Whiteline: Alpha/Whiteline Alpha.iso/linux/atari/source/source.lzh/atari-linux-0.01pl3/drivers/scsi/atari_NCR5380.c

C/C++ Source or Header | 1994-06-11 | 84.1 KB | 2,791 lines

/*
 * NCR 5380 generic driver routines.  These should make it *trivial*
 *     to implement 5380 SCSI drivers under Linux with a non-trantor
 *    architecture.
 *
 *    Note that these routines also work with NR53c400 family chips.
 *
 * Copyright 1993, Drew Eckhardt
 *    Visionary Computing
 *    (Unix and Linux consulting and custom programming)
 *     [e-mail]
 *    [phone]
 *
 * DISTRIBUTION REALEASE 4.
 *
 * For more information, please consult
 *
 * NCR 5380 Family
 * SCSI Protocol Controller
 * Databook
 *
 * NCR Microelectronics
 * 1635 Aeroplaza Drive
 * Colorado Springs, CO 80916
 * 1+ [phone]
 * 1+ [phone]
 */

/*
 * ++roman: To port the 5380 driver to the Atari, I had to do some changes in
 * this file, too:
 *
 *  - Some of the debug statements were incorrect (undefined variables and the
 *    like). I fixed that.
 *
 *  - In information_transfer(), I think a #ifdef was wrong. Looking at the
 *    possible DMA transfer size should also happen for REAL_DMA. I added this
 *    in the #if statement.
 *
 *  - When using real DMA, information_transfer() should return in a DATAOUT
 *    phase after starting the DMA. It has nothing more to do.
 *
 *  - The interrupt service routine should run main after end of DMA, too (not
 *    only after RESELECTION interrupts). Additionally, it should _not_ test
 *    for more interrupts after running main, since a DMA process may have
 *    been started and interrupts are turned on now. The new int could happen
 *    inside the execution of NCR5380_intr(), leading to recursive
 *    calls.
 *
 *  - I've added a function merge_consecutive_buffers() that trys to
 *    merge scatter-gather buffers that are located at consecutive
 *    physical addresses and can be processed with the same DMA setup.
 *    Since most scatter-gather operations work on a page (4K) of
 *    4 buffers (1K), in more than 90% of all cases three interrupts and
 *    DMA setup actions are saved.
 *
 */



/*
 * $Log: NCR5380.c,v $
 * Revision 1.5  1994/01/19  09:14:57  drew
 * Fixed udelay() hack that was being used on DATAOUT phases
 * instead of a propper wait for the final handshake.
 *
 * Revision 1.4  1994/01/19  06:44:25  drew
 * *** empty log message ***
 *
 * Revision 1.3  1994/01/19  05:24:40  drew
 * Added support for TCR LAST_BYTE_SENT bit.
 *
 * Revision 1.2  1994/01/15  06:14:11  drew
 * REAL DMA support, bug fixes.
 *
 * Revision 1.1  1994/01/15  06:00:54  drew
 * Initial revision
 *
 */

/*
 * Furthur development / testing that should be done :
 * 1.  Cleanup the NCR5380_transfer_dma function and DMA operation complete
 *     code so that everything does the same thing that's done at the
 *     end of a pseudo-DMA read operation.
 *
 * 2.  Fix REAL_DMA (interrupt driven, polled works fine) -
 *     basically, transfer size needs to be reduced by one
 *     and the last byte read as is done with PSEUDO_DMA.
 *
 * 3.  Test USLEEP code
 *
 * 4.  Test SCSI-II tagged queueing (I have no devices which support
 *    tagged queueing)
 *
 * 5.  Test linked command handling code after Eric is ready with
 *      the high level code.
 */

#ifndef notyet
#undef LINKED
#undef USLEEP
/* #undef REAL_DMA */
#endif

#ifdef REAL_DMA_POLL
#undef READ_OVERRUNS
#define READ_OVERRUNS
#endif

/*
 * Design
 * Issues :
 *
 * The other Linux SCSI drivers were written when Linux was Intel PC-only,
 * and specifically for each board rather than each chip.  This makes their
 * adaptation to platforms like the Mac (Some of which use NCR5380's)
 * more difficult than it has to be.
 *
 * Also, many of the SCSI drivers were written before the command queing
 * routines were implemented, meaning their implementations of queued
 * commands were hacked on rather than designed in from the start.
 *
 * When I designed the Linux SCSI drivers I figured that
 * while having two different SCSI boards in a system might be useful
 * for debugging things, two of the same type wouldn't be used.
 * Well, I was wrong and a number of users have mailed me about running
 * multiple high-performance SCSI boards in a server.
 *
 * Finally, when I get questions from users, I have no idea what
 * revision of my driver they are running.
 *
 * This driver attempts to address these problems :
 * This is a generic 5380 driver.  To use it on a different platform,
 * one simply writes appropriate system specific macros (ie, data
 * transfer - some PC's will use the I/O bus, 68K's must use
 * memory mapped) and drops this file in their 'C' wrapper.
 *
 * As far as command queueing, two queues are maintained for
 * each 5380 in the system - commands that haven't been issued yet,
 * and commands that are currently executing.  This means that an
 * unlimited number of commands may be queued, letting
 * more commands propogate from the higher driver levels giving higher
 * througput.  Note that both I_T_L and I_T_L_Q nexuses are supported,
 * allowing multiple commands to propogate all the way to a SCSI-II device
 * while a command is allready executing.
 *
 * To solve the multiple-boards-in-the-same-system problem,
 * there is a separate instance structure for each instance
 * of a 5380 in the system.  So, mutliple NCR5380 drivers will
 * be able to coexist with appropriate changes to the high level
 * SCSI code.
 *
 * A NCR5380_PUBLIC_REVISION macro is provided, with the release
 * number (updated for each public release) printed by the
 * NCR5380_print_options command, which should be called from the
 * wrapper detect function, so that I know what release of the driver
 * users are using.
 *
 * Issues specific to the NCR5380 :
 *
 * When used in a PIO or pseudo-dma mode, the NCR5380 is a braindead
 * piece of hardware that requires you to sit in a loop polling for
 * the REQ signal as long as you are connected.  Some devices are
 * brain dead (ie, many TEXEL CD ROM drives) and won't disconnect
 * while doing long seek operations.
 *
 * The workarround for this is to keep track of devices that have
 * disconnected.  If the device hasn't disconnected, for commands that
 * should disconnect, we do something like
 *
 * while (!REQ is asserted) { sleep for N usecs; poll for M usecs }
 *
 * Some tweaking of N and M needs to be done.  An algorithm based
 * on "time to data" would give the best results as long as short time
 * to datas (ie, on the same track) were considered, however these
 * broken devices are the exception rather than the rule and I'd rather
 * spend my time optomizing for the normal case.
 *
 * Architecture :
 *
 * At the heart of the design is a corroutine, NCR5380_main,
 * which is started when not running by the interrupt handler,
 * timer, and queue command function.  It attempts to establish
 * I_T_L or I_T_L_Q nexuses by removing the commands from the
 * issue queue and calling NCR5380_select() if a nexus
 * is not established.
 *
 * Once a nexus is established, the NCR5380_information_transfer()
 * phase goes through the various phases as instructed by the target.
 * if the target goes into MSG IN and sends a DISCONNECT message,
 * the command structure is placed into the per instance disconnected
 * queue, and NCR5380_main tries to find more work.  If USLEEP
 * was defined, and the target is idle for too long, the system
 * will try to sleep.
 *
 * If a command has disconnected, eventually an interrupt will trigger,
 * calling NCR5380_intr()  which will inturn call NCR5380_reselect
 * to restablish a nexus.  This will run main if necessary.
 *
 * On command termination, the done function will be called as
 * appropriate.
 *
 * SCSI pointers are maintained in the SCp field of SCSI command
 * structures, being initialized after the command is connected
 * in NCR5380_select, and set as appropriate in NCR5380_information_transfer.
 * Note that in violation of the standard, an implicit SAVE POINTERS operation
 * is done, since some BROKEN disks fail to issue an explicit SAVE POINTERS.
 */

/*
 * Using this file :
 * This file a skeleton Linux SCSI driver for the NCR 5380 series
 * of chips.  To use it, you write a architecture specific functions
 * and macros and include this file in your driver.
 *
 * These macros control options :
 * AUTOPROBE_IRQ - if defined, the NCR5380_probe_irq() function will be
 *    defined.
 *
 * AUTOSENSE - if defined, REQUEST SENSE will be performed automatically
 *    for commands that return with a CHECK CONDITION status.
 *
 * DIFFERENTIAL - if defined, NCR53c81 chips will use external differential
 *     tracievers.
 *
 * LINKED - if defined, linked commands are supported.
 *
 * PSEUDO_DMA - if defined, PSEUDO DMA is used during the data transfer phases.
 *
 * REAL_DMA - if defined, REAL DMA is used during the data transfer phases.
 *
 * REAL_DMA_POLL - if defined, REAL DMA is used but the driver doesn't
 *     rely on phase mismatch and EOP interrupts to determine end
 *    of phase.
 *
 * SCSI2 - if defined, SCSI-2 tagged queing is used where possible
 *
 * UNSAFE - leave interrupts enabled during pseudo-DMA transfers.  You
 *        only really want to use this if you're having a problem with
 *        dropped characters during high speed communications, and even
 *        then, you're going to be better off twiddling with transfersize
 *        in the high level code.
 *
 * USLEEP - if defined, on devices that aren't disconnecting from the
 *    bus, we will go to sleep so that the CPU can get real work done
 *    when we run a command that won't complete immediately.
 *
 * Note that if USLEEP is defined, NCR5380_TIMER *must* also be
 * defined.
 *
 * Defaults for these will be provided if USLEEP is defined, although
 * the user may want to adjust these to allocate CPU resources to
 * the SCSI driver or "real" code.
 *
 * USLEEP_SLEEP - amount of time, in jiffies, to sleep
 *
 * USLEEP_POLL - amount of time, in jiffies, to poll
 *
 * These macros MUST be defined :
 * NCR5380_local_declare() - declare any local variables needed for your transfer
 *    routines.
 *
 * NCR5380_setup(instance) - initialize any local variables needed from a given
 *    instance of the host adapter for NCR5380_{read,write,pread,pwrite}
 *
 * NCR5380_read(register)  - read from the specified register
 *
 * NCR5380_write(register, value) - write to the specific register
 *
 * NCR5380_implementation_fields  - additional fields needed for this
 *    specific implementation of the NCR5380
 *
 * Either real DMA *or* pseudo DMA may be implemented
 * REAL functions :
 * NCR5380_REAL_DMA should be defined if real DMA is to be used.
 * Note that the DMA setup functions should return the number of bytes
 *    that they were able to program the controller for.
 *
 * Also note that generic i386/PC versions of these macros are
 *    available as NCR5380_i386_dma_write_setup,
 *    NCR5380_i386_dma_read_setup, and NCR5380_i386_dma_residual.
 *
 * NCR5380_dma_write_setup(instance, src, count) - initialize
 * NCR5380_dma_read_setup(instance, dst, count) - initialize
 * NCR5380_dma_residual(instance); - residual count
 *
 * PSEUDO functions :
 * NCR5380_pwrite(instance, src, count)
 * NCR5380_pread(instance, dst, count);
 *
 * If nothing specific to this implementation needs doing (ie, with external
 * hardware), you must also define
 *
 * NCR5380_queue_command
 * NCR5380_reset
 * NCR5380_abort
 *
 * to be the global entry points into the specific driver, ie
 * #define NCR5380_queue_command t128_queue_command.
 *
 * If this is not done, the routines will be defined as static functions
 * with the NCR5380* names and the user must provide a globally
 * accessable wrapper function.
 *
 * The generic driver is initialized by calling NCR5380_init(instance),
 * after setting the appropriate host specific fields and ID.  If the
 * driver wishes to autoprobe for an IRQ line, the NCR5380_probe_irq(instance,
 * possible) function may be used.  Before the specific driver initialization
 * code finishes, NCR5380_print_options should be called.
 */

static struct Scsi_Host *first_instance = NULL;
static Scsi_Host_Template *the_template = NULL;

/*
 * Function: void merge_consecutive_buffers( Scsi_Cmnd *cmd )
 *
 * Purpose: Try to merge several scatter-gather requests into one DMA
 *    transfer. This is possible if the scatter buffers lie on
 *    physical consecutive addresses.
 *
 * Parameters: Scsi_Cmnd *cmd
 *    The command to work on. The first scatter buffer's data are
 *    assumed to be already transfered into ptr/this_residual.
 */

