home *** CD-ROM | disk | FTP | other *** search
/ Monster Media 1993 #1 / MONSTER.ISO / cad / dgadihdg.doc < prev    next >
Encoding:
Text File  |  1993-05-05  |  18.5 KB  |  422 lines
  1. ========================================================================
  2. DGADIHDG.DOC
  3. The document file for Protected mode ADI driver(DGADIHDG.EXP / Ver 3.1)
  4. ========================================================================
  5.  
  6. The file DGADIHDG.EXP is Protected mode ADI driver(ADI 4.2) that allows a 
  7. Hitachi tablet listed below to interface with AutoDesk programs such as 
  8. AutoCAD, AutoShade, or any other AutoDesk application software that can 
  9. use a Protected-mode ADI digitizer.
  10.        HDG-1111C
  11.        HDG-1212D
  12.        HDG-1212E
  13.        HDG-1217D
  14.        HDG-1515D
  15.        HDG-1717D
  16.        HDG-2222/2222S/2222T
  17.        HDG-2436/2436S/2436T
  18.        HDG-3648/3648S/3648T
  19.        HDG-4460/4460S/4460T
  20.  
  21. To install the DGADIHDG driver, you need to set the functions of Tablet by
  22. DIP swiches or Menu sheets.
  23.  
  24. 1. For HDG-1111C with Pen/4-B cursor
  25.           DSW1 - 1, 3 and 4 ; ON
  26.           DSW2 - 3 and 5    ; ON
  27.           DSW3 - All        ; OFF
  28.           If 12-B cursor is used, DSW3-4 must be ON.
  29.    (Note) The HDG-1111C will be set as;
  30.           0.025mm, REMOTE mode, Lower-left origin,
  31.           9600bps, 7-data, Even parity, 1-stop
  32.           ASCII format(Hitachi)
  33.  
  34. 2. For HDG-1212D, 1515D, 1717D and 1217D
  35.           DSW1 - all  ; OFF
  36.    (Note) The D-series tablet will be set as;
  37.           0.025mm, REMOTE mode, Lower-left origin,
  38.           9600bps, 7-data, Even parity, 1-stop
  39.           ASCII format(Hitachi)
  40.           
  41. 3. For HDG-2222 - HDG-4460 with DP004 I/F board
  42.           MODE/RATE(DIP switch)   - all  ; OFF
  43.           BAUDRATE(DIP switch)    - 8    ; ON
  44.           Jumper pin on the board - 1S and ASYNC(2) ; ON
  45.    (Note) The large tablets with I/F board(DP004) will be set as;
  46.           0.025mm, REMOTE mode, Lower-left origin,
  47.           9600bps, 7-data, Even parity, 1-stop
  48.           ASCII fotmat(Hitachi)
  49.  
  50. 4. For HDG-2222S - HDG-4460S with DP401 I/F board
  51.           DSW1 - all     ; OFF
  52.           DSW2 - 2 and 4 ; ON
  53.           DSW3 - 1 and 2 ; ON
  54.    (Note) The large tablets with I/F board(DP401) will be set as;
  55.           0.025mm, REMOTE mode, Lower-left origin,
  56.           9600bps, 7-data, Even parity, 1-stop
  57.           ASCII fotmat(Hitachi)
  58.  
  59. 5. For HDG-2222T - HDG-4460T
  60.           HITACHI-1 Default
  61.    (Note) The T-series large tablet will be set as;
  62.           0.001", RUN mode, Lower-left origin,
  63.           9600bps, 7-data, Even parity, 1-stop,
  64.           ASCII format(Hitachi)
  65.  
  66. 6. For HDG-1212E
  67.           HITACHI Default
  68.    (Note) The HDG-1212E will be set as;
  69.           0.025mm, REMOTE mode, Lower-left origin,
  70.           9600bps, 7-data, Even parity, 1-stop
  71.           ASCII format(Hitachi)
  72.  
  73.  
  74.  
  75. ===========================
  76. NOTE for INSTALLING DRIVER
  77. ===========================
  78. The Hitachi Protected mode ADI driver(DGADIHDG.EXP) can be used with
  79. AutoCAD R11 and R12. But you have to set the different environment
  80. for R11 and R12.
  81.  
  82.  
  83.  
  84. 1. Installing the Protected mode ADI driver under AutoCAD R11
  85. ==============================================================
  86.  
  87. After copying the DGADIHDG.EXP from "Hitachi drivers" diskette to
  88. the AutoCAD root directory(ex;C:\acadr11), type the following to install
  89. Protected mode ADI driver at DOS prompt.
  90.  
  91.       set DGPADI=C:\ACADR11\DGADIHDG
  92.  
  93. You should add the environment variable DGPADI into the startup batch.file
  94. (ex;acad386) so that the driver is loaded whenever you start the AutoCAD R11.
