GF#3030 Operator aborted the operation from kbd. The call was canceled.
[3002]
GF#3031 Operator aborted the operation with a Ctrl-Break.
[3003]
GF#3032 Operator aborted the operation, exit flag set.
[3004]
GF#3033 The Answer operation requested by this record was completed.
; The status codes for any incoming calls received during the time this record was active are now posted elsewhere in the received list.
[3006]
GF#3035 Remote operator request.
[3007]
GF#3036 Remote operator request.
[300B]
GF#3040 A command was used that is currently undefined.
[300C]
GF#3041 A command was used that is unknown to the program.
[3016]
GF#3051 A file-I/O error occurred in opening the log file.
[3017]
GF#3052 There was an error opening or reading the indirect file.
; given in the phone number field of a queue record. The file does not exist or is not in a valid format.
[301F]
GF#3060 Answer error - no open files. Check the name of the receive file.
[3020]
GF#3061 Answer error - invalid drive in receive filename.
[3021]
GF#3062 Answer error - insufficient disk space - phone will not be answered.
[3029]
GF#3070 No answer received - busy or wrong number.
[302A]
GF#3071 The number being dialed is blocked or prohibited from use.
[302B]
GF#3072 Dial error - phone rang.
[302C]
GF#3073 Dial error - blocked number table full.
[302D]
GF#3074 Dial error - blocked wait delay.
[3033]
GF#3080 Dial error - no open files.
;This error is reported when there is nothing to send or no file to receive, and thus there is no point in placing the call, so the activity is canceled.
[303D]
GF#3090 Hold error - illegal time specified in HOLD command.
[3047]
GF#3100 No file specified for LIST operation.
[3048]
GF#3101 The program was unable to open the LIST file.
[3049]
GF#3102 Too many files were specified in the send list. There is a 50-file limit per list.
[304A]
GF#3103 List error - cannot find file named in list.
[304C]
GF#3105 The LOG file specified was not opened.
[304D]
GF#3106 The parameter for the LOG command is incorrect.
[3051]
GF#3110 The NUMBERS command did not specify a file.
[3052]
GF#3111 The NUMBERS command was unable to open the file.
[305B]
GF#3120 Rate error - illegal value. Use only 0, 2400, 4800, 7200, 9600, 12000, or 14400.
[3065]
GF#3130 Receive error - the file specified was not opened.
[306F]
GF#3140 Send error - too many files were specified in the send list.
;There is a 50-file limit per list.
[3070]
GF#3141 Send error - a queue record had an invalid source type.
[3079]
GF#3150 GCL-report file not found.
[307A]
GF#3151 GCL-report buffer to short.
[307E]
Gammafax board error number 3155
[3083]
GF#3160 Specified font file not found.
[3084]
GF#3161 Error reading font file.
[308D]
GF#3170 Invalid image compression.
[308E]
GF#3171 Invalid image width.
[3097]
GF#3180 Filename indexing error - unable to index page count.
[30A1]
GF#3190 Filename indexing error - unable to index fax-call number.
[30AB]
GF#3200 A DIS signal was not received from the remote fax machine.
; (Dial and Receive case). There are indications that the remote machine was either a Group 1 fax, a Group 2 fax, or possibly some other type of CCITT V.xx series modem.
[30AC]
GF#3201 Nothing to poll; the remote fax machine's tray is empty.
[30AD]
GF#3202 Disconnect command received from the remote fax machine.
[30AE]
GF#3203 Poll attempt failed; the remote fax machine didn't send a DCS.
[30AF]
GF#3204 Training failed during polling the line quality is unusable.
[30B0]
GF#3205 Image quality failed - phone line noisy during polling.
[30B1]
GF#3206 Protocol failed. Disconnect sent to remote fax during polling.
[30B5]
GF#3210 Digital ID Signal (DIS) received a disconnect message.
[30B6]
GF#3211 DCS was not received from the sending fax machine.
