OS/2 Shareware BBS: 11 Util/11-Util.zip/cfginfo7.zip/os2cfg16.dat

Text File | 1998-10-11 | 164KB | 3,951 lines

--------------------------------------------------------------------
   OS/2 CONFIG.SYS DESCRIPTION  -  Version 16 - Oktober, 1998
--------------------------------------------------------------------
 os2cfg16.dat is partly rewritten, as computers and their
 use have changed significantly since the release of
 CONFIGINFO in the year 1995.
 New commands by Klaus Staedtler ([e-mail])
 The informations here aren't complete.
 I'll maybe in the future add them when I have the time
 and get the informations (K.S.).
 Look also at Chapter 7. sample where the use of other IFS
 (Windows NTFS/FAT32 Apple HFS Linux EXT) is discussed
 Additionally I've added an instruction (see Chapter 11)
 how to install Warp 4 over an laplink cable,
 also good for networking over an parallel cable.
 To shorten the file I've moved all thanks at the end in
 Chapter 12.

 AS RICK MEIGS SEEMS TO SUPPORT CONFIGINFO NO MORE SEND YOUR
 IFORMATIONS PLEASE TO KLAUS STAEDTLER [e-mail] THANKS

 ENCOURAGEMENT:  This ASCII file may be freely distributed (and
 you're encouraged to do so) but you may not charge for the program,
 Further, the copyright notice may not be removed nor may the file
 be modified.  This file is Freeware (that means you can use it at
 no cost and pass it on to your friends), but it is not in the
 public domain.

 VIEWING FILE:  Regardless of what editor you use, for best
 results turn word wrap OFF and use a monospaced (like System
 Monospaced) font.

 PRINTING FILE:  In enhanced JB format for easy printing and
 viewing.  Print file using your favorite text editor.

-----------------------------------------------------------------
1.  CAUTION, WARNING AND DISCLAIMER.

 <<=CAUTION=>>  Because of the way in which OS/2s Enhanced PM
 editor (EPM.EXE) handles word wrapping and its restricted line
 length, using it to edit your config.sys file is unwise.  For
 best results, use OS/2s System Editor (E.EXE).

 <<=WARNING=>> If you plan on changing any line in your current
 config.sys file, please be sure to create a backup --BEFORE--
 you start experimenting!  This has saved me more than once.
 Remember, make the backup --BEFORE-- you change your config.sys
 file.  If you are viewing this information using CNFGINFO.EXE,
 use its backup option before you proceed any further.

 A procedure for restoring a damaged config.sys is included
 at in Chapter 8. of this file also an advise how to use
 multiple configuration. If you are using WARP, refer to your
 user manual on WARPs archive feature first.

 <<=TIP=>> For creating maintenance disks and partitions there
 is the very useful FREE IBM EWS Tool Bootdisk, the latest
 version is btos2915.zip

 If you plan to install warp 4 over an laplink cable there's
 an instruction in chapter 11.

 <<=TIP=>> There is also an very usefull FREE IBM EWS TOOL
 called Warp'n Go for handling the config.sys. It works
 normally only together with WARP 3. You can use it in WARP4
 when you insert in OS2VER the following lines:
 23=WARPNGO.EXE
 23=WARPNGO.DLL
 ATTENTION ! using Warp'n Go together with WARP 4 deletes the
 WARPCENTER Statement from SET AUTOSTART, but you can copy an
 Shadow of the WarpCenter into the Autostart Folder, this
 solves additionally some problems reported with WarpCenter
 started by the config.sys.

 <<=TIP=>> The new xfolder ver. 0.80 by Ulrich Moeller has
 also some settings for the config.sys. Available at
 http://www2.rz.hu-berlin.de/~h0444vnd/os2.htm
 For the moment the Beta has some problems so be careful.

 AS for OS/2 the both ini's OS2.INI and OS2SYS.INI are of great
 importance have an look on them also. There are the great FREE
 WPS-TOOLS by Henk Kelder for an backup, restore and check of
 these files, they can be found on many servers, bbs or on the
 authors homepage http://www.os2ss.com/information/kelder/
 latest version is WPTOOL26.ZIP
 For editing the INI Files you can make use of Regedit/2
 supplied with newer Fixpacks for Warp 4, there is also an somewhat
 faster FREE Editor called mINI by Kai Evers available at
 http://www1.stuttgart.netsurf.de/~kevers/

 <<=DISCLAIMER=>>  I CAN'T BE RESPONSIBLE FOR WHAT YOU DO WITH
 YOUR SYSTEM OR YOUR CONFIG.SYS FILE BASED UPON WHAT YOU MAY
 LEARN FROM THE INFORMATION PROVIDED IN THIS FILE.  EVERY EFFORT
 HAS BEEN MADE TO MAKE THIS FILE AS ACCURATE AS POSSIBLE, BUT
 NO WARRANTY OR FITNESS IS IMPLIED.  THE INFORMATION IS PROVIDED
 ON AN "AS IS" BASIS.  USE IT AT YOUR OWN RISK.

-----------------------------------------------------------------
2.  COMMENTS.

 This whole process started in 1992 when Rick Meigs began researching
 what many of the config.sys file commands were for. This ever
 growing file is the result of that ongoing research. It briefly
 describes most of the common and some of the more obscure
 commands.  Naturally, not all possible commands are listed
 (especially the many hardware device drivers), but there is a
 lot here for you to work with.  Version 6 was the first version
 updated for OS/2 2.1 and version 9 was the first updated for
 OS/2 Warp 3. Version 12 was the first updated for Warp 4.
 Naturally this information file can't be complete otherwise it
 would have the size of some Meg's and the people working at
 helpdesks would loose their job ;-)
 -----------------------------------------------------------------
3. IMPORTANT NOTE AND WARNING

 Unlike the DOS config.sys file which is read sequentially, OS/2
 reads the entire file before it invokes the commands listed.
 Therefore, except for several exceptions which have been noted,
 it really doesn't matter where a command is placed. On several
 of the "nets" and in a file called CNFGSORT.ZIP it has been
 suggested that if you organize your config.sys file in a certain
 way, you can significantly shorten the boot time of OS/2. I
 find this sorting to be of little or no help for the vast
 majority of OS/2 users.  Further, you can cause yourself
 problems if you do it incorrectly.  So be very careful and have
 a backup config.sys file ready.  Sorting your config.sys file
 DOES make sense for those who wish to organize it for readability
 and management purposes.
 Despite this warning of Rick I've added the last available version
 of Configsort (K.S.).

-----------------------------------------------------------------
4.  BEGINNING OF CONFIG.SYS FILE DESCRIPTION.

