home *** CD-ROM | disk | FTP | other *** search
/ Il CD di internet / CD.iso / SOURCE / KERNEL-S / V1.2 / LINUX-1.2 / LINUX-1 / linux / drivers / net / znet.c < prev   
Encoding:
C/C++ Source or Header  |  1995-03-07  |  24.9 KB  |  763 lines

  1. /* znet.c: An Zenith Z-Note ethernet driver for linux. */
  2.  
  3. static char *version = "znet.c:v1.02 9/23/94 becker@cesdis.gsfc.nasa.gov\n";
  4.  
  5. /*
  6.     Written by Donald Becker.
  7.  
  8.     The author may be reached as becker@cesdis.gsfc.nasa.gov.
  9.     This driver is based on the Linux skeleton driver.  The copyright of the
  10.     skeleton driver is held by the United States Government, as represented
  11.     by DIRNSA, and it is released under the GPL.
  12.  
  13.     Thanks to Mike Hollick for alpha testing and suggestions.
  14.  
  15.   References:
  16.        The Crynwr packet driver.
  17.  
  18.       "82593 CSMA/CD Core LAN Controller" Intel datasheet, 1992
  19.       Intel Microcommunications Databook, Vol. 1, 1990.
  20.     As usual with Intel, the documentation is incomplete and inaccurate.
  21.     I had to read the Crynwr packet driver to figure out how to actually
  22.     use the i82593, and guess at what register bits matched the loosely
  23.     related i82586.
  24.  
  25.                     Theory of Operation
  26.  
  27.     The i82593 used in the Zenith Z-Note series operates using two(!) slave
  28.     DMA    channels, one interrupt, and one 8-bit I/O port.
  29.  
  30.     While there    several ways to configure '593 DMA system, I chose the one
  31.     that seemed commensurate with the highest system performance in the face
  32.     of moderate interrupt latency: Both DMA channels are configured as
  33.     recirculating ring buffers, with one channel (#0) dedicated to Rx and
  34.     the other channel (#1) to Tx and configuration.  (Note that this is
  35.     different than the Crynwr driver, where the Tx DMA channel is initialized
  36.     before each operation.  That approach simplifies operation and Tx error
  37.     recovery, but requires additional I/O in normal operation and precludes
  38.     transmit buffer    chaining.)
  39.  
  40.     Both rings are set to 8192 bytes using {TX,RX}_RING_SIZE.  This provides
  41.     a reasonable ring size for Rx, while simplifying DMA buffer allocation --
  42.     DMA buffers must not cross a 128K boundary.  (In truth the size selection
  43.     was influenced by my lack of '593 documentation.  I thus was constrained
  44.     to use the Crynwr '593 initialization table, which sets the Rx ring size
  45.     to 8K.)
  46.  
  47.     Despite my usual low opinion about Intel-designed parts, I must admit
  48.     that the bulk data handling of the i82593 is a good design for
  49.     an integrated system, like a laptop, where using two slave DMA channels
  50.     doesn't pose a problem.  I still take issue with using only a single I/O
  51.     port.  In the same controlled environment there are essentially no
  52.     limitations on I/O space, and using multiple locations would eliminate
  53.     the    need for multiple operations when looking at status registers,
  54.     setting the Rx ring boundary, or switching to promiscuous mode.
  55.  
  56.     I also question Zenith's selection of the '593: one of the advertised
  57.     advantages of earlier Intel parts was that if you figured out the magic
  58.     initialization incantation you could use the same part on many different
  59.     network types.  Zenith's use of the "FriendlyNet" (sic) connector rather
  60.     than an    on-board transceiver leads me to believe that they were planning
  61.     to take advantage of this.  But, uhmmm, the '593 omits all but ethernet
  62.     functionality from the serial subsystem.
  63.  */
  64.  
  65. #include <linux/kernel.h>
  66. #include <linux/sched.h>
  67. #include <linux/string.h>
  68. #include <linux/ptrace.h>
  69. #include <linux/errno.h>
  70. #include <linux/interrupt.h>
  71. #include <linux/ioport.h>
  72. #include <asm/system.h>
  73. #include <asm/bitops.h>
  74. #include <asm/io.h>
  75. #include <asm/dma.h>
  76.  
  77. #include <linux/netdevice.h>
  78. #include <linux/etherdevice.h>
  79. #include <linux/skbuff.h>
  80. #include <linux/if_arp.h>
  81.  
  82. #ifndef ZNET_DEBUG
  83. #define ZNET_DEBUG 1
  84. #endif
  85. static unsigned int znet_debug = ZNET_DEBUG;
  86.  
  87. /* The DMA modes we need aren't in <dma.h>. */
  88. #define DMA_RX_MODE        0x14    /* Auto init, I/O to mem, ++, demand. */
  89. #define DMA_TX_MODE        0x18    /* Auto init, Mem to I/O, ++, demand. */
  90. #define dma_page_eq(ptr1, ptr2) ((long)(ptr1)>>17 == (long)(ptr2)>>17)
  91. #define DMA_BUF_SIZE 8192
  92. #define RX_BUF_SIZE 8192
  93. #define TX_BUF_SIZE 8192
  94.  