/* A special issue is when the buffer is exactly at the end of the
 * last physical memory chunk: VTOP would have to calculate the
 * physical address just 1 byte behind the end of physical memory. But
 * it will panic if given this address :-( So we need to avoid calling
 * VTOP on addresses that don't exist. This is done by keeping
 * 'endadr' to be the real end address of the buffer, not one byte
 * more (which would be easier).
 */

static void merge_consecutive_buffers( Scsi_Cmnd *cmd )

{
    unsigned long endadr;
#if (NDEBUG & NDEBUG_MERGING)
    unsigned long oldlen = cmd->SCp.this_residual;
    int          cnt = 1;
#endif

    for( endadr = VTOP(cmd->SCp.ptr + cmd->SCp.this_residual - 1);
     cmd->SCp.buffers_residual &&
     /* Note that, if READ_OVERRUNS is defined, the virtual
      * addresses have to be consecutive, too. The last two bytes
      * are done by PIO and that uses virtual addresses.
      */
#ifdef READ_OVERRUNS
     (cmd->SCp.buffer+1)->address ==
         cmd->SCp.ptr + cmd->SCp.this_residual &&
#endif
     VTOP( (cmd->SCp.buffer+1)->address ) == endadr + 1; ) {

#if (NDEBUG & NDEBUG_MERGING)
    printk( "%08lx == %08lx -> merging\n",
        VTOP( (cmd->SCp.buffer+1)->address ), endadr );
    ++cnt;
#endif
    ++cmd->SCp.buffer;
    --cmd->SCp.buffers_residual;
    cmd->SCp.this_residual += cmd->SCp.buffer->length;
    endadr += cmd->SCp.buffer->length;
    }
#if (NDEBUG & NDEBUG_MERGING)
    if (oldlen != cmd->SCp.this_residual)
    printk( "merged %d buffers from %08lx, new length %08lx\n",
        cnt, (long)(cmd->SCp.ptr), cmd->SCp.this_residual );
#endif
}

/*
 * Function : void initialize_SCp(Scsi_Cmnd *cmd)
 *
 * Purpose : initialize the saved data pointers for cmd to point to the
 *    start of the buffer.
 *
 * Inputs : cmd - Scsi_Cmnd structure to have pointers reset.
 */

static __inline__ void initialize_SCp(Scsi_Cmnd *cmd) {
    /*
     * Initialize the Scsi Pointer field so that all of the commands in the
     * various queues are valid.
     */

    if (cmd->use_sg) {
    cmd->SCp.buffer = (struct scatterlist *) cmd->buffer;
    cmd->SCp.buffers_residual = cmd->use_sg - 1;
    cmd->SCp.ptr = (char *) cmd->SCp.buffer->address;
    cmd->SCp.this_residual = cmd->SCp.buffer->length;
    /* ++roman: Try to merge some scatter-buffers if they are at
     * consecutive physical addresses.
     */
    merge_consecutive_buffers( cmd );
    } else {
    cmd->SCp.buffer = NULL;
    cmd->SCp.buffers_residual = 0;
    cmd->SCp.ptr = (char *) cmd->request_buffer;
    cmd->SCp.this_residual = cmd->request_bufflen;
    }
}

#include <linux/delay.h>

#ifdef NDEBUG
static struct {
    unsigned char mask;
    char * name;}
signals[] = {{ SR_DBP, "PARITY"}, { SR_RST, "RST" }, { SR_BSY, "BSY" },
    { SR_REQ, "REQ" }, { SR_MSG, "MSG" }, { SR_CD,  "CD" }, { SR_IO, "IO" },
    { SR_SEL, "SEL" }, {0, NULL}},
basrs[] = {{BASR_ATN, "ATN"}, {BASR_ACK, "ACK"}, {0, NULL}},
icrs[] = {{ICR_ASSERT_RST, "ASSERT RST"},{ICR_ASSERT_ACK, "ASSERT ACK"},
    {ICR_ASSERT_BSY, "ASSERT BSY"}, {ICR_ASSERT_SEL, "ASSERT SEL"},
    {ICR_ASSERT_ATN, "ASSERT ATN"}, {ICR_ASSERT_DATA, "ASSERT DATA"},
    {0, NULL}},
mrs[] = {{MR_BLOCK_DMA_MODE, "MODE BLOCK DMA"}, {MR_TARGET, "MODE TARGET"},
    {MR_ENABLE_PAR_CHECK, "MODE PARITY CHECK"}, {MR_ENABLE_PAR_INTR,
    "MODE PARITY INTR"}, {MR_ENABLE_EOP_INTR,"MODE EOP INTR"},
    {MR_MONITOR_BSY, "MODE MONITOR BSY"},
    {MR_DMA_MODE, "MODE DMA"}, {MR_ARBITRATE, "MODE ARBITRATION"},
    {0, NULL}};

/*
 * Function : void NCR5380_print(struct Scsi_Host *instance)
 *
 * Purpose : print the SCSI bus signals for debugging purposes
 *
 * Input : instance - which NCR5380
 */

static void NCR5380_print(struct Scsi_Host *instance) {
    NCR5380_local_declare();
    unsigned char status, data, basr, mr, icr, i;
    NCR5380_setup(instance);
    cli();
    data = NCR5380_read(CURRENT_SCSI_DATA_REG);
    status = NCR5380_read(STATUS_REG);
    mr = NCR5380_read(MODE_REG);
    icr = NCR5380_read(INITIATOR_COMMAND_REG);
    basr = NCR5380_read(BUS_AND_STATUS_REG);
    sti();
    for (i = 0; signals[i].mask ; ++i)
    if (status & signals[i].mask)
        printk(" %s", signals[i].name);
    for (i = 0; basrs[i].mask ; ++i)
    if (basr & basrs[i].mask)
        printk(" %s", basrs[i].name);
    for (i = 0; icrs[i].mask; ++i)
    if (icr & icrs[i].mask)
        printk(" %s", icrs[i].name);
    for (i = 0; mrs[i].mask; ++i)
    if (mr & mrs[i].mask)
        printk(" %s", mrs[i].name);
    printk("\n");
}

static struct {
    unsigned char value;
    char *name;
} phases[] = {
    {PHASE_DATAOUT, "DATAOUT"}, {PHASE_DATAIN, "DATAIN"}, {PHASE_CMDOUT, "CMDOUT"},
    {PHASE_STATIN, "STATIN"}, {PHASE_MSGOUT, "MSGOUT"}, {PHASE_MSGIN, "MSGIN"},
    {PHASE_UNKNOWN, "UNKNOWN"}};

/*
 * Function : void NCR5380_print_phase(struct Scsi_Host *instance)
 *
 * Purpose : print the current SCSI phase for debugging purposes
 *
 * Input : instance - which NCR5380
 */

static void NCR5380_print_phase(struct Scsi_Host *instance)

{
    NCR5380_local_declare();
    unsigned char status;
    int i;
    NCR5380_setup(instance);

    status = NCR5380_read(STATUS_REG);
    if (!(status & SR_REQ))
    printk("scsi%d : REQ not asserted, phase unknown.\n",
        instance->host_no);
    else {
    for (i = 0; (phases[i].value != PHASE_UNKNOWN) &&
        (phases[i].value != (status & PHASE_MASK)); ++i);
    printk("scsi%d : phase %s\n", instance->host_no, phases[i].name);
    }
}
#endif

/*
 * We need to have our corroutine active given these constraints :
 * 1.  The mutex flag, main_running, can only be set when the main
 *     routine can actually process data, otherwise SCSI commands
 *     will never get issued.
 *
 * 2.  NCR5380_main() shouldn't be called before it has exited, because
 *     other drivers have had kernel stack overflows in similar
 *     situations.
 *
 * 3.  We don't want to inline NCR5380_main() because of space concerns,
 *     even though it is only called in two places.
 *
 * So, the solution is to set the mutex in an inline wrapper for the
 * main corroutine, and have the main corroutine exit with interrupts
 * disabled after the final search through the queues so that no race
 * conditions are possible.
 */

static volatile int main_running = 0;

/*
 * Function : run_main(void)
 *
 * Purpose : insure that the coroutine is running and will process our
 *     request.  main_running is checked/set here (in an inline function)
 *    rather than in NCR5380_main itself to reduce the chances of stack
 *    overflow.
 *
 */

static __inline__ void run_main(void)

{
/*    unsigned long flags; */

/*    save_flags(flags); */
    cli();
    if (!main_running) {
    main_running = 1;
        NCR5380_main();
    /*
         * main_running is cleared in NCR5380_main once it can't do
     * more work, and NCR5380_main exits with interrupts disabled.
     */
    /* restore_flags(flags); */
    sti();
    } else {
    /* restore_flags(flags); */
    sti();
    }
}

#ifdef USLEEP
#ifndef NCR5380_TIMER
#error "NCR5380_TIMER must be defined so that this type of NCR5380 driver gets a unique timer."
#endif

/*
 * These need tweaking, and would probably work best as per-device
 * flags initialized differently for disk, tape, cd, etc devices.
 * People with broken devices are free to experiment as to what gives
 * the best results for them.
 *
 * USLEEP_SLEEP should be a minimum seek time.
 *
 * USLEEP_POLL should be a maximum rotational latency.
 */
#ifndef USLEEP_SLEEP
/* 20 ms (reasonable hard disk speed) */
#define USLEEP_SLEEP 2
#endif
/* 300 RPM (floppy speed) */
#ifndef USLEEP_POLL
#define USLEEP_POLL 20
#endif

static struct Scsi_Host * expires_first = NULL;

/*
 * Function : int should_disconnect (unsigned char cmd)
 *
 * Purpose : decide weather a commmand would normally disconnect or
 *    not, since if it won't disconnect we should go to sleep.
 *
 * Input : cmd - opcode of SCSI command
 *
 * Returns : DISCONNECT_LONG if we should disconnect for a really long
 *     time (ie always, sleep, look for REQ active, sleep),
 *    DISCONNECT_TIME_TO_DATA if we would only disconnect for a normal
 *     time-to-data dealy, DISCONNECT_NONE if this command would return
 *     immediately.
 *
 *      Future sleep algorithms based on time to data can exploit
 *      something like this so they can differentiate between "normal"
 *    (ie, read, write, seek) and unusual commands (ie, * format).
 *
 * Note : We don't deal with commands that handle an immediate disconnect,
 *
 */

static int should_disconnect (unsigned char cmd)

{
    switch (cmd) {
    case READ_6:
    case WRITE_6:
    case SEEK_6:
    case READ_10:
    case WRITE_10:
    case SEEK_10:
    return DISCONNECT_TIME_TO_DATA;
    case FORMAT_UNIT:
    case SEARCH_HIGH:
    case SEARCH_LOW:
    case SEARCH_EQUAL:
    return DISCONNECT_LONG;
    default:
    return DISCONNECT_NONE;
    }
}

/*
 * Assumes instance->time_expires has been set in higher level code.
 */

static int NCR5380_set_timer (struct Scsi_Host *instance)

{
    struct Scsi_Host *tmp, **prev;

    cli();
    if (((struct NCR5380_hostdata *) (instance->host_data))->next_timer) {
    sti();
    return -1;
    }

    for (prev = &expires_first, tmp = expires_first; tmp;
    prev = &(((struct NCR5380_hostdata *) tmp->host_data)->next_timer),
    tmp = ((struct NCR5380_hostdata *) tmp->host_data)->next_timer)
    if (instance->time_expires < tmp->time_expires)
        break;

    instance->next_timer = tmp;
    *prev = instance;
    timer_table[NCR5380_TIMER].expires = expires_first->time_expires;
    timer_active |= 1 << NCR5380_TIMER;
    sti;
    return 0;
}

/* Doing something about unwanted rentrancy here might be useful */
void NCR5380_timer_fn(void)