[30B7]
GF#3212 A disconnect command was received from the remote fax machine.
; during protocol negotiation before receiving a fax.
[30B8]
GF#3213 The protocol negotiation failed to agree on capabilities.
; that would work for this call. The phone connection could have been bad or the capabilities of the sending machine too limited.
[30B9]
GF#3214 A disconnect command was received from the remote fax machine.
; at page break after receiving a fax.
[30BA]
GF#3215 A time-out occurred at page break when receiving an image.
; Protocol error caused a disconnect to be sent.
[30BB]
GF#3216 Board is configured to only accept fine resolution images.
;The remote fax machine attempted to send a standard resolution image.
[30BC]
GF#3217 Board is configured to only accept faxes in ECM mode.
;The remote fax machine attempted to send a fax without Error Correcting Mode (ECM)
[30BD]
GF#3218 The remote machine does not support unlimited page length.
; and the fax board was configured to require unlimited page length.
[30BE]
GF#3219 The remote fax machine attempted to use an unknown modulation.
[30BF]
GF#3220 A DIS signal was not received from the remote fax machine.
; (Dial and Send case). There are indications that the remote machine was either a Group 1 fax, a Group 2 fax, or possibly some other type of CCITT V.xx series modem.
[30C0]
GF#3221 The remote fax machine failed to confirm the page (RTN).
[30C1]
GF#3222 A Procedure Interrupt was received; no confirmation.
[30C2]
GF#3223 An unexpected disconnect message was received.
[30C3]
GF#3224 The remote machine failed to respond.
[30C4]
GF#3225 An unknown protocol message was received.
[30C9]
GF#3230 A disconnect message was received while attempting to negotiate
[30CA]
GF#3231 Protocol error caused a disconnect to be sent.
; while attempting to negotiate transmission characteristics.
[30CB]
GF#3232 An attempt was made to send MR compressed file to MH-only unit.
[30CC]
GF#3233 Can't send Fine res. to machine that only receives standard.
[30CD]
GF#3234 Remote machine that does not have ECM, and ECM was REQUIRED.
;An attempt was made to send a file in Error Correcting Mode to a for this transaction.
[30D3]
GF#3240 A disconnect message was received while being polled.
[30D4]
GF#3241 The remote machine did not send DTC while being polled.
[30D5]
GF#3242 Remote fax failed to confirm the page (RTN) while being polled.
[30D6]
GF#3243 Remote fax failed to confirm the page (PIP) while being polled.
[30D7]
GF#3244 Remote fax failed to respond to a page break while being polled
[30D8]
GF#3245 An unknown response has been received from the remote machine.
[30DD]
GF#3250 A fax was received which had too many bad scan lines.
[30DE]
GF#3251 Fax received had too high a percentage of bad scan lines.
[30DF]
GF#3252 A fax was received which had too many bad scan lines in a row.
[30E0]
GF#3253 Fax was received which had a high percentage of bad scan lines.
;, but not high enough to fail the call.
[30E2]
GF#3255 The received image has no scan lines.
[30E3]
GF#3256 Image too short, received image is less than required minimum.
[30E7]
GF#3260 DIS not received in error-correcting mode.
[30E8]
GF#3261 DIS received disconnect while in error-correcting mode.
[30EB]
GF#3264 DCN was received during ECM transmission.
[30EC]
GF#3265 DCN received in error-correcting mode; same as 3223.
[30ED]
GF#3266 RTN received in error-correcting mode; same as 3221.
[30EE]
GF#3267 PIN received in error-correcting mode; same as 3222.
[30EF]
GF#3268 Time-out received in error-correcting mode; same as 3224.
[30F0]
GF#3269 Unknown response in error-correcting mode; same as 3225.
[30F1]
GF#3270 Received partial page request at lowest allowed ECM data rate.
;in error-correcting mode - cannot downspeed.
