home *** CD-ROM | disk | FTP | other *** search
/ OS/2 Shareware BBS: 4 Drivers / 04-Drivers.zip / 594p.zip / RELNOTES.DOC < prev    next >
Text File  |  1995-01-16  |  3KB  |  90 lines

  1.  
  2.               DigiWARE Release Notes   93000098P
  3.                     for
  4.     DigiCHANNEL PC/X*, COM/Xi, MC/Xi, Xem, C/X, EPC/X and AccelePort 
  5.              Universal OS/2 Device Driver
  6.                   
  7.                   XALL.SYS  V1.4.8
  8.  
  9.         Microsoft OS/2          1.0, 1.1, 1.2, 1.21, 1.3
  10.         IBM OS/2                1.0, 1.1, 1.2, 1.3, 2.0, 2.1
  11.         IBM OS/2 Ext. Edition   1.1, 1.2, 1.3, 2.0
  12.  
  13.         Diskettes               P/N's 40000593P (5) or 40000594P (3)
  14.         Diskettes               P/N's 40000943  (5) or 40000908  (3)
  15.         Software Manual         P/N 92000100C
  16.  
  17.         cxbios.bin  V6.4    fxbios.bin  V2.2    sxbios.bin  V2.2
  18.         cxcon.bin   V6.4    fxcon.bin   V2.2    sxfep.bin   V2.2
  19.         cxfep.bin   V6.4    fxfep.bin   V2.2    mxfep.bin   V1.4 
  20.         xxbios.bin  V4.0    xxfep.bin   V7.06
  21.  
  22.  
  23.                    01/15/95
  24.  
  25.  
  26.     Below are Enhancements and Bug fixes made to XALL.SYS V 1.4.7
  27.     resulting in the new XALL driver V 1.4.8
  28.  
  29.  
  30.     1) Enhancements
  31.  
  32.        - Support has been added to the driver for the EPC/X. See INSTALL.
  33.          DOC for installation directions.
  34.        - Command line parameter "/a:q" now turns off quick writes.
  35.          (See Manual Errata below and INSTALL.DOC)
  36.        - DMODE.EXE now runs in an OS/2 window.
  37.        - DMODE.EXE now supports "quick write" mode. (See Manual Errata
  38.          below and INSTALL.DOC)
  39.        - Upgraded to xxfep.bin V7.06 and xxbios V4.0.
  40.  
  41.     2) Bug Fixes
  42.  
  43.        - Fixed more mysterious hangs at boot time which could be seen on
  44.          Pentium and PCI bus computers.
  45.        - Set TX Low water mark to TxMax-1 instead of TxMax. This fixed
  46.          unreported bug where threads blocking for transmit room would
  47.          wake up immediately.
  48.        - Fixed bug that could cause DosClose to take several seconds.
  49.        - Fixed bug that could cause loss of transmit data on close using
  50.          C/X and EPC/X products.
  51.        - Changed default read and write timeouts from 1 second to 1
  52.          minute to match IBM COM.SYS driver.
  53.        - Fixed bug that would keep CTRL-BREAK from terminating application
  54.          threads in DosRead and DosWrite calls.
  55.        - Fixed bug that could cause IOCTl Fucntion 68h (Query RX queue
  56.          count) to return too large a count.
  57.  
  58.     3) Known Limitations
  59.  
  60.       - Maximum 256 channels.
  61.       - The COM/Xi is limited to 9600 or at most 19200 baud.  The Xem
  62.         and AccelePort will support 115k  and 230k on at least 16
  63.         ports respectively. The EPC/X will support 115k on at least 16
  64.         ports. All other intelligent cards will support 38.4K baud on
  65.         all channels, and 57K baud on a few channels.
  66.  
  67.     4) Manual Errata
  68.  
  69.       - The EPC/X board must be specified with a "/t:c" parameter
  70.         on the "device=" line in the config.sys file. (See INSTALL.DOC)
  71.  
  72.       - The meaning of the "/a:q" command-line parameter has been changed.
  73.         Originally, this parameter enabled the driver's quick-write mode.
  74.         However, the use of this parameter did nothing, since the driver
  75.         defaulted to quick-write mode and there was no means by which to
  76.         disable it. With this release of the driver, the "/a:q" command
  77.         line parameter DISABLES quick-write mode. If you are currently
  78.         using this parameter, please review the quick-write discussion
  79.         in INSTALL.DOC.
  80.  
  81.       - DMODE.EXE has been enhanced to permit quick-writes to be enabled
  82.         or disabled on a port by port basis. The new DMODE parameters are
  83.         QW=ON and QW=OFF. For a discussion of quick-writes, please see
  84.         INSTALL.DOC.
  85.  
  86.  
  87.  
  88.  
  89.  
  90.