  95.  
  96.  
  97. For example, follow the step listed below to install and use Protected
  98. mode driver under AutoCAD R11.
  99.  
  100. (1). Insert "Hitachi drivers" diskette into drive A:.
  101.  
  102. (2). Copy the Protected mode ADI driver from the diskette to your AutoCAD R11
  103.      root directory(ex; C:\ACADR11).
  104.  
  105.          COPY  A:DGADIHDG.EXP  C:\ACADR11
  106.  
  107. (3). Enter the following command at DOS prompt.
  108.  
  109.          SET DGPADI=C:\ACADR11\DGADIHDG
  110.  
  111.      (Note) Add this line to AutoCAD R11 startup batch file(acad386.bat),
  112.             if you want to set automatically.
  113.  
  114. (4). Type acad386 to run AutoCAD R11.
  115.  
  116. (5). Choose "5. Configure AutoCAD" on the main menu.
  117.  
  118. (6). You will see Current AutoCAD Configuration.
  119.      Press Enter key to continue.
  120.  
  121. (7). Choose "4. Configure digitizer" on the Configuration menu.
  122.  
  123. (8). Enter "y" to select a different digitizer.
  124.  
  125. (9). Choose "2. ADIP386 digitizer" on the available digitizers list.
  126.  
  127. (10). Choose the digitizer model you are using from the Supported models
  128.       list.
  129.          ------------------------------------------
  130.         |   Supported models;                      |
  131.         |                                          |
  132.         |     1. HDG-1111C                         |
  133.         |     2. HDG-1212D                         |
  134.         |     3. HDG-1212E                         |
  135.         |     4. HDG-1217D                         |
  136.         |     5. HDG-1515D                         |
  137.         |     6. HDG-1717D                         |
  138.         |     7. HDG-2222/2222S/2222T              |
  139.         |     8. HDG-2436/2436S/2436T              |
  140.         |     9. HDG-3648/3648S/3648T              |
  141.         |    10. HDG-4460/4460S/4460T              |
  142.         |                                          |
  143.         |   Enter selection, 1 to 10 <1>:          |
  144.          ------------------------------------------
  145.  
  146. (11) Choose the pick button.
  147.      If you use 12-B cursor or 16-B cursor, you can choose the pick button.
  148.          -------------------------------------------------------------------
  149.         |   Which button do you want to assign as PICK for 12-button cursor |
  150.         |   or 16-button cursor ?                                           |
  151.         |   (Note) If you use 2-button or 4-button cursor, the pick button  |
  152.         |          can not be assigned.                                     |
  153.         |     "0" button (Same function as HICOMSCAN driver)                |
  154.         |     "1" button                                                    |
  155.         |                                                                   |
  156.         |   Enter your selection, 0 or 1 <1>;;                              |
  157.          -------------------------------------------------------------------
  158.      
  159.       (Note) If you use Pen or 4-button cursor, the pick button will be
  160.              Tip-switch for Pen or Yellow button for 4-button cursor
  161.              regardless the above selection.
  162.  
  163. (12). Enter the number of buttons on your cursor.
  164.          ------------------------------------------------------------
  165.         |   The digitizer can have the following types of cursor:    |
  166.         |                                                            |
  167.         |     2 buttons                                              |
  168.         |     4 buttons                                              |
  169.         |     12 buttons                                             |
  170.         |                                                            |
  171.         |   Enter the number of buttons on your cursor <2>:          |
  172.          ------------------------------------------------------------
  173.  
  174.       (Note) If you selected HDG-1212E or Large tablet(HDG-2222/2222S/2222T to
  175.              HDG-4460/4460S/4460T), you will see the "16 buttons" in this
  176.              menu.
  177.  
  178. (13). Enter the port name you want to use.
  179.          ------------------------------------------------------------
  180.         |   Connects to Asynchronous Communications Adapter port.    |
  181.         |   Standard ports are:                                      |
  182.         |                                                            |
  183.         |     COM1                                                   |
  184.         |     COM2                                                   |
  185.         |                                                            |
  186.         |   Enter port name, or address in hexadecimal <COM1>:       |
  187.          ------------------------------------------------------------
  188.  
  189. (14). Press "0" to exit to Main Menu.
  190.  
  191. (15). Enter "y" to keep Configuration changes.
  192.  
  193. (16). Select "1.Begin a NEW drawing" or "2.Edit an EXISTING drawing"
  194.       to start AutoCAD.
  195.  
  196.  
  197.  
  198.  
  199. 2. Installing the Protected mode ADI driver under AutoCAD R12
  200. =============================================================
  201.  
