home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
Hacker Chronicles 1
/
HACKER1.ISO
/
phrk3
/
phrack28.5
< prev
next >
Wrap
Text File
|
1992-09-26
|
5KB
|
106 lines
==Phrack Inc.==
Volume Three, Issue 28, File #5 of 12
/////////////////////\\\\\\\\\\\\\\\\\\\\\
|| ||
|| A Real Functioning PEARL BOX Schematic ||
|| ||
|| Written, Tested, and Used ||
|| ||
|| by Dispater ||
|| ||
|| July 1, 1989 ||
|| ||
\\\\\\\\\\\\\\\\\\\\\/////////////////////
Introduction: After reading the earlier renditions of schematics for the Pearl
Box, I decided that there was an easier and cheaper way of doing
the same thing with an IC and parts you probably have just
laying around the house.
What Is A Pearl Box and Why Do I Want One?
A Pearl Box is a tone generating device that is used to make a wide range
of single tones. Therefore, it would be very easy to modify this basic
design to make a Blue Box by making 2 Pearl Boxes and joining them
together in some fashion.
A Pearl Box can be used to create any tone you wish that other boxes may
not. It also has a tone sweep option that can be used for numerous things
like detecting different types of phone tapping devices.
Parts List:
CD4049 RCA integrated circuit
.1 uF disk capacitor
1 uF 16V electrolitic capacitor
1K resistor
10M resistor
1meg pot
1N914 diode
Some SPST momentary push-button switches
1 SPDT toggle switch
9 Volt battery & clip
and miscellaneous stuff you should have laying around the house.
State-of-the-Art-Text Schematic:
+ 16V 1uF -
_______________________________||_____
| ! ! || | _
| _______________________ |__________| |/| 8ohms
____|__|_____:__|__:__|_ | __________| | |
| 9 10 11 12 13 14 15 16 | | | |_|\|
| CD4049UBE | | |
|_1__2__3__4__5__6__7__8_| : | _
| | |__| |__| | |____________________|_________[-]
| | ! ! : [b]
| |__________________________| [a]
| : : | [t]
| ! 1N914 ! ! [t]
|___________|/|_____________________________________[+]
: |\| : :
| | |
| 10M | |
|___/\/\/\__| |
| | |
|_____||____| | <-- These 2 wires to the center pole
|| | | of switch.
.1uF 50V | |
| |
_______________________| |_____________________________
| ___[Toggle Switch]____________ |
| | | ___ |
| | | o o |
| | | /\/\/\___| |__|
|_/\/\/\____/\/\/\ | | ^ |
1K ^ | |____| ___ |
|___| | o o |
| /\/\/\___| |__|
(pot side) (push-button | ^
side) |__|
Explanation:
The 2 wires that lead from the main part of the circuit should be
connected to the center poles on the toggle switch. Put the 2 wires to
the pot on one side and the 2 wires going to the push-buttons to the other
side. That way you can switch between tone sweep and the favorite tones
you like (the push-button side).
To keep tones that you want to use frequently like 1850 Hz then all you
have to do is put in a variable resistor and adjust it to where you have
the correct tone, then just put a push-button switch on the line. You can
link them together in a chain, etc. There are many other good
modifications to make to the box so have fun and be smart.
--Dispater
\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\?///////////////////////////////////////
Downloaded From P-80 International Information Systems 304-744-2253 12yrs+