home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
Battle Arena Toshiden
/
TSD.bin
/
TSD
/
Readme.txt
< prev
next >
Wrap
Text File
|
1996-08-23
|
10KB
|
319 lines
This file contains last minute information about Battle Arena Toshinden.
1. If Player One chooses keyboard as their controller,
Player Two must also use the keyboard.
2. When customizing keyboard functions, the following keys will not be
identified properly on screen:
Insert, Home, Page Up, Page Dn, End, and Delete.
3. The default selections for forward and backward are reversed
for Player One. Player Two is not affected. If you "re-map" these
keys, they will work properly. This also exists in the retail version.
4. EMM386.EXE Version 4.49 or later is required to run this program in DOS.
Contact your local software dealer or Microsoft to obtain the latest
version of this program.
*****************************************************************************
Using a Creative Labs Blaster GamePad
You must have the GamePad Joystick switch set to GAMEPAD to work properly.
Using the Creative Labs 3D Blaster
If you are experiencing problems, contact Creative Labs for updated
drivers, and/or game patches at 1-800-998-1000.
Notes on Network Play
Battle Arena Toshinden is compatible with IPX and NetBios networks.
Notes on Modem Play
If the modems connect, but you are unable to play the game, note the connect
speed reported as CONNECT XXXXX (where XXXXX is the speed reported) when the
modems connect, and set the baud rate to that speed.
If you are experiencing problems playing the game (such as the game stops and
you see the message CONNECTION TIMEOUT), select an INIT string in the SETUP
program to enable RTS/CTS handshaking. Consult your modem manual or modem
manufacturer to obtain the proper INIT string values to enable RTS/CTS.
To optimize modem performance, select an INIT string to disable error
correction and data compression. Consult your modem manual or modem
manufacturer to obtain the proper INIT string values to disable error
correction and data compression.
GENERAL INIT STRING
The following is a general modem initialization string which disables error
correction and data compression on most modems. Only use this string if you
are having difficulties connecting using ATZ, and only if you could not find
your specific modem in the list below. Your modem manual also would have
the correct initialization commands to disable error correction and data
compression. This should be entered in the connection setup.
AT &F S46=0 &K0 &Q0 &D2 &W
SPECIFIC MODEM BRAND INIT STRING
Here is a list of manufacturer specific initialization strings which may help
if you are having trouble connecting using ATZ. These initialization string
disable error correction and data compression and should be entered in the
connection setup.
Boca M1440i (internal):
ATS48=0S37=9S46=136%C0%E0%M0&K0&Q0&R1&C1&D2\G0\N1N0
Boca 14.4k (internal):
AT&C0N0S37=9&K0W0&Q0S36=3S48=128%C0
Boca 14.4 Fax/Modem
AT S46=0 S37=9 N0 &Q0 &D2 &K4
Boca 14.4k (external):
AT &F S0=1 S36=0 &K0 &Q6N0S37=9 &D2
Boca 14.4k:
AT S46=0 S37=9 N0 &Q0 &D2 &K0 %C0
Cardinal 14.4k v.32bis, v.42bis Fax/Modem:
AT &F N0 S37=9 &Q0 &D2 \N1
Digicom Systems (DSI) (softmodem):
AT Z \N0 &D2 &K0 S48=48
Digicom Systems Scout Plus:
ATZ*E0*N3*M0*S0*F0&D2
Gateway Telepath:
AT &F S37=9 %C0 &K0 &Q6 \G0
Gateway Telepath 14.4k:
AT S46=0 S37=9 N0 &Q0 &D2 &K0 %C0
Gateway Telepath I:
AT S0=1 &N6 &K0 &M0
Gateway Telepath II:
AT S0=1 S37=9 %C0 &Q0 &K0
Generic v.32bis 14.4k Fax/Modem:
AT \N0 %C0 B8
Generic 14.4k Fax/Modem:
AT S46=0 S37=9 N0 &Q0 &D2 %C0 \G0 &K0
GVC 14.4k (internal):
AT &F B8 \Q0
Hayes 28.8k V.FAST Modem:
AT &Q6 &K S37=9 N %C0 \N0
Infotel 144I:
AT&Q0 S37=9 N0 &D2
Infotel 14.4:
&F0 \N1 &D2 S37=F8
Intel 14.4k:
AT \N0 %C0 \Q0 B8
Intel 14.4k (internal):
AT Z B8 Q1 \C0 \N1 %C0 \V "H
