home *** CD-ROM | disk | FTP | other *** search
/ NetNews Usenet Archive 1993 #1 / NN_1993_1.iso / spool / comp / sys / amiga / hardware / 22815 < prev    next >
Encoding:
Internet Message Format  |  1993-01-12  |  3.0 KB

  1. Path: sparky!uunet!munnari.oz.au!spool.mu.edu!howland.reston.ans.net!usc!cs.utexas.edu!torn!news.ccs.queensu.ca!qucdn!leek
  2. Organization: Queen's University at Kingston
  3. Date: Tue, 12 Jan 1993 01:03:59 EST
  4. From: <LEEK@QUCDN.QueensU.CA>
  5. Message-ID: <93012.010359LEEK@QUCDN.QueensU.CA>
  6. Newsgroups: comp.sys.amiga.hardware
  7. Subject: Re: EPROM programers and Amiga
  8. References:  <49ogs*J21@wolf359.UUCP>
  9. Lines: 57
  10.  
  11. In article <49ogs*J21@wolf359.UUCP>, eric@wolf359.UUCP (Eric Edwards) says:
  12. >
  13. >I've decided to try my hand at building Zorro II/III boards.  For this I
  14. >will need to program EPROMS (Autoconfig) and preferably, GALs as well.
  15.  
  16. Yeap.  Have you consider EEPROM ?  It would probably save a lot of time
  17. as you don't have to power down, pull it out, tan it in uv for 5-15
  18. minutes, power up Amiga, pop in chip in yet another untested hardware to
  19. program it, turn off Amiga, plug it into card, power up to test card....
  20.  
  21. >I've not had much luck in finding the required tools. The only
  22. >specifically Amiga tool I've seen is GALer, from one of the fish disks.
  23.  
  24. There is Epromer (right ?) V2.0.  It was available in ab20 site and it
  25. should be in WUarchive under /systems/amiga/info/hardware.  I didn't like
  26. the original BASIC timing loops (V.1), so I designed mine.
  27.  
  28. >Unfortunately for mono-lingual fools like myself, the program and all of
  29. >it's documentation is in German.  Further, it requires a GAL programmer of
  30. >the author's design.  While it is possible that the instructions required
  31.  
  32. Yeap... Got same problem here.  Can't even get that May 1992 Elektor
  33. article on building GAL programmer for the PC in town.  The only
  34. place in town decided not to carry it during the summer.  :(
  35.  
  36. I did got the full programming spec under NDA after a phone call to
  37. National Semiconductor.  Other companies simple laugh in my face.
  38. Good thing is the Nat. Semi call was my first, otherwise I was more
  39. than disappointed to try after a couple.
  40.  
  41. >Does anyone have any ideas?  Better solutions?  I'd hate to have to buy a
  42. >clone just so I could build hardware for my Amiga.
  43.  
  44. Well if you write my thesis for me I can probably release my EPROM
  45. programmer (full docs + source) and GAL (binary code only due to NDA). :)
  46. A job offer would probably do the same for me... :)  I am way too tied
  47. up these days to do anything.
  48.  
  49. Ask the German author whether or not he has an English version....
  50. (Mine still lacks the GAL assembler & disassembler, but sinceII can
  51. run IBeM for Nat Semi' OPAL JR (Free) I didn't bother writing mine.)
  52.  
  53. Try the EEPROM solution.  I know I would.  They are almost like RAM
  54. chip in pin outs and interfacing.  Writing to it is pretty simple too
  55. as some of them have built-in latches.  Just have to write data, and
  56. keep reading it until internal write is done (upper bit is inverted on
  57. read when it it not ready.) and write again.
  58.  
  59. Some stores have GAL programming service.  Cost $$$$ as I can't get it
  60. right without 4 - 5 iterations.
  61.  
  62. >Do NOT trust 'reply'!  wolf359.ustores.missouri.edu is BOGUS
  63.  
  64. That's why I am posting... Usually have problem with .uucp
  65.  
  66. K. C. Lee
  67. Elec. Eng. Grad. Student
  68.