Piper's Pit BBS/FTP: ibm 0210

home *** CD-ROM | disk | FTP | other *** search

/ Piper's Pit BBS/FTP: ibm 0210 - 0219 / ibm0210-0219 / ibm0213.tar / ibm0213 / LS4APWAD.ZIP / LS40A.A12 / IBMLSA / IBM400R2 / OSLANAPI.ZIP / IBMLAN / NETSRC / H / ERRLOG.H < prev next >

Wrap

C/C++ Source or Header | 1994-06-10 | 34.9 KB | 1,054 lines

/**************************************************************************/ /* */ /* IBM OS/2(tm) Local Area Network (LAN) Server */ /* Version 3.0 */ /* (c) Copyright International Business Machines Corporation, 1988, 1992 */ /* */ /**************************************************************************/ /********************************************************************/ /******************************************************************** * * * About this file ... ERRLOG.H * * * * This file contains information about the NetErrorLog APIs. * * * * Function prototypes. * * * * Data structure templates. * * * * Definition of special values. * * * * * * NOTE: You must include NETCONS.H before this file, since this * * file depends on values defined in NETCONS.H. * * * ********************************************************************/ #ifdef INCL_32 #pragma pack(1) #endif #ifndef NETERRLOG_INCLUDED #define NETERRLOG_INCLUDED /**************************************************************** * * * Data Structures for LogRead * * * ****************************************************************/ #ifndef LOGFLAGS_FORWARD typedef struct loghandle { unsigned long time; /* Timestamp of first record */ unsigned long last_flags; /* Last call's flags */ unsigned long offset; /* Current byte offset in log */ unsigned long rec_offset; /* Current record offset in log */ } HLOG; #define LOGFLAGS_FORWARD 0 #define LOGFLAGS_BACKWARD 0x1 #define LOGFLAGS_SEEK 0x2 #endif /**************************************************************** * * * Function prototypes * * * ****************************************************************/ extern API_FUNCTION NetErrorLogClear ( const unsigned char LSFAR * pszServer, const unsigned char LSFAR * pszBackupFile, unsigned char LSFAR * pszReserved ); extern API_FUNCTION NetErrorLogOpen ( const unsigned char LSFAR * pszServer, unsigned LSFAR * phErrorLog, unsigned char LSFAR * pszReserved ); extern API_FUNCTION NetErrorLogRead ( const unsigned char LSFAR * pszServer, const unsigned char LSFAR * pszReserved1, HLOG LSFAR * phErrorLog, unsigned long ulOffset, unsigned short LSFAR * pusReserved2, unsigned long ulReserved3, unsigned long flOffset, unsigned char LSFAR * pbBuffer, unsigned short cbBuffer, unsigned short LSFAR * pcbReturned, unsigned short LSFAR * pcbTotalAvail ); extern API_FUNCTION NetErrorLogWrite ( unsigned char LSFAR * pszReserved1, unsigned short usCode, const unsigned char LSFAR * pszComponent, const unsigned char LSFAR * pbBuffer, unsigned short cbBuffer, const unsigned char LSFAR * pszStrBuf, unsigned short cStrBuf, unsigned char LSFAR * pszReserved2 ); /**************************************************************** * * * Data structure templates * * * ****************************************************************/ struct error_log { unsigned short el_len; unsigned short el_reserved; unsigned long el_time; unsigned short el_error; unsigned char el_name[SNLEN+1]; unsigned short el_data_offset; unsigned short el_nstrings; }; /* error_log */ /* -------------------- Begin F2359 --------------------- */ #ifdef PURE_32 /**************************************************************** * * * Function prototypes for "pure" 32-bit code * * * ****************************************************************/ extern