301 The sound card cannot be found with this DMA Channel. Check your settings and try again.
302 The sound card cannot be found with this Interrupt. Check your settings and try again.
303 The sound card cannot be found with port number %x. Check your settings and try again.
304 The MPU401 hardware cannot be found with this port. Check your settings and try again.
305 The DMA channel is in use by another part of the system.
306 Unexpeced error occurred during installation. Check your settings and try again.
307 The Interrupt is in use by another part of the system.
308 The MPU401 port address is in use by another part of the system.
310 The port is in use by another part of the system.
311 There was insufficient memory to install the driver.
312 The Sound Blaster 1.X driver is installed for use with your Thunder Card. For your card to work correctly with Windows, you should contact Media Vision for a driver specific to your card.
313 The Sound field port address is in use by another part of the system.
401 No suitable port is available for the Sound Blaster Card.
402 No suitable interrupt is available for the Sound Blaster Card.
403 No suitable DMA Channels is available for the Sound Blaster Card.
410 The Sound Blaster driver cannot be removed because of a registry access problem.
411 You have insufficient privilege to install, remove or configure the Sound Blaster driver
412 The Sound Blaster driver is busy. Try closing down volume controls and retrying. If this doesn't work remove the Sound Blaster driver, reboot and re-install it.
413 An unexpected error has occurred. Please try again.
414 DMA buffer size must be between 4 and %d.
415 A DMA Buffer of size %d Kilobytes could not be obtained, using %d Kilobytes instead.
499 Enable
500 Disable
501 I/O Address:
502 I/O &Address:
503 Continue
504 OK
505 Help for Continue
2131 Pressing the Continue button will test the port address of Sound Blaster 16.
2132 Pressing the Cancel button exits the configuration dialog and restores your configuration to its original state if possible.
2151 Pressing the OK button tests the configuration. If the Configuration is OK any changes that you made are saved. You will have to restart Windows for your changes to take full effect.
2152 Pressing the Cancel button exits the configuration dialog and restores your configuration to its original state if possible.
2171 Pressing the OK button tests the configuration. If the Configuration is OK any changes that you made are saved. You will have to restart Windows for your changes to take full effect.
2172 Pressing the Cancel button exits the configuration dialog and restores your configuration to its original state if possible.
2191 Pressing the OK button tests the configuration. If the Configuration is OK any changes that you made are saved. You will have to restart Windows for your changes to take full effect.
2192 Pressing the Cancel button exits the configuration dialog and restores your configuration to its original state if possible.
3001 Help for OK
3002 Help for Cancel
4130 Sound Blaster 16 Base I/O Address
4150 Sound Blaster 1.X and 2.0 Configuration
4170 Sound Blaster Pro Configuration
4190 Sound Blaster 16 Configuration
8143 This setting tells the system the port address at which your Sound Blaster card is located.
8150 This setting tells the system the interrupt that your Sound Blaster card is using.
8163 This setting tells the system the port address at which your Sound Blaster card is located.
8170 This setting tells the system the interrupt that your Sound Blaster Pro card is using.
8172 This setting tells the system the DMA channel your Sound Blaster Pro card is using.
8182 Pressing the Advanced button allows you to configure the DMA buffer size in Kilobytes. The default value of 4 Kilobytes is suitable for most purposes.
8183 This setting tells the system the port address at which your Sound Blaster Pro card is located.
8190 This setting sets the interrupt to use for your Sound Blaster 16 card.
8192 This setting sets the DMA channel your Sound Blaster 16 card will use for 8-bit digitized sound.
8194 This setting sets the DMA channel your Sound Blaster 16 card will use for 16-bit digitized sound.
8196 This setting tells the system the port address at which the MPU401 feature of your Sound Blaster 16 card is located.
8198 Disabling Auto-Configuration will let you choose the settings for the PnP card. Enabling it will cause the system to choose a conflict-free configuration.
8202 Pressing the Advanced button allows you to configure the DMA buffer size in KiloBytes. The default value of 16 Kilobytes is suitable for most purposes.
8203 This setting tells the system the port address at which your Sound Blaster 16 card is located.