  95. /* Commands to the i82593 channel 0. */
  96. #define CMD0_CHNL_0            0x00
  97. #define CMD0_CHNL_1            0x10        /* Switch to channel 1. */
  98. #define CMD0_NOP (CMD0_CHNL_0)
  99. #define CMD0_PORT_1    CMD0_CHNL_1
  100. #define CMD1_PORT_0    1
  101. #define CMD0_IA_SETUP        1
  102. #define CMD0_CONFIGURE        2
  103. #define CMD0_MULTICAST_LIST 3
  104. #define CMD0_TRANSMIT        4
  105. #define CMD0_DUMP            6
  106. #define CMD0_DIAGNOSE        7
  107. #define CMD0_Rx_ENABLE        8
  108. #define CMD0_Rx_DISABLE        10
  109. #define CMD0_Rx_STOP        11
  110. #define CMD0_RETRANSMIT        12
  111. #define CMD0_ABORT            13
  112. #define CMD0_RESET            14
  113.  
  114. #define CMD0_ACK 0x80
  115.  
  116. #define CMD0_STAT0 (0 << 5)
  117. #define CMD0_STAT1 (1 << 5)
  118. #define CMD0_STAT2 (2 << 5)
  119. #define CMD0_STAT3 (3 << 5)
  120.  
  121. #define net_local znet_private
  122. struct znet_private {
  123.     int rx_dma, tx_dma;
  124.     struct enet_statistics stats;
  125.     /* The starting, current, and end pointers for the packet buffers. */
  126.     ushort *rx_start, *rx_cur, *rx_end;
  127.     ushort *tx_start, *tx_cur, *tx_end;
  128.     ushort tx_buf_len;            /* Tx buffer length, in words. */
  129. };
  130.  
  131. /* Only one can be built-in;-> */
  132. static struct znet_private zn;
  133. static ushort dma_buffer1[DMA_BUF_SIZE/2];
  134. static ushort dma_buffer2[DMA_BUF_SIZE/2];
  135. static ushort dma_buffer3[DMA_BUF_SIZE/2 + 8];
  136.  
  137. /* The configuration block.  What an undocumented nightmare.  The first
  138.    set of values are those suggested (without explanation) for ethernet
  139.    in the Intel 82586 databook.     The rest appear to be completely undocumented,
  140.    except for cryptic notes in the Crynwr packet driver.  This driver uses
  141.    the Crynwr values verbatim. */
  142.  
  143. static unsigned char i593_init[] = {
  144.   0xAA,                    /* 0: 16-byte input & 80-byte output FIFO. */
  145.                         /*      threshold, 96-byte FIFO, 82593 mode. */
  146.   0x88,                    /* 1: Continuous w/interrupts, 128-clock DMA.*/
  147.   0x2E,                    /* 2: 8-byte preamble, NO address insertion, */
  148.                         /*      6-byte Ethernet address, loopback off.*/
  149.   0x00,                    /* 3: Default priorities & backoff methods. */
  150.   0x60,                    /* 4: 96-bit interframe spacing. */
  151.   0x00,                    /* 5: 512-bit slot time (low-order). */
  152.   0xF2,                    /* 6: Slot time (high-order), 15 COLL retries. */
  153.   0x00,                    /* 7: Promisc-off, broadcast-on, default CRC. */
  154.   0x00,                    /* 8: Default carrier-sense, collision-detect. */
  155.   0x40,                    /* 9: 64-byte minimum frame length. */
  156.   0x5F,                    /* A: Type/length checks OFF, no CRC input,
  157.                            "jabber" termination, etc. */
  158.   0x00,                    /* B: Full-duplex disabled. */
  159.   0x3F,                    /* C: Default multicast addresses & backoff. */
  160.   0x07,                    /* D: Default IFS retriggering. */
  161.   0x31,                    /* E: Internal retransmit, drop "runt" packets,
  162.                            synchr. DRQ deassertion, 6 status bytes. */
  163.   0x22,                    /* F: Receive ring-buffer size (8K), 
  164.                            receive-stop register enable. */
  165. };
  166.  
  167. struct netidblk {
  168.     char magic[8];        /* The magic number (string) "NETIDBLK" */
  169.     unsigned char netid[8]; /* The physical station address */
  170.     char nettype, globalopt;
  171.     char vendor[8];        /* The machine vendor and product name. */
  172.     char product[8];
  173.     char irq1, irq2;        /* Interrupts, only one is currently used.    */
  174.     char dma1, dma2;
  175.     short dma_mem_misc[8];        /* DMA buffer locations (unused in Linux). */
  176.     short iobase1, iosize1;
  177.     short iobase2, iosize2;        /* Second iobase unused. */
  178.     char driver_options;            /* Misc. bits */
  179.     char pad;
  180. };
  181.  
