21001 The operating system has not configured the device yet.
21002 The device loader failed to load a device.
21003 The system has run out of memory.
21004 The installation information file for this device is incorrect.
21005 There was a device failure due to the lack of an arbitrator. The device has requested a resource type for which there is no arbitrator.
21006 There is a conflict between this device and another device.
21007 No configuration can be performed on the device.
21008 The device loader for a device could not be found. For example, the installation information file for the device may refer to a missing or invalid file.
21009 The information in the registry for this device is invalid.
21010 This device is not present, not working properly or does not have all the drivers installed.
21011 The device has failed.
21012 One of the resource arbitrators failed. This can occur if the device is software configurable and it does not currently have a resource, if the system is out of resources, or if the device requests a resource and that resource is currently in use by another device that will not release the resource.
21013 The device failed due to a problem in the device driver.
21014 The device has a problem that may be resolved by restarting your computer.
21015 This device is causing a resource conflict.
21016 The device was not fully detected. When a device is not fully detected, all of its resources may not be recorded.
21017 The device is a multiple-function device and the installation information file for the device is providing invalid information on how to split the device's resources to the child devices.
21018 An error has occurred and this device needs to be reinstalled.
21019 The registry returned an unknown result.
21020 The VxD Loader returned an unknown result. There could a version mismatch between the device driver and the operating system.
21021 The device has a problem that may be resolved by restarting your computer.
21022 This device has been disabled.
21023 The device loader delayed the start of a device and then failed to inform the operating system when it was ready to start the device.
21024 This device is not present, not working properly or does not have all the drivers installed.
21025 This code occurs only during the first reboot in Setup and is not visible.
21026 The device failed to load or there may be a problem in the device driver, the file may be damaged.
21027 The portion of the registry describing possible resources for a device does not contain valid entries. The device is marked as configurable, but the configuration information in the information file is set to hardwired.
21028 The drivers for this device have not been installed correctly.
21029 This device has been disabled from hardware.
21030 The requested IRQ cannot be shared. This may occur when a PCI/EISA SCSI controller is sharing an IRQ that is also in use by a real- mode device driver that the operating system does not take over.
21031 None.
21032 Use Device Manager to remove the device and then the Add New Hardware tool in Control Panel to re-install the device.
21033 Use Device Manager to remove the device and then the Add New Hardware tool in Control Panel to re-install the device.
21034 Use Device Manager to remove the device and then the Add New Hardware tool in Control Panel to re-install the device.
21035 Use Device Manager to remove the device and then the Add New Hardware tool in Control Panel to re-install the device. If you continue to receive this error code, please contact the hardware's manufacturer for an updated installation information file.
21036 Use Device Manager to remove the device and then the Add New Hardware tool in Control Panel to re-install the device.
21037 To resolve this error code, see the "Troubleshooting Conflicting Hardware" topic in Windows Help.
21038 If the device works correctly, you do need not to perform any steps to correct the code. If the device does not work correctly, use Device Manager to remove the device and then Add New Hardware tool in Control Panel to re-install the device. If you continue to receive this error code and the device does not function properly, check with the hardware's manufacturer or the Microsoft Software Library for an updated driver.
21039 Use Device Manager to remove the device and then the Add New Hardware tool in Control Panel to re-install the device. If you continue to receive this error code, contact the hardware's manufacturer about an updated .inf file.
21040 Use Device Manager to remove the device and then the Add New Hardware tool in Control Panel to re-install the device. If you continue to receive this error code, contact the hardware's manufacturer for the proper registry settings.
21041 Make sure the device is attached to the computer correctly. Make sure all cables are plugged in fully and that all adapter cards are plugged into their slots fully.
21042 Use Device Manager to remove the device and then the Add New Hardware tool in Control Panel to re-install the device.
21043 To resolve this error code, see the "Troubleshooting Conflicting Hardware" topic in WindowsHelp.
21044 Use Device Manager to remove the device and then the Add New Hardware tool in Control Panel to re-install the device.
21045 Shut down Windows, turn off your computer, and then turn it back on.
21046 To resolve this error code, see the "Troubleshooting Conflicting Hardware" topic in Windows Help.
21047 Click the Resources tab in the device's properties to manually enter the settings.
21048 Use Device Manager to remove the device and then the Add New Hardware tool in Control Panel to re-install the device. If you continue to receive this error code, please contact the hardware's manufacturer about an updated installation information file.
21049 Use Device Manager to remove the device and then the Add New Hardware tool in Control Panel to re-install the device.
21050 Use Device Manager to remove the device and then the Add New Hardware tool in Control Panel to re-install the device.
21051 Use Device Manager to remove the device and then the Add New Hardware tool in Control Panel to re-install the device.
21052 Shut down Windows, turn off your computer, and then turn it back on.
21053 To enable the device, follow these steps: In Control Panel, double-click System. Click the Device Manager tab. Double-click the category for the device you want to enable, and then double-click the device. In the Device Usage box, click the check box for the configuration in which you want to enable the device. For example, click the Original Configuration (Current) check box to select it. Click OK, and then click Close. Shut down and restart your computer.
21054 Use Device Manager to remove the device and then the Add New Hardware tool in Control Panel to re-install the device.
21055 Make sure the device is attached to your computer correctly. Make sure all cables are plugged in fully and that all adapter cards are plugged into their slots fully.
21056 No resolution is necessary.
21057 Use Device Manager to remove the device and then the Add New Hardware tool in Control Panel to re-install the device. If you continue to receive this error code, check with the hardware's manufacturer or the Microsoft Software Library for an updated driver.
21058 Use Device Manager to remove the device and then the Add New Hardware tool in Control Panel to re-install the device.
21059 Click the Driver tab in the device's properties and then click Change Driver to update the driver.
21060 Resolve this error code by enabling or disabling the device in the computer's CMOS settings. Windows cannot override this setting. Please contact the computer's manufacturer for assistance with using the computer's CMOS setup program.
21061 Remove the real-mode driver that is using the same IRQ as this device. The real-mode driver may be loading in the Config.sys or Autoexec.bat file.
32769 Open the module\nOpen Module
32770 Starts Windows Control Panel\nControl Panel
32771 Starts the ScanDisk utility to check your drives\nScanDisk
32772 Starts the Defrag program to optimise your drives\nWindows Defrag
32773 Loads the online documentation\nDocumentation Page
32774 Various download links for the newest version\nUpdate Sandra
32775 Set or reset module options and information content\nModule Options
32778 Starts the system files editor\nConfiguration Editor
32779 Starts the system registry editor\nRegistration Editor
32780 Starts the system policies editor\nSystem Policy Editor
32781 Starts the TCP/IP protocol configuration program\nInternet Connection Editor
32782 Starts the backup program\nDisk Backup
32783 Starts the registry clean-up utility\nRegistry Clean-Up
32784 Starts the system monitor utility\nSystem Monitor
32785 Starts the System Analyst for Windows utility\nSAW
32786 Connect to a remote computer\nConnect
32787 Disconnect the current link\nDisconnect
32788 Change program options\nProgram Options
32789 Use id_addmodule
32790 Delete the selected module(s)\nDelete Module