API32_FUNCTION Net32ErrorLogClear ( const unsigned char * pszServer, const unsigned char * pszBackupFile, unsigned char * pszReserved ); extern API32_FUNCTION Net32ErrorLogRead ( const unsigned char * pszServer, const unsigned char * pszReserved1, HLOG * phErrorLogHandle, unsigned long ulOffset, unsigned short * pusReserved2, unsigned long ulReserved3, unsigned long ulOpenflags, unsigned char * pbBuffer, unsigned long ulBuffer, unsigned long * pulReturned, unsigned long * pulTotalAvail ); extern API32_FUNCTION Net32ErrorLogWrite ( unsigned char * pszReserved1, unsigned short usCode, const unsigned char * pszComponent, const unsigned char * pbBuffer, unsigned long ulBuffer, const unsigned char * pszStrBuf, unsigned short cStrBuf, unsigned char * pszReserved2 ); #endif /* PURE_32 */ /* -------------------- End F2359 --------------------- */ /**************************************************************** * * * Special values and constants * * * ****************************************************************/ #define ERRLOG_BASE 3100 /* NELOG errors start here */ /* * Generic (could be used by more than one service) * error log messages from 0 to 25 */ #define NELOG_Internal_Error (ERRLOG_BASE + 0) /* * The operation failed because a network software error occurred. */ #define NELOG_Resource_Shortage (ERRLOG_BASE + 1) /* * The system ran out of a resource controlled by the %1 option. */ #define NELOG_Unable_To_Lock_Segment (ERRLOG_BASE + 2) /* * The service failed to obtain a long-term lock on the * segment for NCBs. The error code is the data. */ #define NELOG_Unable_To_Unlock_Segment (ERRLOG_BASE + 3) /* * The service failed to release the long-term lock on the * segment for NCBs. The error code is the data. */ #define NELOG_Uninstall_Service (ERRLOG_BASE + 4) /* * There was an error stopping service %1. * The error code from NetServiceControl is the data. */ #define NELOG_Init_Exec_Fail (ERRLOG_BASE + 5) /* * Initialization failed because of an OS/2 exec failure on * path %1. The OS/2 error code is the data. */ #define NELOG_Ncb_Error (ERRLOG_BASE + 6) /* * An unexpected NCB was received. The NCB is the data. */ #define NELOG_Ioctl_Error (ERRLOG_BASE + 8) /* * A DosDevIoctl or DosFsCtl to NETWKSTA.SYS failed. * The data shown is in this format: * DWORD approx CS:IP of call to ioctl or fsctl * WORD error code * WORD ioctl or fsctl number */ #define NELOG_System_Semaphore (ERRLOG_BASE + 9) /* * Unable to create or open system semaphore %1. * The error code is the data. */ #define NELOG_Init_OpenCreate_Err (ERRLOG_BASE + 10) /* * Initialization failed because of an open/create error on the * file %1. The OS/2 error code is the data. */ #define NELOG_NetBios (ERRLOG_BASE + 11) /* * An unexpected NetBios error occurred. * The error code is the data. */ #define NELOG_SMB_Illegal (ERRLOG_BASE + 12) /* * An illegal SMB was received. * The SMB is the data. */ #define NELOG_Service_Fail (ERRLOG_BASE + 13) /* * Initialization failed because the requested service %1 * could not be started. */ #define NELOG_Entries_Lost (ERRLOG_BASE + 14) /* * Some entries in the error log were lost because of a buffer * overflow. */ /* * Server specific error log messages from 20 to 40 */ #define NELOG_Init_Seg_Overflow (ERRLOG_BASE + 20) /* * Initialization parameters controlling resource usage other * than net buffers are sized so that too much memory is needed. */ #define NELOG_Srv_No_Mem_Grow (ERRLOG_BASE + 21) /* * The server cannot increase the size of a memory segment. */ #define NELOG_Access_File_Bad (ERRLOG_BASE + 22) /* * Initialization failed because account file: %1 is either incorrect * or not