAC driver parameters are
settable from the Network control panel.
Installation procedure:
=======================
The installation procedure for the NDIS 3.0 MAC driver allows
installation either during the initial Windows NT installation or
after Windows NT has been installed on your machine. If you
have already installed Windows NT on your machine, refer to the
"Adding adapter" section.
MAC Installation during Windows NT installation:
----------------------------------------------------
1 - Follow the instructions in the Windows NT System Guide to
begin Windows NT installation.
2 - If you have chosen custom set-up, you should choose "Do Not
Detect" when the "Network Adapter Card Detection" window
displays, as there is no netcard detection module included
with the Olicom MAC drivers.
3 - When the message "Set-up did not detect a network card" displays,
select "Continue" to go to the adapter card set-up phase.
4 - Continue with step 4 in the "Adding adapter" section below.
Adding Adapter:
---------------
If you are installing a network adapter after Windows NT has been
successfully installed on your system, you must be logged on with
administrative rights. This is necessary in order to be able to add,
configure and remove network adapters in Windows NT.
1 - Select the Control Panel in the Main window.
2 - Select the Network icon.
3 - In the Network Settings panel, choose the "Add adapter" button.
4 - In the list of Network Adapter Cards, select "<Other> Requires
disk from manufacturer" and press the "Continue" button.
5 - Enter the full path to the setup files for the desired adapter
type. If you are installing from the setup diskette, you should
enter "A:\NT".
6 - Confirm choice, by selecting proper adapter type and press the
"OK" button.
The setup program now copies installation files to your
harddisk.
7 - In the adapter configuration dialogue box, select proper values
for adapter settings. Refer to the "Adapter parameters" section
below for further details.
8 - Press the "OK" button when all parameters have been set
correctly.
The setup program now copies the NDIS 3.0 MAC driver to your
harddisk.
9 - You may wish to review the binding settings by selecting the
"Bindings" button. Press "OK" to return from the Network
Bindings windows.
10 - Select the "OK" button in the Network control panel, when
all adapters have been added.
11 - The settings will not take effect, until the system is
restarted. If Windows NT is installed on your system, system
restart can be initiated by selecting the "Yes" option in the
dialogue box shown when you exit the Network Control Panel.
Adapter parameters:
===================
When configuring an adapter, the following parameters can be
modified:
I/O Base Address : Must match the adapter I/O settings on the
installed adapter.
Bus Number : Identifies the bus number, the adapter has been plugged
into. For single-bus architectures, this value should be 0 (zero).
Early Token Release : Selects the early token release feature. This
parameter has only effect, when running 16 Mbps.
Full Transmit Status : When set to "Yes", normal transmit
verification is performed, and the upper layer drivers will be
notified about the status of the transmitted frame, i.e. whether the
destination address has been recognised and the frame has been copied
by the receiving station. When this value is "No", all transmitted
frames are assumed both recognised and copied by another station on
the ring. If you have a bridge/router in your network or discover
abnormal network behaviour, this value should be set to "Yes".
Network Address : If this entry is specified, the specified value
will be used in place of the universal burned-in node address on the
adapter card. Note that the entered address must be administered
locally. It must be entered as "XX-XX-XX-XX-XX-XX", e.g.
"40-00-12-34-56-78".
Using STAT.EXE to view adapter statistics:
==========================================
The STAT.EXE program is used to display adapter status and
statistics. This program is placed in the \NT\UTIL directory on
your diskette. In order to use the STAT.EXE utility you must have your
driver installed.
The program is called, using the following parameters:
STAT <adapter name> [options]
where
<adapter name>
- is <driver name><instance>. Notice: There is no space
character between <driver name> and <instance>.
<driver name>
- is the name of the driver, i.e. "Octk32".
<instance>
- is the instance number of the network adapter installed, i.e.
01, 02 etc.
[options]
- is one or more of the following
-c for adapter configuration. Default.
-a for additional adapter configuration
-s for general adapter statistics
-m for media specific statistics
Example:
STAT
shows the above option list.
STAT octk3201 -s
will show the statistics for the octk3201 driver.
Error messages:
===============
If you experience any problems with the network, you should check
if any error messages or warnings are posted by the MAC driver by
using the Event Viewer found in the Administrative Tools window. All
error messages and/or warnings posted by the Olicom MAC driver have
the Source field set to "OcTk16" or "OcTk32" depending on the adapter
installed. System error messages, related to the Olicom MAC driver,
may occur with different source names, i.e. "Service Control
Manager".
The messages are enumerated by the Event field and are described
below in Event number order. You can display the message description,
by highlighting the message and pressing enter.
Event Description
1 Bring-up diagnostics failed for OcTk3201.
Action: The adapter failed during the bring-up diagnostics.
Shut down your system and retry the operation. If the error
persist, contact your place of purchase.
2 Adapter initialize failed for OcTk3201.
Action: The adapter failed the initialization phase. Shut down
your system and retry the operation. If the error persist,
contact your place of purchase.
3 Adapter Check on OcTk3201.
Action: A serious error occurred on the adapter, causing an
Adapter check code to be posted. Restart your system. If the
error persist, contact your place of purchase.