  182. int znet_probe(struct device *dev);
  183. static int    znet_open(struct device *dev);
  184. static int    znet_send_packet(struct sk_buff *skb, struct device *dev);
  185. static void    znet_interrupt(int irq, struct pt_regs *regs);
  186. static void    znet_rx(struct device *dev);
  187. static int    znet_close(struct device *dev);
  188. static struct enet_statistics *net_get_stats(struct device *dev);
  189. static void set_multicast_list(struct device *dev, int num_addrs, void *addrs);
  190. static void hardware_init(struct device *dev);
  191. static void update_stop_hit(short ioaddr, unsigned short rx_stop_offset);
  192.  
  193. #ifdef notdef
  194. static struct sigaction znet_sigaction = { &znet_interrupt, 0, 0, NULL, };
  195. #endif
  196.  
  197.  
  198. /* The Z-Note probe is pretty easy.  The NETIDBLK exists in the safe-to-probe
  199.    BIOS area.  We just scan for the signature, and pull the vital parameters
  200.    out of the structure. */
  201.  
  202. int znet_probe(struct device *dev)
  203. {
  204.     int i;
  205.     struct netidblk *netinfo;
  206.     char *p;
  207.  
  208.     /* This code scans the region 0xf0000 to 0xfffff for a "NETIDBLK". */
  209.     for(p = (char *)0xf0000; p < (char *)0x100000; p++)
  210.         if (*p == 'N'  &&  strncmp(p, "NETIDBLK", 8) == 0)
  211.             break;
  212.  
  213.     if (p >= (char *)0x100000) {
  214.         if (znet_debug > 1)
  215.             printk(KERN_INFO "No Z-Note ethernet adaptor found.\n");
  216.         return ENODEV;
  217.     }
  218.     netinfo = (struct netidblk *)p;
  219.     dev->base_addr = netinfo->iobase1;
  220.     dev->irq = netinfo->irq1;
  221.  
  222.     printk(KERN_INFO "%s: ZNET at %#3x,", dev->name, dev->base_addr);
  223.  
  224.     /* The station address is in the "netidblk" at 0x0f0000. */
  225.     for (i = 0; i < 6; i++)
  226.         printk(" %2.2x", dev->dev_addr[i] = netinfo->netid[i]);
  227.  
  228.     printk(", using IRQ %d DMA %d and %d.\n", dev->irq, netinfo->dma1,
  229.         netinfo->dma2);
  230.  
  231.     if (znet_debug > 1) {
  232.         printk(KERN_INFO "%s: vendor '%16.16s' IRQ1 %d IRQ2 %d DMA1 %d DMA2 %d.\n",
  233.                dev->name, netinfo->vendor,
  234.                netinfo->irq1, netinfo->irq2,
  235.                netinfo->dma1, netinfo->dma2);
  236.         printk(KERN_INFO "%s: iobase1 %#x size %d iobase2 %#x size %d net type %2.2x.\n",
  237.                dev->name, netinfo->iobase1, netinfo->iosize1,
  238.                netinfo->iobase2, netinfo->iosize2, netinfo->nettype);
  239.     }
  240.  
  241.     if (znet_debug > 0)
  242.         printk("%s%s", KERN_INFO, version);
  243.  
  244.     dev->priv = (void *) &zn;
  245.     zn.rx_dma = netinfo->dma1;
  246.     zn.tx_dma = netinfo->dma2;
  247.  
  248.     /* These should never fail.  You can't add devices to a sealed box! */
  249.     if (request_irq(dev->irq, &znet_interrupt, 0, "ZNet")
  250.         || request_dma(zn.rx_dma,"ZNet rx")
  251.         || request_dma(zn.tx_dma,"ZNet tx")) {
  252.         printk(KERN_WARNING "%s: Not opened -- resource busy?!?\n", dev->name);
  253.         return EBUSY;
  254.     }
  255.     irq2dev_map[dev->irq] = dev;
  256.  
  257.     /* Allocate buffer memory.    We can cross a 128K boundary, so we
  258.        must be careful about the allocation.  It's easiest to waste 8K. */
  259.     if (dma_page_eq(dma_buffer1, &dma_buffer1[RX_BUF_SIZE/2-1]))
  260.       zn.rx_start = dma_buffer1;
  261.     else 
  262.       zn.rx_start = dma_buffer2;
  263.  
  264.     if (dma_page_eq(dma_buffer3, &dma_buffer3[RX_BUF_SIZE/2-1]))
  265.       zn.tx_start = dma_buffer3;
  266.     else
  267.       zn.tx_start = dma_buffer2;
  268.     zn.rx_end = zn.rx_start + RX_BUF_SIZE/2;
  269.     zn.tx_buf_len = TX_BUF_SIZE/2;
  270.     zn.tx_end = zn.tx_start + zn.tx_buf_len;
  271.  