  202. After copying the DGADIHDG.EXP from "Hitachi Driver" diskette to
  203. the AutoCAD R12 drivers directory(ex;C:\acadr12\drv), type AutoCAD startup
  204. batch file(ex;acadr12) to install Protected mode ADI driver and to run
  205. AutoCAD R12.
  206.  
  207. (Note)
  208. The installation program of AutoCAD R12 will make a startup batch file
  209. (ex;acadr12.bat) to set the environment for the protected mode ADI driver.
  210. You will see the following line in the batch file.
  211.  
  212.       set ACADDRV=C:\ACADR12\DRV
  213.  
  214. You should copy the DGADIHDG.EXP to C:\ACADR12\DRV directory.
  215.  
  216.  
  217. For example, follow the step listed below to install and use Protected
  218. mode driver under AutoCAD R12.
  219.  
  220. (1). Insert "Hitachi Driver" diskette into drive A:.
  221.  
  222. (2). Copy the Protected mode ADI driver from the diskette to your AutoCAD R12
  223.      drivers directory(ex; C:\ACADR12\DRV).
  224.  
  225.          COPY  A:DGADIHDG.EXP  C:\ACADR12\DRV
  226.  
  227. (3). Enter "acadr12"(AutoCAD R12 startup batch file) at DOS prompt.
  228.      You will see the drawing editor screen of AutoCAD R12.
  229.  
  230. (4). Choose "Configure" from the File menu or enter CONFIG at the command
  231.      prompt.
  232.  
  233. (5). You will see Current AutoCAD Configuration.
  234.      Press Enter key to continue.
  235.  
  236. (6). Choose "4. Configure digitizer" on the Configuration menu.
  237.  
  238. (7). Enter "y" to select a different digitizer.
  239.  
  240. (8). Choose "6. Hitachi Protected mod ADI driver" on the available
  241.      digitizers list.
  242.  
  243. (9). Choose the digitizer model you are using from the Supported models
  244.       list.
  245.          ------------------------------------------
  246.         |   Supported models;                      |
  247.         |                                          |
  248.         |     1. HDG-1111C                         |
  249.         |     2. HDG-1212D                         |
  250.         |     3. HDG-1212E                         |
  251.         |     4. HDG-1217D                         |
  252.         |     5. HDG-1515D                         |
  253.         |     6. HDG-1717D                         |
  254.         |     7. HDG-2222/2222S/2222T              |
  255.         |     8. HDG-2436/2436S/2436T              |
  256.         |     9. HDG-3648/3648S/3648T              |
  257.         |    10. HDG-4460/4460S/4460T              |
  258.         |                                          |
  259.         |   Enter selection, 1 to 10 <1>:          |
  260.          ------------------------------------------
  261.  
  262. (10) Choose the pick button.
  263.      If you use 12-B cursor or 16-B cursor, you can choose the pick button.
  264.          -------------------------------------------------------------------
  265.         |   Which button do you want to assign as PICK for 12-button cursor |
  266.         |   or 16-button cursor ?                                           |
  267.         |   (Note) If you use 2-button or 4-button cursor, the pick button  |
  268.         |          can not be assigned.                                     |
  269.         |     "0" button (Same function as HICOMSCAN driver)                |
  270.         |     "1" button                                                    |
  271.         |                                                                   |
  272.         |   Enter your selection, 0 or 1 <1>;;                              |
  273.          -------------------------------------------------------------------
  274.      
  275.       (Note) If you use Pen or 4-button cursor, the pick button will be
  276.              Tip-switch for Pen or Yellow button for 4-button cursor
  277.              regardless the above selection.
  278.  
  279. (11). Enter the number of buttons on your cursor.
  280.          ------------------------------------------------------------
  281.         |   The digitizer can have the following types of cursor:    |
  282.         |                                                            |
  283.         |     2 buttons                                              |
  284.         |     4 buttons                                              |
  285.         |     12 buttons                                             |
  286.         |                                                            |
  287.         |   Enter the number of buttons on your cursor <2>:          |
  288.          ------------------------------------------------------------
  289.  
  290.       (Note) If you selected HDG-1212E or Large tablet(HDG-2222/2222S/2222T to
  291.              HDG-4460/4460S/4460T), you will see the "16 buttons" in this
  292.              menu.
  293.  
  294.  
  295. (12). Enter the port name you want to use.
  296.          ------------------------------------------------------------
  297.         |   Connects to Asynchronous Communications Adapter port.    |
  298.         |   Standard ports are:                                      |
  299.         |                                                            |
  300.         |     COM1                                                   |
  301.         |     COM2                                                   |
  302.         |                                                            |
  303.         |   Enter port name, or address in hexadecimal <COM1>:       |
  304.          ------------------------------------------------------------
  305.  
  306. (13). Press "0" to exit to drawing editor screen.
  307.  