4 Could not open adapter OcTk3201. Ring beaconing. Check network
speed settings.
Action: The network speed settings is wrong. Change it and
restart you system.
5 Could not open adapter OcTk3201. Duplicate node address.
Action: A duplicate address has been discovered on the ring.
Change your locally administered address as discussed in the
"Adapter parameter" section above and restart your system.
6 Could not open adapter OcTk3201. Request initialisation failed.
Action: An error occurred during adapter initialisation.
Restart your system. If the error persist, contact your place
of purchase.
7 Could not open adapter OcTk601. Remove station received.
Action: The adapter has been removed by a LAN Manager
station. Contact your network administrator.
8 Could not open adapter OcTk3201.
Action: The adapter failed to open. Please check cables and
connections and retry the operation.
9 Could not download code on adapter OcTk3201.
Action: The download operation failed. Contact your place of
purchase.
10 Lobe wire fault detected by OcTk3201. Please check cable
connections.
Action: Check all cables and connections and try another lobe
media cable. Retry the operation.
11 OcTk3201 has failed the lobe wrap test resulting from the
beacon auto-removal process and has deinserted from the ring.
Action: The adapter has deinserted from the ring, because the
ring was beaconing. Check the network speed settings and
cable connections and retry the operation. If the error
persist, contact your network administrator.
12 OcTk3201 has received a remove ring station Mac frame request
and has deinserted from the ring.
Action: The adapter has been removed by a LAN Manager
station. Contact your network administrator.
13 The detected adapter for OcTk3201 is not supported by this
driver.
Action: You have installed a wrong MAC driver for the adapter
used.
14 The configuration read for OcTk3201 is invalid.
Action: A configuration entry is invalid. Use the network
control panel to setup proper adapter settings.
15 OcTk3201 has received a Trace Tool Remove frame from a
Network Management station and has disabled the promiscuous
packet filter.
Action: The adapter driver has cleared the PROMISCUOUS packet
filter bit, as instructed by a LAN Manager station. Contact
your network administrator.
5000 OcTk3201 : Has encountered a conflict in resources and could
not load.
Action: Check the resources used by the network adapter(s) to
ensure, that no conflicts exists.
5001 OcTk3201 : Could not allocate resources necessary for
operation.
Action: The driver failed to load, because it tried to
allocate too many resources. Decrease the number of receive
and/or transmit buffers and retry the operation.
5002 OcTk3201 : Has determined that the adapter is not functioning
properly.
Action: The adapter could not be found or is not working
properly. Check I/O base settings and retry the operation.
5003 OcTk3201 : Could not find an adapter.
Action: The adapter could not be found by the MAC driver.
Check I/O base settings and retry the operation.
5004 OcTk3201 : Could not connect to the interrupt number
supplied.
Action: The interrupt is already used by another device.
Change the adapter interrupt number and retry the operation.
5005 OcTk3201 : Has encountered an internal error and has failed.
Action: An internal error has been discovered. Contact your
place of purchase.
5006 OcTk3201 : The version number is incorrect for this driver.
Action: The driver version is incorrect. Contact your place
of purchase.
5007 OcTk3201 : Timed out during an operation.
Action: A time-out error occurred. Contact your place of
purchase.
5008 OcTk3201 : Has encountered an invalid network address.
Action: An invalid network address was specified. Change the
locally administered network address and restart your system.
The driver uses the burned-in address when loading.
5009 OcTk3201 : Does not support the configuration supplied.
Action: An invalid configuration entry was discovered. Use
the network control panel to set proper adapter parameters.
5010 OcTk3201 : The adapter has returned an invalid value to the
driver.
Action: An internal error has occurred. Contact your place of
purchase.
5011 OcTk3201 : A required parameter is missing from the registry.
Action: A parameter necessary for operation has been omitted
in the registry. Use the network control panel to set proper
parameters.
5012 OcTk3201 : The IO Base Address supplied does not match the
jumpers on the adapter.
Action: The adapter could not be found by the MAC driver.
Check I/O base settings and retry the operation.
5014 OcTk3201 : The adapter is disabled. The driver cannot open the
adapter.
Action: Make sure the startup parameter for the Olicom Token
Ring adapter driver is set to "Manual". Use the "Devices"
applet in the control panel to change the settings.
5015 OcTk3201 : There is an I/O port conflict.
Action: The ports used by the MAC driver is already in use
by another device. Change the I/O Base address for the
adapter.
5016 OcTk3201 : There is an I/O port or DMA channel conflict.
Action: Check the I/O port and DMA usage by the adapter to
ensure that there is no resource conflicts.
5017 OcTk3201 : There is a memory conflict at address xx.
Action: The MAC driver and another device could not share the
memory.
5018 OcTk3201 : There is a interrupt conflict at interrupt number
xx.
Action: Change the interrupt selection on the adapter and
retry the operation.
5019 OcTk3201 : There is a resource conflict at DMA channel xx.
Action: Change the DMA channel selection on the adapter and
retry the operation.
If you experience any problems, you should write down the "Event ID",
"Source", "Description" and "Data" fields in the "Event Detail"
window.