Black Box 4

home *** CD-ROM | disk | FTP | other *** search

/ Black Box 4 / BlackBox.cdr / genapps / perf.arj / PERFECT.DOC < prev next >

Wrap

Text File | 1989-12-15 | 51KB | 1,016 lines

* PERFECT BOX * Loudspeaker Enclosure Simulation using the Neville Thiele - Richard Small Model Version 4.5 January 1, 1990 Warren A. Merkel 2851 Newcomb Ct. Orlando, FL 32826 Program registration is required. See final page of this document for details. ***** PERFECT BOX ***** Version 4.5 ****** * Program and documentation written by * * Warren A. Merkel * ****************************************** I. INTRODUCTION: PERFECT BOX is a Computer Aided Design (CAD) program for the simulation of loudspeaker performance. PERFECT BOX is a very powerful tool for the amateur or professional speaker builder. Loudspeaker design is a balance of compromises involving enclosure size, low frequency cutoff, and transient response. This program will allow you to model the loudspeaker-enclosure combination entirely on your PC. With proper use, you can be assured of the best (lowest in frequency) bass response in the smallest enclosure. You can then build the enclosure with full confidence that the final result will not become the new dog house for Fido, but an accurate, natural sounding system. PERFECT BOX does not deal with midrange or tweeter drivers. It only considers the low frequency driver in a multi-way system (or the only driver in a full-range system.) Since enclosure alignments, such as box size, box type, and box frequency (now on referred to as Alignments), effect the woofer response, PERFECT BOX models systems covering low frequencies from 10 to 200 Hertz. The mathematical model will hold for higher frequencies, but I have optimized the program for the most useful range. II. REQUIREMENTS: PERFECT BOX requires certain parameters that uniquely define the driver's characteristics. Some of these parameters have been coined as the Thiele/Small (or T/S) parameters. If you are new to loudspeaker design, it isn't important that you understand what each value represents, only that you are able to obtain these values from the driver manufacturer, or measure them yourself (the preferred method.) PARAMETER UNITS Free air resonance (Fs) Hertz Electrical (Qes) Q Mechanical (Qms) Q Total (Qts) Volume Equivalent Compliance(Vas) Ft^3 D.C. Voice Coil Resistance (Re) Ohms Peak Cone Displacement (Xmax) Inch Effective Piston Diameter Inch Thermal Power (P) Watts, RMS PERFECT BOX allows you to store these driver parameters in a data file ("BOXDATA4"). This file can store characteristics for thousands of different drivers. A few sample drivers have been included so that you can experiment with PERFECT BOX. These samples represent "real life" units which are currently available at this time. III. DEFINITIONS: ***SYSTEM ORDER*** PERFECT BOX uses a classical high-pass filter model to simulate a loudspeaker mounted in an enclosure. The order of a loudspeaker system represents the same characteristic roll off as that of an electrical filter. The roll off rate (or slope) is: roll off rate = (6 * system order) dB/frequency octave or roll off rate = (20 * system order) dB/frequency decade. PERFECT BOX can simulate both infinite baffle (sealed box), and vented (ported) systems. Each of these systems have a natural order in which they resemble an electrical high pass circuit. For infinite baffle, order=2, or that is to say that they are of 2nd order. And for vented systems, order=4. It seems that each kind of enclosure has pros and cons associated with them. In general, both systems, if properly aligned, perform with the same low frequency response. In practice, an infinite baffle system is easier to build, and possibly has better transient response. The vented system offers slightly higher efficiency (2.9 dB), and good cone dampening near the vent frequency (but less below Fb.) My preference is for 4th and 6th order systems. The sixth order system involves the use of a 4th order system tuned slightly lower than the 4th order ideal, and an 2nd order active equalizer circuit in the amplifier path. ***SYSTEM CUTOFF FREQUENCY*** This is the frequency at which the system amplitude response is exactly 3.0 dB less than at a mid-band reference frequency (where response is basically flat at 0 dB.) This is a standard point of interest that can be used to compare with another system's low frequency response data. This point on the frequency plot represents the "half-power" amplitude, as compared to the amplitude at a mid-band reference frequency. ***OTHER SYSTEM ORDERS*** As you are probably aware, a Graphic Equalizer can make a tremendous effect on the way your speaker system sounds. The bad news