IFS=C:\OS2\HPFS.IFS /CACHE:512 /CRECL:16 /AUTOCHECK:CDE /F:2

 IFS stands for "Installable File System".  This OS/2 command
 installs the High Performance File System (HPFS).  The syntax
 is IFS=DRIVE:PATH\FILENAME,SWITCHES. There are three switches:

 /CACHE:nnn sets up a disk cache and its size. The default on
 most systems is low in my opinion.

 <<=Warning=>>  Keep this one truth in mind about cache size:
 an excessive cache takes memory available for programs and
 therefore could have a negative impact on overall system
 performance. But today, when most systems have 32MB+ the
 problem is more the restriction of the cache to 2MB.

 OS/2s Command Reference and other IBM sources indicate that
 the maximum cache size for HPFS is currently 2MB (2048), but
 IBM does not recommend using a cache larger than 1.5MB (1536).
 Personally, I have 16MB of RAM and have my HPFS cache set to
 the max: 2048.

 If this switch is omitted, the default is 10% of the available
 RAM on systems with more than 8MBs of RAM.

 <<=TIP=>> Use HPFS386.IFS if you have an license. It brings
 an significant performance boost into your system. If you
 plan to use HPFS386.IFS look for the serverfaq.zip at
 http://www.w-4.de/~tbaumann, unfortunately its only in german

 <<=TIP=>> At the end of the file is a detailed discussion how
 to set the cache with system less than 32 MB

 <<=TIP=>> For analyzing HPFS formatted drives there is the FREE
 Tool DFsee by Jan van Wijk, available at http://www.fsys.demon.nl
 DFSee can also undelete files and much more.

 <<=TIP=>> For undeleting files on HPFS Drives use the great IBM
 EWS Tool File Phoenix (Rel. 1.35) by Joe DiAdamo, available
 at many servers or BBS.

 <<=Tip=>> /QUIET will give you access to dirty partitions, too.
 It's mentioned in the readme.1st file of Warp4 FP5.
 There is an option /FORCE, I have seen it explained somewhere, but
 can't find out where.

 ========================== Table 1.0 ===========================

 You can get better performance from your system by using your
 available RAM in the most efficient and effective way.  Select
 the case that best describes the file system or amount of RAM
 you use.

 CASE 1:  You use only HPFS or only FAT, but not both.

                               HPFS only.         FAT only.
 System memory of at least:  Set CACHE to:    Set DISKCACHE to:

                     16 MB+           2048                 2048

 CASE 2:  You use both HPFS and FAT with HPFS active and FAT
 passive.

 System memory of at least:  Set CACHE to:    Set DISKCACHE to:

                     16 MB+           2048            512 -1024

 CASE 3:  You use both HPFS and FAT with HPFS passive and FAT
 active.

 System memory of at least:  Set CACHE to:    Set DISKCACHE to:

                     16 MB+           1024                 2048

 <<=NOTE=>>  For purposes of the table above, "active" and
 "passive" are descriptors for the way a partition is used.
 If it is seldom used, it is "passive."  If a lot of disk
 intensive I/O occurs on the partition, it is "active."

 ================================================================

 /CRECL sets the maximum record size for caching, from 2k to 64k
 in multiples of 2k with a default of 4k.  This parameter may not
 exceed 1/4 of the total cache size set with the /cache parameter.

 /AUTOCHECK:nn tells the system to check each drive noted to see if
 it was shut down properly.  If not, it will run CHKDSK on only the
 drives indicated.

 <<=Tip=>> /C will only run CHKDSK if the file system is dirty (new);
 /AuToChEcK (case-sensitive!!!) will make CHKDSK process locked drives
 (undocumented).
 You can speed up checking volumes situated on separate physical drives
 by using something like
 IFS=C:\OS2\HPFS.IFS /CACHE:2048 /CRECL:64 /AUTOCHECK:C
 and then running the CHKDSK's in parallel for each physical drive:
 start CHKDSK D: /F /AuToChEcK
 start CHKDSK E: /F /AuToChEcK
 and so on. Some have reported performance improvements of 250%.

 <<=NOTE=>>  If you place a plus sign (+) in front of any drive
 letter, the drive will be checked every time the system starts,
 even if shut down properly.

 <<=WARNING=>>  If you don't include the AUTOCHECK switch in this
 command, the system will not boot.

 /F:n indicates the level of CHKDSK to be used when automatically
 checking the drives at startup when AUTOCHECK is activated.  If
 no parameter is specifed, /F:2 is the default.

 <<=NOTE=>>  A /F:3 parameter will be ingnored unless you formatted
 your hard drive with the /L switch.

 <<=TIP=>>  If you are using only FAT partitions, then you should
 REM this IFS statement and save yourself some RAM.  How much?
 I've seen figures from 130k to 500k, but the HPFS.IFS file is
 136k in size.

 <<=TIP=>>  If you have drive partitions larger than 80MB, then
 HPFS should give you better performance than FAT.  On partitions
 of less than 80MB, most authorities indicate that there is only a
 small performance difference between HPFS and FAT.  Consider the
 following when comparing the relative merits of the HPFS versus
 FAT:  On large partitions of identical size, the HPFS will
 generally give you about 15% more space and improve performance
 by about 28%.

 <<=NOTE=>>  Lazy write is on by default.  If you want lazy write
 off, see the RUN=C:\OS2\CACHE.EXE command later in this file.

PAUSEONERROR=YES

 This command tells OS/2 to pause after it finds any error in your
 config.sys and displays an error message.  If you don't include
 this statement in your config.sys file, the default will be YES.
 This is generally the best choice since the error message will
 appear and scroll off the screen so quickly with a NO setting that
 you may not notice it.

PROTSHELL=C:\OS2\PMSHELL.EXE

 This OS/2 command tells OS/2 what program you want to use as the
 protect mode shell (the program that determines what your user
 interface looks like and how it operates.)  This is the first
 program OS/2 will execute.  PMSHELL.EXE is the program which
 initializes OS/2 Presentation Manager.  If you delete this line
 from your config.sys file, OS/2 will load PMSHELL.EXE by default.

 <<=NOTE=>>  There are several alternatives to PMSHELL.EXE.
 One is OS/2s own CMD.EXE.  If you replace PMSHELL.EXE with
 CMD.EXE, you will get a full screen OS/2 session only and will
 not be able to run PM programs.  A second alternative is
 TSHELL.EXE.  TSHELL is a text-based, protected-mode shell for
 OS/2.  Any one remember OS/2 1.x? TSHELL makes OS/2 look
 something like OS/2 1.0.  OS/2 1.0 did not have a graphical
 user interface.

 With TSHELL you can start and switch full-screen sessions only.
 These can be OS/2, DOS, or WINOS2 sessions depending on your
 systems configuration.  You use Alt+Esc to switch around
 sessions and Ctrl+Esc to pop up the task list.  But please note,
 like OS/2 1.0, there is no Presentation Manager. Thus, OS/2 PM
 applications will not work. You can download TSHELL.ZIP from
 most OS/2 BBSs.

