home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
OS/2 Shareware BBS: 36 Tips
/
36-Tips.zip
/
osin1s5t.txt
< prev
next >
Wrap
Text File
|
1996-12-21
|
4KB
|
95 lines
OSIN1S5T - OS/2 WARP 4 INSTALLATION TRAP000D AT IBM1S506$
10/24/96
=======================================================================
OS/2 Warp 4 Installation Trap000d at IBM1S506$
=======================================================================
Please Read Entire Document for Full Explanation of Procedures
--------------------------------------------------------------
DESCRIPTION
A trap000d at IBM1S506$ or a lock up occurs loading IBMIDECD.FLT or
IBM1S506.ADD during startup of OS/2 Warp 4.
RESOLUTION
Use either of the following workarounds:
Modify the BASEDEV=IBM1S506.ADD statement in CONFIG.SYS:
1. Restart the system, pressing Alt-F1 when the small white rectangle
appears in the upper left corner of the screen.
2. Press F2 to go to command line.
3. Type TEDIT CONFIG.SYS, then press Enter.
4. Press Esc.
5. Change BASEDEV=IBM1S506.ADD to BASEDEV=IBM1S506.ADD /a:0 /bm.
6. Save and exit the file, then restart the system.
Replace the driver causing the problem with the corresponding
OS/2 Warp 3 driver:
Note: If you do not have OS/2 Warp 3, download WARPINST.EXE from the
IBM PC Company BBS at 919-517-0001, or from the following web
site:
http://www.pc.ibm.com.
Copy the WARPINST.EXE file into a temporary directory. Change to
that temporary directory and type WARPINST, then press Enter
to extract the files.
1. If the system stops with no error message, identify the driver
causing the problem as follows:
Restart the system, pressing Alt-F2 when the small white rectangle
appears in the upper left hand corner of the screen. This causes the
drivers being loaded to display on screen. The driver remaining on
screen when the lock up occurs is the problem driver.
2. Restart the system, with the OS/2 Warp 4 Installation Diskette in
drive A:. Insert Diskettes 1 and 2 when prompted. Press F3 at the
Welcome screen to escape to a command prompt.
3. Make a backup copy of the problem driver. For example, type:
COPY C:\OS2\BOOT\IBM1S506.ADD C:\OS2\BOOT\IBM1S506.BAK,
then press Enter (where C: is the OS/2 installation drive).
4. Copy the older version of the problem driver to the \OS2\BOOT
directory. For example, type:
COPY X:\TEMP\IBM1S506.ADD C:\OS2\BOOT\IBM1S506.ADD then press Enter
(where X:\TEMP is the path to the older version of the driver files).
5. Remove any diskettes, then restart the system.
Note: Replacing the driver on Diskette 1, along with adding the
correct parameters to the device driver statement in the
CONFIG.SYS file on Diskette 1, will allow the installation to get
past the error. If this procedure is followed,
SET COPYFROMFLOPPY=1
must also added to the bottom of the CONFIG.SYS file on
Diskette 1.
warp4
______________________________________________________________________
IBM disclaims all warranties, whether express or implied, including
without limitation, warranties of fitness and merchantability with
respect to the information in this document. By furnishing this
document, IBM grants no licenses to any related patents or copyrights.
Copyright (c) 1994, 1995 IBM Corporation. Any trademarks and product
or brand names referenced in this document are the property of their
respective owners. Consult your product manuals for complete trademark
information.