is that an equalizer (EQ) usually doesn't have a control exactly centered on the proper frequency to properly extend low frequency cutoff, and thus will typically make matters worst. PERFECT BOX can incorporate the effects of either a 1st or 2nd order, ACTIVE EQ (that you must build) into the loudspeaker model. The affects of which are easily depicted in the PB Graphic Plots. This mini EQ consists of a simple active high-pass filter, having a low turn-over (cutoff) frequency (typically 20-60 Hz), which actually has a slight boost (peak) in its amplitude response above its cutoff frequency. If the amount of boost and cutoff frequency are suitably chosen, the total system response typically is extended a half-octave or more, while providing infrasonic (rumble) filtering to boot. In 2nd-order EQ's, the boost is controlled by the "D" parameter (D=1/filter Q, for you filter buffs.) Typical values of "D" range from 0.3 to 1.414, giving most to least amount of amplitude boost. A "D" of 0.52 gives approximately 6 dB of boost, a typical starting value. The EQ frequency and the "D" factor should be juggled for the flattest, most extended low frequency response. Use the "EQ2.EXE" program to calculate components to implement the 2nd order EQ. A word of caution. Using large amounts of boost may tax small power amplifiers (less than 50 Watts,RMS) beyond their limits. A properly designed 3, 3.5, 5, or 6th order system will not over tax your amplifier unless you listen to music either : 1. at extremely high SPL levels, 2. with heavy (double fortissimo) organ pedal notes, or 3. use other signal modification equipment such as an extremely low-end boosted Graphic Equalizer (quite stupid!), or Sub-Sonic Synthesizer (Harmonizer.) The EQ can be inserted into the signal path of your system at either a "Preamp-out/Amp-in" loop, or "tape monitor" connection. A simple design for a 2nd order EQ is provided with PERFECT BOX. Type EQ2 at the DOS prompt to execute this option. You must have (at least) a CGA graphics card in order to run EQ2 because the electrical schematic is drawn on the screen after all of the circuit values are calculated. IV. RUNNING PERFECT BOX - PROGRAM EXECUTION: If you have an IBM, Epson or HP LaserJet compatible printer, you can print the graphic plots generated by PERFECT BOX. Perfect Box 4.5 has built-in support for Graphic printing for these printers in CGA and EGA modes. You no longer have to use the DOS GRAPHICS.COM or PERFGRAF.COM included with previous releases of Perfect Box. You might have to set your printer switches to DEFEAT "automatic" Linefeed [LF] after a Carriage Return [CR], (see your printer manual.) I have included a simple batch file called GO.BAT, which will execute Perfect Box for you. You may change this batch file to suit your particular needs. The actual program file is BOX4_5.EXE. You will not have to change the program file name until you receive a future upgrade of PERFECT BOX. Insert the PERFECT BOX program disk into your default disk drive, and type GO <Return>. You should see the PERFECT BOX opening screen. Take the time to read this screen and remember that many, many hundreds of hours of effort have been put into this program. If you use this program more than five times, you must be understanding the purpose so don't forget your obligation to this author! If you see an error message stating "Bad Command or Filename", check to see if you are in the same directory as the PERFECT BOX files. After about 5 seconds, you may press RETURN to continue. If all is well, you should see the following screen. PERFECT BOX - Version 4.5 Current Time: ╔═╣ Boxdata Choices ╠════════════╗ ╔═════════════════════════════╗ ║ ║ ║ Drivers on file : 1573 ║ ║ (B) Browse the database ║ ║ Boxdata path : G:\perfect\ ║ ║ (L) Load a driver by # ║ ║ Graphics mode : EGA ║ ║ (S) Store New Driver data ║ ╚═════════════════════════════╝ ║ (E) Edit the database ║ Quick Mode ║ (B) Boxdata Reports ╔════╩═════════════════╣ Utility ╠═╗ ║ ║ ║ ╚═══════════════════════════╣ (C) Change Boxdata path ║ ║ (P) Sort/Pack Boxdata file ║ ╔════════════════════╗ ║ (A) Append new records ║ ║ REGISTERED TO: ║ ║ (W) Write defaults ║ ║ Trial copy. ║ ║ (D) DOS Shell ║ ║ Your name or ║ ║ (Q) Quit to DOS ║ ║ company name should║ ╚══════════════════════════════════╝ ║ be listed here. ║ ║ ║ ╚════════════════════╝ Use PgUp - PgDn - Home - End - - - <RETURN>= Select - or HotKey Output Menu Each of the menu choices may be executed by either pressing the "key letter" or by using the cursor arrow keys to highlight the choice and then pressing RETURN. If you have a mouse, you can choose by clicking the left button on any of the options BOXDATA CHOICES: (B) Browse. This option will