SET COMMAND:  The SET command in the config.sys file sets up
 environment variables for the entire system.  These
 environment variables are stored by OS/2 in memory and are
 shared by any applications which calls on them.

 <<=TIP=>>  If you want to see what variables are set in your
 system, at an OS/2 command prompt type the word SET and press
 <enter>.  You'll get a list like the following:

     WP_OBJHANDLE=87103
     USER_INI=C:\OS2\OS2.INI
     SYSTEM_INI=C:\OS2\OS2SYS.INI
     OS2_SHELL=C:\OS2\CMD.EXE
     AUTOSTART=PROGRAMS,TASKLIST,FOLDERS
     RUNWORKPLACE=C:\OS2\PMSHELL.EXE
     COMSPEC=C:\OS2\CMD.EXE
     PATH=C:\OS2;C:\OS2\SYSTEM;C:\OS2\MDOS\WINOS2;
        C:\OS2\INSTALL;C:\;C:\OS2\MDOS;
     DPATH=C:\OS2;C:\OS2\SYSTEM;C:\OS2\MDOS\WINOS2;
        C:\OS2\INSTALL;C:\;C:\OS2\BITMAP;
     PROMPT=$E[1;33m[$P]$G
     HELP=C:\OS2\HELP;C:\OS2\HELP\TUTORIAL;
     GLOSSARY=C:\OS2\HELP\GLOSS;
     DIRCMD=/ON /P
     IPF_KEYS=SBCS
     KEYS=OFF
     SOMIR=C:\OS2\ETC\SOM.IR;C:\OS2\ETC\WPSH.IR;
     ...

SET USER_INI=C:\OS2\OS2.INI

 Tells OS/2 the name and locations of the file that contains
 your desktop setup information and the options saved from
 various OS/2 applications.  OS2.INI is the default file name.

 <<=NOTE=>>  OS2.INI is a critical file for the proper operation
 of OS/2 and should not be deleted or modified.  It is not an
 ASCII file and, if it should become damaged, cannot be modified
 with an ASCII editor.  You should consider backing up this file
 by using the CALL lines shown in HOW TO MAKE A BACKUP COPY OF
 YOUR INI FILES (if you are using CNFGINFO to view this file,
 select the How To Restore..." option) or with a program such as
 WPSBKUP out of the WPTOOLS by Henk Kelder. You can also use
 MAKEINI.EXE, which ships with OS/2, to build a new set of INI
 files. See your OS/2 documentation on how to do this.

 <<=TIP=>> For editing the INI Files you can make use of Regedit/2
 supplied with newer Fixpacks for Warp 4, there is also an somewhat
 faster FREE Editor called mINI by Kai Evers available at
 http://www1.stuttgart.netsurf.de/~kevers/

 <<=TIP=>> You can also make an seperate directory for your OS2.ini,
 e.g. SET USER_INI=X:\INI\OS2.INI, useful for reinstallations etc.

SET SYSTEM_INI=C:\OS2\OS2SYS.INI

 Tells OS/2 the name and location of OS2SYS.INI. This file
 tells OS/2 what kind of equipment your system uses. NOTE:
 OS2SYS.INI is a critical files and should not be deleted or
 modified.  It is not an ASCII file. You should consider backing
 up this file by using the CALL line shown in HOW TO MAKE A BACKUP
 COPY OF YOUR INI FILES (if you are using CNFGINFO to view this
 file, select the How To Restore..." option) or with a program
 such as WPSBKUP, part of the WPTOOLS by Henk Kelder.
 You can also use MAKEINI.EXE, which ships with OS/2, to build
 a new set of INI files.  See your OS/2 documentation on how
 to do this.

 This file remains open the entire time OS/2 is booted and
 operating. It only closes upon shut down.

 <<=TIP=>> For editing the INI Files you can make use of Regedit/2
 supplied with newer Fixpacks for Warp 4, there is also an somewhat
 faster FREE Editor called mINI by Kai Evers available at
 http://www1.stuttgart.netsurf.de/~kevers/

 <<=TIP=>> You can also make an seperate directory for your
 OS2SYS.ini, e.g. SET SYSTEM_INI=X:\INI\OS2SYS.INI, useful for
 reinstallations etc.

SET EPFINSTDIR=C:\OS2\INSTALL\

 Sets the path for the IBM-Installer

 <<=TIP=>> Make an own directory for the installer (e.g. SET EPFINSTDIR
 =X:\INI\) use not the default and move all files like epfi* to this
 directory, if you have to make an new installation of OS/2 there is an
 clean way to update or delete the programms who are using the IBM-Installer

SET OS2_SHELL=D:\OS2\CMD.EXE

 OS2_SHELL directs OS/2 to load the command line shell (CMD.EXE)
 when you ask for an OS/2 command line from the WpS.

 <<=WARNING=>>  Be careful with this line, OS/2 will not start
 without it.

 <<=TIP=>>  If you wish to run some other command line shell,
 such as 4OS2, change this line and the SET COMSPEC=C:\OS2\CMD.EXE
 line, substituting the appropriate EXE file for CMD.EXE.

 <<=TIP=>>  If you have a need to have a .CMD file invoked when
 you launch any OS/2 full screen or windowed session, just as
 AUTOEXEC.BAT is invoked for DOS sessions, modify this command
 line as shown below and it will cause AUTOEXEC.CMD to be invoked
 each time you start an OS/2 session.

SET OS2_SHELL=C:\OS2\CMD.EXE /k C:\AUTOEXEC.CMD

 You can choose any file name you wish for the CMD file.
 AUTOEXEC.CMD is used just as an example.

SET AUTOSTART=PROGRAMS,TASKLIST,FOLDERS,CONNECTIONS,LAUNCHPAD,WARPCENTER

 The AUTOSTART command contains a list of WpS components which
 will be started (or restarted) when the system is booted up.
 There are currently six possible options:

 PROGRAMS:  Tells OS/2 to start applications, that were running
            when the system was shut down, to restart.  This
            options will be ignored if SET RESTARTOBJECTS=NO.

 TASKLIST:  This parameter enables the OS/2 task list that appears
            when you press Ctrl+Esc.

 FOLDERS:   Opens the desktop and any other folder which was open
            when the system was shut down.

            <<=WARNING=>>  If you remove the FOLDERS statement,
            OS/2 will not open your desktop (which is a folder).

 CONNECTIONS:  This parameter restarts any network connections
               that were in use when the system was shut down.

            <<=NOTE=>>  This parameter can be removed if your
            system is not connected to a network.  Leaving it
            in your config.sys file will NOT cause any problems.

 LAUNCHPAD:  Restarts the new Lauchpad supplied with Warp.

             <<=NOTE=>> This parameter can be removed if you don't
             want to autostart the launchpad.