;GammaFAX Error Codes [31xx]
[3110]
GF#3300 The program encountered an I/O error when reading a file.
; There was either a physical I/O error or a file with no data.
GF#3311 Image file length does not meet minimum requirements.
[3124]
GF#3320 No file available for writing image data.
[3125]
GF#3321 File-write error on image file data; check disk space.
[3126]
GF#3322 Image received exceeds memory allocation available.
[3142]
GF#3350 No file open for writing received image data.
[3143]
GF#3351 File-write error; check disk space available.
[3174]
GF#3400 File-transfer initial acknowledge not received.
[3175]
GF#3401 File transfer unable to get remote response.
[3176]
GF#3402 File transfer encountered block sequence error.
[3177]
GF#3403 File transfer encountered block sequence error.
[3178]
GF#3404 File transfer failed to get sign-off response.
[317E]
GF#3410 File-transfer initialization message not received.
[317F]
GF#3411 File transfer failed to respond to a reject message.
[3180]
GF#3412 File transfer encountered too many frame errors.
[3181]
GF#3413 File transfer failed to open the receive file.
[3182]
GF#3414 File-transfer write error; check disk space available.
[31D8]
GF#3500 Queue-record ID/ROM ID mismatch.
[31D9]
GF#3501 Unsupported BIOS system service call.
[31E2]
GF#3510 PC did not provide enough service to the CP card.
; in time for transaction to complete. This error indicates the host is under powered or improperly configured to act as a facsimile host.
[31EC]
GF#3520 The queue record buffer is in use.
[31ED]
GF#3521 Invalid state for this operation.
[31F1]
GF#3525 The rate requested is less than the minimum rate.
[31F2]
GF#3526 The rate requested is greater than the maximum rate.
;GammaFAX Error Codes [32xx]
[323D]
GF#3600 GCL - Syntax error.
[323E]
GF#3601 GCL - Value out of range.
[3280]
Gammafax board error number 3667
[32A1]
GF#3700 Operating system error.
;GammaFAX Error Codes [33xx]
[336B]
GF#3901 Bad parameter in modem-interface call.
[336C]
GF#3902 Requested option has not been implemented.
[336D]
GF#3903 Option value in call is not supported.
[336E]
GF#3904 Pulse dial circuits on the card not be acceptable to this PTT.
;Parameter value in call is out of range. The , and this error informs the user that pulse dialing has been disabled for that administration.
[336F]
GF#3905 Line request failed; line not open.
[3370]
GF#3906 Protocol time-out on communications line.
[3371]
GF#3907 No buffer was available for line protocol.
[3372]
GF#3908 Length parameter specified was invalid.
[3373]
GF#3909 Reject message received by line protocol.
[3374]
GF#3910 Dial tone was not detected during dialing.
;Various factors can cause dialtone not to be reported beyond the simple case of a broken or misconnected phone cord. The dialtone signal strength, frequency and pattern are all measured and must meet the software expectations.
[3375]
GF#3911 Ring detection did not complete successfully.
[3376]
GF#3912 No answer tone detected.
;The program is unable to classify incoming signals (i.e., there was no busy condition, no ring, no audio energy was detected, etc.).
[3377]
GF#3913 Carrier was not detected during image transfer.
[3378]
GF#3914 Quality test failed; phone-line quality poor.
[3379]
GF#3915 Quality test failed; phone-line quality poor.
[337A]
GF#3916 Command time-out; command not received.
[337B]
GF#3917 Command signal exceeded maximum value permitted.
[337C]
GF#3918 Command signal exceeded minimum value permitted.
[337E]
GF#3920 Protocol time-out.
[337F]
GF#3921 Training algorithm detected FSK.
[3380]
GF#3922 Training algorithm found no P2.
[3381]
GF#3923 Training algorithm found no PN.
[3388]
GF#3930 Answer tone detected.
[3389]
GF#3931 Busy tone detected.