allow you to view the drivers currently in the BOXDATA file. You can move through the list using the arrow, Home, End, Page Up, and Page Down Keys. The end key takes you to the bottom of the list, and Home will return you to the first listing. Use these keys to point the "flashing arrows" at your driver choice. If you have sorted your Boxdata file using the Sort/Pack option, you can press any of the Alpha keys (A-Z) to jump to that corresponding Manufacturer name. If you have a mouse installed, you can move the highlight arrows straight to the driver of interest with the left button. The right button will load the currently selected line. Browse-Choose the driver with the arrow keys and press RETURN. »106 »PR 38 XM 150 »POLYDAX »15",PRO,MONITOR,96dB « 107 PR 38 XT 150 POLYDAX 15",PRO,FOAM EDGE,MONITOR 108 PR 38 XT 250 POLYDAX 15",PRO,99dB 109 PR 38 XT 350 POLYDAX 15",PRO,HI-POWER,100dB 110 TA-305 FSW PRECISION DUAL V.C. SUBWOOFER 111 TA-305F PRECISION OMEGA 112 TD-125F PRECISION ALPHA 113 TD-255F PRECISION EPSILON 114 TD-255F-SW PRECISION 10",Alum Dual VC,90.7dB 115 TO-205F PRECISION INFINITE BAFFLE 8" (** Only ten drivers are listed here for clarity. **) <Esc>=Quit - <F2>=Edit - <F3>=Load defaults. PgUp-PgDn-Home-End - <INS>=Get # < <┘ >= Get Record 106 Perfect Box Browse function. After pointing to a particular driver, you may LOAD the driver parameters by pressing RETURN. You can EDIT the driver parameters by pressing the <F2> function key. The <F3> function key will load any previous Box Volume, Vent Frequency, Order, D factor, and EQ frequency information saved in a previous execution of PERFECT BOX, and initiate the calculation loop. You still can bypass the current selected driver and load any other driver by pressing <INSERT> and entering the record number. The <F3> function key will take you back out to the opening menu. When you return to the BROWSE function, the BOXDATA list will be on the same page as the last time you were there. (L) LOAD: This option allows you to LOAD driver data directly from the BOXDATA file using the record number. On Floppy based systems, this option might save you time by skipping the Browse feature. (S) STORE: This option allows you to enter new driver data into the BOXDATA file. ALL parameters listed are required, so don't skip any unless you are told you may enter a Zero. If you don't have all of the correct T/S parameters, you should try to obtain them from the manufacturer. In a pinch, you can approximate values from other drivers in the BOXDATA file. Don't forget to add the correct values when you get them. Of course, the accuracy of this loudspeaker model is DIRECTLY proportional to the T/S parameter accuracy! Which brings me to say this: I claim no responsibility for the completeness or accuracy of the T/S parameters included with your copy of PERFECT BOX. Many (very many!) of the current drivers listed have been appended from files sent to me by Registered users of PERFECT BOX. If you are unsure of any data, it is your responsibility to verify the T/S parameters with the manufacturer or test them yourself! (Soapbox off.) The new entries are placed at the bottom of the BOXDATA file and once entered, can be LOADED immediately. (E) EDIT: You can edit any of the T/S parameters in the BOXDATA file. Use the current driver record number to call up the driver and follow the screen prompts for instructions. You can also edit a driver directly from the BROWSE function. (B) REPORTS: You can print the full BOXDATA file on your printer in two forms. The first form contains ALL of the driver parameters including comments. The second form will print the driver's basic T/S parameters, Fs, Vas, and Qts, and use them to calculate the "Ideal" 4th order Box volume, Vent frequency, and F3 cutoff point. This form is very handy to compare driver performance. UTILITY (C) Change Boxdata Path: The BOXDATA file containing all driver parameters, can be located on a different drive/directory than the current DOS default. Choose this option if you want to change the path to the data file. Note: The path is saved for future executions of PERFECT BOX using the Write Defaults option. You could use this feature to maintain more than one BOXDATA4 file. (P) Sort/Pack Each new driver that you enter into the BOXDATA file is placed at the bottom of the file. You can use the Sort/Pack option to sort the file alphabetically by Manufacturer. If you have marked a driver for deletion in the EDIT driver menu, the Sort / Pack routine will purge it from the BOXDATA file. This routine is the an updated version of the sort program that was included with earlier versions of PERFECT BOX, and thus (if you have them) you should delete the old