 WARPCENTER: Restarts the Warpcenter supplied new with Warp4

            <<=NOTE=>> can be removed if you don't want to
            autostart the WarpCenter

            <<=TIP=>> It is reported that in some cases the
            autostart of the WarpCenter by the config.sys crashes
            the WPS. If this appears, delete WarpCenter, and
            make instead an reference in the autostart folder.
            See also the WarpCenter SET options in this file

            <<=TIP=>> Don't use other activity monitors (e.g. like
            the one delivered with Describe, or Pulse) together with
            the enabled activity monitor in WarpCenter.

SETBOOT /T:5

 This command lets you set up the Boot Manager in OS/2.  There
 are a number of switches available including:

  /T:x  Number of seconds that the Boot Manager menu will
        remain on the screen before the default system starts.  A
        0 (zero) setting causes the menu to be bypassed.  A NO
        (as in /T:NO) causes the menu to remain displayed until
        a selection is made.

  /Q    Queries the currently set startup environment, and
        displays the default logical disk alias, timeout value,
        mode, and drive letter assignments for each system index.

  /X:x  Sets the system startup index to indicate the partition
        that the Boot Manager should start, where x is from 0 to 3.

 For complete information and other switches available, refer to
 the online OS/2 Command Reference.

SET RUNWORKPLACE=C:\OS2\PMSHELL.EXE

 This line tells the system what interface program is to be
 used.  In this case it is the Workplace Shell.

 <<=TIP=>>  If you want to run OS/2 with only a command line
 interface,  you can do so by changing this line to read
 SET RUNWORKPLACE=C:\OS2\CMD.EXE.  This brings OS/2 up without
 the WpS and gives you one screen session.  You can start other
 sessions using the START or DETACH command.  Otherwise,
 operated just like you were in DOS.  If you have started more
 than one session, switch between them using Alt+Esc.  For those
 who want the power of OS/2 and like to work only from a command
 line, give this a try.  I'm running in this mode as I write this
 as a test and it appears to work fine.

 <<=WARNING=>>  You can't perform a "shut down" from a command
 line.  To do a shut down type PMSHELL and press enter.  This
 starts the WpS.  Once the WpS is open, you should be able to
 perform a standard shut down.  You can also download one of
 several shut down programs available on most OS/2 specific
 BBSs.  I use one called SHUT32.ZIP.

 <<=TIP=>>  MSHELL.EXE is another alternative.  It is a simple
 mini shell for OS/2 that uses the replaceable shell
 architecture of the WpS.  MSHELL is a program launcher which
 provides one list of programs to start.  This list can be
 modified by creating a plain text file called MSHELL.INI. In
 addition to starting programs, MSHELL can save the desktop,
 interact with the spooler, and do a system shut down.

 MSHELL is IBM Employee Written Software and can be downloaded
 from most OS/2 specific BBSs or ftp.cdrom.com.

SET RESTARTOBJECTS=YES

 This command tells OS/2 what applications to start after you
 suspend operations with or without doing a shut down. If this
 statement is not in your config.sys, then the default is YES,
 i.e., start all objects that were running at the time of shut
 down or reboot.  Other options are:

  NO = do not start any applications that were running at time
       of shut down or reboot.

  STARTUPFOLDERSONLY = start objects only in the Startup
       folder.  This parameter is also handy for another
       purpose.  Lets assume you have one or more programs in
       your Startup folder and do a shut down without closing
       those programs.  If you have Restartobjects set to yes,
       OS/2 will restart the programs left open AND the Startup
       folder will start another copy of the same programs.
       Thus you will have two copies running.  Using this
       parameter eliminates this.

  REBOOTONLY = Start objects only if the OS/2 WpS is starting
       from a reboot (Ctrl-Alt-Del) or at power on.  Objects
       will not restart if the WpS is restarted as a result of
       its own error correction recycling.

 <<=TIP=>>  You can also circumvent the auto-starting of
 programs by holding down Left/Ctrl-Left/Shift-F1 all at the
 same time during boot.  It must be done right after the clock
 appears just before the desktop loads, but before any icons
 appear.

SET COMSPEC=C:\OS2\CMD.EXE

 This line identifies what OS/2 command line shell is to be used
 and its location.  In DOS, COMMAND.COM is equivalent to CMD.EXE.

 <<=TIP=>>  If you wish to run some other command line shell,
 such as 4OS2, change this and the SET OS2_SHELL=C:\OS2\CMD.EXE
 line, substituting the appropriate EXE file for CMD.EXE.

SET TEMP=C:\TEMP
SET TMP=C:\TEMP

 Sets the directory for temporary files

LIBPATH=.;C:\OS2\DLL;C:\OS2\MDOS;C:\;C:\OS2\APPS\DLL;

 Tells OS/2 where to locate Dynamic Link Libraries (DLLs).
 LIBPATH is similar to DPATH and PATH, but the statement can
 only be used in the config.sys file and OS/2 does not search the
 current directory for DLLs unless you include it in the LIBPATH
 statement.  You don't need to use the SET command with LIBPATH.
 It is not an environment variable.

 <<=TIP=>>  To reduce the search time, be sure that the various
 PATH statements contain the correct path to your program and
 other files.  You can also have OS/2 search the current directory
 by including a period "." right after the equal "=" symbol.   This
 causes OS/2 to look in the current logged directory first.

 One final item that will reduce search time:  Be certain that
 the PATH, LIBPATH and DPATH statements in the config.sys are
 arranged with the most frequently accessed sub directories
 listed first.

 <<=WARP TIP=>>  With Warp, IBM has introduced the ability to
 dynamically change LIBPATH using two new environment variables:
 BEGINLIBPATH and ENDLIBPATH.  These commands are most useful
 in CMD or BATCH files, but can be used in your config.sys.
 Any directories that appear in the BEGINLIBPATH variable are
 searched before directories in LIBPATH, and directories that
 appear in the ENDLIBPATH variable are searched after those
 in LIBPATH.  The correct syntax is SET BEGINLIBPATH=C:\OS2.

 <<=NETSCAPE TIP=>> Netscape must be in the first place of the
 Libpath, if you use Staroffice 4.0 check if thats correct, if
 not move the Staroffice Path behind Netscape and install
 Servicepak 2 or higher otherwise the Staroffice Browser wont
 function.

SET PATH=C:\OS2;C:\OS2\SYSTEM;C:\OS2\MDOS\WINOS2;C:\OS2\INSTALL;

 Just like in DOS, it tells OS/2 where to find programs.  For DOS
 sessions, set the PATH in your Autoexec.bat file.

 <<=WARNING=>>  Your path statement should contain at least the
 following directories:  \OS2, \OS2\MDOS, \OS2\SYSTEM.