  272.     /* The ZNET-specific entries in the device structure. */
  273.     dev->open = &znet_open;
  274.     dev->hard_start_xmit = &znet_send_packet;
  275.     dev->stop = &znet_close;
  276.     dev->get_stats    = net_get_stats;
  277.     dev->set_multicast_list = &set_multicast_list;
  278.  
  279.     /* Fill in the 'dev' with ethernet-generic values. */
  280.     ether_setup(dev);
  281.  
  282.     return 0;
  283. }
  284.  
  285.  
  286. static int znet_open(struct device *dev)
  287. {
  288.     int ioaddr = dev->base_addr;
  289.  
  290.     if (znet_debug > 2)
  291.         printk(KERN_DEBUG "%s: znet_open() called.\n", dev->name);
  292.  
  293.     /* Turn on the 82501 SIA, using zenith-specific magic. */
  294.     outb(0x10, 0xe6);                    /* Select LAN control register */
  295.     outb(inb(0xe7) | 0x84, 0xe7);        /* Turn on LAN power (bit 2). */
  296.     /* According to the Crynwr driver we should wait 50 msec. for the
  297.        LAN clock to stabilize.  My experiments indicates that the '593 can
  298.        be initialized immediately.  The delay is probably needed for the
  299.        DC-to-DC converter to come up to full voltage, and for the oscillator
  300.        to be spot-on at 20Mhz before transmitting.
  301.        Until this proves to be a problem we rely on the higher layers for the
  302.        delay and save allocating a timer entry. */
  303.  
  304.     /* This follows the packet driver's lead, and checks for success. */
  305.     if (inb(ioaddr) != 0x10 && inb(ioaddr) != 0x00)
  306.         printk(KERN_WARNING "%s: Problem turning on the transceiver power.\n",
  307.                dev->name);
  308.  
  309.     dev->tbusy = 0;
  310.     dev->interrupt = 0;
  311.     hardware_init(dev);
  312.     dev->start = 1;
  313.  
  314.     return 0;
  315. }
  316.  
  317. static int znet_send_packet(struct sk_buff *skb, struct device *dev)
  318. {
  319.     int ioaddr = dev->base_addr;
  320.  
  321.     if (znet_debug > 4)
  322.         printk(KERN_DEBUG "%s: ZNet_send_packet(%d).\n", dev->name, dev->tbusy);
  323.  
  324.     /* Transmitter timeout, likely just recovery after suspending the machine. */
  325.     if (dev->tbusy) {
  326.         ushort event, tx_status, rx_offset, state;
  327.         int tickssofar = jiffies - dev->trans_start;
  328.         if (tickssofar < 10)
  329.             return 1;
  330.         outb(CMD0_STAT0, ioaddr); event = inb(ioaddr);
  331.         outb(CMD0_STAT1, ioaddr); tx_status = inw(ioaddr);
  332.         outb(CMD0_STAT2, ioaddr); rx_offset = inw(ioaddr);
  333.         outb(CMD0_STAT3, ioaddr); state = inb(ioaddr);
  334.         printk(KERN_WARNING "%s: transmit timed out, status %02x %04x %04x %02x,"
  335.                " resetting.\n", dev->name, event, tx_status, rx_offset, state);
  336.         if (tx_status == 0x0400)
  337.           printk(KERN_WARNING "%s: Tx carrier error, check transceiver cable.\n",
  338.                  dev->name);
  339.         outb(CMD0_RESET, ioaddr);
  340.         hardware_init(dev);
  341.     }
  342.  
  343.     if (skb == NULL) {
  344.         dev_tint(dev);
  345.         return 0;
  346.     }
  347.  
  348.     /* Check that the part hasn't reset itself, probably from suspend. */
  349.     outb(CMD0_STAT0, ioaddr);
  350.     if (inw(ioaddr) == 0x0010
  351.         && inw(ioaddr) == 0x0000
  352.         && inw(ioaddr) == 0x0010)
  353.       hardware_init(dev);
  354.  
  355.     /* Block a timer-based transmit from overlapping.  This could better be
  356.        done with atomic_swap(1, dev->tbusy), but set_bit() works as well. */
  357.     if (set_bit(0, (void*)&dev->tbusy) != 0)
  358.         printk(KERN_WARNING "%s: Transmitter access conflict.\n", dev->name);
  359.     else {
  360.         short length = ETH_ZLEN < skb->len ? skb->len : ETH_ZLEN;
  361.         unsigned char *buf = (void *)(skb+1);
  362.         ushort *tx_link = zn.tx_cur - 1;
  363.         ushort rnd_len = (length + 1)>>1;
  364.  
  365.         {
  366.             short dma_port = ((zn.tx_dma&3)<<2) + IO_DMA2_BASE;
  367.             unsigned addr = inb(dma_port);
  368.             addr |= inb(dma_port) << 8;
  369.             addr <<= 1;
  370.             if (((int)zn.tx_cur & 0x1ffff) != addr)
  371.               printk(KERN_WARNING "Address mismatch at Tx: %#x vs %#x.\n",
  372.                      (int)zn.tx_cur & 0xffff, addr);
  373.             zn.tx_cur = (ushort *)(((int)zn.tx_cur & 0xfe0000) | addr);
  374.         }
  375.  