BSORT.BAT and BOXSORT3.EXE program files. (A) Append new records This option is used to combine other BOXDATA files into the current, active BOXDATA file. If you are upgrading from Version 3.xx, rename the OLD data file to "DATAUP.DAT". Start PERFECT BOX and choose the Append option. If you are upgrading from Version 2.xx, you must run the 2to4.exe program first. Version 3 uses a slightly different file structure, and thus the 2to4.exe program will convert you old BOXDATA file into the new structure, leaving a new file called "BOXDATA4". Since this is the current name of the Version 4.0 data file, YOU MUST DO THIS CONVERSION IN ANOTHER DIRECTORY THAN THE ONE CONTAINING THE NEW BOXDATA4 FILE INCLUDED IN THE VERSION 4.5 ARCHIVE! Either use a different directory or copy the NEW, original BOXDATA4 to another directory for safe keeping. I suggest that you make backup copies of EVERYTHING, OLD AND NEW, before attempting the conversion process. After running the 2to4.exe program, rename the resulting file from BOXDATA4 to "DATAUP.DAT". Copy "DATAUP.DAT" file into the PERFECT BOX directory, choose the APPEND function, and watch it fly! (W) Write defaults. Each time PERFECT BOX is loaded, a file named PERFECT.CTL is read for startup defaults. There are many default values kept in this file including: 1. Boxdata4 data file directory: 2. Graphics mode: CGA, EGA, or HERC; 3. "Quick mode" toggle; 4. Printer Port assignment, mouse calibration values and other variables. The first two values have obvious purposes. The third parameter is used to hold the default mode for the calculation loop end point. In normal mode, the loop counts up to 200 Hz. In Quick mode, the loop counts up to 100 Hz. This is useful for making quick estimates on the slower "XT" type machines. You can toggle this mode within PERFECT BOX with the <F9> function key. The write defaults option will over-write the configuration file with current values for BOXDATA file path, Graphics and Quick Modes. PERFECT BOX 4.5 uses a different format for this control file than earlier releases. You should delete you old perfect.ctl file and restart PERFECT BOX. (D) DOS Shell You can spawn another copy of COMMAND.COM from within PERFECT BOX using this option. Use this option to check directories or file space. Type EXIT at the DOS prompt to return to PERFECT BOX. This option actually executes a batch file called "SH.BAT". You could modify this batch file to run another program instead of loading Command.com. (Q) Quit to DOS Just like it says! This choice will halt execution of PERFECT BOX and immediately return you to the DOS. OK, OK!, enough talk. Let's see some action! Now that you know what all of that stuff does on the opening menu, choose a driver from the BOXDATA file. Use the BROWSE option, point at an interesting driver, and press RETURN. The parameters listed are the minimum that you will need to know about any driver simulated with PERFECT BOX. For this example, answer "Y" to the question "Do you want this driver?" Now choose "1" for a single driver simulation. Record # ─────────> 106 Manufacturer ─────> POLYDAX Model Number ─────> PR 38 XM 150 Comment ──────────> 15",PRO,MONITOR,96dB Free air resonance= 19.5 hz. Vas = 24.37 ft^3. Qts = .27 Qes = .3 Qms = 2.7 Re = 5.8 Ω Xmax= .1377953 Piston Diameter= 14 in. Power= 150 Watts. DO YOU WANT TO USE THIS DRIVER (Y)? Now, PERFECT BOX will calculate the "Ideal" 4th Order Box volume, the port frequency for that ideal box volume, and the cutoff frequency (-3dB point.) The ideal box volume is the smallest enclosure that provides the flattest, deepest low frequency response. The cutoff point will give you a general idea of how low the driver will perform in any box design (best case.) The port frequency (box frequency) must be set as calculated to obtain the cutoff predicted. In a 4th order system: Ideal vented volume is 8.53 Ft^3. System cut-off (-3dB) is 32.54 Hz. If the Vent frequency is 26.61 Hz. ╔═══════╦═══════════════════════════════════════════════╗ ║ ORDER ║ SYSTEM DESCRIPTION ║ ╠═══════╬═══════════════════════════════════════════════╣ ║ 2. ║ CLOSED BOX─┬─without Active Equalizer ║ ║ 3. ║ ├─with 1st Order Active Equalizer ║ ║ 3.5 ║ └─with 2nd Order Active Equalizer ║ ║ » 4. ║ VENTED BOX─┬─without Active Equalizer ║ ║ 5. ║ ├─with 1st Order Active Equalizer ║ ║ 6. ║ └─with 2nd Order Active Equalizer ║ ╚═══════╩═══════════════════════════════════════════════╝ Efficiency Bandwidth Product..