CD-Recorder Manufacturers

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Note: This information is provided without any warranty and may not be complete. All names may be trademarks or registered trademarks of their respective owners. If your CD-Recorder is not listed, you can simply try. If your writer is listed, please check for required firmware.

This list assumes CloneCD Version 2.8.5.2

Back to Hardware Requirements

Supported CD-Recorders "M" (17 April 2001)

• Lifetec / Medion / Tevion
• Memorex
• Mitsubishi
• Mitsumi
• Mustek

Lifetec / Medion /Tevion

Back to Top

Memorex

Back to Top

Mitsubishi

Back to Top

Mitsumi

Back to Top

Mustek

Back to Top

Legend:

Firmware: 

• If nothing is specified, any firmware version will work. However, the newest firmware version available is recommended.
• Rev. >= X.X : Firmware version X.X or better is required
• Rev. = X.X : The exact Firmware version X.X is required. Any other version WILL NOT WORK.

Best Write Mode:

• RAW-DAO 96 = 2352 bytes RAW Data + 96 Bytes P-W Subchannel Data. This is the best mode for CloneCD. It allows writing of all subchannel information, including Digital Signatures, CD-Text, ISRC, Catalog Numbers, CD+G, CD+Midi, Gaps, Indices and Crazy TOCs.
• RAW-DAO 16 = 2352 bytes RAW Data + 16 Bytes P-Q Subchannel Data. This is the second best mode for CloneCD. It allows writing of most subchannel information, including most Digital Signatures, ISRC, Catalog Numbers, Gaps, Indices and Crazy TOCs.
• RAW-SAO = 2352 bytes RAW Data. This is the third best mode for CloneCD. Feature support is drive dependant. ISRC, Catalog Numbers and Indices can be written. Usually CD-Text, CD+G and CD+MIDI can be written as well. Crazy TOCs and Digital Signatures can't be written in this mode.
• SAO = 2352 bytes error corrected Data. This is the worst mode for CloneCD. Writing of ISRC, Catalog Numbers, Indices and usually CD-Text is supported. Not yet implemented, will be supported in CloneCD 3.x
• - = Writing to this drive is not supported. CloneCD will not recognize the drive as a CD-Recorder.

Buffer under run Technology:

• = Drive offers a buffer under run technology like BurnProof or JustLink. This option can be controlled by the user.
• = Drive offers Seamless Link buffer under run technology. Seamless Link is always enabled and can not be switched off.
• = Drive offers a buffer under run technology, but the current CloneCD version does not support this feature yet. It is very likely, that this feature will be supported in the future.
• = Drive offers a buffer under run technology like BurnProof or JustLink, but this option does not work with CloneCD RAW writing and MUST be turned off!
• - = Drive does not offer any buffer under run technology

Correct EFM encoding of regular bit patterns

• = Drive writes regular bit patterns correctly
• - = Drive does not write regular bit patterns correctly

Best Read Mode:

• RAW+96 = 2352 bytes RAW Data + 96 Bytes P-W Subchannel Data. This is the best mode for CloneCD. Reads all subchannel information like ISRC, Catalog Numbers, CD+G, CD+MIDI, Gaps, Indices, Digital Signatures.
• RAW+16 = 2352 bytes RAW Data + 16 Bytes P-Q Subchannel Data. This is the second best mode for CloneCD. Reads most subchannel information like Gaps, Indices and most Digital Signatures.
• RAW = 2352 bytes RAW Data. No Subchannel Data can be read.
• - = Reading from this drive is not supported.

Back to Top