present. */ #define NELOG_Srvnet_Not_Started (ERRLOG_BASE + 23) /* * Initialization failed because network: %1 was not started. */ #define NELOG_Init_Chardev_Err (ERRLOG_BASE + 24) /* * The server failed to start. Either all three chdev * parameters must be zero or all three must be nonzero. */ #define NELOG_Remote_API (ERRLOG_BASE + 25) /* A remote API request was halted due to the following * invalid description string: %1. */ #define NELOG_Ncb_TooManyErr (ERRLOG_BASE + 26) /* The network %1 ran out of NCBs. You may need to increase NCBs * for this network. The following information includes the * number of NCBs submitted by the server when this error occurred: */ #define NELOG_Mailslot_err (ERRLOG_BASE + 27) /* The server cannot create the %1 mailslot needed to send * the ReleaseMemory alert message. The error received is: */ #define NELOG_ReleaseMem_Alert (ERRLOG_BASE + 28) /* The server failed to register for the RELEASEMEMORY alert, * with recipient %1. The error code from * NetAlertStart is the data. */ #define NELOG_AT_cannot_write (ERRLOG_BASE + 29) /* The server cannot update the AT schedule file. The file * is corrupt. */ #define NELOG_Cant_Make_Msg_File (ERRLOG_BASE + 30) /* The server encountered an error when calling * NetIMakeLMFileName. The error code is the data. */ #define NELOG_Exec_Netservr_NoMem (ERRLOG_BASE + 31) /* Initialization failed because of an OS/2 exec failure on * path %1. There is not enough memory to start the process. * The OS/2 error code is the data. */ #define NELOG_Server_Lock_Failure (ERRLOG_BASE + 32) /* Longterm lock of server buffers failed. * Check swap disk free space and reboot system to start server. */ /* * Message service and POPUP specific error log messages from 40 to 55 */ #define NELOG_Msg_Shutdown (ERRLOG_BASE + 40) /* * The service has stopped due to repeated consecutive * occurrences of an NCB error. The last bad NCB follows * in raw data. */ #define NELOG_Msg_Sem_Shutdown (ERRLOG_BASE + 41) /* * The Message server has stopped due to a lock on the * Message server shared data segment. */ #define NELOG_Msg_Log_Err (ERRLOG_BASE + 50) /* * A file system error occurred while opening or writing to the * system message log file, %1. Message logging has been * switched off due to the error. The error code is the data. */ #define NELOG_VIO_POPUP_ERR (ERRLOG_BASE + 51) /* * Unable to display message POPUP due to OS/2 VIO call error. * The error code is the data. */ #define NELOG_Msg_Unexpected_SMB_Type (ERRLOG_BASE + 52) /* * An illegal SMB was received. The SMB is the data. */ /* * Requester specific error log messages from 60 to 75 */ #define NELOG_Wksta_Infoseg (ERRLOG_BASE + 60) /* * The workstation information segment is bigger than 64K bytes. * The size follows, in DWORD format: */ #define NELOG_Wksta_Compname (ERRLOG_BASE + 61) /* * The workstation was unable to get the name-number of computer name. */ #define NELOG_Wksta_BiosThreadFailure (ERRLOG_BASE + 62) /* * The workstation could not initialize the Async NetBios Thread. * The error code is the data. */ #define NELOG_Wksta_IniSeg (ERRLOG_BASE + 63) /* * The workstation could not open the initial shared segment. * The error code is the data. */ #define NELOG_Wksta_HostTab_Full (ERRLOG_BASE + 64) /* * The workstation host table is full. */ #define NELOG_Wksta_Bad_Mailslot_SMB (ERRLOG_BASE + 65) /* * A bad mailslot SMB was received. The SMB is the data. */ #define NELOG_Wksta_UASInit (ERRLOG_BASE + 66) /* * The workstation encountered an error while trying to start the UAS. * The error code is the data. */ #define NELOG_Wksta_SSIRelogon (ERRLOG_BASE + 67) /* * The workstation