{
    struct Scsi_Host *instance;
    cli();
    for (; expires_first && expires_first->time_expires >= jiffies; ) {
    instance = ((NCR5380_hostdata *) expires_first->host_data)->
        expires_next;
    ((NCR5380_hostdata *) expires_first->host_data)->expires_next =
        NULL;
    ((NCR5380_hostdata *) expires_first->host_data)->time_expires =
        0;
    expires_first = instance;
    }

    if (expires_first) {
    timer_table[NCR5380_TIMER].expires = ((NCR5380_hostdata *)
        expires_first->host_data)->time_expires;
    timer_active |= (1 << NCR5380_TIMER);
    } else {
    timer_table[NCR5380_TIMER].expires = 0;
    timer_active &= ~(1 << MCR5380_TIMER);
    }
    sti();

    run_main();
}
#endif /* def USLEEP */

static void NCR5380_all_init (void)

{
    static int done = 0;
    if (!done) {
#if (NDEBUG & NDEBUG_INIT)
    printk("scsi : NCR5380_all_init()\n");
#endif
    done = 1;
#ifdef USLEEP
    timer_table[NCR5380_TIMER].expires = 0;
    timer_table[NCR5380_TIMER].fn = NCR5380_timer_fn;
#endif
    }
}

#ifdef AUTOPROBE_IRQ
/*
 * Function : int NCR5380_probe_irq (struct Scsi_Host *instance, int possible)
 *
 * Purpose : autoprobe for the IRQ line used by the NCR5380.
 *
 * Inputs : instance - pointer to this instance of the NCR5380 driver,
 *          possible - bitmask of permissable interrupts.
 *
 * Returns : number of the IRQ selected, IRQ_NONE if no interrupt fired.
 *
 * XXX no effort is made to deal with spurious interrupts.
 */


static int probe_irq;
static void probe_intr (int sig)

{
    probe_irq = sig;
};
static struct sigaction probe_sigaction = { probe_intr, 0, SA_INTERRUPT,
    NULL};

static int NCR5380_probe_irq (struct Scsi_Host *instance, int possible)

{
    NCR5380_local_declare();
    struct NCR5380_hostdata *hostdata = (struct NCR5380_hostdata *)
     instance->hostdata;
    unsigned long timeout;
    int trying_irqs, i, mask;
    NCR5380_setup(instance);

    for (trying_irqs = i = 0, mask = 1; i < 16; ++i, mask <<= 1)
    if ((mask & possible) &&  (irqaction (i, &probe_sigaction)
        == 0))
        trying_irqs |= mask;

    timeout = jiffies + 25;
    probe_irq = IRQ_NONE;

/*
 * A interrupt is triggered whenever BSY = false, SEL = true
 * and a bit set in the SELECT_ENABLE_REG is asserted on the
 * SCSI bus.
 *
 * Note that the bus is only driven when the phase control signals
 * (I/O, C/D, and MSG) match those in the TCR, so we must reset that
 * to zero.
 */

    NCR5380_write(TARGET_COMMAND_REG, 0);
    NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
    NCR5380_write(OUTPUT_DATA_REG, hostdata->id_mask);
    NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_DATA |
    ICR_ASSERT_SEL);

    while (probe_irq == IRQ_NONE && jiffies < timeout);

    NCR5380_write(SELECT_ENABLE_REG, 0);
    NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);

    for (i = 0, mask = 1; i < 16; ++i, mask <<= 1)
    if (trying_irqs & mask)
        free_irq(i);

    return probe_irq;
}
#endif /* AUTOPROBE_IRQ */

/*
 * Function : void NCR58380_print_options (struct Scsi_Host *instance)
 *
 * Purpose : called by probe code indicating the NCR5380 driver
 *         options that were selected.
 *
 * Inputs : instance, pointer to this instance.  Unused.
 */

static void NCR5380_print_options (struct Scsi_Host *instance)

{
    printk(" generic options"
#ifdef AUTOPROBE_IRQ
    " AUTOPROBE_IRQ"
#endif
#ifdef AUTOSENSE
    " AUTOSENSE"
#endif
#ifdef DIFFERENTIAL
    " DIFFERENTIAL"
#endif
#ifdef REAL_DMA
    " REAL DMA"
#endif
#ifdef REAL_DMA_POLL
    " REAL DMA POLL"
#endif
#ifdef PARITY
    " PARITY"
#endif
#ifdef PSEUDO_DMA
    " PSEUDO DMA"
#endif
#ifdef SCSI2
    " SCSI-2"
#endif
#ifdef UNSAFE
    " UNSAFE "
#endif
    );
#ifdef USLEEP
    printk(" USLEEP, USLEEP_POLL=%d USLEEP_SLEEP=%d", USLEEP_POLL, USLEEP_SLEEP);
#endif
    printk(" generic release=%d", NCR5380_PUBLIC_RELEASE);
}


/*
 * Function : void NCR5380_init (struct Scsi_Host *instance)
 *
 * Purpose : initializies *instance and corresponding 5380 chip.
 *
 * Inputs : instance - instantiation of the 5380 driver.
 *
 * Notes : I assume that the host, hostno, and id bits have been
 *     set correctly.  I don't care about the irq and other fields.
 *
 */

static void NCR5380_init (struct Scsi_Host *instance)

{
    NCR5380_local_declare();
    int i;
    struct NCR5380_hostdata *hostdata = (struct NCR5380_hostdata *)
    instance->hostdata;
    NCR5380_setup(instance);

    NCR5380_all_init();

    hostdata->id_mask = 1 << instance->this_id;
    for (i = hostdata->id_mask; i <= 0x80; i <<= 1)
    if (i > hostdata->id_mask)
        hostdata->id_higher_mask |= i;
    for (i = 0; i < 8; ++i)
    hostdata->busy[i] = 0;
#ifdef REAL_DMA
    hostdata->dma_len = 0;
#endif
    hostdata->connected = NULL;
    hostdata->issue_queue = NULL;
    hostdata->disconnected_queue = NULL;
    hostdata->flags = FLAG_CHECK_LAST_BYTE_SENT;

    if (!the_template) {
    the_template = instance->hostt;
    first_instance = instance;
    }


#ifdef USLEEP
    hostdata->time_expires = 0;
    hostdata->next_timer = NULL;
#endif

#ifndef AUTOSENSE
    if ((instance->cmd_per_lun > 1) || instance->can_queue > 1))
     printk("scsi%d : WARNING : support for multiple outstanding commands enabled\n"
            "         without AUTOSENSE option, contigent alligence conditions may\n"
            "         be incorrectly cleared.\n", instance->host_no);
#endif /* def AUTOSENSE */

    NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
    NCR5380_write(MODE_REG, MR_BASE);
    NCR5380_write(TARGET_COMMAND_REG, 0);
    NCR5380_write(SELECT_ENABLE_REG, 0);
}

/*
 * Function : int NCR5380_queue_command (Scsi_Cmnd *cmd,
 *    void (*done)(Scsi_Cmnd *))
 *
 * Purpose :  enqueues a SCSI command
 *
 * Inputs : cmd - SCSI command, done - function called on completion, with
 *    a pointer to the command descriptor.
 *
 * Returns : 0
 *
 * Side effects :
 *      cmd is added to the per instance issue_queue, with minor
 *    twiddling done to the host specific fields of cmd.  If the
 *    main coroutine is not running, it is restarted.
 *
 */

/* Only make static if a wrapper function is used */
#ifndef NCR5380_queue_command
static
#endif
int NCR5380_queue_command (Scsi_Cmnd *cmd, void (*done)(Scsi_Cmnd *))

{
    struct NCR5380_hostdata *hostdata = (struct NCR5380_hostdata *)
    cmd->host->hostdata;
    Scsi_Cmnd *tmp;

#if (NDEBUG & NDEBUG_NO_WRITE)
    switch (cmd->cmnd[0]) {
    case WRITE:
    case WRITE_10:
    printk("scsi%d : WRITE attempted with NO_WRITE debugging flag set\n",
        cmd->host->host_no);
    cmd->result = (DID_ERROR << 16);
    done(cmd);
    return 0;
    }
#endif /* (NDEBUG & NDEBUG_NO_WRITE) */


    /*
     * We use the host_scribble field as a pointer to the next command
     * in a queue
     */

    cmd->host_scribble = NULL;
    cmd->scsi_done = done;

    cmd->result = 0;


    /*
     * Insert the cmd into the issue queue. Note that REQUEST SENSE
     * commands are added to the head of the queue since any command will
     * clear the contingent allegience condition that exists and the
     * sense data is only guranteed to be valid while the condition exists.
     */

    cli();
    if (!(hostdata->issue_queue) || (cmd->cmnd[0] == REQUEST_SENSE)) {
    cmd->host_scribble = (unsigned char *) hostdata->issue_queue;
    hostdata->issue_queue = cmd;
    } else {
    for (tmp = (Scsi_Cmnd *) hostdata->issue_queue; tmp->host_scribble;
        tmp = (Scsi_Cmnd *) tmp->host_scribble);
    tmp->host_scribble = (unsigned char *) cmd;
    }
/*    sti(); */
#if (NDEBUG & NDEBUG_QUEUES)
    printk("scsi%d : command added to %s of queue\n", cmd->host->host_no,
    (cmd->cmnd[0] == REQUEST_SENSE) ? "head" : "tail");
#endif

/* Run the coroutine if it isn't allready running. */
    run_main();
    return 0;
}

/*
 * Function : NCR5380_main (void)
 *
 * Purpose : NCR5380_main is a corroutine that runs as long as more work can
 *    be done on the NCR5380 host adapters in a system.  Both
 *    NCR5380_queue_command() and NCR5380_intr() will try to start it
 *    in case it is not running.
 *
 * NOTE : NCR5380_main exits with interrupts *disabled*, the caller should
 *  reenable them.  This prevents rentrancy and kernel stack overflow.
 */

static void NCR5380_main (void)

{
    Scsi_Cmnd *tmp, *prev;
    struct Scsi_Host *instance;
    struct NCR5380_hostdata *hostdata;
    int done;

    /*
     * We run (with interrupts disabled) until we're sure that none of
     * the host adapters have anything that can be done, at which point
     * we set main_running to 0 and exit.
     *
     * Interrupts are enabled before doing various other internal
     * instructions, after we've decided that we need to run through
     * the loop again.
     *
     * this should prevent any race conditions.
     */

    do {
    cli(); /* Freeze request queues */
    done = 1;
    for (instance = first_instance; instance && instance->hostt == the_template;
        instance=instance->next) {
        hostdata = (struct NCR5380_hostdata *) instance->hostdata;
        cli();
        if (!hostdata->connected) {
#if (NDEBUG & NDEBUG_MAIN)
        printk("scsi%d : not connected\n", instance->host_no);
#endif
        /*
         * Search through the issue_queue for a command destined
         * for a target that's not busy.
         */
        for (tmp = (Scsi_Cmnd *) hostdata->issue_queue,
            prev = NULL; tmp; prev = tmp, tmp = (Scsi_Cmnd *)
            tmp->host_scribble)

            /*  When we find one, remove it from the issue queue. */
            if (!(hostdata->busy[tmp->target] & (1 << tmp->lun))) {
                if (prev)
                prev->host_scribble = tmp->host_scribble;
                else
                hostdata->issue_queue = (Scsi_Cmnd *) tmp->host_scribble;
            tmp->host_scribble = NULL;

            /* renable interrupts after finding one */
            CHECK_ICNT("main anbling ints before selecting");
            sti();

            /*
             * Attempt to establish an I_T_L nexus here.
             * On success, instance->hostdata->connected is set.
             * On failure, we must add the command back to the
             *   issue queue so we can keep trying.
             */
#if (NDEBUG & (NDEBUG_MAIN | NDEBUG_QUEUES))
            printk("scsi%d : main() : command for target %d lun %d removed from issue_queue\n",
                instance->host_no, tmp->target, tmp->lun);
#endif
                /*
                 * REQUEST SENSE commands are issued without tagged
                 * queueing, even on SCSI-II devices because the
                 * contingent alligence condition exists for the
                 * entire unit.
                 */

            if (!NCR5380_select(instance, tmp,
                (tmp->cmnd[0] == REQUEST_SENSE) ? TAG_NONE :
                TAG_NEXT)) {
                break;
            } else {
                cli();
                tmp->host_scribble = (unsigned char *)
                hostdata->issue_queue;
                hostdata->issue_queue = tmp;
                sti();
#if (NDEBUG & (NDEBUG_MAIN | NDEBUG_QUEUES))
            printk("scsi%d : main(): select() failed, returned to issue_queue\n",
                instance->host_no);
#endif
            }
            } /* if target/lun is not busy */
        } /* if (!hostdata->connected) */

        if (hostdata->connected
#ifdef REAL_DMA
        && !hostdata->dma_len
#endif
#ifdef USLEEP
        && (!hostdata->time_expires || hostdata->time_expires >= jiffies)
#endif
        ) {
        CHECK_ICNT("main enabling ints before inform_transf");
        sti();
#if (NDEBUG & NDEBUG_MAIN)
        printk("scsi%d : main() : performing information transfer\n",
            instance->host_no);
#endif
        NCR5380_information_transfer(instance);
#if (NDEBUG & NDEBUG_MAIN)
        printk("scsi%d : main() : done set false\n", instance->host_no);
#endif
        CHECK_ICNT("main finish with inform_transf");
        done = 0;
        } else
        break;
    } /* for instance */
    } while (!done);
    main_running = 0;
}