  376.         if (zn.tx_cur >= zn.tx_end)
  377.           zn.tx_cur = zn.tx_start;
  378.         *zn.tx_cur++ = length;
  379.         if (zn.tx_cur + rnd_len + 1 > zn.tx_end) {
  380.             int semi_cnt = (zn.tx_end - zn.tx_cur)<<1; /* Cvrt to byte cnt. */
  381.             memcpy(zn.tx_cur, buf, semi_cnt);
  382.             rnd_len -= semi_cnt>>1;
  383.             memcpy(zn.tx_start, buf + semi_cnt, length - semi_cnt);
  384.             zn.tx_cur = zn.tx_start + rnd_len;
  385.         } else {
  386.             memcpy(zn.tx_cur, buf, skb->len);
  387.             zn.tx_cur += rnd_len;
  388.         }
  389.         *zn.tx_cur++ = 0;
  390.         cli(); {
  391.             *tx_link = CMD0_TRANSMIT + CMD0_CHNL_1;
  392.             /* Is this always safe to do? */
  393.             outb(CMD0_TRANSMIT + CMD0_CHNL_1,ioaddr);
  394.         } sti();
  395.  
  396.         dev->trans_start = jiffies;
  397.         if (znet_debug > 4)
  398.           printk(KERN_DEBUG "%s: Transmitter queued, length %d.\n", dev->name, length);
  399.     }
  400.     dev_kfree_skb(skb, FREE_WRITE); 
  401.     return 0;
  402. }
  403.  
  404. /* The ZNET interrupt handler. */
  405. static void    znet_interrupt(int irq, struct pt_regs * regs)
  406. {
  407.     struct device *dev = irq2dev_map[irq];
  408.     int ioaddr;
  409.     int boguscnt = 20;
  410.  
  411.     if (dev == NULL) {
  412.         printk(KERN_WARNING "znet_interrupt(): IRQ %d for unknown device.\n", irq);
  413.         return;
  414.     }
  415.  
  416.     dev->interrupt = 1;
  417.     ioaddr = dev->base_addr;
  418.  
  419.     outb(CMD0_STAT0, ioaddr);
  420.     do {
  421.         ushort status = inb(ioaddr);
  422.         if (znet_debug > 5) {
  423.             ushort result, rx_ptr, running;
  424.             outb(CMD0_STAT1, ioaddr);
  425.             result = inw(ioaddr);
  426.             outb(CMD0_STAT2, ioaddr);
  427.             rx_ptr = inw(ioaddr);
  428.             outb(CMD0_STAT3, ioaddr);
  429.             running = inb(ioaddr);
  430.             printk(KERN_DEBUG "%s: interrupt, status %02x, %04x %04x %02x serial %d.\n",
  431.                  dev->name, status, result, rx_ptr, running, boguscnt);
  432.         }
  433.         if ((status & 0x80) == 0)
  434.             break;
  435.  
  436.         if ((status & 0x0F) == 4) {    /* Transmit done. */
  437.             struct net_local *lp = (struct net_local *)dev->priv;
  438.             int tx_status;
  439.             outb(CMD0_STAT1, ioaddr);
  440.             tx_status = inw(ioaddr);
  441.             /* It's undocumented, but tx_status seems to match the i82586. */
  442.             if (tx_status & 0x2000) {
  443.                 lp->stats.tx_packets++;
  444.                 lp->stats.collisions += tx_status & 0xf;
  445.             } else {
  446.                 if (tx_status & 0x0600)  lp->stats.tx_carrier_errors++;
  447.                 if (tx_status & 0x0100)  lp->stats.tx_fifo_errors++;
  448.                 if (!(tx_status & 0x0040)) lp->stats.tx_heartbeat_errors++;
  449.                 if (tx_status & 0x0020)  lp->stats.tx_aborted_errors++;
  450.                 /* ...and the catch-all. */
  451.                 if (tx_status | 0x0760 != 0x0760)
  452.                   lp->stats.tx_errors++;
  453.             }
  454.             dev->tbusy = 0;
  455.             mark_bh(NET_BH);    /* Inform upper layers. */
  456.         }
  457.  
  458.         if ((status & 0x40)
  459.             || (status & 0x0f) == 11) {
  460.             znet_rx(dev);
  461.         }
  462.         /* Clear the interrupts we've handled. */
  463.         outb(CMD0_ACK,ioaddr);
  464.     } while (boguscnt--);
  465.  
  466.     dev->interrupt = 0;
  467.     return;
  468. }
  469.  
  470. static void znet_rx(struct device *dev)
  471. {
  472.     struct net_local *lp = (struct net_local *)dev->priv;
  473.     int ioaddr = dev->base_addr;
  474.     int boguscount = 1;
  475.     short next_frame_end_offset = 0;         /* Offset of next frame start. */
  476.     short *cur_frame_end;
  477.     short cur_frame_end_offset;
  478.  
