home *** CD-ROM | disk | FTP | other *** search
/ Media Share 9 / MEDIASHARE_09.ISO / hamradio / kenwood1.zip / TM721A.MOD < prev    next >
Text File  |  1988-08-29  |  5KB  |  128 lines

  1.  
  2.  
  3.                 KENWOOD TM-721A REPEATER CROSS-BAND INFORMATION
  4.  
  5.  
  6.  
  7.  
  8. MODIFICATION PROCEDURE
  9.  
  10.  
  11. To operate the TM-721A in the repeater cross-band mode, chip resistor
  12. R121 on the Control unit (X53-3130-XX) (B/3) must be removed. The
  13. following modification will detail how to access the resistor.
  14.  
  15. 1.   Disconnect the power supply and the antenna from the transceiver.
  16.  
  17. 2.   Remove the top and bottom covers (12 screws). Do not damage the
  18.      speaker wires when removing the top cover.
  19.  
  20. 3.   Remove the silver colored screws from the front panel chassis (2
  21.      on each side, 1 on top, and 1 on the bottom).
  22.  
  23. 4.   Carefully pull the front panel away from the body of the
  24.      transceiver (do not disconnect any cables).
  25.  
  26. 5.   Locate chip resistor R121 on the Control unit inside the front
  27.      panel. Unsolder and remove the resistor.
  28.  
  29.                                  NOTE
  30.  
  31.      Read the time-out timer paragraph before you perform step 6.
  32.  
  33. 6.   Assemble the transceiver by reversing steps 1 - 4.
  34.  
  35.  
  36.  
  37.  
  38. TIME-OUT TIMER
  39.  
  40.  
  41. The TM-721A provides a built-in 3 minute time-out timer. This
  42. automatically places the transceiver in the receive mode after 3
  43. minutes of continuous transmit. This function can be defeated by
  44. removing chip resistor R122 on the Control unit inside the front
  45. panel.
  46.  
  47.  
  48.  
  49. OPERATING PROCEDURES
  50.  
  51.  
  52. Repeater cross-band operation allows the TM-721A to receive on one
  53. band and re-transmit the signal on the other band. An incoming signal
  54. will automatically be switched to the sub-band. The TM-721A will then
  55. retransmit the signal from the main band. Each band may contain offset
  56. and sub-audible tone information (the optional TSU-6 is required for
  57. decode). The encode and decode tones for a single band must be the
  58. same. Of course, the encoder or decoder may be individually shut off by
  59. using the [TONE] and [CTCSS] keys. In addition, each band may contain
  60. a separate sub-audible tone.
  61.  
  62.  
  63.                               PAGE 1 OF 2
  64.  
  65.  
  66.  
  67.  
  68.  
  69.  
  70. 1.   Select the first frequency in the main band. If required, select
  71.      the offset.
  72.  
  73. 2.   Select the tone if needed. Selecting a tone will not turn on the
  74.      encode or decode functions. To turn on the encoder, press the
  75.      TONE key (the [T] indicator will light in the main display). The
  76.      decoder will be turned on in the next step.
  77.  
  78. 3.   Press the BAND key to move the contents of the main display to
  79.      the sub-display. The decoder can now be turned on by pressing the
  80.      F key and then the CTCSS key (the [CTCSS] indicator will light in
  81.      the sub-display).
  82.  
  83. 4.   Now select the second frequency in the main band. Follow steps 1
  84.      - 3 as needed to select the offset and tone information.
  85.  
  86. 5.   Adjust the main and sub-band squelch controls to the threshold
  87.      point. The TM-721A will transmit in the repeater cross-band mode
  88.      if the squelch controls are set too low or a signal is received.
  89.  
  90.  
  91.                                  NOTE
  92.  
  93.   The next two steps place the unit in the repeater cross-band mode.
  94.  
  95.  
  96. 6.   Press the F key.
  97.  
  98. 7.   Press the A.B.C. key within 5 seconds of pressing the F key.
  99.      Three dots will be lit in the main display. The unit will now
  100.      operate as described previously.
  101.  
  102.  
  103.  
  104.  ___________________________________________________________________
  105. /                                                                   \
  106. |                                                                    |
  107. |                                                                    |
  108. |                                                                    |
  109. |                                                                    |
  110. |                                                                    |
  111. |                                                        CONNECTOR   |
  112. |                                                    _______________/
  113. |                            CN 102                 /   ____________
  114. |                    LITH    _______                |  |            |
  115. |                    BATT   |       |               |  |            |
  116. |               R121        |_______|               |  |            |
  117. |               x           x R122                  |  |            |
  118. \___----____________________________________________/  |____________|
  119.  
  120.  
  121.  
  122.  
  123.  
  124.  
  125.  
  126.  
  127.                               PAGE 2 OF 2  
  128.