/*
 * Function : void NCR5380_dma_complete (struct Scsi_Host *instance)
 *
 * Purpose : Called by interrupt handler when DMA finishes or a phase
 *    mismatch occurs (which would finish the DMA transfer).
 *
 * Inputs : instance - this instance of the NCR5380.
 *
 */

static void NCR5380_dma_complete( struct Scsi_Host *instance )

{   struct NCR5380_hostdata *hostdata =
    (struct NCR5380_hostdata *)instance->hostdata;
    int           transfered;
    unsigned char **data, p, basr;
    volatile int  *count;
#ifdef READ_OVERRUNS
    int              saved_data = 0, overrun = 0, cnt, toPIO;
#else
    unsigned char sr;
#endif

    if (!hostdata->connected)
    panic("scsi%d : recieved end of DMA interrupt with no connected cmd\n",
          instance->host_no);

    p = hostdata->connected->SCp.phase;
    if (p & SR_IO) {
#ifdef READ_OVERRUNS
    udelay(10);
    if ((((basr = NCR5380_read(BUS_AND_STATUS_REG)) &
          (BASR_PHASE_MATCH|BASR_ACK)) == (BASR_PHASE_MATCH | BASR_ACK))) {
        saved_data = NCR5380_read(INPUT_DATA_REG);
        overrun = 1;
#if I_HAVE_OVERRUNS == 1
        /* Overrun probe mode: print a message that a overrun occured. */
        printk( "SCSI: overrun handled (better set I_HAVE_OVERRUNS to 2 in drivers/scsi/atari_scsi.h)\n" );
#endif
    }
#endif /* READ_OVERRUNS */
    }
    else {
    int limit = 100;
    while (((basr = NCR5380_read(BUS_AND_STATUS_REG)) & BASR_ACK) ||
           (NCR5380_read(STATUS_REG) & SR_REQ)) {
        if (!(basr & BASR_PHASE_MATCH)) break;
        if (--limit < 0) break;
    }
    }

#if (NDEBUG & NDEBUG_DMA)
    printk( "scsi%d : real DMA transfer complete, basr 0x%X, sr 0x%X\n",
        instance->host_no, basr, NCR5380_read(STATUS_REG));
#endif

    (void) NCR5380_read(RESET_PARITY_INTERRUPT_REG);
#if !defined(READ_OVERRUNS)
    while( NCR5380_read(BUS_AND_STATUS_REG) & BASR_ACK) ;
#endif
    NCR5380_write(MODE_REG, MR_BASE);
    NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);

    transfered = hostdata->dma_len - NCR5380_dma_residual(instance);
    hostdata->dma_len = 0;

    data = (unsigned char **) &(hostdata->connected->SCp.ptr);
    count = &(hostdata->connected->SCp.this_residual);
    *data += transfered;
    *count -= transfered;

#if !defined(READ_OVERRUNS)
    /* After turning off the DMA, a phase mismatch might occur. This
     * would cause another interrupt. But because DMA mode is already
     * cleared, NCR5380_intr() would report an unknown interrupt. To
     * avoid these messages, wait for REQ to be asserted again or for
     * an explicit phase mismatch. If REQ is asserted and the bus is
     * still in phase, no more interrupt will come.
     */
    while(!((sr=NCR5380_read(STATUS_REG)) & SR_REQ) && (sr & PHASE_MASK) == p)
    ;
    if ((sr & PHASE_MASK) != p) {
    (void) NCR5380_read(RESET_PARITY_INTERRUPT_REG);
    /* Note that the pending bit in the MFP must be cleared.
     * Otherwise the interrupt get delivered without the IRQ bit
     * set in the BASR.
     */
    if (IS_A_TT())
        tt_mfp.int_pn_a &= ~0x80;
    else
        mfp.int_pn_b &= ~0x80;
    }
#endif /* !READ_OVERRUNS */

    /* Now it save to turn on interrupts -- and it's better here in
     * case a slow PIO is done.
     */
    CHECK_ICNT("dma_complete enabling ints");
    sti();

#ifdef READ_OVERRUNS
    if ((NCR5380_read(STATUS_REG) & PHASE_MASK) == p && (p & SR_IO)) {
    if (overrun) {
#if (NDEBUG & NDEBUG_DMA)
        printk("Got an input overrun, using saved byte\n");
#endif
        *(*data)++ = saved_data;
        (*count)--;
        cnt = toPIO = 1;
    }
    else {
        cnt = toPIO = 2;
    }
#if (NDEBUG & NDEBUG_DMA)
    printk( "Doing %d-byte PIO to 0x%08lx\n", cnt, (long)*data );
#endif
    NCR5380_transfer_pio(instance, &p, &cnt, data);
    *count -= toPIO - cnt;
    }
#endif /* READ_OVERRUNS */

}


/*
 * Function : void NCR5380_intr (int irq)
 *
 * Purpose : handle interrupts, restablishing I_T_L or I_T_L_Q nexuses
 *    from the disconnected queue, and restarting NCR5380_main()
 *    as required.
 *
 * Inputs : int irq, irq that caused this interrupt.
 *
 */

static void NCR5380_intr (int irq)

{
    NCR5380_local_declare();
    struct Scsi_Host *instance;
    struct NCR5380_hostdata *hostdata;
    int done;
    unsigned char basr;
#if (NDEBUG & NDEBUG_INTR)
    printk("scsi : NCR5380 irq %d triggered\n", irq);
#endif
    do {
        done = 1;
        for (instance = first_instance; instance && (instance->hostt ==
         the_template); instance = instance->next) {
        if (instance->irq == irq) {

        hostdata = (struct NCR5380_hostdata *)instance->hostdata;
        /* Look for pending interrupts */
        NCR5380_setup(instance);
        basr = NCR5380_read(BUS_AND_STATUS_REG);
#if (NDEBUG & NDEBUG_INTR)
        printk( "scsi%d: BASR=%02x\n", instance->host_no, basr );
#endif
        /* XXX dispatch to appropriate routine if found and done=0 */
        if (basr & BASR_IRQ) {
#if (NDEBUG & NDEBUG_INTR)
            NCR5380_print(instance);
#endif
            if ((NCR5380_read(STATUS_REG) & (SR_SEL | SR_IO)) ==
            (SR_SEL | SR_IO)) {
            done = 0;
            sti();
#if (NDEBUG & NDEBUG_INTR)
            printk("scsi%d : SEL interrupt\n", instance->host_no);
#endif
            NCR5380_reselect(instance);
            (void) NCR5380_read(RESET_PARITY_INTERRUPT_REG);
            } else if (basr & BASR_PARITY_ERROR) {
#if (NDEBUG & NDEBUG_INTR)
            printk("scsi%d : PARITY interrupt\n", instance->host_no);
#endif
            (void) NCR5380_read(RESET_PARITY_INTERRUPT_REG);
            } else {
/*
 * XXX the rest of the interrupt conditions should *only* occur during a
 * DMA transfer, which I haven't gotten arround to fixing yet.
 */

#if defined(REAL_DMA)
            /*
             * We should only get PHASE MISMATCH and EOP
             * interrupts if we have DMA enabled, so do a
             * sanity check based on the current setting
             * of the MODE register.
             */

            if ((NCR5380_read(MODE_REG) & MR_DMA_MODE) &&
                ((basr & BASR_END_DMA_TRANSFER) ||
                 !(basr & BASR_PHASE_MATCH))) {

#if (NDEBUG & NDEBUG_INTR)
                printk("scsi%d : PHASE MISM or EOP interrupt\n",
                   instance->host_no);
#endif
                NCR5380_dma_complete( instance );
                done = 0;
            } else
#endif /* REAL_DMA */
                   {
#if 1 || (NDEBUG & NDEBUG_INTR)
                printk("scsi : unknown interrupt, BASR 0x%X, MR 0x%X, SR 0x%x\n",
                   basr, NCR5380_read(MODE_REG),
                   NCR5380_read(STATUS_REG));
#endif
                (void) NCR5380_read(RESET_PARITY_INTERRUPT_REG);
            }
            } /* if !(SELECTION || PARITY) */
        } /* BASR & IRQ */
        else {
#if 1 || (NDEBUG & NDEBUG_INTR)
            printk("scsi : interrupt without IRQ bit set in BASR, BASR 0x%X, MR 0x%X, SR 0x%x\n", basr, NCR5380_read(MODE_REG), NCR5380_read(STATUS_REG));
#endif
            (void) NCR5380_read(RESET_PARITY_INTERRUPT_REG);
        }
        } /* instance->irq == irq */
    } /* for instances */
    if (!done) {
#if (NDEBUG & NDEBUG_INTR)
        printk("scsi%d : in int routine: not done, calling main\n",
           instance->host_no);
#endif
        CHECK_ICNT("NCR5380_intr calling main");
        run_main();
        /* ++roman: After running main, interrupts are enabled and a
         * new DMA process may have been started. So we should leave
         * this instance of interrupt service routine! Otherwise
         * recursive calls may happen.
         */
        return;
    } /* !done */
    } while (0);
}

/*
 * Function : int NCR5380_select (struct Scsi_Host *instance, Scsi_Cmnd *cmd,
 *    int tag);
 *
 * Purpose : establishes I_T_L or I_T_L_Q nexus for new or existing command,
 *    including ARBITRATION, SELECTION, and initial message out for
 *    IDENTIFY and queue messages.
 *
 * Inputs : instance - instantiation of the 5380 driver on which this
 *     target lives, cmd - SCSI command to execute, tag - set to TAG_NEXT for
 *    new tag, TAG_NONE for untagged queueing, otherwise set to the tag for
 *    the command that is presently connected.
 *
 * Returns : -1 if selection could not execute for some reason,
 *    0 if selection succeeeded or failed because the target
 *     did not respond.
 *
 * Side effects :
 *     If bus busy, arbitration failed, etc, NCR5380_select() will exit
 *        with registers as they should have been on entry - ie
 *        SELECT_ENABLE will be set appropriately, the NCR5380
 *        will cease to drive any SCSI bus signals.
 *
 *    If successful : I_T_L or I_T_L_Q nexus will be established,
 *        instance->connected will be set to cmd.
 *         SELECT interrupt will be disabled.
 *
 *    If failed (no target) : cmd->scsi_done() will be called, and the
 *        cmd->result host byte set to DID_BAD_TARGET.
 */

static int NCR5380_select (struct Scsi_Host *instance, Scsi_Cmnd *cmd, int tag)

{
    NCR5380_local_declare();
    struct NCR5380_hostdata *hostdata = (struct NCR5380_hostdata*)
    instance->hostdata;
    unsigned char tmp[3], phase;
    unsigned char *data;
    int len;
    unsigned long timeout;
    NCR5380_setup(instance);

#if defined (NDEBUG) && (NDEBUG & NDEBUG_ARBITRATION)
    NCR5380_print(instance);
    printk("scsi%d : starting arbitration, id = %d\n", instance->host_no,
    instance->this_id);
#endif

    /*
     * Set the phase bits to 0, otherwise the NCR5380 won't drive the
     * data bus during SELECTION.
     */

    NCR5380_write(TARGET_COMMAND_REG, 0);

    /* Start arbitration */
    NCR5380_write(OUTPUT_DATA_REG, hostdata->id_mask);
    NCR5380_write(MODE_REG, MR_ARBITRATE);

    /* Wait for arbitration logic to complete */
    while (!(NCR5380_read(INITIATOR_COMMAND_REG) & ICR_ARBITRATION_PROGRESS));

#if (NDEBUG & NDEBUG_ARBITRATION)
    printk("scsi%d : arbitration complete\n", instance->host_no);
/* Avoid GCC 2.4.5 asm needs to many reloads error */
    __asm__("nop");
#endif

