home *** CD-ROM | disk | FTP | other *** search
/ ftp.whtech.com / ftp.whtech.com.tar / ftp.whtech.com / articles / archives / limanews.exe / CLEANCON.TXT < prev    next >
Text File  |  2006-10-19  |  5KB  |  106 lines

  1. ORIGINALLY PUBLISHED IN LIMA NEWSLETTER JANUARY 1987
  2.  
  3.  
  4.  
  5. CHARLIE SAYS:
  6.  
  7.                    CONSOLE CLEANING:
  8.            A SOLUTION TO MANY CONSOLE PROBLEMS 
  9.  
  10.     Do modules (particularly EXTENDED BASIC) refuse to
  11. work when inserted into your console? Does your
  12. EXTENDED BASIC frequently crash while in use? Do some
  13. of the keybard keys fail to respond every now and then?
  14. All of these problems are usually caused by dirty
  15. connections within the console, not by bad modules.
  16. Taking the console apart and cleaning the places where
  17. things plug together will do away with all of the above
  18. problems.  I know from first hand experience. 
  19.  
  20. Cleaning the inside connections of the console is a job
  21. any idiot can do successfully.  There are three major
  22. components inside, the power supply, the main circuit
  23. board, and the keyboard.  These all easily unplug from
  24. one another once the screws holding them to the plastic
  25. console enclosure are removed.  The only tools needed
  26. to clean the inside of the console are a phillips
  27. screwdriver, some isopropyl (rubbing) alcohol, a few
  28. cotton swabs, and a cereal box.  No soldering is
  29. required.   
  30.  
  31. --  Turn the console upside down and remove the 7
  32. screws.  Gently separate the bottom from the rest of
  33. the console.  With a little wiggle, the on/off switch
  34. will fall out.  
  35. --  Revove the two corner screws that hold the power
  36. suppply in place.  This is the green circuit board.
  37. Gently remove the power supply and unplug it from the
  38. main circuit board (the one with the metal covering). 
  39. With some alcohol and a swab scrub the exposed pins of
  40. this plug that are on the green circuit board. 
  41. --  Remove the three screws (two corner and one
  42. recessed inside a hole in the metal cover) holding the
  43. main circuit board in place.  Unless you have a good
  44. reason to, leave the metal cover (the heat sink)
  45. attached.   
  46. --  Revove the 4 screws that hold the keyboard to the
  47. console housing.  Lift the main circuit board and the
  48. keboard from the computer.  Then unplug the keyboard
  49. from the main circuit board.  Use a swab and alcohol to
  50. scrub (yes, really work at scrubbing them) the pins to
  51. this plug on the main circuit board.  This cleaning
  52. should solve any irregular keyboard problems you may
  53. have had. 
  54. -- Remove the "L" shaped grom extender from the main
  55. circuit board.  This is the thing that modules plug
  56. into.  It may now be in the console housing instead of
  57. th circuit board.  Cut a piece of a cerial box so it is
  58. just wide enough to fit into the connector in the main
  59. circuit board where the "L" shaped grom extender was.
  60. Dip this cardboard in some alcohol. Insert it into the
  61. grom extender plug in the main circuit board and move
  62. it in and out as well as sideways to clean this
  63. connector. 
  64. --  Using your fingers lift up both ends of the plastic
  65. end of the "L" shaped grom extender.  This plastic
  66. piece is located where modules plug into the computer
  67. an has a felt pad inside.  Throw the plastic piece
  68. and its felt pad away, or revove the felt pad and
  69. replace the plastic without the pad.  This pad coats
  70. modles with accumulated dirt each time a module is
  71. inserted into the computer.  Use alcohol and a swab to
  72. scrub (really scrub hard) both sides of the flat
  73. connectrs on the grom extender that plug into the main
  74. circuit board.  Then use cardboard soaked in alcohol to
  75. throughly scrub the place where modules are inserted. 
  76. --  Reassemble the console.  Connect the keyboard to
  77. the main circuit board and lay these in the upside down
  78. top of the console.  Screw in the keyboard and then the
  79. main circuit board.  Connect the power supply, lay it
  80. in position and screw it in.  Route the power input
  81. jack to its proper position in the back of the console
  82. and then screw on the bottom of the console.  Finally
  83. push in the loose external on/off switch.  It should
  84. pop right in. 
  85.  
  86.     The entire procedure outlined above takes about
  87. 15-20 minutes, less if you are more experienced. You
  88. may be amazed at the improvement in performance.  Your
  89. EXTENDED BASIC should now load first time every time. 
  90.  
  91.     This may be a good time to consider replacing the
  92. black & silver console power supply with a "switching
  93. power supply".  These switching supplies run MUCH
  94. cooler than the original since they only deliver power
  95. output when it is required.  At other times they do not
  96. deliver unwanted heat producing power.  Switching power
  97. supplies were used by TI in the later model grey
  98. consoles and work fine as exact replacements in silver
  99. consoles.  Some RADIO SHACK stores have them in stock
  100. (part #277-1016) for $4.95 and they are also advertised
  101. in the Computer Shopper for about the same price.
  102.  
  103.     The Lima User Group will have a demonstration of
  104. console disassembly and cleaning in our February 87
  105. meetng.  Be there!!
  106.