  479.     outb(CMD0_STAT2, ioaddr);
  480.     cur_frame_end_offset = inw(ioaddr);
  481.  
  482.     if (cur_frame_end_offset == zn.rx_cur - zn.rx_start) {
  483.         printk(KERN_WARNING "%s: Interrupted, but nothing to receive, offset %03x.\n",
  484.                dev->name, cur_frame_end_offset);
  485.         return;
  486.     }
  487.  
  488.     /* Use same method as the Crynwr driver: construct a forward list in
  489.        the same area of the backwards links we now have.  This allows us to
  490.        pass packets to the upper layers in the order they were received --
  491.        important for fast-path sequential operations. */
  492.      while (zn.rx_start + cur_frame_end_offset != zn.rx_cur
  493.             && ++boguscount < 5) {
  494.         unsigned short hi_cnt, lo_cnt, hi_status, lo_status;
  495.         int count, status;
  496.  
  497.         if (cur_frame_end_offset < 4) {
  498.             /* Oh no, we have a special case: the frame trailer wraps around
  499.                the end of the ring buffer.  We've saved space at the end of
  500.                the ring buffer for just this problem. */
  501.             memcpy(zn.rx_end, zn.rx_start, 8);
  502.             cur_frame_end_offset += (RX_BUF_SIZE/2);
  503.         }
  504.         cur_frame_end = zn.rx_start + cur_frame_end_offset - 4;
  505.  
  506.         lo_status = *cur_frame_end++;
  507.         hi_status = *cur_frame_end++;
  508.         status = ((hi_status & 0xff) << 8) + (lo_status & 0xff);
  509.         lo_cnt = *cur_frame_end++;
  510.         hi_cnt = *cur_frame_end++;
  511.         count = ((hi_cnt & 0xff) << 8) + (lo_cnt & 0xff);
  512.  
  513.         if (znet_debug > 5)
  514.           printk(KERN_DEBUG "Constructing trailer at location %03x, %04x %04x %04x %04x"
  515.                  " count %#x status %04x.\n",
  516.                  cur_frame_end_offset<<1, lo_status, hi_status, lo_cnt, hi_cnt,
  517.                  count, status);
  518.         cur_frame_end[-4] = status;
  519.         cur_frame_end[-3] = next_frame_end_offset;
  520.         cur_frame_end[-2] = count;
  521.         next_frame_end_offset = cur_frame_end_offset;
  522.         cur_frame_end_offset -= ((count + 1)>>1) + 3;
  523.         if (cur_frame_end_offset < 0)
  524.           cur_frame_end_offset += RX_BUF_SIZE/2;
  525.     };
  526.  
  527.     /* Now step  forward through the list. */
  528.     do {
  529.         ushort *this_rfp_ptr = zn.rx_start + next_frame_end_offset;
  530.         int status = this_rfp_ptr[-4];
  531.         int pkt_len = this_rfp_ptr[-2];
  532.       
  533.         if (znet_debug > 5)
  534.           printk(KERN_DEBUG "Looking at trailer ending at %04x status %04x length %03x"
  535.                  " next %04x.\n", next_frame_end_offset<<1, status, pkt_len,
  536.                  this_rfp_ptr[-3]<<1);
  537.         /* Once again we must assume that the i82586 docs apply. */
  538.         if ( ! (status & 0x2000)) {                /* There was an error. */
  539.             lp->stats.rx_errors++;
  540.             if (status & 0x0800) lp->stats.rx_crc_errors++;
  541.             if (status & 0x0400) lp->stats.rx_frame_errors++;
  542.             if (status & 0x0200) lp->stats.rx_over_errors++; /* Wrong. */
  543.             if (status & 0x0100) lp->stats.rx_fifo_errors++;
  544.             if (status & 0x0080) lp->stats.rx_length_errors++;
  545.         } else if (pkt_len > 1536) {
  546.             lp->stats.rx_length_errors++;
  547.         } else {
  548.             /* Malloc up new buffer. */
  549.             struct sk_buff *skb;
  550.  
  551.             skb = alloc_skb(pkt_len, GFP_ATOMIC);
  552.             if (skb == NULL) {
  553.                 if (znet_debug)
  554.                   printk(KERN_WARNING "%s: Memory squeeze, dropping packet.\n", dev->name);
  555.                 lp->stats.rx_dropped++;
  556.                 break;
  557.             }
  558.             skb->len = pkt_len;
  559.             skb->dev = dev;
  560.  
