home *** CD-ROM | disk | FTP | other *** search
/ The World of Computer Software / World_Of_Computer_Software-02-385-Vol-1of3.iso / m / mcademo2.zip / README.TXT < prev    next >
Text File  |  1990-12-11  |  4KB  |  92 lines

  1. Restoring your system after you are done with this working model
  2. ================================================================
  3. After you are done using the working models, you can remove
  4. the working model files from your hard disk.  To do this, follow
  5. these steps:
  6.  
  7. 1. On your hard disk, locate your version of Microsoft Windows.  
  8.    If you know you have the full version of Windows 3.0, skip 
  9.    to step #3.  If you know you have a demonstration version of 
  10.    Windows 3.0, skip to step #2.  If you are not sure which 
  11.    version of Windows 3.0 you are running, run WINVER from your 
  12.    Windows directory.  Winver will report the version of Windows
  13.    it finds in the directory.  If it says "Windows Version 3.00"
  14.    or something very similar, you have the full version of 
  15.    Windows 3.0.  If it says something like "Windows working model" 
  16.    or "Windows application enabler", you have a demonstration 
  17.    version of Windows.
  18.  
  19. 2. Follow this step only if you have a demonstration version 
  20.    of Windows, and no longer want to use it.  Change directories 
  21.    to your Windows directory (probably C:\WINDEMO).  Type DEL *.*, 
  22.    and then type Y at the "Are you sure?" prompt.  Change directories 
  23.    to the SYSTEM subdirectory and type DEL *.* again.  This procedure
  24.    will remove all the Windows files.
  25.  
  26. 3. To remove a particular working model, change directories to
  27.    your Windows directory (probably C:\WINDOWS or C:\WINDEMO).
  28.    Look for the subdirectory containing the working model you
  29.    want to delete.  Delete any such directories.  Then type
  30.    DEL ENABLER.* in your Windows directory.
  31.  
  32. 4. To restore your CONFIG.SYS file to its original condition,
  33.    see the following section.
  34.  
  35.  
  36. Restoring your CONFIG.SYS file
  37. ==============================
  38. In order to set up your computer to work with Windows 3.0 based
  39. working models, the Setup program has modified your CONFIG.SYS 
  40. file by adding the HIMEM.SYS device driver.  HIMEM.SYS is an 
  41. extended memory driver, and other extended memory drivers may 
  42. conflict with it.  Some programs you own may require these other 
  43. memory drivers.  If this is the case, when you are done using the 
  44. working model(s), you can restore your CONFIG.SYS file to its original 
  45. condition as follows:
  46.  
  47. 1. On your boot drive (most likely C:), change to the root directory.
  48.    Then type DIR CONFIG.*  If Setup changed your CONFIG.SYS file, 
  49.    you should see CONFIG.SYS and a backup file (most likely CONFIG.OLD).
  50.  
  51. 2. To make sure the backup file is the version you want to restore,
  52.    type TYPE CONFIG.OLD to display the contents of the file.
  53.  
  54. 3. If it is the correct version, type COPY CONFIG.OLD CONFIG.SYS.
  55.  
  56. 4. Reboot your computer by pressing the CTRL, ALT, and DEL keys
  57.    at the same time.
  58.  
  59.  
  60. Running this demo with a LAN Manager 2.0 network
  61. ================================================
  62. If you are running LAN Manager 2.0 or Novell networks with the 
  63. netpopup service running and you do not already have Windows 3.0 
  64. installed, you may have problems running the demonstration version 
  65. of Windows 3.0 included in this package.  To correct this, turn 
  66. off the netpopup service.  
  67.  
  68. To do this with a LAN Manager 2.0 network, type the following
  69. from DOS:
  70.  
  71.     NET PAUSE NETPOPUP
  72.  
  73. To do this with a Novell network, type the following from DOS:
  74.  
  75.     CASTOFF ALL
  76.  
  77. Running this demo with Windows installed on the system
  78. ======================================================
  79.  
  80. Should you have already a retail copy of Windows installed on
  81. your system, the following has to be done in order to avoid
  82. any damage to the previous Windows files:
  83.  
  84. - rename the file WINVER.EXE to any other name (e.g. WINVER.XXX)
  85.  
  86. Supported DOS versions
  87. ======================
  88.  
  89. As is the case with the full retail product, DOS 3.1 or
  90. higher is required in order to run this demonstration version
  91. of Windows.
  92.