home *** CD-ROM | disk | FTP | other *** search
/ PC-Test Pro / PCTESTPRO.iso / scsi / adaptec / os2 / org / ibmos2.hlp < prev    next >
Encoding:
Text File  |  1995-03-27  |  2.7 KB  |  70 lines

  1.  
  2. DATE:     September 14. 1992
  3.  
  4.  
  5. SUBJECT:  0S/2 v 1.3 Installation Notes
  6.  
  7. Procedure for adding a AHA-1540/1542 to a pre-existing installation of 0S/2 
  8. version 1.3.
  9.  
  10. This installation procedure assumes the following:
  11.  
  12. -- The user has previously correctly installed 0S/2 v 1.3 on a system
  13.    Original installation did not include any Adaptec Host Adapter 
  14.      (e.g. installed on an IDE disk)
  15.    The system currently boots and runs properly
  16.    The user now wishes to add an Adaptee AHA-1540/1542 and SCSI disk drive(s) 
  17.       to the system
  18.  
  19. -- The user does not wish to re-install OS/2 v 1.3 from scratch 
  20.       (i.e. does not want to start over)
  21.    The user has the original OS/2 v 1.3 boot diskette
  22.  
  23. -- The user has the Adaptee ASW-1220/1420 v 1.3 diskette
  24.  
  25. If the above statements are all true, then please proceed as follows:
  26.   
  27.    Boot the system and get to an OS/2 prompt.
  28.    Boot the system to the 0S/2 v 1.3 install diskette
  29.    - then hit <Esc> to get an OS/2 prompt
  30.  
  31. Save a complete copy of all the files in the root directory of disk drive C: 
  32.    into a temporary subdirectory. This is so that you can get back to where 
  33.    you started should you choose to do so.
  34. -  From the root directory type     MD SAVE
  35. -  then type                        COPY C:\*.* C:\SAVE
  36.  
  37. Insert the ASW-1220/1420 v 1.3 diskette into the A: (or B:) floppy drive.
  38.  
  39. -- Copy all the files from A:\DISK0, A:\DISK0\1540, and A:\DISK0\SHARE to 
  40.      the root directory of C:
  41.      -  Type                    COPY A:\DISKO\*.* C:\
  42.      -  then type               COPY A:\DISK0\1540\*.* C:\
  43.      -  then type               COPY A:\DISKO\SHARE\*.* C:\
  44. This step will overwrite some of the system files. The original files are 
  45.    in C:\SAVE
  46.  
  47. "Down" the system, turn off the power, and install the AHA-1540/1542 board 
  48. into your system. Although the default jumper setting on the board is 
  49. correct for most systems, please adjust the jumpers as required to avoid 
  50. any possible Interrupt, DMA or Port Address conflicts. Refer to the 
  51. Installation Guide.
  52.  
  53. -- Reboot the system. The system should boot and automatically load 
  54.      the necessary LADDR drivers to support the AHA-1540/1542 board. 
  55.      No changes to the CONFIG.SYS file are necessary for disk.
  56.  
  57. Notes:
  58.  
  59. -- This same procedure can also be used to install the AHA-1740, AHA-1640 
  60.       or AHA-1520/1522 boards.
  61.    In the fourth step, be sure to copy the files for your board type 
  62.       to the root director)' on C:
  63.       For example: For the AHA-1520\1522, type COPY A:\DISK0\1520\*.* C:\
  64.  
  65. For the addition of peripherals other than disk (e.g. CD-ROM), changes 
  66.   to the CONFIG.SYS file may also be required. Please refer to the 
  67.   ASW-1220/1420 v 1.3 Installation Guide for more information.
  68.  
  69.  
  70.