  561.             if (&zn.rx_cur[(pkt_len+1)>>1] > zn.rx_end) {
  562.                 int semi_cnt = (zn.rx_end - zn.rx_cur)<<1;
  563.                 memcpy((unsigned char *) (skb + 1), zn.rx_cur, semi_cnt);
  564.                 memcpy((unsigned char *) (skb + 1) + semi_cnt, zn.rx_start,
  565.                        pkt_len - semi_cnt);
  566.             } else {
  567.                 memcpy((unsigned char *) (skb + 1), zn.rx_cur, pkt_len);
  568.                 if (znet_debug > 6) {
  569.                     unsigned int *packet = (unsigned int *) (skb + 1);
  570.                     printk(KERN_DEBUG "Packet data is %08x %08x %08x %08x.\n", packet[0],
  571.                            packet[1], packet[2], packet[3]);
  572.                 }
  573.           }
  574.  
  575. #ifdef HAVE_NETIF_RX
  576.             netif_rx(skb);
  577. #else
  578.             skb->lock = 0;
  579.             if (dev_rint((unsigned char*)skb, pkt_len, IN_SKBUFF, dev) != 0) {
  580.                 kfree(skb);
  581.                 lp->stats.rx_dropped++;
  582.                 break;
  583.             }
  584. #endif
  585.             lp->stats.rx_packets++;
  586.         }
  587.         zn.rx_cur = this_rfp_ptr;
  588.         if (zn.rx_cur >= zn.rx_end)
  589.             zn.rx_cur -= RX_BUF_SIZE/2;
  590.         update_stop_hit(ioaddr, (zn.rx_cur - zn.rx_start)<<1);
  591.         next_frame_end_offset = this_rfp_ptr[-3];
  592.         if (next_frame_end_offset == 0)        /* Read all the frames? */
  593.             break;            /* Done for now */
  594.         this_rfp_ptr = zn.rx_start + next_frame_end_offset;
  595.     } while (--boguscount);
  596.  
  597.     /* If any worth-while packets have been received, dev_rint()
  598.        has done a mark_bh(INET_BH) for us and will work on them
  599.        when we get to the bottom-half routine. */
  600.     return;
  601. }
  602.  
  603. /* The inverse routine to znet_open(). */
  604. static int znet_close(struct device *dev)
  605. {
  606.     int ioaddr = dev->base_addr;
  607.  
  608.     dev->tbusy = 1;
  609.     dev->start = 0;
  610.  
  611.     outb(CMD0_RESET, ioaddr);            /* CMD0_RESET */
  612.  
  613.     disable_dma(zn.rx_dma);
  614.     disable_dma(zn.tx_dma);
  615.  
  616.     free_irq(dev->irq);
  617.  
  618.     if (znet_debug > 1)
  619.         printk(KERN_DEBUG "%s: Shutting down ethercard.\n", dev->name);
  620.     /* Turn off transceiver power. */
  621.     outb(0x10, 0xe6);                    /* Select LAN control register */
  622.     outb(inb(0xe7) & ~0x84, 0xe7);        /* Turn on LAN power (bit 2). */
  623.  
  624.     return 0;
  625. }
  626.  
  627. /* Get the current statistics.    This may be called with the card open or
  628.    closed. */
  629. static struct enet_statistics *net_get_stats(struct device *dev)
  630. {
  631.         struct net_local *lp = (struct net_local *)dev->priv;
  632.  
  633.         return &lp->stats;
  634. }
  635.  
  636. #ifdef HAVE_MULTICAST
  637. /* Set or clear the multicast filter for this adaptor.
  638.    num_addrs == -1    Promiscuous mode, receive all packets
  639.    num_addrs == 0    Normal mode, clear multicast list
  640.    num_addrs > 0    Multicast mode, receive normal and MC packets, and do
  641.             best-effort filtering.
  642.    As a side effect this routine must also initialize the device parameters.
  643.    This is taken advantage of in open().
  644.  
  645.    N.B. that we change i593_init[] in place.  This (properly) makes the
  646.    mode change persistent, but must be changed if this code is moved to
  647.    a multiple adaptor environment.
  648.  */
  649. static void set_multicast_list(struct device *dev, int num_addrs, void *addrs)
  650. {
  651.     short ioaddr = dev->base_addr;
  652.  
  653.     if (num_addrs < 0) {
  654.         /* Enable promiscuous mode */
  655.         i593_init[7] &= ~3;        i593_init[7] |= 1;
  656.         i593_init[13] &= ~8;    i593_init[13] |= 8;
  657.     } else if (num_addrs > 0) {
  658.         /* Enable accept-all-multicast mode */
  659.         i593_init[7] &= ~3;        i593_init[7] |= 0;
  660.         i593_init[13] &= ~8;    i593_init[13] |= 8;
  661.     } else {                    /* Enable normal mode. */
  662.         i593_init[7] &= ~3;        i593_init[7] |= 0;
  663.         i593_init[13] &= ~8;    i593_init[13] |= 0;
  664.     }
  665.     *zn.tx_cur++ = sizeof(i593_init);
  666.     memcpy(zn.tx_cur, i593_init, sizeof(i593_init));
  667.     zn.tx_cur += sizeof(i593_init)/2;
  668.     outb(CMD0_CONFIGURE+CMD0_CHNL_1, ioaddr);
  669. #ifdef not_tested
  670.     if (num_addrs > 0) {
  671.         int addrs_len = 6*num_addrs;
  672.         *zn.tx_cur++ = addrs_len;
  673.         memcpy(zn.tx_cur, addrs, addrs_len);
  674.         outb(CMD0_MULTICAST_LIST+CMD0_CHNL_1, ioaddr);
  675.         zn.tx_cur += addrs_len>>1;
  676.     }
  677. #endif
  678. }
  679. #endif
  680.  
