home *** CD-ROM | disk | FTP | other *** search
/ ftp.whtech.com / ftp.whtech.com.tar / ftp.whtech.com / articles / archives / limanews.exe / GKPOWER.TXT < prev    next >
Text File  |  2006-10-19  |  6KB  |  149 lines

  1. ORIGINALLY PUBLISHED IN LIMA NEWSLETTER JUNE 1988
  2.  
  3.     ^^^^^^^@Replacing^the^Gram^Kracker^Lithium^Battery^with^a^NiCad^Battery  
  4.     ^^^^^^^^^^^^^^^^^^^^^^^^^^by Mike Richardson 
  5.     ^^^^^^^^^^^^^^^^^^^^^^^^^Lima Ohio User Group 
  6.  
  7. @NOTE: Proceed at your own risk.  You assume all responsibility for decisions
  8. to modifying a Gram Kracker.  The memory chips (6264) in the Gram Kracker are
  9. sensitive to static electricity and are easily damaged.  If you are not adept
  10. at modifying circuitry, seek help from a users group who may be able to
  11. assist. 
  12.  
  13. The average life of the lithium battery in my Gram Kracker is about 6 months.
  14. After opening it about a half dozen times to replace the battery, the pins
  15. between the two mother boards have become bent.  I decided to install a NiCad
  16. battery in the Gram Kracker.  This article documents the procedure I followed. 
  17.  
  18. @MATERIAL^REQUIRED: 
  19. .LM +5 
  20. 1 Yuasa #3-51 FT-P 3.6 Vdc 50maH NiCad battery with wire leads. 
  21. 1 1N4001 diode 
  22. 1 10 ohm 1/4 watt resistor, SEE NOTE BELOW 
  23. .LM -5 
  24.  
  25. @SOURCE^of^Battery: 
  26. .LM +5 
  27. You may order the battery from All Electronics Corp., P.O. Box 567, Van Nuys,
  28. CA., 91408.  This company has treated me fairly in the past when I was not
  29. satisfied with an order. 
  30.  
  31. Catalog # NCB-3.6PC 
  32. $1.50 each 
  33. 10 for $12.50 
  34. S/H $3.00 per order 
  35. Phone # 1-800-826-5432 
  36.  
  37. .LM -5 
  38.  
  39. @INSTRUCTIONS: 
  40. .LM +5 
  41. 1. Study the schematic and board layout before beginning. 
  42.  
  43. 2. Open the Gram Kracker according to the Operators Manual. 
  44.  
  45. 3. Momentarily place the NiCad battery behind the center switch and between the
  46. two CMOS ram chip banks (6264).  Visually inspect and confirm that the battery
  47. will fit within your version of the Gram Kracker. 
  48.  
  49. DO NOT PROCEED UNLESS YOU ARE CONVINCED THAT THE BATTERY WILL FIT! 
  50.  
  51. 4. Remove the lithium battery. 
  52.  
  53. 5. Observe the polarity markings on the lithium battery holder.  Now carefully
  54. unsolder and remove the holder.  Using an ink pen, mark a small + and - sign
  55. symbol next to the printed circuit (PC) traces that the battery holder went
  56. through. 
  57.  
  58. 6. Using a pair of side cutters, gently cut the top row of leads off the center
  59. switch (Gram 1-2 / TI BASIC).  The top two leads of this switch are not
  60. electrically connected to any circuit on the board.  Now unsolder and remove
  61. the other end of the cut switch wire leads from the board. 
  62.  
  63. 7. Cut one lead of the resistor to 1/2 inch length.  Cut the anode lead of the
  64. diode to 1/2 inch length.  Wrap the cut lead of the resistor around the anode
  65. lead of the diode.  Solder this joint.  Solder a 3 inch piece of Kynar wire
  66. (Radio Shack wire wrap) to the cathode lead of the diode. 
  67.  
  68. 8. Referring to the attached sketch, install the other end of the resistor lead
  69. in the plated thru hole and the cathode lead of the diode in the positive PC
  70. terminal.  Solder both ends on the PC board.  Solder the other end of the Kynar
  71. wire on the diode to the positive terminal of the NiCad battery. 
  72.  
  73. 9. Cut a 3 inch piece of Kynar wire and solder one end to the negative terminal
  74. of the NiCad battery.  Solder the other end of the wire to the PC board hole
  75. where the old lithium battery holder was installed. 
  76.  
  77. 10. Put 2 small pieces of electrical tape on each end of the NiCad battery.
  78. Press fit the NiCad battery in between the two banks of CMOS ram chips (6264). 
  79.  
  80. 11. Double check all your work.  Check to make sure there are no solder or flux
  81. bridges on the board.  Power up the Gram Kracker at @YOUR^OWN^RISK. 
  82.  
  83. 12. Leave the computer on for about 20 hours to fully charge the NiCad battery.
  84. This battery should power the battery backup circuitry for about 4 to 6 weeks
  85. between charges. 
  86.  
  87. Mike Richardson          
  88. 2610 Tenth St. N.W. 
  89. Canton, Ohio 44708 
  90.  
  91. .NA;NF 
  92.            10 ohm 
  93.  
  94. +5 >----\/\/\/\/\----| 
  95.                      | 
  96.                      | 
  97.                   +  |     Anode 
  98.             1N4001 @----- 
  99.                     @--- 
  100.                      @- 
  101.                   @------- 
  102.                      |     Cathode 
  103.                      | 
  104.                      ----------------O 
  105.                      | 
  106.                      |              /|\ 
  107.                      |               | 
  108.                      |               | 
  109.             NiCad @-------         Old battery holder 
  110.             Battery @---           printed circuit 
  111.                   @-------         tracing 
  112.                     @---              | 
  113.                      |              \|/ 
  114.                      |
  115.                      ----------------* 
  116.                      | 
  117.                      | 
  118.                     @--- 
  119.                     @||| 
  120.  
  121. .LM 5;RM 75;AD;FI 
  122. Note: The +5 volts to the resistor is obtained from the plated thru hole on the
  123. GK lower board.  This plated thru hole picks up the +5 volts from the edge
  124. connector #19 on the GK board.  You will need to trace this from this edge
  125. connector to the plated thru hole. 
  126.  
  127. .NA;NF 
  128.  
  129. |~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~| 
  130. |          Lower Board                | 
  131. |          Solder Side                | 
  132. --------------------------------------- 
  133.   | | | | | | | | | | | | | | | | | | 
  134.   | | | | | | | | | | | | | | | | | |  <---bottom board,bottom side 
  135.   0 0 0 0 0 1 1 1 1 1 2 2 2 2 2 3 3 3 
  136.   1 3 5 7 9 1 3 5 7 9 1 3 5 7 9 1 3 5  <---edge connector # 
  137. .LM 5;RM 75;AD;FI 
  138.  
  139. Note: The "Memo Power" NiCad battery apparently has a built in current limiting
  140. resistor.  I am currently using a 10 ohm resistor in the schematic above.  A
  141. digital voltmeter reading of the voltage across the resistor indicates that the
  142. charging current thru the NiCad is about 2ma.  The old GE NiCad Battery
  143. reference book suggest a charge rate between 0.05C and 0.1C.  The 2ma rate
  144. would be 2/50= 0.04C.  Close enough! However, I leave it up to you to choose
  145. the proper resistor value. 
  146.  
  147. If anyone has some manufacture's data on these NiCads, please leave a note. 
  148. .PL 1
  149.