    /*
     * The arbitration delay is 2.2us, but this is a minimum and there is
     * no maximum so we can safely sleep for ceil(2.2) usecs to accomodate
     * the integral nature of udelay().
     *
     */

    udelay(3);

    /* Check for lost arbitration */
    if ((NCR5380_read(INITIATOR_COMMAND_REG) & ICR_ARBITRATION_LOST) ||
    (NCR5380_read(CURRENT_SCSI_DATA_REG) & hostdata->id_higher_mask) ||
    (NCR5380_read(INITIATOR_COMMAND_REG) & ICR_ARBITRATION_LOST)) {
    NCR5380_write(MODE_REG, MR_BASE);
#if (NDEBUG & NDEBUG_ARBITRATION)
    printk("scsi%d : lost arbitration, deasserting MR_ARBITRATE\n",
    instance->host_no);
#endif
    return -1;
    }

    NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_SEL);

    if (NCR5380_read(INITIATOR_COMMAND_REG) & ICR_ARBITRATION_LOST) {
    NCR5380_write(MODE_REG, MR_BASE);
    NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
#if (NDEBUG & NDEBUG_ARBITRATION)
    printk("scsi%d : lost arbitration, deasserting ICR_ASSERT_SEL\n",
    instance->host_no);
#endif
    return -1;
    }

    /*
     * Again, bus clear + bus settle time is 1.2us, however, this is
     * a minimum so we'll udelay ceil(1.2)
     */

    udelay(2);

#if (NDEBUG & NDEBUG_ARBITRATION)
    printk("scsi%d : won arbitration\n", instance->host_no);
#endif

    /*
     * Now that we have won arbitration, start Selection process, asserting
     * the host and target ID's on the SCSI bus.
     */

    NCR5380_write(OUTPUT_DATA_REG, (hostdata->id_mask | (1 << cmd->target)));

    /*
     * Raise ATN while SEL is true before BSY goes false from arbitration,
     * since this is the only way to gurantee that we'll get a MESSAGE OUT
     * phase immediately after selection.
     */

    NCR5380_write(INITIATOR_COMMAND_REG, (ICR_BASE | ICR_ASSERT_BSY |
    ICR_ASSERT_DATA | ICR_ASSERT_ATN | ICR_ASSERT_SEL ));
    NCR5380_write(MODE_REG, MR_BASE);

    /*
     * Reselect interrupts must be turned off prior to the dropping of BSY,
     * otherwise we will trigger an interrupt.
     */
    NCR5380_write(SELECT_ENABLE_REG, 0);

    /* Reset BSY */
    NCR5380_write(INITIATOR_COMMAND_REG, (ICR_BASE | ICR_ASSERT_DATA |
    ICR_ASSERT_ATN | ICR_ASSERT_SEL));

    /*
     * Something wierd happens when we cease to drive BSY - looks
     * like the board/chip is letting us do another read before the
     * appropriate propogation delay has expired, and we're confusing
     * a BSY signal from ourselves as the target's response to SELECTION.
     *
     * A small delay (the 'C++' frontend breaks the pipeline with an
     * unecessary jump, making it work on my 386-33/Trantor T128, the
     * tighter 'C' code breaks and requires this) solves the problem -
     * the 1 us delay is arbitrary, and only used because this delay will
     * be the same on other platforms and since it works here, it should
     * work there.
     */

    udelay(1);

#if (NDEBUG & NDEBUG_SELECTION)
    printk("scsi%d : selecting target %d\n", instance->host_no, cmd->target);
#endif

    /*
     * The SCSI specification calls for a 250 ms timeout for the actual
     * selection.
     */

    timeout = jiffies + 25;

    /*
     * XXX very interesting - we're seeing a bounce where the BSY we
     * asserted is being reflected / still asserted (propogation delay?)
     * and it's detecting as true.  Sigh.
     */

    while ((jiffies < timeout) && !(NCR5380_read(STATUS_REG) & SR_BSY));

    NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ATN);

    if (!(NCR5380_read(STATUS_REG) & SR_BSY)) {
    NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
    cmd->result = DID_BAD_TARGET << 16;
    cmd->scsi_done(cmd);
    NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
#if (NDEBUG & NDEBUG_SELECTION)
    printk("scsi%d : target did not respond within 250ms\n",
        instance->host_no);
#endif
    return 0;
    }

    /*
     * Since we followed the SCSI spec, and raised ATN while SEL
     * was true but before BSY was false during selection, the information
     * transfer phase should be a MESSAGE OUT phase so that we can send the
     * IDENTIFY message.
     *
     * If SCSI-II tagged queing is enabled, we also send a SIMPLE_QUEUE_TAG
     * message (2 bytes) with a tag ID that we increment with every command
     * until it wraps back to 0.
     *
     * XXX - it turns out that there are some broken SCSI-II devices,
     *         which claim to support tagged queing but fail when more than
     *         some number of commands are issued at once.
     */

    /* Wait for start of REQ/ACK handshake */
    while (!(NCR5380_read(STATUS_REG) & SR_REQ));

#if (NDEBUG & NDEBUG_SELECTION)
    printk("scsi%d : target %d selected, going into MESSAGE OUT phase.\n",
    instance->host_no, cmd->target);
#endif
    tmp[0] = IDENTIFY(((instance->irq == IRQ_NONE) ? 0 : 1), cmd->lun);
#ifdef SCSI2
    if (scsi_devices[cmd->index].tagged_queue && (tag != TAG_NONE)) {
    tmp[1] = SIMPLE_QUEUE_TAG;
    if (tag == TAG_NEXT) {
        /* 0 is TAG_NONE, used to imply no tag for this command */
        if (scsi_devices[cmd->index].current_tag == 0)
        scsi_devices[cmd->index].current_tag = 1;

        cmd->tag = scsi_devices[cmd->index].current_tag;
        scsi_devices[cmd->index].current_tag++;
    } else
        cmd->tag = (unsigned char) tag;

    tmp[2] = cmd->tag;
    hostdata->last_message = SIMPLE_QUEUE_TAG;
    len = 3;
    } else
#endif /* def SCSI2 */
    {
    len = 1;
    cmd->tag=0;
    }

    /* Send message(s) */
    data = tmp;
    phase = PHASE_MSGOUT;
    NCR5380_transfer_pio(instance, &phase, &len, &data);
#if (NDEBUG & NDEBUG_SELECTION)
    printk("scsi%d : nexus established.\n", instance->host_no);
#endif
    /* XXX need to handle errors here */
    hostdata->connected = cmd;
#ifdef SCSI2
    if (!scsi_devices[cmd->index].tagged_queue)
#endif
    hostdata->busy[cmd->target] |= (1 << cmd->lun);

    initialize_SCp(cmd);

    return 0;
}

/*
 * Function : int NCR5380_transfer_pio (struct Scsi_Host *instance,
 *      unsigned char *phase, int *count, unsigned char **data)
 *
 * Purpose : transfers data in given phase using polled I/O
 *
 * Inputs : instance - instance of driver, *phase - pointer to
 *    what phase is expected, *count - pointer to number of
 *    bytes to transfer, **data - pointer to data pointer.
 *
 * Returns : -1 when different phase is enterred without transfering
 *    maximum number of bytes, 0 if all bytes or transfered or exit
 *    is in same phase.
 *
 *     Also, *phase, *count, *data are modified in place.
 *
 * XXX Note : handling for bus free may be useful.
 */

/*
 * Note : this code is not as quick as it could be, however it
 * IS 100% reliable, and for the actual data transfer where speed
 * counts, we will always do a pseudo DMA or DMA transfer.
 */

static int NCR5380_transfer_pio( struct Scsi_Host *instance,
                 unsigned char *phase, int *count,
                 unsigned char **data)

{
    NCR5380_local_declare();
    register unsigned char p = *phase, tmp;
    register int c = *count;
    register unsigned char *d = *data;
    NCR5380_setup(instance);

    /*
     * The NCR5380 chip will only drive the SCSI bus when the
     * phase specified in the appropriate bits of the TARGET COMMAND
     * REGISTER match the STATUS REGISTER
     */

    NCR5380_write(TARGET_COMMAND_REG, PHASE_SR_TO_TCR(p));

    do {
    /*
     * Wait for assertion of REQ, after which the phase bits will be
     * valid
     */
    while (!((tmp = NCR5380_read(STATUS_REG)) & SR_REQ));

#if (NDEBUG & NDEBUG_HANDSHAKE)
    printk("scsi%d : REQ detected\n", instance->host_no);
#endif

    /* Check for phase mismatch */
    if ((tmp & PHASE_MASK) != p) {
#if (NDEBUG & NDEBUG_PIO)
        printk("scsi%d : phase mismatch\n", instance->host_no);
        NCR5380_print_phase(instance);
#endif
        break;
    }

    /* Do actual transfer from SCSI bus to / from memory */
    if (!(p & SR_IO))
        NCR5380_write(OUTPUT_DATA_REG, *d);
    else
        *d = NCR5380_read(CURRENT_SCSI_DATA_REG);

    ++d;

    /*
     * The SCSI standard suggests that in MSGOUT phase, the initiator
     * should drop ATN on the last byte of the message phase
     * after REQ has been asserted for the handshake but before
     * the initiator raises ACK.
     */

    if (!(p & SR_IO)) {
        if (!((p & SR_MSG) && c > 1)) {
        NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE |
            ICR_ASSERT_DATA);
#if (NDEBUG & NDEBUG_PIO)
    NCR5380_print(instance);
#endif
        NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE |
            ICR_ASSERT_DATA | ICR_ASSERT_ACK);
        } else {
        NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE |
            ICR_ASSERT_DATA | ICR_ASSERT_ATN);
#if (NDEBUG & NDEBUG_PIO)
    NCR5380_print(instance);
#endif
        NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE |
            ICR_ASSERT_DATA | ICR_ASSERT_ATN | ICR_ASSERT_ACK);
        }
    } else {
#if (NDEBUG & NDEBUG_PIO)
    NCR5380_print(instance);
#endif
    NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ACK);
    }

    while (NCR5380_read(STATUS_REG) & SR_REQ);

#if (NDEBUG & NDEBUG_HANDSHAKE)
        printk("scsi%d : req false, handshake complete\n", instance->host_no);
#endif

    if (!(p == PHASE_MSGOUT && c > 1))
        NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
    else
        NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ATN);
    } while (--c);

#if (NDEBUG & NDEBUG_PIO)
    printk("scsi%d : residual %d\n", instance->host_no, c);
#endif

    *count = c;
    *data = d;
    tmp = NCR5380_read(STATUS_REG);
    if (tmp & SR_REQ)
    *phase = tmp & PHASE_MASK;
    else
    *phase = PHASE_UNKNOWN;

    CHECK_ICNT("leaving transf_PIO");
    if (!c || (*phase == p))
    return 0;
    else
    return -1;
}

#if defined(REAL_DMA) || defined(PSEUDO_DMA) || defined (REAL_DMA_POLL)
/*
 * Function : int NCR5380_transfer_dma (struct Scsi_Host *instance,
 *      unsigned char *phase, int *count, unsigned char **data)
 *
 * Purpose : transfers data in given phase using either real
 *    or pseudo DMA.
 *
 * Inputs : instance - instance of driver, *phase - pointer to
 *    what phase is expected, *count - pointer to number of
 *    bytes to transfer, **data - pointer to data pointer.
 *
 * Returns : -1 when different phase is enterred without transfering
 *    maximum number of bytes, 0 if all bytes or transfered or exit
 *    is in same phase.
 *
 *     Also, *phase, *count, *data are modified in place.
 *
 */


static int NCR5380_transfer_dma( struct Scsi_Host *instance,
                 unsigned char *phase, int *count,
                 unsigned char **data)

{
    NCR5380_local_declare();
    register int c = *count;
    register unsigned char p = *phase;
    register unsigned char *d = *data;
    unsigned char tmp;
#if defined(REAL_DMA_POLL)
    int cnt, toPIO;
    unsigned char saved_data = 0, overrun = 0, residue;
#endif

    struct NCR5380_hostdata *hostdata = (struct NCR5380_hostdata *)
    instance->hostdata;

