# This is the file where Groups stores a backup of your groups list:
backup:<Wimp$ScrapDir>.OldGroups
# This is a scrap file Groups uses for sending ArcWeb requests and
# for monitoring the re-sorting of the groups list.
scrap:<Wimp$ScrapDir>.GroupScrap
# Do not change anything below this line.
# Interactive help messages
message:This is a message from Groups.
message2:Click here to acknowledge the message and close the window.
main:This is the main Groups window.
main2:This shows the current source for the list below.
main4:Click here to change the source used for the list below.
main5:Click here to catch up on new groups.
main6:This shows the number of groups in the main list.
main7:This icon allows you to bring up standard interactive help.
feed:This section shows all the groups you are currently receiving.|MDouble-click on an entry to remove it from your newsfeed.
config:This window allows you to configure Groups.
config2:Select this icon if you do not have a newsgroups file.
config4:Enter the filename of a full newsgroups list.
config8:Enter the date you wish to see new group information from.|mThis must be in the yymmdd format (year month day).
config10:Enter the time you wish to see new group information from.|mThis must be in the hhmmss format (hour minutes seconds).
config13:Click here to set the pointer back to the dawn of time (1980) so that you are shown all new groups on record.
config18:When this is selected, you will be asked for confirmation before adding groups.
config19:When this is selected, you will be asked for confirmation before removing groups.
config20:When this is selected, new group information will be merged into your main newsgroups file when you "Catch up".
config21:When this is selected, Groups will use a vertical display format, with one list above the other.
config15:Click here to close this window without saving any changes.
config14:Click here to save this new information.
info:This window displays information about Groups.
info7:This displays the version number, and should be quoted in any correspondence.
info8:This is the author's Internet e-mail addess.
find:This window allows you to search for specific newsgroups.|mUse the up and down arrows to navigate.
find1:When this box is ticked, you may press RETURN to add the group that has been found.
waiting:This window displays the current status of Groups during lengthy operations.
question:This is a question from Groups.
question2:Click here to answer "Yes".
question3:Click here to answer "No".
source:This section displays a newsgroup list. Use the menu icon above to choose which list to show.|MDouble-click on an entry to add to your newsfeed.
wcard:This window allows you to perform wildcard searches on the newsgroups list. Use an asterisk for a wildcard.
wcard3:Click here to initiate the search.
# Error messages reported during startup
nomem:There is not enough free memory to load the newsgroups file - Groups will still run, but you will be unable to view the full list.
listgone:The newsgroups file that has been configured does not exist. Please re-configure Groups.
nb-old:Groups needs Newsbase version 0.54 or greater to run.
nbgone:Newsbase is not present!
code:Groups cannot load its code file - is the file missing?
nongfile:The configured newsgroups file could not be found.
# Error messages reported during execution
timefmt:The time must be specified in the NNTP convention of hhmmss.
datefmt:The date must be specified in the NNTP convention of yymmdd.
nomatch:No newsgroups found
comms9:%1 (Command invalid error %0)
comms2:%1 (Newsbase busy error %0)
comms1:%1 (Command failure error %0)
rxdied:Data transfer failed: Receiver died.
badpattern:You must specify the pattern to search for.
sortfailed:Resorting failed (%0)
nomemsort:No memory was available to run the sort program.
badhelp:No help could be found for this window. Please report to author.
howtosave:To save, drag the icon to a directory display.
noscrap:You must save to a directory rather than an application.
# Status messages
g-loading:Groups is loading - please wait.
g-full:Loading your newsgroups file.
g-newsbase:Waiting for Newsbase to be loaded.
g-new:Retrieving new groups list.
g-feed:Retrieving subscribed groups.
g-merge:Merging newsgroups file.
# Confirmation messages
c-remgrp:Are you sure you want to remove group %0?
c-addgrp:Are you sure you want to add group %0?
# General messages
welcome:Welcome to Groups version %0. If you have a full newsgroups file, please configure it now in the Configure window.
source1:Newsgroups file
source2:New groups
source3:Search results
num1:%0 groups
num2:%0 new groups
num3:%0 found
nonew:No new newsgroups
nosub:No groups subscribed
# URL format for CTRL-dragging groups/ArcWeb requests (%0 is group name)
url:news://%0/
# Pesticide
rep:An unexpected error has occurred. Please report the error "%0" to the author.