(Fs/Qes).. is 64 , which suggests a 4th order system. Enter System Order [ 4 =default] ? Enter BOX VOLUME (Ft^3) [ 8.53 =default] ? Enter BOX VENT FR. (Hz.) [ 26.61 =default] ? Now you must decide what type of enclosure to use. If the driver has a Qts of 0.5 or greater, I would try infinite baffle (order=2) systems first, otherwise, use Order=4, with the ideal box size and frequency. Save the other Order options for later. Since PERFECT BOX will recommend the Order for you, use it as a default. Press RETURN to accept the default Order. Enter the Box volume in cubic feet. I suggest that you use the ideal box size as a starting point. Then, on the next pass, change one of the box alignments and check how the response was affected. Again, press RETURN to accept the default Box volume, or change it if you prefer to do so. Enter the Vent Frequency in Hertz. Again, since this is your first time through, press RETURN to accept the default value. PERFECT BOX will now calculate : 1. Amplitude response in decibels; 2. Maximum Power in Watts; and 3. Maximum Sound Pressure Level, at each frequency cycle between 10 and 200 Hertz. (100 Hz in Quick mode.) Please wait ... Calculating data for the frequency of xx Hz. Be patient here. PERFECT BOX is running through a healthy chunk of floating point calculations, just sit back, watch the counter change and reminisce about the good old slide rule days. When the calculations are complete, an Output/Changes Menu will be presented. A math coprocessor chip makes this loop fly by in about 2 seconds (if you have one installed!) PERFECT BOX - Version 4.5 ╔═║ Output Choices ╠════════════╗ ╔════════════════════════════════╗ ║ ║ ║ Record # : 106 ║ ║ (F) Frequency vs. Amplitude ║ ║ Driver : PR 38 XM 150 ║ ║ (L) Excursion Limit plot ║ ║ Manufacturer: POLYDAX ║ ║ (V) View data points ║ ╚════════════════════════════════╝ ║ (U) QUAD-Plot Set-Up [ OFF ] ║ ║ (D) Print Data points ║ Quick mode ║ (P) Calculate Ports ╔════════╩══╣ Changes ╠══════════════╗ ║ (W) Driver Worksheet ║ ║ ║ ║ (B) Change Box Volume or Vent freq.║ α=2.857 ╚══════════════════════╣ (E) Change EQ. Frequency or D ║ h=1.365 ║ (A) Change All parameters ║ ║ (T) Toggle graphics mode (EGA) ║ ║ (C) Change QLoss ╔══════════════╩╣ Done╠╗ ║ (Qloss = 7 ) ║ ║ ╚═════════════════════╣ (S) Load/Save Align. ║ ║ (R) Retrieve another ║ ║ (Q) Quit to DOS ║ ║ ║ ╚══════════════════════╝ Use PgUp-PgDn-Home-End- - - <RETURN>= Select - or HotKey Output/Changes Menu OUTPUT CHOICES: (F) Amplitude vs. Frequency Plot This choice will plot the classical Bode (pronounced BO-DEE) or Amplitude Response plot. If the Quick mode was on during calculations, the plot will stop a 100 Hz. You may print a copy of the plot on your graphics printer by pressing a "P". This pops up a nice time-date stamp, dumps the plot to your printer. After the printer is finished, you can send a Form Feed (FF) to your printer by pressing the <F10> function key. (L) Excursion Limit Plot This graph of SPL & Power vs. Frequency, will give you an picture of the system driven at maximum power. This plot gives the Sound Pressure Level (in dB) and the input power required to reach the excursion limit (Xmax) of the driver. See the Design Notes chapter of this document for more discussion of this important graph. (U) QUAD-Plot Setup (New to Version 4.5) ┌────────────┐ │Current Data│ │ in RAM. │ └────────┬───┘ │Trace toggle Model#: Filename: Load Data: └──> F1 On ├──┐ │ F2 Off ├──┼< --- │Empty <─ F6─┐ │ │ Press F1-F4 F3 Off ├──┼< --- │Empty <─ F7─┤ to enable │ │ that trace #. F4 Off ├──┼< --- │Empty <─ F8─┤ │ │ │ │ ┌──────────────┴┐ │From Disk file.│ └───────────────┘ Press F10 to Exit Save driver data in the Output Menu with the F7 key. You may load up to three data files for display in the QUAD Plot mode. QUAD-Plot Setup Menu For EGA users, the QUAD-Plot function will allow you to compare Amplitude Plots from the current run with up to three other runs previously saved from the Output Menu with the F7 option. Once in the QUAD-Plot Setup menu, you load the data files with function keys F6, F7 and F8. The function keys F1-F4 will toggle each trace off and on, allowing printout of fewer traces than the loaded number. Once you have loaded your comparison files, press F10 to return to the Output Menu. You should notice that the prompt beside the QUAD-Plot Setup function should say "[ ON ]" This is automatically set to ON after leaving the QUAD- Plot Setup Menu. You can toggle the QUAD-Plot OFF/ON with the F4 key in the Output Menu. Turning OFF the QUAD-Plot will not erase the currently loaded data, and will allow you to bounce back and forth between the usual plot modes and QUAD-Plot. The QUAD-Plot function is available only in the EGA graphics mode. If your machine cannot support EGA 43 line mode, you cannot use QUAD-Plot. Also, your mouse becomes useful tool during the QUAD-Plot display. Without a mouse, some features will be unavailable to you, but you still can view up to four