    NCR5380_setup(instance);

    if ((tmp = (NCR5380_read(STATUS_REG) & PHASE_MASK)) != p) {
        *phase = tmp;
        return -1;
    }
#if defined(REAL_DMA) || defined(REAL_DMA_POLL)
#ifdef READ_OVERRUNS
     if (p & SR_IO) {
       c -= 2;
     }
#endif /* READ_OVERRUNS */
#if (NDEBUG & NDEBUG_DMA)
    printk("scsi%d : initializing DMA channel %d for %s, %d bytes %s %0x\n",
    instance->host_no, instance->dma_channel, (p & SR_IO) ? "reading" :
    "writing", c, (p & SR_IO) ? "to" : "from", (unsigned) d);
#endif
    hostdata->dma_len = (p & SR_IO) ?
    NCR5380_dma_read_setup(instance, d, c) :
    NCR5380_dma_write_setup(instance, d, c);
#endif

    NCR5380_write(TARGET_COMMAND_REG, PHASE_SR_TO_TCR(p));

#ifdef REAL_DMA
    NCR5380_write(MODE_REG, MR_BASE | MR_DMA_MODE | MR_ENABLE_EOP_INTR | MR_MONITOR_BSY);
#elif defined(REAL_DMA_POLL)
    NCR5380_write(MODE_REG, MR_BASE | MR_DMA_MODE);
#else /* if PSEUDO_DMA */
    /*
     * Note : on my sample board, watch-dog timeouts occured when interrupts
     * were not disabled for the duration of a single DMA transfer, from
     * before the setting of DMA mode to after transfer of the last byte.
     */

#if defined(PSEUDO_DMA) && !defined(UNSAFE)
    cli();
#endif
    NCR5380_write(MODE_REG, MR_BASE | MR_DMA_MODE);
#endif /* def REAL_DMA ^ REAL_DMA_POLL ^ PSEUDO_DMA  */

#if (NDEBUG & NDEBUG_DMA) & 0
    printk("scsi%d : mode reg = 0x%X\n", instance->host_no, NCR5380_read(MODE_REG));
#endif

    if (p & SR_IO)
    NCR5380_write(START_DMA_INITIATOR_RECIEVE_REG, 0);
    else {
    NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_DATA);
    NCR5380_write(START_DMA_SEND_REG, 0);
    }

#if defined(REAL_DMA_POLL)
    do {
    tmp = NCR5380_read(BUS_AND_STATUS_REG);
    } while ((tmp & BASR_PHASE_MATCH) && !(tmp & (BASR_BUSY_ERROR |
    BASR_END_DMA_TRANSFER)));

/*
  At this point, either we've completed DMA, or we have a phase mismatch,
  or we've unexpectedly lost BUSY (which is a real error).

  For write DMAs, we want to wait until the last byte has been
  transferred out over the bus before we turn off DMA mode.  Alas, there
  seems to be no terribly good way of doing this on a 5380 under all
  conditions.  For non-scatter-gather operations, we can wait until REQ
  and ACK both go false, or until a phase mismatch occurs.  Gather-writes
  are nastier, since the device will be expecting more data than we
  are prepared to send it, and REQ will remain asserted.  On a 53C8[01] we
  could test LAST BIT SENT to assure transfer (I imagine this is precisely
  why this signal was added to the newer chips) but on the older 538[01]
  this signal does not exist.  The workaround for this lack is a watchdog;
  we bail out of the wait-loop after a modest amount of wait-time if
  the usual exit conditions are not met.  Not a terribly clean or
  correct solution :-%

  Reads are equally tricky due to a nasty characteristic of the NCR5380.
  If the chip is in DMA mode for an READ, it will respond to a target's
  REQ by latching the SCSI data into the INPUT DATA register and asserting
  ACK, even if it has _already_ been notified by the DMA controller that
  the current DMA transfer has completed!  If the NCR5380 is then taken
  out of DMA mode, this already-acknowledged byte is lost.

  This is not a problem for "one DMA transfer per command" reads, because
  the situation will never arise... either all of the data is DMA'ed
  properly, or the target switches to MESSAGE IN phase to signal a
  disconnection (either operation bringing the DMA to a clean halt).
  However, in order to handle scatter-reads, we must work around the
  problem.  The chosen fix is to DMA N-2 bytes, then check for the
  condition before taking the NCR5380 out of DMA mode.  One or two extra
  bytes are tranferred via PIO as necessary to fill out the original
  request.
*/

    if (p & SR_IO) {
#ifdef READ_OVERRUNS
      udelay(10);
      if (((NCR5380_read(BUS_AND_STATUS_REG) & (BASR_PHASE_MATCH|BASR_ACK)) ==
           (BASR_PHASE_MATCH | BASR_ACK))) {
        saved_data = NCR5380_read(INPUT_DATA_REGISTER);
        overrun = 1;
      }
#endif /* READ_OVERRUNS */
    } else {
      int limit = 100;
      while (((tmp = NCR5380_read(BUS_AND_STATUS_REG)) & BASR_ACK) ||
            (NCR5380_read(STATUS_REG) & SR_REQ)) {
        if (!(tmp & BASR_PHASE_MATCH)) break;
        if (--limit < 0) break;
      }
    }


#if (NDEBUG & NDEBUG_DMA)
    printk("scsi%d : polled DMA transfer complete, basr 0x%X, sr 0x%X\n",
       instance->host_no, tmp, NCR5380_read(STATUS_REG));
#endif

    NCR5380_write(MODE_REG, MR_BASE);
    NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);

    residue = NCR5380_dma_residual(instance);
    c -= residue;
    *count -= c;
    *data += c;
    *phase = NCR5380_read(STATUS_REG) & PHASE_MASK;

#ifdef READ_OVERRUNS
    if (*phase == p && (p & SR_IO) && residue == 0) {
      if (overrun) {
#if (NDEBUG & NDEBUG_DMA)
        printk("Got an input overrun, using saved byte\n");
#endif
        **data = saved_data;
        *data += 1;
        *count -= 1;
        cnt = toPIO = 1;
      } else {
        printk("No overrun??\n");
        cnt = toPIO = 2;
      }
#if (NDEBUG & NDEBUG_DMA)
      printk("Doing %d-byte PIO to 0x%X\n", cnt, *data);
#endif
      NCR5380_transfer_pio(instance, phase, &cnt, data);
      *count -= toPIO - cnt;
    }
#endif /* READ_OVERRUNS */

#if (NDEBUG & NDEBUG_DMA)
     printk("Return with data ptr = 0x%X, count %d, last 0x%X, next 0x%X\n",
        *data, *count, *(*data+*count-1), *(*data+*count));
#endif
     return 0;

#elif defined(REAL_DMA)
    CHECK_ICNT("leaving transf_dma");
    return 0;
#else /* defined(REAL_DMA_POLL) => PSEUDO_DMA */
    if (p & SR_IO) {
    if (!(foo = NCR5380_pread(instance, d, c - 1))) {
        /*
         * We can't disable DMA mode after successfully transfering
         * what we plan to be the last byte, since that would open up
         * a race condition where if the target asserted REQ before
         * we got the DMA mode reset, the NCR5380 would have latched
         * an additional byte into the INPUT DATA register and we'd
         * have dropped it.
         *
         * The workarround was to transfer one fewer bytes than we
         * intended to with the pseudo-DMA read function, wait for
         * the chip to latch the last byte, read it, and then disable
         * pseudo-DMA mode.
         *
         * After REQ is asserted, the NCR5380 asserts DRQ and ACK.
         * REQ is deasserted when ACK is asserted, and not reasserted
         * until ACK goes false.  Since the NCR5380 won't lower ACK
         * until DACK is asserted, which won't happen unless we twiddle
         * the DMA port or we take the NCR5380 out of DMA mode, we
         * can gurantee that we won't handshake another extra
         * byte.
             */

        while (!(NCR5380_read(BUS_AND_STATUS_REG) & BASR_DRQ));
        /* Wait for clean handshake */
        while (NCR5380_read(STATUS_REG) & SR_REQ);
        d[c - 1] = NCR5380_read(INPUT_DATA_REG);
    }
    } else {
    int timeout;
    if (!(foo = NCR5380_pwrite(instance, d, c))) {
        /*
         * Wait for the last byte to be sent.  If REQ is being asserted for
         * the byte we're interested, we'll ACK it and it will go false.
         */
        if (!(hostdata->flags & FLAG_HAS_LAST_BYTE_SENT)) {
        timeout = 20000;
#if 1
#if 1
        while (!(NCR5380_read(BUS_AND_STATUS_REG) &
            BASR_DRQ) && (NCR5380_read(BUS_AND_STATUS_REG) &
                BASR_PHASE_MATCH));
#else
        if (NCR5380_read(STATUS_REG) & SR_REQ) {
            for (; timeout &&
            !(NCR5380_read(BUS_AND_STATUS_REG) & BASR_ACK);
            --timeout);
            for (; timeout && (NCR5380_read(STATUS_REG) & SR_REQ);
            --timeout);
        }
#endif /* 1 */


#if (NDEBUG & NDEBUG_LAST_BYTE_SENT)
        if (!timeout)
            printk("scsi%d : timed out on last byte\n",
                instance->host_no);
#endif


        if (hostdata->flags & FLAG_CHECK_LAST_BYTE_SENT) {
            hostdata->flags &= ~FLAG_CHECK_LAST_BYTE_SENT;
            if (NCR5380_read(TARGET_COMMAND_REG) & TCR_LAST_BYTE_SENT) {
            hostdata->flags |= FLAG_HAS_LAST_BYTE_SENT;
#if (NDEBUG & NDEBUG_LAST_BYTE_SENT)
            printk("scsi%d : last bit sent works\n",
                instance->host_no);
#endif
            }
        }
        } else
        while (!(NCR5380_read(TARGET_COMMAND_REG) & TCR_LAST_BYTE_SENT));
#else /* 1 */
        udelay (5);
#endif
    }
    }

    NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
    NCR5380_write(MODE_REG, MR_BASE);

    *data = d + c;
    *count = 0;
    *phase = (NCR5380_read(STATUS_REG & PHASE_MASK));
#if defined(PSEUDO_DMA) && !defined(UNSAFE)
    sti();
#endif /* defined(REAL_DMA_POLL) */
    return foo;
#endif /* def REAL_DMA */
}
#endif /* defined(REAL_DMA) | defined(PSEUDO_DMA) */

/*
 * Function : NCR5380_information_transfer (struct Scsi_Host *instance)
 *
 * Purpose : run through the various SCSI phases and do as the target
 *     directs us to.  Operates on the currently connected command,
 *    instance->connected.
 *
 * Inputs : instance, instance for which we are doing commands
 *
 * Side effects : SCSI things happen, the disconnected queue will be
 *    modified if a command disconnects, *instance->connected will
 *    change.
 *
 * XXX Note : we need to watch for bus free or a reset condition here
 *     to recover from an unexpected bus free condition.
 */

static void NCR5380_information_transfer (struct Scsi_Host *instance)

{
    NCR5380_local_declare();
    struct NCR5380_hostdata *hostdata = (struct NCR5380_hostdata *)
    instance->hostdata;
    unsigned char msgout = NOP;
    int len, transfersize;
    unsigned char *data;
    unsigned char phase, tmp, old_phase=0xff;
    Scsi_Cmnd *cmd = (Scsi_Cmnd *) hostdata->connected;
    NCR5380_setup(instance);

    while (1) {
    tmp = NCR5380_read(STATUS_REG);
    /* We only have a valid SCSI phase when REQ is asserted */
    if (tmp & SR_REQ) {
        phase = (tmp & PHASE_MASK);
        if (phase != old_phase) {
        old_phase = phase;
#if (NDEBUG & NDEBUG_INFORMATION)
        NCR5380_print_phase(instance);
#endif
        }
        switch (phase) {
        case PHASE_DATAOUT:
#if (NDEBUG & NDEBUG_NO_DATAOUT)
        printk("scsi%d : NDEBUG_NO_DATAOUT set, attempted DATAOUT aborted\n",
            instance->host_no);
        msgout = ABORT;
        NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ATN);
        break;
#endif
        case PHASE_DATAIN:
        /*
         * If there is no room left in the current buffer in the
         * scatter-gather list, move onto the next one.
         */

        if (!cmd->SCp.this_residual && cmd->SCp.buffers_residual) {
            ++cmd->SCp.buffer;
            --cmd->SCp.buffers_residual;
            cmd->SCp.this_residual = cmd->SCp.buffer->length;
            cmd->SCp.ptr = cmd->SCp.buffer->address;
            /* ++roman: Try to merge some scatter-buffers if
             * they are at consecutive physical addresses.
             */
            merge_consecutive_buffers( cmd );
#if (NDEBUG & NDEBUG_INFORMATION)
            printk("scsi%d : %d bytes and %d buffers left\n",
            instance->host_no, cmd->SCp.this_residual,
            cmd->SCp.buffers_residual);
#endif
        }

