home *** CD-ROM | disk | FTP | other *** search
- ==Phrack Inc.==
-
- Volume Three, Issue 28, File #5 of 12
-
- /////////////////////\\\\\\\\\\\\\\\\\\\\\
- || ||
- || A Real Functioning PEARL BOX Schematic ||
- || ||
- || Written, Tested, and Used ||
- || ||
- || by Dispater ||
- || ||
- || July 1, 1989 ||
- || ||
- \\\\\\\\\\\\\\\\\\\\\/////////////////////
-
-
- Introduction: After reading the earlier renditions of schematics for the Pearl
- Box, I decided that there was an easier and cheaper way of doing
- the same thing with an IC and parts you probably have just
- laying around the house.
-
-
- What Is A Pearl Box and Why Do I Want One?
-
- A Pearl Box is a tone generating device that is used to make a wide range
- of single tones. Therefore, it would be very easy to modify this basic
- design to make a Blue Box by making 2 Pearl Boxes and joining them
- together in some fashion.
-
- A Pearl Box can be used to create any tone you wish that other boxes may
- not. It also has a tone sweep option that can be used for numerous things
- like detecting different types of phone tapping devices.
-
-
- Parts List:
-
- CD4049 RCA integrated circuit
- .1 uF disk capacitor
- 1 uF 16V electrolitic capacitor
- 1K resistor
- 10M resistor
- 1meg pot
- 1N914 diode
- Some SPST momentary push-button switches
- 1 SPDT toggle switch
- 9 Volt battery & clip
- and miscellaneous stuff you should have laying around the house.
-
-
- State-of-the-Art-Text Schematic:
- + 16V 1uF -
- _______________________________||_____
- | ! ! || | _
- | _______________________ |__________| |/| 8ohms
- ____|__|_____:__|__:__|_ | __________| | |
- | 9 10 11 12 13 14 15 16 | | | |_|\|
- | CD4049UBE | | |
- |_1__2__3__4__5__6__7__8_| : | _
- | | |__| |__| | |____________________|_________[-]
- | | ! ! : [b]
- | |__________________________| [a]
- | : : | [t]
- | ! 1N914 ! ! [t]
- |___________|/|_____________________________________[+]
- : |\| : :
- | | |
- | 10M | |
- |___/\/\/\__| |
- | | |
- |_____||____| | <-- These 2 wires to the center pole
- || | | of switch.
- .1uF 50V | |
- | |
- _______________________| |_____________________________
- | ___[Toggle Switch]____________ |
- | | | ___ |
- | | | o o |
- | | | /\/\/\___| |__|
- |_/\/\/\____/\/\/\ | | ^ |
- 1K ^ | |____| ___ |
- |___| | o o |
- | /\/\/\___| |__|
- (pot side) (push-button | ^
- side) |__|
-
- Explanation:
-
- The 2 wires that lead from the main part of the circuit should be
- connected to the center poles on the toggle switch. Put the 2 wires to
- the pot on one side and the 2 wires going to the push-buttons to the other
- side. That way you can switch between tone sweep and the favorite tones
- you like (the push-button side).
-
- To keep tones that you want to use frequently like 1850 Hz then all you
- have to do is put in a variable resistor and adjust it to where you have
- the correct tone, then just put a push-button switch on the line. You can
- link them together in a chain, etc. There are many other good
- modifications to make to the box so have fun and be smart.
-
- --Dispater
-
- \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\?///////////////////////////////////////
-
- Downloaded From P-80 International Information Systems 304-744-2253 12yrs+
-