graphs at once. Perfect Box (4.5) ■ QUAD-Plot | Fb ┌──────────────┬───┬─────────────────────────────────────────────┐ │Registered to:│+6 │ │ │ │ 5 │ │ │Your name or │ 4 │ │ │Company should│ 3 │ │ │be listed │ 2 │ │ │here. │ 1 │ │ │ │ 0─┼──────────────────────────────────── │ │ │-1 │ │ │ │-2 │ │ │ │-3 │ │ │ │-4 │ │ │ │-5 │ │ │ │-6 │ │ │ │-7 │ │ │ │-8 │ │ │ │-9 │ │ │ │-10│ │ │ PERFECT BOX │-11│ │ │ │-12│ │ │ by │-13│ │ │ Warren │-14│ │ │ A. │-15└────────────────────────────────────────── │ │ Merkel │ │ │ │ 20 30 40 50 60 7 8 9 100 200 Hz │ ├──────────────┼───────────────┬──────────┬──────────┬───────────┤ │ │ │ │ │ │ │ │Trace 1 │ Trace 2 │ Trace 3 │ Trace 4 │ │At Magnifier: │ 3124 │ Mod: │ Mod: │ Mod: │ │Amp = │ ALTEC │ Man: │ Man: │ Man: │ │Freq= │ From RAM │ File: │ File: │ File: │ │At Ruler: │ Vb : 2.79 CF │ Vb : │ Vb : │ Vb : │ │Amp = │ Fb : 33.44 Hz│ Fb : │ Fb : │ Fb : │ │Freq= │ Ord : 4 │ Ord : │ Ord : │ Ord : │ │ │ Feq : │ Feq : │ Feq : │ Feq : │ │ │ D : │ D : │ D : │ D : │ │ │ Single │ │ │ │ └──────────────┴───────────────┴──────────┴──────────┴───────────┘ Press P to Print ■ <─┘ to continue The QUAD-Plot Screen (not to scale) Each trace is plotted in a different color and can be temporally erased with function keys F1-F4 or with a left click in the data area for that particular trace. If you have a mouse, you can use the cursor as a magnifier to determine which Trace is where. As you pass over a particular trace, a asterisk will flash beside that Trace's number. You can also set a ruler line at any point on the graph with the left mouse button. This will allow quick measurements of any point on the plot. The ruler will be drawn from the center of the magnifier to each axis, and the values for the ruler will be locked at the "At Ruler" area. To erase the ruler, click the right mouse button. The "At Magnifier" values are constantly updated to the cursor magnifier position. You may have to calibrate your mouse to read the plot correctly. If the magnifier values do not reflect the actual point on the plot, move the magnifier to the words "At Magnifier" and click both buttons. You will be asked to move the magnifier to the 20Hz-0dB point an click the left button. Then you will be asked to move the magnifier to adjust the "At Magnifier" values to reflect exactly 0dB at 20 Hz. Then click left again. Then, if you are satisfied that you correctly positioned the mouse, press the right button to save these new calibrated values in the Perfect.ctl file. You can abort by pressing the right button. As with the other Plot screens in PERFECT BOX, you can press a "P" to print the screen on your graphics printer. The F10 key will cause a Form Feed command to be sent to your printer. At this time, only the Amplitude Plots can be compared. If sufficent user interest dictates the addition of the SPL-Power plots into the QUAD-Plot function, I will work that mode into the next release. (Registered users first though...) (V) View data points This option will list on the screen, all calculated data, between the frequency limits of your choice. (D) Print data points This option will print on your printer, all calculated data, between the frequency limits of your choice. (W) Driver Worksheet This option produces on your printer, a worksheet which gives you a handy reference table to use as you change the different alignments about your system. Each block can be filled from data printed on the Frequency vs. Amplitude plot option. I suggest that you do this option first (only if you have a printer on-line.) and log each repetition of your progress. (B) Change Box Volume or Vent Frequency (E) Change EQ. Frequency or D (A) Change ALL parameters At this point you may choose what parameter to change in an attempt to optimize the frequency plot, or what ever else you are trying to achieve (maximum power for instance.) If you are currently working on a 2nd or 4th order system, the "Change EQUALIZER Frequency or D." choice will not be allowed. Thus if you want to change to an "equalized" order, you must use the "Change ALL Parameters" option. Remember that the previous value for each prompt in the CHANGE menu, there will be the default value (just press RETURN.) (T) Toggle graphics mode This choice toggles you between EGA and CGA modes. This is really not needed anymore. I left it in for those of you whom can't get the build-in graphics dump program to function properly with your printer. You could for example, have the DOS GRAPHICS.COM loaded before PB, and switch to CGA for printing. (C) Change Qloss This option allows you to account for box leakage losses. Normal vented cabinets are modeled at Ql=7. If you do not have the means to accurately measure Qloss, then