Microcom AX:
&F \N1 \Q0 &D2
Microcom QX/4232bis:
AT %C0 \N0
Netcomm M7F:
AT &E &K0 B0 \V0 X4 &D2 \N1 \Q0 #J0 #Q9 %C0
Nokia ECM 4896M Trellis V.32:
AT Z %C0 /N0
Nuvotel IFX 14.4 (internal):
&F \N1 &D2
Practical Peripherals 14400FX v.32bis:
AT Z S46=0 &Q0 &D2
Practical Peripherals 14400FX v.32bis:
AT S46=0 &Q0 &K0 &D2
Supra:
AT &F0 S46=136 %C0
Supra (external):
AT &K &Q &D \N1
Supra 14.4k v.32bis:
AT &F S46=136 &Q0 &D2
Supra 14.4k v.32bis:
AT &K &Q &D \N1
Telepath 14.4k:
AT &F&M0&K0&N6&H0 S0=1
Twincomm DFi 14.4:
AT&F &Q0 %C0 S37=9 &D2
UDS V.3223:
&F \N1 \Q &D2
UDS Fastalk 32BX:
&F0 \N1 &D2
USR Courier v.32bis:
ATS0=1 S7=60 E1 Q0 V1 &C1 &D2 &H0 &K0 &M0 &N6 &A3
USR Courier HST/DS 16.8k:
First reset the modem in a communication program with AT&F&W
AT X4 B0 &A0 &B0 &H2 &I0 &K0 &M0 &N6a
USR DS v.32bis v.42bis (external):
AT&m0&n6&a0&r1&h0&k0&i0&s0&b1x1
USR Sporster 9600:
AT&M0&K0&N6
USR Sportster 14.4k Fax/Modem USING ERROR CORRECTION:
AT S0=1 S7=60 E1 QO V1 &C1 &D2 &K0 &N6 &A3
USR Sportster 14.4k Fax/Modem (internal):
AT &F&M0&K0&N6&H0
USR Sportster 14.4k (internal):
AT &F &B1 &H0 &I0 &K0 &M0 &N6 &R1
USR Sportster 14.4k:
ATS0=1S7=60E1Q0V1&C1&D2&K0&N6&A3
USR Sportster 14.4k:
AT &F0 &K0 &M0 &N6 &H0 &I0 &B1 &R1
USR Sportster 14,000 Fax Modem:
AT S0=2 &N6 &K0 &M0 &I0 &H0 &R1 &A0 V1 X4
USR 14.4k:
AT &F&A0&K0&M0
USR 14.4k
AT &K0 &H0 &D0 &I0 &R1
USR 14.4k Dual Standard
ATB0&R1&B1&N6Q0X4&A0&D2&H0&I0&K0&M0M1
USR (model?):
&F E1 V1 X4 &C1 &D2 &N0
ViVa 14.4k:
AT&F&Q6\N0%C0&D2N0S37=9
ViVa modem (internal):
&F&Q6\N0%C0&D2N0S37=9
Zoltrix model 14/14 VE:
AT S0=Q0 V1 &C1 &D2 W2 &Q0
Zoom 14.4k VFX:
AT&Q6S37=9N0%C\N0
Zoom 14.4k VFX:
AT&Q6S37=11N0%C&K0
Zoom OEM Modem:
AT&Q6S37=9N0&K0
Zyxel U-1496E:
AT Z &N4 &K0
COMMON MODEM COMMANDS
Here are the most common settings and what they do:
&F - This fetches the factory default in most modems. Always a
good starting point. Modems with multiple factory settings
may require a qualifier (i.e. &F0)
S46=0 - This register setting disables compression on many v.32 and v.42
modems. You might also try S46=136 or %C0.
&K0 - Disable flow control between the modem (DCE) and your PC (DTE).
This was one of the most common problems -- You should look
at flow control options more closely if you connect and just hang
WITHOUT the screen clearing and displaying the blue banner. Check
your modem documentation carefully. The command(s) to manipulate
flow control varies quite a bit on various modems. The commands
\G and \G0 were also quite common.
&Q0 - Places the modem in DIRECT mode. This is by far the best method
for pumping data down those wires! At least to start with, stay
away from the error correcting and speed buffering configurations.
The command \N1 is the next most common command to set the modem
in direct mode.
&D2 - DTR handling. DTR is the signal (voltage) on the serial connector
on your PC that says "I'm here". This control helps with initially
talking to the modem and disconnecting. The &D2 in tells the modem
how to handle the loss of the DTR signal from the PC. In this case,
the modem will go into COMMAND MODE from DATA MODE (if not already
there) and send the normal verbose response (i.e. "OK"). Many modems
also support a neat option (&D3) which recalls the prior
configuration.
&W - Write the configuration to the modem's memory. This is optional
but I always like to do this -- just like I always like to use
the factory reset (&F) at the beginning.
IMPORTANT: When you use the &W you permanently change your modem
modem settings. If your other communication programs
do not set your modem each time, you may have to
configure your modem for those other programs again.
S37=F8 - Another very common problem is when 14.4 modems report a connect
of CONNECT 14400. Try to force the modem to 9600 bps.
F8 is hexadecimal notation.