 <<=TIP=>> In Warp4 peerinst.exe doesn't work correct if the path
 contains more than 256 Characters, if this happens make a copy
 of your config.sys and shorten the path temporarily

SET DPATH=C:\OS2;C:\OS2\SYSTEM;C:\OS2\MDOS\WINOS2;C:\OS2\INSTALL;

 This is an OS/2 command.  It tells OS/2 programs where to look
 for data files.  It is similar to the DOS APPEND command, but
 unlike APPEND, DPATH only works with programs designed to use
 it.

SET PROMPT=$E[1;33m[$P]$G

 Like the same DOS command, this line sets how your OS/2 command
 prompt will appear.  (This is for OS/2 only.  Set the DOS PROMPT
 default in your AUTOEXEC.BAT file.)  In the setting shown here,
 the command prompt will appear showing the current directory of
 the default drive enclosed in [] followed by the greater than
 symbol, i.e. [C:\]>.  Having brackets [] around the drive and
 directory information lets you quickly know when you are at an
 OS/2 command line verse a DOS command line.

 If you type PROMPT without a parameter, OS/2 will return its
 default prompt.

 Options include:

     $A = will substitute the '&' character
     $B = The | character
     $C = The open parenthesis (
     $D = Current date
     $E = ASCII code 27 (escape) so you can work with ANSI.
        See <<=TIP=>> below.
     $F = The close parenthesis )
     $G = The "greater than" > symbol
     $H = BACKSPACE over the previous character
     $I = Turns help line on
     $L = The "less than" < character
     $N = Default drive
     $P = Current directory of default drive
     $Q = The equal = character
     $R = will substitute the returncode for the previous command
     $S = The space character
     $T = Current time
     $V = OS/2 version number
     $_ = Carriage return or line feed

 <<=TIP=>>  You can also add ANSI control sequences to your
 prompt.  For example, to help me know visually whether I'm
 working with an OS/2 command line, I've add $E[1;33m to my
 prompt line, i.e. SET PROMPT=$E[1;33m[$P]$G.  This sets text
 to display in bold yellow characters. SET PROMP=$E[30;47m
 $E[K[$P] deletes the settings done by other programs and sets
 text to display black on white.

SET HELP=C:\OS2\HELP;C:\OS2\HELP\TUTORIAL;

 Tells OS/2 where the help files are located.  OS/2 will only
 look for its help files in the path shown.

SET GLOSSARY=C:\OS2\HELP\GLOSS;

 Tells OS/2 where Glossary and Master Help files are located.

SET MENUSTYLE=SHORT

 An undocumented SET command which controls the amount of
 information presented to you when you activate a pop-up
 menu.  For example, the standard pop-up menu on my OS/2
 desktop menu provides 13 menu items.  With this SET
 command in my config.sys, I only have 10 items.  The items
 not presented are Help, Create Shadow, and Find.

 <<=TIP=>> An Great enrichment for the menues, and a lot of
 other useful enhancements can be achieved by using the
 FREE XFolder, by Ulrich Möller, available at http://www2.rz.
 hu-berlin.de/~h0444vnd/os2.htm, current release is 0.80

SET DIRCMD=/ON /P

 An undocumented command that is the OS/2 equivalent of the DIR
 command in DOS.  Since DOS 5, you can tell DIR how to present
 file information.  To do this in OS/2, use the DIRCMD command.
 For example:  SET DIRCMD=/ON /P tells OS/2 to display the DIR
 information in alpha order and place a pause at the end of each
 page.

 <<=NOTE=>>  This is for OS/2 only.  Set the DOS default in your
 AUTOEXEC.BAT file.

   Options include:

   /A list files with specific attributes.  E.g. /AH list only
      hidden files.  Other options are S A & R.  If you place a
      negative (-) sign in front of your specified attribute,
      all files will list except those with the attribute
      specified.  E.g. /A-H-S will display all files except
      hidden and system files.
   /B list directories and files without heading and summary
      information.
   /F list files with the full drive and path information.
      Date, time and size are omitted.
   /L displays information in lowercase.
   /N lists files on a FAT drive in the same format used for a
      HPFS drive, i.e. date, time, size, name.
   /O list files according to sort option specified.  Sort
      options are:
         G = Display directories first.
         N = alphabetize by file name
        -N = reverse-alphabetizes by name
         E = alphabetize by extension
        -E = reverse-alphabetizes by extension
         D = by date, oldest first
        -D = by date, newest first
         S = by file size, smallest first
        -S = by file size, largest first
   /P pauses after a full screen of files is listed.
   /R displays long file names if applicable.
   /V shows the size seperated by an point e.g 1000.000kb
   /S searches and displays all directories.
   /W displays file names across the screen.  Date, time and
      size are omitted.

 <<=TIP=>> If you install Lotus SmartSuite 96 from a CDROM under WARP 4
 it will hang at about 85%. You can load the word processor separately
 but Freelance Graphics causes the hang. Lotus told that the cure was to
 REM out the SET DIRCMD= line in the config.sys, reboot, install, remove
 the REM and reboot.

SET SHELLHANDLESINC=nn

 This will increase the number of available filehandles, default 20, for
 the SHELL process with the specified number 'nn'.

 This setting is also inheritted by child-processes and can avoid some
 out-of-handles errors.

 <<=Note=>> This became more important because the later (Workplace) shell
 keeps more handles open for its own use, leaving less for started processes
 to open. This has caused problems in several compiler/build environments.

LASTDRIVE=H

 Specifies the maximum number of drives that are accessible.
 The value you specify with LASTDRIVE represents the last valid
 drive that is recognized.

SET IPF_KEYS=SBCS

 The character set for most languages can be represented as data
 using an 8-bit byte since their characters sets are each less
 than 256 characters.  These are called single-byte character sets
 (SBCS).  Languages such as Japanese (Kanji), Korean and Chinese
 (both Traditional and Simplified) can only be represented using
 two 8-bit bytes or 16-bits.  These are double-byte character
 sets (DBCS).

 This command tells the Information Presentation Facility (INF
 and help files) which type of character set is being used, i.e.,
 Single or Double Byte Character Set.  This is an environment
 variable.  Removing it from my system did not seem to have any
 impact.

SET SCKILLFEATUREENABLED=1

 ON, does the same as 1

 Allows to kill misbehaving programs with a Ctrl/left click on the WarpCenter
 task list (second button from the left)

SET SCKILLCONFIRMDISABLED=1

 ON does the same as 1

 Disables the the security question for the kill feature in Warpcenter
 use with care !