leave Ql=7. (S) Load/Save Alignment This choice allows you to save your current design parameters to the BOXDATA file for future use. This becomes very handy if you want to keep track of your best designs for each driver. (R) Retrieve another driver This choice will dump all calculated data, and return you to the opening menu. (P) Calculate Ports After you are satisfied with the current design parameters, PERFECT BOX will calculate the port lengths required to tune the cabinet to the frequency currently chosen. A column for two identical length ports is also given. Dual ports are useful when the box volume or the MACH speed is too large for a single port. The MACH number is the percent of the speed of sound that will occur at the largest port output. POLYDAX PR 38 XM 150 BOX VOLUME= 8.53 Ft^3 BOX FREQUENCY= 26.61 Hz. ORDER : 4 HEIGHT= 39.72 in. WIDTH= 24.52 in. DEPTH= 15.2 in. VENT LENGTHS FOR TYPICAL INTERNAL DIAMETERS OF PVC PIPE (Inches) DIAMETER LENGTH MACH DUAL VENTS MACH ------- ------ ---- ---------- ---- 1 -.38 1.243 NO ! | -.03 .311 NO! 1.5 -.31 .553 NO ! | .48 .138 2 -.06 .311 NO ! | 1.35 .078 Best 2.5 .37 .199 Use Dual| 2.57 .05 Best 3 .97 .138 O.K. | 4.13 .035 Best 3.5 1.75 .101 O.K. | 6.05 .025 Best 4 2.7 .078 Best | 8.32 .019 Best 4.5 3.83 .061 Best | 10.95 .015 Best 5 5.13 .05 Best | 13.92 .012 Vent Calculations. Stay away from large (speed> 0.2) port MACH speeds as they will cause unmusical whistle noises from the port. Ports that are longer than the box depth, can be curved inside the enclosure with PVC swept elbows. V. DESIGN HINTS: If the ideal box volume is too large to be realistically built, PERFECT BOX will allow you to see just how the loudspeaker performance will suffer, as you down size box volume. It is do to this iterative design process that PERFECT BOX accels other modeling programs. By changing either box volume, port frequency, or in EQ cases, EQ frequency and boost, a "perfect" frequency curve should be obtainable. At this point you can tell how good a driver really is because sometimes one driver will out perform others in half the enclosure volume. The port frequency is set by the area and length of the vent. PERFECT BOX will calculate the port for you, but the length is typically 10% off, so add an half-inch to the calculated value, and measure the box frequency for yourself. The system will not perform as calculated if you miss the port frequency by as little as 1 Hz, so try to hit it as close at possible. Also, after you have reached a final box size, increase the box volume by as much as required to account for volume used by the drivers, bracing, and crossover network. It is much better to error on the high side of Box Volume. I typically add 10% to the final size as a fudge factor. You can always add braces to account for any overage. To find box dimensions from the box volume, take the volume in cubic feet, multiply by 1728 cubic in/ft^3, to get in^3. Then take the cube root (or raise it to the 0.3333334 th power.) Now this number is the width in inches. Multiply the width by 1.62 for the height, and multiply the width by 0.62 for the depth. volume (in^3) = volume (ft^3) * 1728 width (in.) = (volume (in^3) )^0.3333334 height (in.) = width * 1.62 depth (in.) = width * 0.62 NOTE: All dimensions are internal, not external! This will give the box a typical speaker "look" and also set the dimensions up for minimum internal reflections. PERFECT BOX calculates these dimensions for you and prints them in the port length table. VI. COMMAND LINE SWITCHES There are a few command switches which will override the settings in the PERFECT.CTL file. /CGA = Sets graphics mode to CGA. /EGA = Sets graphics mode to EGA. /HERC = Sets graphics mode to Hercules. /LPT1 = Sets the active printer port to LPT1: /LPT2 = Sets the active printer port to LPT2: /LPT3 = Sets the active printer port to LPT3: /QUICK = Runs PB in the fast mode (10-100 Hz). /RESETMOUSE = Clears previous mouse calibrations. /NOMOUSE = Defeats all mouse functions. /PTF = Reroutes all text printing to a file called "Printer.out". All text output is APPENDED to this file. /NOPAPER = Defeats the printer error checking. This might be useful if you are using a "Print-TO-File" TSR to grab output. As it stands now, the Novell "SPOOL" command is supported for LPT1: if your workstation has an active local printer attached. The /NOPAPER option bypasses local printer checking and allows SPOOL to capture LPT1 correctly without a local printer attached to LPT1:. All values affected by the Command line switches except /PTF can be made the current default by the "W" Write Defaults command in the opening menu. NOTE: The /NOTEST switch is no longer supported (or required.) If