home *** CD-ROM | disk | FTP | other *** search
/ NetNews Usenet Archive 1992 #26 / NN_1992_26.iso / spool / rec / models / rc / 4590 < prev    next >
Encoding:
Text File  |  1992-11-12  |  2.3 KB  |  56 lines

  1. Newsgroups: rec.models.rc
  2. Path: sparky!uunet!UB.com!pacbell.com!sgiblab!sdd.hp.com!think.com!yale.edu!yale!gumby!destroyer!cs.ubc.ca!unixg.ubc.ca!kakwa.ucs.ualberta.ca!ee.ualberta.ca!haley
  3. From: haley@ee.ualberta.ca (Richard Haley)
  4. Subject: motor speed control
  5. Message-ID: <haley.721592686@ee.ualberta.ca>
  6. Summary: parts list for schematic motor.ps
  7. Keywords: throttle , speed, motor
  8. Sender: news@kakwa.ucs.ualberta.ca
  9. Nntp-Posting-Host: eigen.ee.ualberta.ca
  10. Organization: University Of Alberta, Edmonton Canada
  11. Date: Thu, 12 Nov 1992 18:24:46 GMT
  12. Lines: 42
  13.  
  14.  
  15.  
  16. September 1992    Proportional DC electric Motor control 0 - 100%
  17. Circuit board for surface mount 3/4" x 2 1/8" 
  18. Valid for any DC motor with a current rating less than the FET used
  19. IRFZ48 60 Amps TO-220 $5 Can.
  20. Control connects to +/- and signal from Airtronics receiver 
  21. Circuit board replaces servo in standard mounting bracket
  22. Break existing circuit at fuse to allow current to flow through FET
  23. add one small wire to switch as reference for Q3
  24.  
  25. SPEED CONTROLLER PARTS LIST:
  26.  
  27. 1- LM324 Op Amp  (everybody makes one) Single supply, Quad, low cost
  28.    LM224, LM124 are temperature specs
  29.  
  30. R1, R2, R4, R5, R9, R12,R14 - 4.7 k resistors as small as possible
  31.                                         (or 2.2 k or whatever you
  32.                                         have lots of.)
  33. R3 - 33 k (ramp generator)
  34. R6 - 180 k (current limit to avoid trouble in the receiver)
  35. R7, R8 - 1 Megohm (filter for 50 Hz noise)
  36. R10 - 10 k pot ( or 50 or 100 or whatever)(offset since control signal
  37. is never zero)
  38. R11 - 27 k ( or whatever you need to get a nice full throttle travel)
  39. R13 - 2.2 k (or whatever you need to turn the MOSFET fully on)
  40. C1 - 0.033 uF (collects signal input and averages over severalpulses)
  41. C2 - 0.047 uF (filter with R8)
  42. C3 - 0.033 uF (part of ramp generator)
  43. D1, D2, D3 - 1N4148 ( small signal diodes try without D3 )
  44. Q1 - IRFZ40 MOSFET ( or any fet that can take 15 Amps and 15 volts with
  45. a low On resistance; IRFZ40 - 0.028 ohms, IRF540 - 0.085 ohms, IRFP064 - 0.009 ohms)
  46. Q2 - 2N4401 NPN transistor
  47. Q3 - 2N4403 PNP transistor
  48.  
  49.  
  50. Richard Haley
  51. -- 
  52. Richard  Haley                          haley@ee.ualberta.ca
  53. Electrical Engineering                  VE6AKF 
  54. University of Alberta 238 Civil Elect   Voice (403)492-2954
  55. Edmonton, Alberta, Canada               Fax   (403)492-1811
  56.