SET SCFINDUTILITY=C:\OS2\APPS\PMSEEK.EXE

 Replaces 'find objects' in WarpCenter by a faster and more useful program

SET SCUSEPRETTYCLOCK=1

 ON does the same as 1

 Changes the appearance of the WarpCenter clock

SET MENUSFOLLOWPOINTER=ON

 Enables cascading menus in Warpcenter like in Windows 95

SET PM_ASYNC_FOCUS_CHANGE=ON | ON x | OFF

 WARP 3 only, in Warp 4 these settings can be
 found unter [Systemconfiguration, System] on your Desktop

 The "SIQ" feature is new with FixPak XR_W017. It allows the user to
 take focus away from an application that is monopolizing the message
 queue.  When the FixPak is installed, the SIQ feature is disabled
 (OFF).
 The parameters to the SET command are:

 The default is OFF (disabled).

 To turn it on (enable) put the following in the CONFIG.SYS file and
 reboot:

 SET PM_ASYNC_FOCUS_CHANGE=ON

 To change the timeout value put the following in the CONFIG.SYS file
 and reboot:

 SET PM_ASYNC_FOCUS_CHANGE=ON x

 where x is in milliseconds (default is 2000 (2 seconds))

 SET QUEUE_SIZE_THRESHOLD=x

 Warp3 only (since FixPak 17), in Warp 4 these settings can be
 found unter [Systemconfiguration, System] on your Desktop

 puts the size of the message queue to x. Default was 100 prior
 to Fixpack #17, and 3000 from it.

 SET PM_DYNAMIC_DRAG=ON

 Warp 3 only (since FixPak 17), in Warp 4 these settings can be
 found unter [Systemconfiguration, System] on your Desktop

 enables (=ON) or disables (=OFF, default) the full window drag
 for PM windows. Don't use it with slow graphic cards.

PRIORITY_DISK_IO=YES

 This command determines whether programs running in the fore-
 ground have priority access to disks.  The default is YES.  If
 you want a program running in the background, like a BBS, to
 have equal access to your disks, then change this statement to
 NO.  If you change this command to no and then find that your
 communications program does not work, change back to yes.

PRIORITY=DYNAMIC

 OS/2 automatically assigns processing priorities to each thread
 of a program as it begins processing.  A thread running in the
 foreground will generally have priority over a thread running
 in background.  Thread priorities are adjusted, generally based
 upon how active they are, by OS/2 on an ongoing basis to make
 sure each thread has adequate processing time.  On the rare
 occasion that you need to run a program which must never change
 in priority, you should set PRIORITY=ABSOLUTE, otherwise, don't
 mess with it.

 <<=NOTE=>>  This command does not have to be in your config.sys.
 If it isn't, OS/2 defaults to PRIORITY=DYNAMIC.

 "To summarize: The highest priority thread always has the
 machine.  If there are two equally high threads, they timeslice
 having the machine.  Note that there are many Operating System
 threads, like the scheduler itself, that are higher priority
 than any program. Now, if PRIORITY=ABSOLUTE in the config.sys
 file, that's all there is to it.  But usually, PRIORITY=DYNAMIC,
 and OS/2 keeps gradually increasing the priority of a starved
 thread until it gets to run. Maxwait determines the maximum
 time, in seconds, before the scheduler intervenes to raise a
 low priority thread up high enough to run."

FILES=20

 This is a standard DOS command which sets the maximum number
 of files that DOS can access at the same time.  OS/2 sets the
 install default is 20, but some DOS programs may require an
 increased number.  The maximum parameter is 255.  The FILES
 command is for DOS only and has no effect on OS/2 sessions
 which can have up to 64,000 files open at the same time.

DEVICE=C:\OS2\TESTCFG.SYS
DEVICE=C:\OS2\BOOT\TESTCFG.SYS  <---- In Warp

 TESTCFG.SYS is used during the install process to test your
 systems configuration.  It is also used by the Selective Install
 process and during device driver installations.

 <<=NOTE=>>  Because this driver is used by the Selective Install
 process, it should not be deleted.

DEVICE=C:\OS2\DOS.SYS
DEVICE=C:\OS2\BOOT\DOS.SYS      <---- In Warp

 A device driver used to communicate between DOS and OS/2
 applications running on the same system.

DEVICE=C:\OS2\PMDD.SYS
DEVICE=C:\OS2\BOOT\PMDD.SYS     <---- In Warp

 OS/2 loads and uses this driver to provide pointer draw support
 along with POINTDD.SYS.

 <<=WARNING=>>  OS/2 will not start without this line in your
 config.sys file.

DEVICE=C:\OS2\BOOT\PAUSE.SYS /w:NNN

 where: NNN = seconds to wait (default = 30 seconds)

 Pauses the config.sys for an given time
 Useful for maintenance purposes
 the driver can be found at the IBM Device Driver Pak Online site.

 <<=TIP=>> Together with BASEDEV=IBM1S506.ADD the /W switch does
 the same

BUFFERS=30

 Tells OS/2 how many disk buffers to set aside.  Range is from 3
 to 100.  Each buffer takes up to 512 bytes of RAM.  The install
 default usually works well.  If you are using HPFS only, see
 <<=Tip=>> below.

 Disk buffers are blocks of memory set aside by OS/2 for use in
 reading and writing blocks of data.  For example, if a program
 wants to change 80 bytes of a file, it needs to read the 512
 byte sector that contains the original data, change the infor-
 mation and then write the corrected 512 byte sector back out.
 A "buffer" is the 512 byte temporary staging area for this
 partial sector operation.  According to a source at IBM, "OS/2
 allows multiple simultaneous I/O operations to be queued up for
 both diskette and hard disk.  Each 'concurrent' operation may
 need a buffer.  If there are not enough buffers, overlap can be
 inhibited.  Because OS/2 has more 'simultaneous' queued I/O
 than DOS, it needs more buffers."

 <<=TIP=>>  Generally, if you are running FAT on one or more of
 your hard drives, you can speed up your system by increasing
 the number of BUFFERS.  But, keep in mind that as you increase
 the number, you reduce available memory.  Be careful about using
 a lower number unless you only have 4MB of RAM.  With 4MB of RAM
 you may wish to set BUFFERS to 20.

 <<=TIP=>>  If you are using only HPFS (i.e., no FAT partitions),
 try setting BUFFERS to 3.  With HPFS you generally don't need
 BUFFERS.  Remember that 3 is the minimum parameter.  If you set
 BUFFERS to 1 or 2, OS/2 will default to 30 since 1 and 2 are out
 of range.  There is one exception to this tip.  If you access
 your floppy disks a lot, then a reduced BUFFERS setting could
 impact floppy performance.

IOPL=YES

 When set to YES, this command lets programs that need to bypass
 OS/2 (and its device drivers) and work directly with hardware
 devices, to do so.  One example is Lotus 123/G.  YES means
 that all programs can access the hardware directly.  NO means
 that no program can access the hardware directly.  YES is the
 default and is generally best, since its hard for most of us to
 know when a program is written is such a way as to need direct
 access to hardware.

 IOPL stands for Input/Output Privilege Level.

