Fresh Fish 8/FreshFishVol8-CD1.bin/useful/comm/tcp/amitcp-demo/doc/netfs.doc

Text File | 1994-03-21 | 7KB | 207 lines

               NetFS -- network file system for AmiTCP
               ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

                           by Timo Rossi


                      Version 0.56 (19-Mar-94)


   NetFS is a network filesystem for Amigas running the AmiTCP protocol stack.

Requirements:
~~~~~~~~~~~~~
 · AmigaOS 2.04 or later (AmiTCP requires it anyway)

 · AmiTCP version 3.0 or later.

 · Some sort of network interface that has a Sana2 driver and works
   with AmiTCP (Ethernet, ArcNet, SLIP, CSLIP, PLIP or something other).


Installation instructions:
~~~~~~~~~~~~~~~~~~~~~~~~~~

 · Make sure that you have AmiTCP configured properly and it can communicate
   between the machines you want to use with NetFS (you can use
   the ping-command for checking this)

 · Copy netfs-handler to AmiTCP:L-directory on client machine
   (In earlier versions of NetFS the system L:-directory was used.
    Also, an alternate directory can be specified in the mountlist
    or using the HANDLER-keyword in the netmount-command)

 · Copy netfs-server to AmiTCP:serv-directory on server machine

 · Copy netmount to some directory that is in your path (AmiTCP:bin
   is a good place)

 · Add the following line to the AmiTCP:db/services on all machines
   that will use NetFS (both client and server):

amiganetfs    2500/tcp

   You may select another port number if the default 2500 conflicts with
   something (port 2500 is not officially registered for NetFS)

   If you already have AmiTCP running and don't want to reboot the machine,
   you should send the RESET-command to the AmiTCP AREXX-port to get it
   to re-read the configuration file.

   (You can also use the AmiTCP AREXX port to add the service entry without
    editing the netdb file. See AmiTCP documentation for details)

·  Add the following line to the AmiTCP:db/inetd.conf

amiganetfs stream    tcp nowait root amitcp:serv/netfs-server

   If you have put netfs-server in some other directory than amitcp:bin,
   you should use that directory name here instead.

   If you already have AmiTCP running and don't want to reboot the machine,
   you should send a Ctrl-F signal to inetd with the break-command.

·  Use the netmount-command to mount the partitions you want.
   The command syntax is:

netmount hostname remotedev localdev

  For example, if you want to mount drive dh0: on a machine called Amiga1
  and you want to call the local device rh0:, you can use the following:

netmount Amiga1 dh0 rh0

  The full command template for netmount is:

SERVER=HOST/A,REMOTEDEV/A,LOCALDEV/A,HANDLER/K,NOACT/S:

  If you have put netfs-handler in some other directory than L: or renamed
  it, you can specify its filename with the HANDLER keyword.

  Normally netmount automatically activates the mounted device (the same
  way as 'Mount=1' keyword in mountlist). If you don't want that to
  happen, you can use the NOACT-switch. In that case the device process
  starts when the device is first referenced.


MountLists (optional):
~~~~~~~~~~~~~~~~~~~~~~
  Alternatively you can make the mountlist entries and use the normal mount-
  command. You can put these in the normal DEVS:MountList file or a separate
  file and use the Mount FROM-option. If you have AmigaDOS 2.1 or newer,
  you can also use the new style mountfiles instead of mountlists.

  Here is an example mountlist entry:

RH0:
    Handler = L:netfs-handler
    Priority = 5
    StackSize = 5000
    GlobVec = -1
    Mount = 1
    Startup = Server-machine.name.domain/Device-DH0:
#

   The only parameters that you need to change are the server machine name
   and the device name (The syntax is a little strange for compatibility with
   different versions of the Mount-command. Most of them don't like '='-signs
   on the startup-line)

   If you use the 2.1+ mountfiles, you don't need the device name in the beginning
   or the '#' in the end.


   (But it is so much easier to use the netmount-command, that you probably
   don't want to use mountlists)


Security (or the lack of it):
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
   Netfs has a couple of primitive security features.

    · You can prevent mounting a partition by putting a file called '.nomount'
      in the root directory of that partition.

    · You can cause a partition to be mounted in read-only mode by putting
      a file called '.readonly' in the root directory of that partition.

  You cannot control which machines may connect to the server, so it might
  not be a good idea to connect a machine with netfs-server to the
  global Internet (of course you can use a strange port number
  and hope that nobody guesses it (security through obscurity)).

  It is likely that future versions of netfs have more advances security/
  access control features.


Volume names:
~~~~~~~~~~~~~
   Netfs normally automatically uses the remote volume name in the mounted
   device, but if there is a name collision (another volume/device/assign
   of the same name already exists), it modifies the name by adding
   an underscore and a number to it.

   You can relabel the mounted volume, but this does not affect the actual
   disk on the server machine.


Workbench:
~~~~~~~~~~
   Netfs does not allow access (or Open(), anyway) to a file called '.backdrop',
   so left out icons do not work over the network. This is a feature, not a bug.


Reconnect:
~~~~~~~~~~
   If the server machine is rebooted, NetFS will automatically reconnect
   to it when it is running again. However, there may be long timeouts
   after a connection failure before NetFS gives up. This is a normal
   for the TCP protocol that NetFS uses for its connections.

   Sometimes NetFS may lose the connection to the server machine so that
   it doesn't automatically try to reconnect. In that case, you can
   try to reconnect by using the DiskChange-command.

   You can also force NetFS to close the connection by sending ACTION_DIE
   packet to it (for example with the 'die'-command that comes with MSH).


Known problems:
~~~~~~~~~~~~~~~
   - speed/performance is not the best possible

   - does not support all 2.0 packet types
     (does not support notification or file locking, but does support links)

   - because netfs uses one TCP connection and separate server/client processes
     for each mounted device, memory usage is probably more than actually
     necessary if netfs was implemented in some other, smarter way...

Copyright and distribution:
~~~~~~~~~~~~~~~~~~~~~~~~~~~
   NetFS is Copyright © 1993 by Timo Rossi. It can be freely distributed
   for non-commercial purposes. It can be included on disk collections such
   as Fred Fish's AmigaLibDisks or CD-ROMs such as the AmiNET CD-ROM.

   It may not be used for military purposes or life-critical purposes such
   as controlling nuclear reactors or guidance system for a manned spacecraft.

   If you want to include netfs in a commercial product, you should contact
   me first (my address is in the next section).

   NetFS is NOT under the GNU General Public Licence.
            ~~~
   Source code is not currently available, but it may be in the future...


Contact information:
~~~~~~~~~~~~~~~~~~~~
   Timo Rossi
   Mattilankatu 40 A 4
   40600 Jyväskylä
   FINLAND

   E-Mail:  [e-mail]