encountered an error while responding to an SSI revalidation request. * The function code and the error codes are the data. */ /* * Alerter service specific error log messages from 70 to 79 */ #define NELOG_Build_Name (ERRLOG_BASE + 70) /* * The Alerter service had a problem creating the list of * alert recipients. The error code is %1. */ #define NELOG_Name_Expansion (ERRLOG_BASE + 71) /* * There was an error expanding %1 as a group name. Try * splitting the group into two or more smaller groups. */ #define NELOG_Message_Send (ERRLOG_BASE + 72) /* * There was an error sending %2 the alert message - * ( * %3 ) * The error code is %1. */ #define NELOG_Mail_Slt_Err (ERRLOG_BASE + 73) /* * There was an error in creating or reading the alerter mailslot. * The error code is %1. */ #define NELOG_AT_cannot_read (ERRLOG_BASE + 74) /* * The server could not read the AT schedule file. */ #define NELOG_AT_sched_err (ERRLOG_BASE + 75) /* * The server found an invalid AT schedule record. */ #define NELOG_AT_schedule_file_created (ERRLOG_BASE + 76) /* * The server could not find an AT schedule file so it created one. */ #define NELOG_Srvnet_NB_Open (ERRLOG_BASE + 77) /* * The server could not access the %1 network with NetBiosOpen. */ #define NELOG_AT_Exec_Err (ERRLOG_BASE + 78) /* * The AT command processor couldn't run %1. */ /* * Cache Lazy Write and HPFS386 specific error log messages from 80 to 89 */ #define NELOG_Lazy_Write_Err (ERRLOG_BASE + 80) /* * WARNING: Because of a lazy-write error, drive %1 now * contains some corrupt data. The cache is stopped. */ #define NELOG_HotFix (ERRLOG_BASE + 81) /* * A defective sector on drive %1 has been replaced (hotfixed). * No data was lost. You should run CHKDSK soon to restore full * performance and replenish the volume's spare sector pool. * * The hotfix occurred while processing a remote request. */ #define NELOG_HardErr_From_Server (ERRLOG_BASE + 82) /* * A disk error occurred on the HPFS volume in drive %1. * The error occurred while processing a remote request. */ #define NELOG_SrvNoResource (ERRLOG_BASE + 86) /* * The server ran out of the following resource: %1 */ #define NELOG_BadSpareB (ERRLOG_BASE + 87) /* * A critical sector error was detected on drive %1. Back up the drive. No data was lost. */ #define NELOG_NoHotFix (ERRLOG_BASE + 88) /* * A bad sector on drive %1 cannot be fixed . Run CHKDSK /F on the drive. */ #define NELOG_BadVolume (ERRLOG_BASE + 89) /* * Drive %1 is experiencing severe disk errors. Back up the drive immediately. */ /* * NETWKSTA.SYS specific error log messages from 90 to 99 */ #define NELOG_NetWkSta_Internal_Error (ERRLOG_BASE + 90) /* * A NetWksta internal error has occurred: * %1 */ #define NELOG_NetWkSta_No_Resource (ERRLOG_BASE + 91) /* * The redirector is out of a resource: %1. */ #define NELOG_NetWkSta_SMB_Err (ERRLOG_BASE + 92) /* * An SMB error occurred on connection to %1. * The SMB header is the data. */ #define NELOG_NetWkSta_VC_Err (ERRLOG_BASE + 93) /* * A virtual circuit error occurred on the session to %1. * The NCB command and return code is the data. */ #define NELOG_NetWkSta_Stuck_VC_Err (ERRLOG_BASE + 94) /* * Hanging up a stuck session to %1. */ #define NELOG_NetWkSta_NCB_Err (ERRLOG_BASE + 95) /* * An NCB error occurred (%1). * The NCB is the data. */ #define NELOG_NetWkSta_Write_Behind_Err (ERRLOG_BASE + 96) /* * A write operation to %1 failed. * Data may have been lost. */ #define NELOG_NetWkSta_Reset_Err (ERRLOG_BASE + 97) /* * Reset of driver %1 failed to complete the NCB. * The NCB is the data. */ #define NELOG_NetWkSta_Too_Many (ERRLOG_BASE + 98) /* * The amount of resource %1 requested was