  681. void show_dma(void)
  682. {
  683.     short dma_port = ((zn.tx_dma&3)<<2) + IO_DMA2_BASE;
  684.     unsigned addr = inb(dma_port);
  685.     addr |= inb(dma_port) << 8;
  686.     printk("Addr: %04x cnt:%3x...", addr<<1, get_dma_residue(zn.tx_dma));
  687. }
  688.  
  689. /* Initialize the hardware.  We have to do this when the board is open()ed
  690.    or when we come out of suspend mode. */
  691. static void hardware_init(struct device *dev)
  692. {
  693.     short ioaddr = dev->base_addr;
  694.  
  695.     zn.rx_cur = zn.rx_start;
  696.     zn.tx_cur = zn.tx_start;
  697.  
  698.     /* Reset the chip, and start it up. */
  699.     outb(CMD0_RESET, ioaddr);
  700.  
  701.     cli(); {                            /* Protect against a DMA flip-flop */
  702.         disable_dma(zn.rx_dma);         /* reset by an interrupting task. */
  703.         clear_dma_ff(zn.rx_dma);
  704.         set_dma_mode(zn.rx_dma, DMA_RX_MODE);
  705.         set_dma_addr(zn.rx_dma, (unsigned int) zn.rx_start);
  706.         set_dma_count(zn.rx_dma, RX_BUF_SIZE);
  707.         enable_dma(zn.rx_dma);
  708.         /* Now set up the Tx channel. */
  709.         disable_dma(zn.tx_dma);
  710.         clear_dma_ff(zn.tx_dma);
  711.         set_dma_mode(zn.tx_dma, DMA_TX_MODE);
  712.         set_dma_addr(zn.tx_dma, (unsigned int) zn.tx_start);
  713.         set_dma_count(zn.tx_dma, zn.tx_buf_len<<1);
  714.         enable_dma(zn.tx_dma);
  715.     } sti();
  716.  
  717.     if (znet_debug > 1)
  718.       printk(KERN_DEBUG "%s: Initializing the i82593, tx buf %p... ", dev->name,
  719.              zn.tx_start);
  720.     /* Do an empty configure command, just like the Crynwr driver.  This
  721.        resets to chip to its default values. */
  722.     *zn.tx_cur++ = 0;
  723.     *zn.tx_cur++ = 0;
  724.     printk("stat:%02x ", inb(ioaddr)); show_dma();
  725.     outb(CMD0_CONFIGURE+CMD0_CHNL_1, ioaddr);
  726.     *zn.tx_cur++ = sizeof(i593_init);
  727.     memcpy(zn.tx_cur, i593_init, sizeof(i593_init));
  728.     zn.tx_cur += sizeof(i593_init)/2;
  729.     printk("stat:%02x ", inb(ioaddr)); show_dma();
  730.     outb(CMD0_CONFIGURE+CMD0_CHNL_1, ioaddr);
  731.     *zn.tx_cur++ = 6;
  732.     memcpy(zn.tx_cur, dev->dev_addr, 6);
  733.     zn.tx_cur += 3;
  734.     printk("stat:%02x ", inb(ioaddr)); show_dma();
  735.     outb(CMD0_IA_SETUP + CMD0_CHNL_1, ioaddr);
  736.     printk("stat:%02x ", inb(ioaddr)); show_dma();
  737.  
  738.     update_stop_hit(ioaddr, 8192);
  739.     if (znet_debug > 1)  printk("enabling Rx.\n");
  740.     outb(CMD0_Rx_ENABLE+CMD0_CHNL_0, ioaddr);
  741.     dev->tbusy = 0;
  742. }
  743.  
  744. static void update_stop_hit(short ioaddr, unsigned short rx_stop_offset)
  745. {
  746.     outb(CMD0_PORT_1, ioaddr);
  747.     if (znet_debug > 5)
  748.       printk(KERN_DEBUG "Updating stop hit with value %02x.\n",
  749.              (rx_stop_offset >> 6) | 0x80);
  750.     outb((rx_stop_offset >> 6) | 0x80, ioaddr);
  751.     outb(CMD1_PORT_0, ioaddr);
  752. }
  753.  
  754. /*
  755.  * Local variables:
  756.  *  compile-command: "gcc -D__KERNEL__ -I/usr/src/linux/net/inet -Wall -Wstrict-prototypes -O6 -m486 -c znet.c"
  757.  *  version-control: t
  758.  *  kept-new-versions: 5
  759.  *  c-indent-level: 4
  760.  *  tab-width: 4
  761.  * End:
  762.  */
  763.