 <<=TIP=>>  You can also specify a list of programs that are
 allowed to work directly with the hardware.  For example,
 IOPL=WS.EXE,123.EXE would allow only these two programs to
 access hardware directly.

RUN=C:\OS2\CACHE.EXE /MAXAGE:7500 /DISKIDLE:60000 /BUFFERIDLE:60000

 This line runs CACHE.EXE which allows you to modify the
 parameters for the HPFS cache.  CACHE.EXE is only used for
 HPFS partitions.  (The DISKCACHE command sets up a cache for
 FAT.)  There are four switches for CACHE.EXE:

   /LAZY:  Determines if lazy writes is ON or OFF, that is,
     whether the contents of the cache will be written to your
     hard disk immediately (/LAZY:OFF) or when your hard disk
     is idle (/LAZY:ON).  The default is ON.  I like lazy
     writes ON because it improves performance, but keep in
     mind that since the system delays writing data to your
     hard disk, you can lose data if your system should crash.
     In the config.sys file line above no switch is specified
     therefore the default remains in effect, which is ON.

     <<=TIP=>>  Lazy writes can also be turned ON or OFF at an
     OS/2 command prompt.

     <<=WARNING=>>  If you include the /LAZY switch, then the
     CACHE statement will IGNORE ALL OTHER SWITCHES in the
     line.  Therefore, if you want to turn lazy writes off (or
     on) and also change some other parameter, you will need
     two RUN statements.

     <<=TIP=>> This conform with all online
     document i've read for OS/2. But it is not true. On my
     system I have a line RUN=D:\OS2\CACHE.EXE /LAZY:12
     /BUFFERIDLE:60000 /DISKIDLE:60000 /MAXAGE:64000 /READAHEAD:1
     And it works very fine. Trying to separate this line into
     two statements causes my system to stop during boot with
     the message "please press a key to continue".

     <<=WARNING=>>  There is a bug in OS/2 version 2.1 which
     does not appear to have been fixed in Warp.  You
     can't turn lazy writes off from the config.sys file.  The
     WpS always turns lazy writes ON when it loads regardless
     of what your CACHE.EXE command sets.  So, if you want lazy
     writes off, you will need to run the CACHE command AFTER
     the WpS starts.  Create a CMD file to turn it off and place
     it in your Startup folder.  The WpS has already done it's
     thing when the objects in the Startup folder are opened.
     You can also turn it off from a command prompt.

   /MAXAGE:  Sets how long data waits in the cache before it is
     moved to another area of the cache where less used
     information is stored, or how long data waits in the
     cache before it is written to the hard disk.  It is
     expressed in milliseconds.  The default is 5,000 or about
     5 seconds.  In the config.sys file line above, the wait
     is set at 7,500 milliseconds or about 7 1/2 seconds.

   /DISKIDLE:  Sets how long your hard disk must be idle before
     it will accept data from the cache.  Express in
     milliseconds and the default is 1,000 or about one
     second.  The minimum value must be greater than the value
     specified in the BUFFERIDLE parameter.  In the config.sys
     file line above no switch was specified so the default
     remains in effect.

   /BUFFERIDLE:  Sets how long the cache buffer must be idle
     before its contents MUST be written to your hard disk.
     Express in milliseconds and the default is 500 or about
     1/2 second.  In the config.sys file line above no switch
     was specified so the default remains in effect.

 According to one source at IBM, there are two other
 undocumented parameters.

   /DIRTYMAX:  The threshold number of dirty buffers before
     immediately flushing of least recently used (LRU) data
     blocks.

   /WRITECACHE:  The threshold number of bytes that HPFS will
     cache for a lazy write.

 <<=NOTE=>>  The HPFS IFS config.sys file line sets up the
 cache and uses the system defaults.  This config.sys file
 line is only used to modify the cache parameters.

 <<=TIP=>>  You can check to see what parameters the HPFS cache
 is currently set at by going to an OS/2 command prompt and
 keying in the word CACHE and pressing the enter key.

 <<=TIP=>>  Table 2.0 contains information on optimum settings
 for each of the main parameters.
 ========================= Table 2.0 ===========================

   Parameters:             LAZY WRITES               /LAZY:ON
                                MAXAGE                 >7,500
                              DISKIDLE                 60,000
                            BUFFERIDLE                 60,000
 ===============================================================
 <<=TIP=>> Warp 4 Cache info direct from "Mr HPFS" Doug Azzarito of
 IBM - Austin

 Doug: CACHE.EXE shouldn't be used in CONFIG.SYS, it should be put
 in STARTUP.CMD. If you type CACHE ? you will see:

     The specified option, ?, is incorrect.
     Correct usage: cache [OPTIONS]
     where OPTIONS is one or more of:
      -DISKIDLE:n         Sets disk-idle time before write to n
                          milliseconds.
      -MAXAGE:n           Sets maximum age of cache buffer to n
                          milliseconds.
      -BUFFERIDLE:n       Sets buffer idle time to n milliseconds.
      -Lazy:ON|OFF|n      Turns lazy writing on, off or set to 'n'
                          lazy writers.
      -READAHEAD:ON|OFF|n Turns read ahead on, off or set to 'n'
                          read ahead workers.

     The new parameters are LAZY:n (in Warp 3 it only allowed ON & OFF)
     and -READAHEAD. The -n in READAHEAD isn't used, but will accept 0
     or 1, and turn that into an ON or OFF.

 Ron: Do you know of the /DirtyMax and /WriteCache switches?

     Doug: They're not very useful - I use them in testing only.
     The DIRTYMAX switch sets a maximum number of dirty buffers -
     if this limit is reached, the lazy-writer wakes up and cleans
     up the cache. It is set at 80% of the cache.
     WRITECACHE is a parameter that sets the maximum size of a WRITE
     that will be put in cache. It is set to the maximum size of a
     write operation (64K).

DISKCACHE=D,LW,32,AC:CD+E

 If you are using one or more FAT partitions on a hard drive,
 this command sets up a disk cache for those partitions.  The
 default cache size used by OS/2 during installation is based on
 how much RAM your system contains.  See Table 3.0.  The minimum
 cache size is 64k and the Maximum FAT cache size is 14MB.

 <<=IMPORTANT NOTE=>>  Under Warp, during installation the
 letter "D" is used instead of the usual numeric value.  On the
 "nets", several users have reported that their disk I/O was
 significantly reduced when they replaced the "D"  with a value
 as was the case in OS/2 2.x.  I suggest you change this setting
 based on the optimum cache sizes as shown in Table 1.1 above.
 If you leave the "D" setting, then OS/2 will set your FAT
 diskcache based upon the amount of RAM you have as follows:

        7 or 8MB of RAM, "D" is set to 512k; and
        more than 8MB, "D" is set to 10% of RAM.