more * than the maximum. The maximum amount was allocated. */ /* * Sideband specific error log messages from 99 to 101 */ #define NELOG_SB_Disabled (ERRLOG_BASE + 99) /* * Sideband transmissions have been disabled for the session * with server %1. */ #define NELOG_SB_Reenabled (ERRLOG_BASE + 100) /* * Sideband transmissions have been re-enabled for the session * with server %1. */ #define NELOG_SB_Not_Supported (ERRLOG_BASE + 101) /* * Sideband transmissions are not supported on %1 as defined in * IBMLAN.INI. */ /* * Spooler specific error log messages from 102 to 103 */ #define NELOG_Srv_Thread_Failure (ERRLOG_BASE + 104) /* * The server could not create a thread. * The THREADS parameter in CONFIG.SYS should be increased. */ #define NELOG_Srv_Close_Failure (ERRLOG_BASE + 105) /* * The server could not close %1. * The file is probably corrupt. */ #define NELOG_ReplUserCurDir (ERRLOG_BASE + 106) /* *The replicator cannot update directory %1. It has tree integrity * and is the current directory for some process. */ #define NELOG_ReplCannotMasterDir (ERRLOG_BASE + 107) /* *The server cannot export directory %1, to client %2. * It is exported from another server. */ #define NELOG_ReplUpdateError (ERRLOG_BASE + 108) /* *The replication server could not update directory %2 from the source *on %3 due to error %1. */ #define NELOG_ReplLostMaster (ERRLOG_BASE + 109) /* *Master %1 did not send an update notice for directory %2 at the expected * time. */ #define NELOG_NetlogonAuthDCFail (ERRLOG_BASE + 110) /* *Failed to authenticate with %2, the domain controller for domain %1. */ #define NELOG_ReplLogonFailed (ERRLOG_BASE + 111) /* *The replicator attempted to log on at %3 as %2 and failed. */ #define NELOG_ReplNetErr (ERRLOG_BASE + 112) /* * Network error %1 occurred. */ #define NELOG_ReplMaxFiles (ERRLOG_BASE + 113) /* * Replicator limit for files in a directory has been exceeded. */ #define NELOG_ReplMaxTreeDepth (ERRLOG_BASE + 114) /* * Replicator limit for tree depth has been exceeded. */ #define NELOG_ReplBadMsg (ERRLOG_BASE + 115) /* * Unrecognized message received in mailslot. */ #define NELOG_ReplSysErr (ERRLOG_BASE + 116) /* * System error %1 occurred. */ #define NELOG_ReplUserLoged (ERRLOG_BASE + 117) /* * Cannot log on. User is currently logged on and argument TRYUSER * is set to NO. */ #define NELOG_ReplBadImport (ERRLOG_BASE + 118) /* * IMPORT path %1 cannot be found. */ #define NELOG_ReplBadExport (ERRLOG_BASE + 119) /* * EXPORT path %1 cannot be found. */ #define NELOG_ReplSignalFileErr (ERRLOG_BASE + 120) /* * Replicator failed to update signal file in directory %2 due to * %1 system error. */ #define NELOG_DiskFT (ERRLOG_BASE+121) /* * Disk Fault Tolerance Error * *%1 */ #define NELOG_ReplAccessDenied (ERRLOG_BASE + 122) /* * Replicator could not access %2 * on %3 due to %1 system error. */ #define NELOG_NetlogonFailedPrimary (ERRLOG_BASE + 123) /* *The primary domain controller for domain %1 has apparently failed. */ #define NELOG_NetlogonPasswdSetFailed (ERRLOG_BASE + 124) /* * Error in changing this machine's password. */ #define NELOG_NetlogonTrackingError (ERRLOG_BASE + 125) /* *Error in updating the logon or logoff information for %1. */ #define NELOG_NetlogonSyncError (ERRLOG_BASE + 126) /* *Error in synchronizing with primary domain controller %1 */ #define NELOG_BadReplIniParm (ERRLOG_BASE + 127) /* * The replicator detected the following invalid parameter in * REPL.INI in subdirectory %1 : %2 */ #define NELOG_ReplUpdateACL (ERRLOG_BASE + 128) /* * The following error occured while updating the access control * profile for %1 */ /* * UPS service specific error