        /*
         * The preffered transfer method is going to be
         * PSEUDO-DMA for systems that are strictly PIO,
         * since we can let the hardware do the handshaking.
         *
         * For this to work, we need to know the transfersize
         * ahead of time, since the pseudo-DMA code will sit
         * in an unconditional loop.
         */

/* ++roman: I suggest, this should be
 *   #if def(REAL_DMA) || def(PSEUDO_DMA) || ...
 * instead of leaving REAL_DMA out.
 */

        CHECK_ICNT("starting transf in inform_transf");
#if defined(REAL_DMA) || defined(PSEUDO_DMA) || defined(REAL_DMA_POLL)
#ifdef NCR5380_dma_xfer_len
        if (!scsi_devices[cmd->index].borken &&
            (transfersize = NCR5380_dma_xfer_len(instance, cmd)) > 7) {
#else
        if (!scsi_devices[cmd->index].borken &&
            (transfersize = cmd->transfersize) &&
            cmd->SCp.this_residual && !(cmd->SCp.this_residual %
            transfersize)) {
#endif
            len = transfersize;
            cmd->SCp.phase = phase;
            if (NCR5380_transfer_dma(instance, &phase,
            &len, (unsigned char **) &cmd->SCp.ptr)) {
            /*
             * If the watchdog timer fires, all future
             * accesses to this device will use the
             * polled-IO. */
            printk("scsi%d : switching target %d lun %d to slow handshake\n",
                instance->host_no, cmd->target, cmd->lun);
            scsi_devices[cmd->index].borken = 1;
            NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE |
                ICR_ASSERT_ATN);
            msgout = ABORT;
            } else {
#ifdef REAL_DMA
            /* ++roman: When using real DMA,
             * information_transfer() should return after
             * starting DMA since it has nothing more to
             * do.
             */
            return;
#else
            cmd->SCp.this_residual -= transfersize - len;
#endif
            }
        } else
#endif /* defined(REAL_DMA) || defined(REAL_DMA_POLL) */
          NCR5380_transfer_pio(instance, &phase,
            (int *) &cmd->SCp.this_residual, (unsigned char **)
            &cmd->SCp.ptr);
        break;
        case PHASE_MSGIN:
        /*
         * XXX - we don't handle multi-byte messages here, since we
         * shouldn't get them after the I_T_L_Q nexus is established
         * for tagged queuing, and the host should initiate any
         * negotiations for sync. SCSI, etc.
         */
        len = 1;
        data = &tmp;
        NCR5380_transfer_pio(instance, &phase, &len, &data);
        cmd->SCp.Message = tmp;

        switch (tmp) {
        /*
         * Linking lets us reduce the time required to get the
         * next command out to the device, hopefully this will
         * mean we don't waste another revolution due to the delays
         * required by ARBITRATION and another SELECTION.
         *
         * In the current implementation proposal, low level drivers
         * merely have to start the next command, pointed to by
         * next_link, done() is called as with unlinked commands.
         */
#ifdef LINKED
        case LINKED_CMD_COMPLETE:
        case LINKED_FLG_CMD_COMPLETE:
#if (NDEBUG & NDEBUG_LINKED)
            printk("scsi%d : target %d lun %d linked command complete.\n",
            instance->host_no, cmd->target, cmd->lun);
#endif
            /*
             * Sanity check : A linked command should only terminate with
             * one of these messages if there are more linked commands
             * available.
             */

            if (!cmd->next_link) {
             printk("scsi%d : target %d lun %d linked command complete, no next_link\n"
                instance->host_no, cmd->target, cmd->lun);
                msgout = ABORT;
                NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE |
                ICR_ASSERT_ATN);
                break;
            }

            initialize_SCp(cmd->next_link);
            /* The next command is still part of this process */
            cmd->next_link->tag = cmd->tag;
            cmd->result = cmd->SCp.Status | (cmd->SCp.Message << 8);
#if (NDEBUG & NDEBUG_LINKED)
            printk("scsi%d : target %d lun %d linked request done, calling scsi_done().\n",
            instance->host_no, cmd->target, cmd->lun);
#endif
            cmd->scsi_done(cmd);
            cmd = hostdata->connected;
            break;
#endif /* def LINKED */
        case ABORT:
        case COMMAND_COMPLETE:
            hostdata->connected = NULL;
#if (NDEBUG & NDEBUG_QUEUES)
            printk("scsi%d : command for target %d, lun %d completed\n",
            instance->host_no, cmd->target, cmd->lun);
#endif
            hostdata->busy[cmd->target] &= ~(1 << cmd->lun);

            /* ++roman: For Falcon SCSI, release the lock an on the
             * ST-DMA here if no other commands are waiting on the
             * disconnected queue.
             */
            falcon_release_lock_if_possible( hostdata );

            /*
             * I'm not sure what the correct thing to do here is :
             *
             * If the command that just executed is NOT a request
             * sense, the obvious thing to do is to set the result
             * code to the values of the stored parameters.
             *
             * If it was a REQUEST SENSE command, we need some way
             * to differentiate between the failure code of the original
             * and the failure code of the REQUEST sense - the obvious
             * case is success, where we fall through and leave the result
             * code unchanged.
             *
             * The non-obvious place is where the REQUEST SENSE failed
             */

#if 0
            /* ++roman: */
            if (cmd->SCp.this_residual || cmd->SCp.buffers_residual) {
            /* We would expect more bytes to transfer, but
             * the target switch phase ?!?
             */
            cmd->result = cmd->SCp.Status |
                          (cmd->SCp.Message << 8) |
                      (DID_ERROR << 16);
            printk( "SCSI: bytes left after transfer: this_residual=%d buffers_residual=%d\n",
                cmd->SCp.this_residual,
                cmd->SCp.buffers_residual );
            }

            else
#endif
            if (cmd->cmnd[0] != REQUEST_SENSE)
            cmd->result = cmd->SCp.Status | (cmd->SCp.Message << 8);
            else if (cmd->SCp.Status != GOOD)
            cmd->result = (cmd->result & 0x00ffff) | (DID_ERROR << 16);

#ifdef AUTOSENSE
            if ((cmd->cmnd[0] != REQUEST_SENSE) &&
            (cmd->SCp.Status == CHECK_CONDITION)) {
#if (NDEBUG & NDEBUG_AUTOSENSE)
            printk("scsi%d : performing request sense\n",
                instance->host_no);
#endif
            cmd->cmnd[0] = REQUEST_SENSE;
            cmd->cmnd[1] &= 0xe0;
            cmd->cmnd[2] = 0;
            cmd->cmnd[3] = 0;
            cmd->cmnd[4] = sizeof(cmd->sense_buffer);
            cmd->cmnd[5] = 0;

            cmd->SCp.buffer = NULL;
            cmd->SCp.buffers_residual = 0;
            cmd->SCp.ptr = (char *) cmd->sense_buffer;
            cmd->SCp.this_residual = sizeof(cmd->sense_buffer);

            cli();
            cmd->host_scribble = (unsigned char *)
                hostdata->issue_queue;
                hostdata->issue_queue = (Scsi_Cmnd *) cmd;
                sti();
#if (NDEBUG & NDEBUG_QUEUES)
            printk("scsi%d : REQUEST SENSE added to head of issue queue\n",
                   instance->host_no);
#endif
           } else
#endif /* def AUTOSENSE */
            cmd->scsi_done(cmd);

            NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);

            while ((NCR5380_read(STATUS_REG) & SR_BSY) &&
            !hostdata->connected);
            return;
        case MESSAGE_REJECT:
            switch (hostdata->last_message) {
            case HEAD_OF_QUEUE_TAG:
            case ORDERED_QUEUE_TAG:
            case SIMPLE_QUEUE_TAG:
            scsi_devices[cmd->index].tagged_queue = 0;
            hostdata->busy[cmd->target] |= (1 << cmd->lun);
            break;
            default:
            break;
            }
        case DISCONNECT:
            scsi_devices[cmd->index].disconnect = 1;
            cli();
            cmd->host_scribble = (unsigned char *)
            hostdata->disconnected_queue;
            hostdata->connected = NULL;
            hostdata->disconnected_queue = cmd;
            sti();
#if (NDEBUG & NDEBUG_QUEUES)
            printk("scsi%d : command for target %d lun %d was moved from connected to"
                   "  the disconnected_queue\n", instance->host_no,
                cmd->target, cmd->lun);
#endif

            /* Enable reselect interupts */
            NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
            /* Wait for bus free to avoid nasty timeouts */
            while ((NCR5380_read(STATUS_REG) & SR_BSY) &&
            !hostdata->connected);
            return;
        /*
         * The SCSI data pointer is *IMPLICITLY* saved on a disconnect
         * operation, in violation of the SCSI spec so we can safely
         * ignore SAVE/RESTORE pointers calls.
         *
         * Unfortunately, some disks violate the SCSI spec and
         * don't issue the required SAVE_POINTERS message before
         * disconnecting, and we have to break spec to remain
         * compatable.
         */
        case SAVE_POINTERS:
        case RESTORE_POINTERS:
            break;
        default:
/*
 * XXX rejected messages should be handled in the pio data transfer phase,
 * since ATN should be raised before ACK goes false when we reject a message
 */

            printk("Unknown message!\n");

#ifdef notyet
        /*
           * If we get something wierd that we aren't expecting,
          * reject it.
         */
            msgout = MESSAGE_REJECT;
            NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE |
            ICR_ASSERT_ATN);
#endif
            break;
        } /* switch (tmp) */
        break;
        case PHASE_MSGOUT:
        len = 1;
        data = &msgout;
        hostdata->last_message = msgout;
        NCR5380_transfer_pio(instance, &phase, &len, &data);
        if (msgout == ABORT) {
            hostdata->busy[cmd->target] &= ~(1 << cmd->lun);
            hostdata->connected = NULL;
            cmd->result = DID_ERROR << 16;
            cmd->scsi_done(cmd);
            NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
            falcon_release_lock_if_possible( hostdata );
            return;
        }
        msgout = NOP;
        break;
        case PHASE_CMDOUT:
        len = COMMAND_SIZE(cmd->cmnd[0]);
        data = cmd->cmnd;
        /*
         * XXX for performance reasons, on machines with a
         * PSEUDO-DMA architecture we should probably
         * use the dma transfer function.
         */
        NCR5380_transfer_pio(instance, &phase, &len,
            &data);
#ifdef USLEEP
        if (!disconnect && should_disconnect(cmd->cmnd[0])) {
            hostdata->time_expires = jiffies + USLEEP_SLEEP;
#if (NDEBUG & NDEBUG_USLEEP)
        printk("scsi%d : issued command, sleeping until %ul\n", instance->host_no,
            hostdata->time_expires);
#endif
            NCR5380_set_timer (instance);
            return;
        }
#endif /* def USLEEP */
        break;
        case PHASE_STATIN:
        len = 1;
        data = &tmp;
        NCR5380_transfer_pio(instance, &phase, &len, &data);
        cmd->SCp.Status = tmp;
        break;
        default:
        printk("scsi%d : unknown phase\n", instance->host_no);
#ifdef NDEBUG
        NCR5380_print(instance);
#endif
        } /* switch(phase) */
    } /* if (tmp * SR_REQ) */
#ifdef USLEEP
    else {
        if (!disconnect && hostdata->time_expires && jiffies >
        hostdata->time_expires) {
        hostdata->time_expires = jiffies + USLEEP_SLEEP;
#if (NDEBUG & NDEBUG_USLEEP)
        printk("scsi%d : poll timed out, sleeping until %ul\n", instance->host_no,
            hostdata->time_expires);
#endif
        NCR5380_set_timer (instance);
        return;
        }
    }
#endif
    } /* while (1) */
}

/*
 * Function : void NCR5380_reselect (struct Scsi_Host *instance)
 *
 * Purpose : does reselection, initializing the instance->connected
 *    field to point to the Scsi_Cmnd for which the I_T_L or I_T_L_Q
 *    nexus has been restablished,
 *
 * Inputs : instance - this instance of the NCR5380.
 *
 */


static void NCR5380_reselect (struct Scsi_Host *instance)