  308. (14). Enter "y" to keep Configuration changes.
  309.  
  310. (15). You will see the drawing editor screen.
  311.  
  312.  
  313.  
  314.  
  315. 3. Pointing Device Button Definitions 
  316. ======================================
  317.  
  318. The following lists the digitizer button functions that are executed when
  319. using the DGADIHDG.EXP driver with Standard configuration(i.e., unmodified 
  320. acad.mnu file) of AutoCAD.
  321. This button mapping may be modified by editing the acad.mnu file. 
  322. For instructions to modify the acad.mnu file, refer to the AutoCAD 
  323. "Reference Manual" supplied with your AutoCAD.
  324.  
  325.                     Button              AutoCAD Function
  326.  
  327. Stylus Pen          Tip switch          Pick
  328.                     Barrel Switch       Carriage Return
  329.  
  330. 4-button cursor     Yellow              Pick
  331.                     White               Carriage Return
  332.                     Blue                Displays Pull-down Menu #1(Tools)
  333.                     Green               Cancel
  334.  
  335. 12-button cursor (If you select "1" button as PICK.)
  336.                     1                   Pick
  337.                     2                   Carriage Return
  338.                     3                   Displays Pull-down Menu #1(Tools)
  339.                     4                   Cancel
  340.                     5                   Snap On/Off
  341.                     6                   Ortho On/Off
  342.                     7                   Grid On/Off
  343.                     8                   Coordinate display On/Off
  344.                     9                   Isoplane On/Off
  345.                     *                   Tablet On/Off
  346.                     0                   Not defined
  347.                     #                   Not defined
  348.  
  349. 12-button cursor (If you selecte "0" button as PICK.)    
  350.                     1                   Carriage Return
  351.                     2                   Displays Pull-down Menu #1(Tools)
  352.                     3                   Cancel
  353.                     4                   Snap On/Off
  354.                     5                   Ortho On/Off
  355.                     6                   Grid On/Off
  356.                     7                   Coordinate display On/Off
  357.                     8                   Isoplane On/Off
  358.                     9                   Tablet On/Off
  359.                     *                   Not defined
  360.                     0                   Pick
  361.                     #                   Not defined
  362.  
  363.  
  364. 16-button cursor for HDG-1212E(If you selecte "1" button as PICK.)       
  365.                     1                   Pick
  366.                     2                   Carriage Return
  367.                     3                   Displays Pull-down Menu #1(Tools)
  368.                     4                   Cancel
  369.                     5                   Snap On/Off
  370.                     6                   Ortho On/Off
  371.                     7                   Grid On/Off
  372.                     8                   Coordinate display On/Off
  373.                     9                   Isoplane On/Off
  374.                     A                   Tablet On/Off
  375.                     0                   Not defined
  376.                     B,C,D,E and F       Not defined
  377.  
  378. 16-button cursor for Large tablets(If you selecte "1" button as PICK.)  
  379.                     1                   Pick
  380.                     2                   Carriage Return
  381.                     3                   Displays Pull-down Menu #1(Tools)
  382.                     4                   Cancel
  383.                     5                   Snap On/Off
  384.                     6                   Ortho On/Off
  385.                     7                   Grid On/Off
  386.                     8                   Coordinate display On/Off
  387.                     9                   Isoplane On/Off
  388.                     *                   Tablet On/Off
  389.                     0                   Not defined
  390.                     #,A,B,C and D       Not defined
  391.  
  392. 16-button cursor for HDG-1212E(If you selecte "0" button as PICK.)    
  393.                     1                   Carriage Return
  394.                     2                   Displays Pull-down Menu #1(Tools)
  395.                     3                   Cancel
  396.                     4                   Snap On/Off
  397.                     5                   Ortho On/Off
  398.                     6                   Grid On/Off
  399.                     7                   Coordinate display On/Off
  400.                     8                   Isoplane On/Off
  401.                     9                   Tablet On/Off
  402.                     A                   Not defined
  403.                     0                   Pick
  404.                     B,C,D,E and F       Not defined
  405.  
  406. 16-button cursor for Large tablets(If you selecte "0" button as PICK.)    
  407.                     1                   Carriage Return
  408.                     2                   Displays Pull-down Menu #1(Tools)
  409.                     3                   Cancel
  410.                     4                   Snap On/Off
  411.                     5                   Ortho On/Off
  412.                     6                   Grid On/Off
  413.                     7                   Coordinate display On/Off
  414.                     8                   Isoplane On/Off
  415.                     9                   Tablet On/Off
  416.                     *                   Not defined
  417.                     0                   Pick
  418.                     #,A,B,C and D       Not defined
  419.  
  420.  
  421. (Trademark)
  422. ADI, AutoCAD and AutoShade are trademarks of Autodesk,Inc.