;This error is reported when the busy tone "on" time exceeds 300 milliseconds.
[338A]
GF#3932 Fast Busy - Telephone Network congestion detected.
; This error is reported when the busy cadence (on/off tone pattern) is less than 300 milliseconds "on". The user hears a very fast beeping on the line.
[338B]
GF#3933 No audio energy detected - line was silent after dialing.
;("high & dry"). This might be the case with a totally hung dial, or possibly when "blind" dial is in use (dial tone detection has been suppressed) and the phone cord is damaged or disconnected.
[338C]
GF#3934 Voice response to call.
[338D]
GF#3935 Ringing detected - no answer.
;This error informs the user that a number was successfully reached and ringing at the remote end was reported. If there is no answer, the fax machine could be off-line (may be out of paper) and not responding.
[338E]
GF#3936 Ringing detected, then silence, but no answer.
;In this situation, ring back was detected and then followed by a period of at least six seconds where there was no further ringing, no answer tone, perhaps no audio energy. This message will most likely occur if a voice phone is called and a person
answers, or if the call results in some type of operator intercept, or if the fax machine number is not on an outside line and the PBX operator is unable to switch to the internal fax line.
[338F]
GF#3937 Ringing detected followed by a busy signal.
[3390]
GF#3938 Ring for a short time period.
[3392]
GF#3940 Telephone line loop current was not detected after dialing.
;Any premature disconnect of the line will cause loop current to cease and the call is history at that point.
[3393]
GF#3941 Telephone loop current failed during transmission/reception.
; (the remote machine may have terminated the call or the phone system may have disconnected).
[3394]
GF#3942 Loop current was detected prior to dialing.
; (the handset was in use, for example).
; Network_Error_Class range in [WFXNET] section is 80-BF
; 80xx Novell IPX
[8001]
IPX network services not present (Novell Netware).
Make sure IPX or IPXODI network driver is loaded before
loading the Delrina Network Communications drivers.
[8002]
Insufficient network IPX SOCKETS available (Novell Netware).
Edit the NET.CFG or SHELL.CFG file (depending on your network)
to include a SOCKETS setting of at least 20, as follows:
.
For regular IPX, insert:
IPX SOCKETS = 32
.
For IPXODI, change the SOCKETS line under PROTOCOL STACK IPX to:
SOCKETS =32
; 81xx Windows for Workgroups-IPX
[8101]
IPX network services not present (Windows for Workgroups with Novell Netware).
Make sure IPX or IPXODI network driver is loaded before
loading the Delrina Network Communications drivers.
.
If using MSIPX, consider upgrading to IPXODI network drivers.
[8102]
Insufficient IPX SOCKETS available (Windows for Workgroups with Novell Netware)
Edit the NET.CFG or SHELL.CFG file (depending on your network)
to include a SOCKETS setting of at least 20, as follows:
.
For regular IPX, insert:
IPX SOCKETS = 32
.
For IPXODI, change the SOCKETS line under PROTOCOL STACK IPX to:
SOCKETS =32
.
If using MSIPX drivers, consider upgrading to IPXODI network drivers.
; 82xx Windows for Workgroups-NETBEUI
[8201]
Windows for Workgroups NETBEUI network services not present.
NETBEUI network services must be loaded before loading the Delrina Network
Communications drivers.Add the command NETBEUI to the NET START command
line in AUTOEXEC.BAT:
.
NET START NETBEUI
[8202]
Insufficient NETBEUI Network Resources (Windows for Workgroups).
Increase NCBS setting to at least 64, more if other network services use NCBS.
.
In PROTOCOL.INI, change the NCBS and SESSIONS lines in PROTOCOL.INI as follows:
.
NCBS=64
SESSIONS=32
; 83xx Lantastic-NETBIOS
[8301]
NETBIOS network services not present (Lantastic).
NETBIOS services must be loaded prior to loading the