log messages from 130 to 135 */ #define NELOG_UPS_PowerOut (ERRLOG_BASE + 130) /* * Power failure detected. */ #define NELOG_UPS_Shutdown (ERRLOG_BASE + 131) /* * The UPS service performed server shutdown. */ #define NELOG_UPS_CmdFileError (ERRLOG_BASE + 132) /* * The UPS service did not complete execution of the * user specified shutdown command file. */ #define NELOG_UPS_CannotOpenDriver (ERRLOG_BASE+133) /* The UPS driver could not be opened. The error code is * the data. */ #define NELOG_UPS_LowBattery (ERRLOG_BASE + 134) /* * Low battery detected. */ /* * HPFS386 'Out of Resource' messages from 135 to 143 * */ #define NELOG_R0SV_NO_RAM_WORKBUF (ERRLOG_BASE + 135) /* * RAM for 64Kb work buffer */ #define NELOG_R0SV_NO_RAM_HEAP (ERRLOG_BASE + 136) /* * RAM for heap expansion */ #define NELOG_R0SV_NO_RAM_HANDLE_TBL (ERRLOG_BASE + 137) /* * RAM for file handle table growth */ #define NELOG_R0SV_NO_CONNECTIONS (ERRLOG_BASE + 138) /* * LAN connections */ #define NELOG_R0SV_NO_OPEN_FILE_HANDLES (ERRLOG_BASE + 139) /* * Open file handles */ #define NELOG_R0SV_NO_SEARCH_HANDLES (ERRLOG_BASE + 140) /* * Search handles */ #define NELOG_R0SV_NO_FIND_HANDLES (ERRLOG_BASE + 141) /* * Find handles */ #define NELOG_R0SV_NO_WORKBUF (ERRLOG_BASE + 142) /* * 64Kb work buffers */ #define NELOG_R0SV_NO_HEAP (ERRLOG_BASE + 143) /* * Heap space */ #define NELOG_R0SV_NO_RAM_RABUF (ERRLOG_BASE + 144) /* * RAM for 64KB read-ahead buffer */ /* * Multimedia, Isochronous LAN and Bandwidth Management from 145 to 149 */ #define NELOG_BM_GenFailure (ERRLOG_BASE + 145) /* * A bandwidth management error occurred. The error is the data %1. */ #define NELOG_BM_SessFailure (ERRLOG_BASE +146) /* * A bandwidth management error occurred on the session to %1. * The error is the data %2. */ #define NELOG_R0SV_NO_RABUF (ERRLOG_BASE + 147) /* * 64KB read-ahead buffers */ /* * Remote boot server specific error log messages are from 150 to 164 */ #define NELOG_Missing_Parameter (ERRLOG_BASE + 150) /* * Initialization failed because of an invalid or missing * parameter in IBMLAN.INI: %1. */ #define NELOG_Invalid_Config_Line (ERRLOG_BASE + 151) /* * Initialization failed because of an invalid line in the * configuration file %1. The invalid line is the data. */ #define NELOG_Invalid_Config_File (ERRLOG_BASE + 152) /* * Initialization failed because of an error in the configuration * file %1. */ #define NELOG_File_Changed (ERRLOG_BASE + 153) /* * The file %1 has been changed after initialization. * The boot block loading was temporarily terminated. */ #define NELOG_Files_Dont_Fit (ERRLOG_BASE + 154) /* * The files do not fit to the 'boot' block configuration * file %1. Change BASE and ORG definitions or the order * of the files. */ #define NELOG_Wrong_DLL_Version (ERRLOG_BASE + 155) /* * Initialization failed because the dynamic link * library %1 returned a wrong version number. */ #define NELOG_Error_in_DLL (ERRLOG_BASE + 156) /* * There was an unrecoverable error in the dynamic * link library of the service. */ #define NELOG_System_Error (ERRLOG_BASE + 157) /* * The system returned an unexpected error code. * The error code is the data. */ #define NELOG_FT_ErrLog_Too_Large (ERRLOG_BASE + 158) /* * The fault-tolerance error log file, LANROOT\LOGS\FT.LOG * is more than 64K. */ #define NELOG_FT_Update_In_Progress (ERRLOG_BASE + 159) /* * The fault-tolerance error-log file, LANROOT\LOGS\FT.LOG, had the * update in progress bit set upon opening, which means that the * system crashed while working on the errorlog. */ #define NELOG_DCDBChecksumError (ERRLOG_BASE+165) /* * A checksum error occurred when accessing the domain control * database file %1. */ #define NELOG_DCDBIOError (ERRLOG_BASE+166) /* * An error occurred when reading from or writing to the * domain control database file %1. */ #define NELOG_DCDBFileNotFound (ERRLOG_BASE+167) /* * The domain control database file %1 was not found. */ #define NELOG_DirAlerts_Threshold (ERRLOG_BASE+168) /* * The write operation was successful, but the size of directory %1 * crossed a threshold. The remaining space in the directory is %2 KB. * * (%1 is the directory name) */ #define NELOG_DirAlerts_DirFull (ERRLOG_BASE+169) /* * There was not enough space within directory %1 to perform a write * operation. * * (%1 is the directory name) */ #define NELOG_DirAlerts_FatalError (ERRLOG_BASE+170) /* * The server encountered an error while initializing internal * data structures. The server uses these structures to process * alerts that pertain to directory limits. The server will not post * alerts. The OS/2 return code is %1. */ #define NELOG_DirAlerts_IniFailure (ERRLOG_BASE+171) /* * The server encountered an error while initializing internal * data structures. The server uses these structures to process * alerts that pertain to directory limits. The server will now * use its own default values. The INI file in use is %1. The * return code is %2. */ #define NELOG_DirAlerts_NoAlerts (ERRLOG_BASE+172) /* * An error occurred as the server attempted to send a message * concerning a directory limit. No message was sent. The OS/2 * return code is %1. */ #define NELOG_DlimNoHeap (ERRLOG_BASE+173) /* * The 386 HPFS server failed to enable directory limits on drive * %1 because of insufficient heap space. The drive is still * operational. */ #define NELOG_DlimDskErr (ERRLOG_BASE+174) /* * The 386 HPFS server failed to enable directory limits * on drive %1 because of a disk error. The drive is still * operational. */ #define NELOG_DirAlerts_BadIniParm (ERRLOG_BASE+175) /* * The server detected a parameterin the INI file %1 that is not * valid. The parameter is: %2. */ #define NELOG_DirAlerts_BadIniSyntax (ERRLOG_BASE+176) /* * The server detected a parameter in the INI file %1 that does * not have a valid syntax. The parameter is %2. */ #define NELOG_DirAlerts_BadDrive (ERRLOG_BASE+177) /* * The server detected and ignored a drive letter that is not valid * within a parameter in the INI file %1. The parameter is %2. */ /**************************************************************** * Microsoft has created a generic error log entry for OEMs to use to * log errors from OEM value added services. The code, which is the * 2nd arg to NetErrorLogWrite, is 3299. This value is manifest in * NET/H/ERRLOG.H as NELOG_OEM_Code. The text for error log entry * NELOG_OEM_Code is: "%1 %2 %3 %4 %5 %6 %7 %8 %9.". * * Microsoft suggests that OEMs use the insertion strings as follows: * %1: OEM System Name (e.g. 3+Open) * %2: OEM Service Name (e.g. 3+Mail) * %3: Severity level (e.g. error, warning, etc.) * %4: OEM error log entry sub-identifier (e.g. error code #) * %5 - % 9: Text. * * The call to NetErrorWrite must set nstrings = 9, and provide 9 * ASCIIZ strings. If the caller does not have 9 insertion strings, * provide null strings for the empty insertion strings. ****************************************************************/ #define NELOG_OEM_Code (ERRLOG_BASE + 199) /* * %1 %2 %3 %4 %5 %6 %7 %8 %9. */ #endif /* NETERRLOG_INCLUDED */ #if defined(INCL_32) || defined(MIXED_32) #pragma linkage (NetErrorLogClear, far16 pascal) #pragma linkage (NetErrorLogOpen, far16 pascal) #pragma linkage (NetErrorLogRead, far16 pascal) #pragma linkage (NetErrorLogWrite, far16 pascal) #pragma pack() #endif