{
    NCR5380_local_declare();
    struct NCR5380_hostdata *hostdata = (struct NCR5380_hostdata *)
    instance->hostdata;
    unsigned char target_mask;
    unsigned char lun, phase;
    int len;
#ifdef SCSI2
    unsigned char tag;
#endif
    unsigned char msg[3];
    unsigned char *data;
    Scsi_Cmnd *tmp = NULL, *prev;
    int abort = 0;
    NCR5380_setup(instance);

    target_mask = NCR5380_read(CURRENT_SCSI_DATA_REG) & ~(hostdata->id_mask);

#if (NDEBUG & NDEBUG_RESELECTION)
    printk("scsi%d : reselect\n", instance->host_no);
#endif

    /*
     * At this point, we have detected that our SCSI ID is on the bus,
     * SEL is true and BSY was false for at least one bus settle delay
     * (400 ns).
     *
     * We must assert BSY ourselves, until the target drops the SEL
     * signal.
     */

    NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_BSY);

    while (NCR5380_read(STATUS_REG) & SR_SEL);
    NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);

    /*
     * Wait for target to go into MSGIN.
     */

    while (!(NCR5380_read(STATUS_REG) & SR_REQ));

    len = 3;
    data = msg;
    phase = PHASE_MSGIN;
    NCR5380_transfer_pio(instance, &phase, &len, &data);

#ifdef SCSI2
    /*
     * If there was no residual from the attempt to transfer three bytes, then
     * the target sent the one byte IDENTIFY message followed by a two byte
     * queue message.
     *
     * If there were two bytes of residual, we got the IDENTIFY message
     * only.
     *
     * If there was one byte of residual, we got the IDENTIFY message
     * followed by a RESTORE pointers message (which was ignored -
     * see MSGIN phase of the NCR5380_information_transfer() function.
     */

    if (!len)
    tag = msg[2];
    else
    tag = 0;
#endif

    if (!msg[0] & 0x80) {
    printk("scsi%d : expecting IDENTIFY message, got ",
        instance->host_no);
    print_msg(msg);
    abort = 1;
    } else {

    lun = (msg[0] & 0x07);

    /*
     * Find the command corresponding to the I_T_L or I_T_L_Q  nexus we
     * just restablished, and remove it from the disconnected queue.
     */

    for (tmp = (Scsi_Cmnd *) hostdata->disconnected_queue, prev = NULL;
        tmp; prev = tmp, tmp = (Scsi_Cmnd *) tmp->host_scribble)
        if ((target_mask == (1 << tmp->target)) && (lun == tmp->lun)
#ifdef SCSI2
        && (tag == tmp->tag)
#endif
) {
        if (prev)
        prev->host_scribble = tmp->host_scribble;
        else
        hostdata->disconnected_queue = (Scsi_Cmnd *) tmp->host_scribble;
        tmp->host_scribble = NULL;
        break;
    }

    if (!tmp) {
#ifdef SCSI2
        printk("scsi%d : warning : target bitmask %02x lun %d tag %d not in disconnect_queue.\n",
            instance->host_no, target_mask, lun, tag);
#else
        printk("scsi%d : warning : target bitmask %02x lun %d not in disconnect_queue.\n",
            instance->host_no, target_mask, lun);
#endif
    /*
     * Since we have an established nexus that we can't do anything with,
     * we must abort it.
     */
    abort = 1;
    }
    }

    if (abort) {
    msg[0] = ABORT;
    len = 1;
    data = msg;
    phase = PHASE_MSGOUT;
    NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ATN);
    NCR5380_transfer_pio(instance, &phase, &len, &data);
    } else {
    hostdata->connected = tmp;
#if (NDEBUG & NDEBUG_RESELECTION)
    printk("scsi%d : nexus established, target = %d, lun = %d, tag = %d\n",
        instance->host_no, tmp->target, tmp->lun, tmp->tag);
#endif
    }
}


/*
 * Function : int NCR5380_abort (Scsi_Cmnd *cmd, int code)
 *
 * Purpose : abort a command
 *
 * Inputs : cmd - the Scsi_Cmnd to abort, code - code to set the
 *     host byte of the result field to, if zero DID_ABORTED is
 *    used.
 *
 * Returns : 0 - success, -1 on failure.
 *
 * XXX - there is no way to abort the command that is currently
 *      connected, you have to wait for it to complete.  If this is
 *     a problem, we could implement longjmp() / setjmp(), setjmp()
 *      called where the loop started in NCR5380_main().
 */

#ifndef NCR5380_abort
static
#endif
int NCR5380_abort (Scsi_Cmnd *cmd, int code)

{
    NCR5380_local_declare();
    struct Scsi_Host *instance = cmd->host;
    struct NCR5380_hostdata *hostdata = (struct NCR5380_hostdata *)
    instance->hostdata;
    Scsi_Cmnd *tmp, **prev;
    unsigned char msg, phase, *msgptr;
    int len;

    cli();
    NCR5380_setup(instance);

#if (NDEBUG & NDEBUG_ABORT)
    printk("scsi%d : abort called\n", instance->host_no);
    printk("        basr 0x%X, sr 0x%X\n",
       NCR5380_read(BUS_AND_STATUS_REG), NCR5380_read(STATUS_REG));
    NCR5380_print(instance);
    NCR5380_print_phase(instance);
#endif
/*
 * Case 1 : If the command hasn't been issued yet, we simply remove it
 *         from the issue queue.
 */
    for (prev = (Scsi_Cmnd **) &(hostdata->issue_queue),
    tmp = (Scsi_Cmnd *) hostdata->issue_queue;
    tmp; prev = (Scsi_Cmnd **) &(tmp->host_scribble), tmp =
    (Scsi_Cmnd *) tmp->host_scribble)
    if (cmd == tmp) {
        (*prev) = (Scsi_Cmnd *) tmp->host_scribble;
        tmp->host_scribble = NULL;
        tmp->result = (code ? code : DID_ABORT) << 16;
        sti();
#if (NDEBUG & NDEBUG_ABORT)
    printk("scsi%d : abort removed command from issue queue.\n",
    instance->host_no);
#endif
        tmp->done(tmp);
        return 0;
    }

/*
 * Case 2 : If any commands are connected, we're going to fail the abort
 *        and let the high level SCSI driver retry at a later time or
 *        issue a reset.
 *
 *        Timeouts, and therefore aborted commands, will be highly unlikely
 *          and handling them cleanly in this situation would make the common
 *        case of noresets less efficient, and would pollute our code.  So,
 *        we fail.
 */

    if (hostdata->connected) {
    sti();
#if (NDEBUG & NDEBUG_ABORT)
    printk("scsi%d : abort failed, command connected.\n", instance->host_no);
#endif
        return -1;
    }

/*
 * Case 3: If the command is currently disconnected from the bus, and
 *     there are no connected commands, we reconnect the I_T_L or
 *    I_T_L_Q nexus associated with it, go into message out, and send
 *      an abort message.
 *
 * This case is especially ugly. In order to resetablish the nexus, we
 * need to call NCR5380_select().  The easiest way to implement this
 * function was to abort if the bus was busy, and let the interrupt
 * handler triggered on the SEL for reselect take care of lost arbitrations
 * where necessary, meaning interrupts need to be enabled.
 *
 * When interrupts are enabled, the queues may change - so we
 * can't remove it from the disconnected queue before selecting it
 * because that could cause a failure in hashing the nexus if that
 * device reselected.
 *
 * Since the queues may change, we can't use the pointers from when we
 * first locate it.
 *
 * So, we must first locate the command, and if NCR5380_select()
 * succeeds, then issue the abort, relocate the command and remove
 * it from the disconnected queue.
 */

    for (tmp = (Scsi_Cmnd *) hostdata->disconnected_queue; tmp;
    tmp = (Scsi_Cmnd *) tmp->host_scribble)
        if (cmd == tmp) {
            sti();
#if (NDEBUG & NDEBUG_ABORT)
    printk("scsi%d : aborting disconnected command.\n", instance->host_no);
#endif

            if (NCR5380_select (instance, cmd, (int) cmd->tag))
        return 1;

#if (NDEBUG & NDEBUG_ABORT)
    printk("scsi%d : nexus restablished.\n", instance->host_no);
#endif

        msg = ABORT;
        msgptr = &msg;
        len = 1;
        phase = PHASE_MSGOUT;
        NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ATN);
        NCR5380_transfer_pio (instance, &phase, &len, &msgptr);

        cli();
        for (prev = (Scsi_Cmnd **) &(hostdata->disconnected_queue),
        tmp = (Scsi_Cmnd *) hostdata->disconnected_queue;
        tmp; prev = (Scsi_Cmnd **) &(tmp->host_scribble), tmp =
        (Scsi_Cmnd *) tmp->host_scribble)
            if (cmd == tmp) {
            *prev = (Scsi_Cmnd *) tmp->host_scribble;
            tmp->host_scribble = NULL;
            tmp->result = (code ? code : DID_ABORT) << 16;
            sti();
            tmp->done(tmp);
            return 0;
        }
    }

/*
 * Case 4 : If we reached this point, the command was not found in any of
 *        the queues.
 *
 * We probably reached this point because of an unlikely race condition
 * between the command completing successfully and the abortion code,
 * so we won't panic, but we will notify the user in case somethign really
 * broke.
 */

    sti();
    printk("scsi%d : warning : SCSI command probably completed successfully\n"
           "         before abortion\n", instance->host_no);
    return 0;
}


/*
 * Function : int NCR5380_reset (Scsi_Cmnd *cmd)
 *
 * Purpose : reset the SCSI bus.
 *
 * Returns : 0
 *
 */

#ifndef NCR5380_reset
static
#endif
int NCR5380_reset( Scsi_Cmnd *cmd )

{   unsigned long timeout;
    unsigned      oldflags;
    int           i;
    struct NCR5380_hostdata *hostdata =
    (struct NCR5380_hostdata *)cmd->host->hostdata;
    NCR5380_local_declare();
    NCR5380_setup(cmd->host);

#if (NDEBUG & NDEBUG_ABORT)
    printk( "scsi%d: doing SCSI reset!\n", cmd->host->host_no );
#endif

    /* get in phase */
    NCR5380_write( TARGET_COMMAND_REG,
           PHASE_SR_TO_TCR( NCR5380_read(STATUS_REG) ));
    /* assert RST */
    NCR5380_write( INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_RST );

    /* Wait for 40 .. 50 ms (min. is 25 ms) */
    save_flags( oldflags );
    sti();
    for( timeout = jiffies + 5; jiffies < timeout; )
    ;
    restore_flags( oldflags );

    /* reset NCR registers */
    NCR5380_write( INITIATOR_COMMAND_REG, ICR_BASE );
    NCR5380_write( MODE_REG, MR_BASE );
    NCR5380_write( TARGET_COMMAND_REG, 0 );
    NCR5380_write( SELECT_ENABLE_REG, 0 );

    /* After the reset, there are no more connected or disconnected commands
     * and no busy units */
    cli();
    if ((cmd = (Scsi_Cmnd *)hostdata->connected)) {
#if (NDEBUG & NDEBUG_ABORT)
    printk( "scsi%d: reset aborted a connected command\n", cmd->host->host_no);
#endif
    cmd->result = (cmd->result & 0xffff) | (DID_RESET << 16);
    cmd->scsi_done( cmd );
    hostdata->connected = NULL;
    }

    for( i = 0, cmd = (Scsi_Cmnd *)hostdata->disconnected_queue; cmd;
     cmd = (Scsi_Cmnd *)cmd->host_scribble, ++i ) {
    cmd->result = (cmd->result & 0xffff) | (DID_RESET << 16);
    cmd->scsi_done( cmd );
    }
#if (NDEBUG & NDEBUG_ABORT)
    if (i > 0)
    printk( "scsi%d: reset aborted %d disconnected command(s)\n",
        cmd->host->host_no, i );
#endif
    hostdata->disconnected_queue = NULL;
    sti();

    for( i = 0; i < 8; ++i )
    hostdata->busy[i] = 0;

#if defined(REAL_DMA) || defined(REAL_DMA_POLL)
    hostdata->dma_len = 0;
#endif

    return 0;
}