you have a 8087/80287 coprocessor installed, PB will automatically use it for all Floating Point calculations. If for some reason, you would like to defeat the coprocessor from functioning, set an Environment variable in your CONFIG.SYS file NO87=Coprocessor is Defeated and reboot, before executing Perfect Box. You may also use the DOS "SET" command to create the NO87 variable. VII. REFERENCES: This document and the program PERFECT BOX are only tools for the speaker designer. One must know how to use these tools properly before judging the usefulness of PERFECT BOX. I suggest that you read or subscribe to any of the following publications on the finer art of speaker building. SPEAKER BUILDER MAGAZINE (6 times a year) Edward T. Dell, Jr., Publisher PO Box 494 Peterborough, NH 03458 An excellent publication. Articles vary from the most basic "cookbook" projects, to the exotic mathematical theories used in PERFECT BOX. Electronic projects and crossover designs are covered in depth. Many of the systems discussed are years before the designs hit the market. Articles are written by knowledgeable authors well known in the field, ideas of which have been mimicked by the major Speaker Manufacturers. Now with full color layouts, software and book reviews, Speaker Builder is an absolute must. "The Loudspeaker Design Cookbook" by Vance Dickason Distributed by: Old Colony Sound Lab PO Box 243 Peterborough, NH 03458-0243 Hats Off! to Dickason for handy reference to all design formulas required by the speaker designer. Covers explanations of many types of crossover designs and enclosure systems, including Push- Pull, and Isobaric. "How to Design, Build, & Test Complete Speaker Systems" by David B. Weems Library of Congress #TK9968.W43 Published by: TAB Books Blue Ridge Summit, PA 17214 No. 1064 The perfect starter book in speaker design. Written in a down to earth style, Weems covers the T/S theories with just enough math to get the job done correctly without being overbearing to the beginner. Many complete projects and testing methods are covered. A beginners standard for the past decade! VIII. ERRATA: Your support helps! PERFECT BOX is supported by YOU, the user. Without user support, Shareware such as PERFECT BOX cannot continue to exist! Use this program!, give a copy of PERFECT BOX to your friends (the BBS Archive file is the best way to make sure all the PERFECT BOX files are present.) Above all, don't forget your part in the deal! If you are using PERFECT BOX on a trial basis, that's fine. Determine its usefulness in accurately designing your new speaker system, then REGISTER! The money that you save by building your own system can easily cover the registration fee. If you are using PERFECT BOX in a business or commercial environment, you MUST Register, PERIOD. IF YOU ARE MAKING A COMMERCIAL PROFIT USING PERFECT BOX WITHOUT REGISTRATION, YOU ARE IN VIOLATION OF YOUR SHAREWARE AGREEMENT WITH THIS AUTHOR. Your job is easy with PERFECT BOX in your tool kit. Don't forget who bought you that tool! Many registered users are using PERFECT BOX for professional sound reinforcement or automotive sound applications. If this is true for you, just don't forget the concepts under which shareware functions. Perfect Box can easily pay for itself with ONE SALE. PERFECT BOX is under constant scrutiny for improvement. If you have any ideas for new features/functions, or problems in program operation, send them to me at the address on the next page. Your suggestion could be included in the next revision of PERFECT BOX. By registering your copy, you will be sent (if requested) a disk with the current Version installed in your name. You will also receive a copy of the next MAJOR PERFECT BOX revision, and new BOXDATA file parameters. Registered users can have their current copy updated at any time. Also, Registered users can download the future releases of PERFECT BOX directly from my 24 hour BBS at FIDONET 363/507 (407-281-5522 : 2400-N-8-1), including unlimited "Online support" through BBS E-Mail. If you want to others to share in your BOXDATA resources, please send a COPY of your BOXDATA file on disk (5.25" or 3.5") to me in a U.S. Post Office approved disk envelope (or safe equivalent.) Or, upload your BOXDATA file to my BBS. TO REGISTER: Send $40.00 in U.S. funds (personal checks accepted) to cover registration and return postage. IT'S THAT SIMPLE. The un-registered copy is NOT "crippled" in any way. All PERFECT BOX functions are available on the un-registered program. Please make checks payable to: >>> WARREN A. MERKEL << and send your contribution to: Warren A. Merkel 2851 Newcomb Ct. Orlando, FL 32826 (PERFECT BOX 4.5) *** End of Document *** (PERFECT.DOC)