 <<=NOTE=>>  This command is for hard drives only.  DISKCACHE
 does not cache FAT based floppy drives.

 <<=TIP=>>  If you have the RAM, increase the size to improve
 system performance, but don't get carried away by using to much
 of your RAM; this can hurt performance.  See the information on
 optimum cache sizes contained in Table 1.1 which is repeated
 below.

 <<=TIP=>>  If you are only using HPFS, then you should REM
 this statement and save 64k of RAM (don't delete, you may need
 or want it later).  If you have a FAT partition on your hard
 drive and you REM this statement, OS/2 will automatically set
 up a 64k cache by default.

 ========================= Table 3.0 ===========================

 If you have formatted your hard drive(s) with only FAT partitions,
 the default cache size in this statement will be that noted under
 ONE FILE SYSTEM.  If you have both FAT and HPFS partitions,
 then OS/2 defaults to the cache size noted under TWO FILE SYSTEM.
 The file system which uses the greatest amount of your disk space
 gets the larger default value.

   MEMORY SIZE IN MB      TWO FILE SYSTEM         ONE FILE SYSTEM*
        10 - 16               512/512                 1024
        17 - 32               1024/1024               2048

 * Defaults in Warp are different and are shown as the second
   number.  On systems with more than 8MBs of RAM, the default
   is 10% of available RAM to a maximum cache of 4MB.

 <<=TIP=>> See the end of the file for an detailed discussion how
 to set the cache for less powered systems.

 ===============================================================

 LW:  Enables lazy writes.  If you don't want lazy write enabled,
 then remove ",LW".

 <<=NOTE=>>  Lazy-writing provides significant performance
 improvements to your system.  If you disable this feature, the
 performance of your system will suffer.

 32:  Sets the threshold size.  It is express in number of sectors
 which are 512 bytes each.  Data requests from your disk that are
 larger than this number will not be cached.  The default is 4.
 Thirty two (32) is said to be an optimum number.  One hundred
 twenty eight (128) is the maximum allowable.  This setting has
 no impact on RAM.

 AC:CD+E:  If you want CHKDSK to automatically check any partition
 after an improper shut down, then add this switch to end of the
 DISKCACHE command:  AC:n where n is the partition(s) to check,
 e.g. AC:C.  If you add a + (plus) sign before any drive letter,
 OS/2 will automatically run CHKDSK on that drive each time
 you boot.

 =================== Table 1.1 Repeated ========================

 You can get better performance from your system by using your
 available RAM in the most efficient and effective way.  Select
 the case that best describes the file system or amount of RAM
 you use.

 CASE 1:  You use only HPFS or only FAT, but not both.

                               HPFS only.         FAT only.
 System memory of at least:  Set CACHE to:    Set DISKCACHE to:

                     16 MB+           2048                 2048

 CASE 2:  You use both HPFS and FAT with HPFS active and FAT
 passive.

 System memory of at least:  Set CACHE to:    Set DISKCACHE to:

                     16 MB+           2048            512 -1024

 CASE 3:  You use both HPFS and FAT with HPFS passive and FAT
 active.

 System memory of at least:  Set CACHE to:    Set DISKCACHE to:

                     16 MB+           1024                 2048

 <<=NOTE=>>  For purposes of the table above, "active" and
 "passive" are descriptors for the way a partition is used.
 If it is seldom used, it is "passive."  If a lot of disk
 intensive I/O occurs on the partition, it is "active."

 ===============================================================

MAXWAIT=3

 This command sets the longest period a program will have
 to wait to execute before OS/2 ups its priority.  This makes
 sure that no program is put on hold forever while some other
 program hogs the system.  You can set MAXWAIT from 1 to 255
 seconds.  The default is 3 seconds.

 <<=TIP=>>  When running heavy background programs, such as a
 BBS, change the setting to 1, i.e. MAXWAIT=1.  This will keep
 the BBS software or other background programs running at top
 speed.  For general use, it appears that setting MAXWAIT=2
 makes the system a little livelier.

 <<=NOTE=>>  MAXWAIT only has an effect if PRIORITY=DYNAMIC.

 <<=NOTE=>>  The smaller the number you use, the more system
 overhead there will be.

MEMMAN=SWAP,PROTECT

 OS/2 can run more programs and use more data than can actually
 be stored in memory at any given time.  This is done by swapping
 large amounts of memory to your hard disk and then reading the
 data back into memory when needed.  This is called virtual memory.
 For example, if you have 4MB of memory you will see lots of disk
 activity while you are working with your system.  A lot of this is
 OS/2 swapping memory to and from your hard disk.  Lots of memory
 swapping slows down your system and can cause your hard disk to
 fragment quicker than normal.

 The MEMMAN command controls the swap process.  The syntax is
 MEMMAN=s,m,PROTECT,COMMIT where s=SWAP or NOSWAP; m=MOVE or NOMOVE.
 The default is to have virtual memory on.  To turn off virtual
 memory, which is NOT recommended, the config.sys file line should
 read:  MEMMAN=NOSWAP.  See <<=CAUTION=>> below.

 PROTECT allows the allocation and use of protected memory for
 certain DLLs.  This is done to protect those DLLs from being
 trashed by an errant program.  Unless you are a programmer who
 needs this set to NOPROTECT, leave the default.

 <<=NEW PARAMETER=>>  A new parameter with version 2.1 is COMMIT.
 With this parameter included, OS/2 will allocate space in the swap
 file whenever a program commits memory, i.e., a page in the swap file
 is allocated for every page of memory committed by a program, even
 if the data never actually gets swapped out.  Your system should be
 more stable, but it will be slower also, since your swap file will
 grown when it doesn't have to.  If you use this parameter, increase
 the size of your SWAPPER.DAT file (see SWAPPATH line below) by
 the amount of memory you are likely to use when using the COMMIT
 parameter.  Most people "in-the-know" suggest that COMMIT not be
 used unless it is required by 16-bit OS/2 applications.

 <<=TIP=>>  You can also use the COMMIT parameter another way.
 Without COMMIT set, the minimum free noted in you SWAPPATH
 specified the point at which OS/2 gives you a message warning that
 your disk space is running low.  When you set COMMIT, the minimum
 free value noted in your SWAPPATH statement becomes the amount of
 hard disk space that will always remain free on the swap file
 partition.  Thus, with COMMIT set, you can never run out of disk
 space on your swap file partition.

 <<=CAUTION=>>  When messing with the MEMMAN line, I changed it to
 MEMMAN=NOSWAP.  As a result, I had to boot from my OS/2 installa-
 tion disk and recover my backup config.sys file to get the system
 to boot.  According to Blake Stover, "The reason MEMMAN=NOSWAP,
 PROTECT chokes is because of the hat tricks OS/2 does while
 loading the WpS, Desktop, Bitmaps, Folders, Cache buffers, MMPM/2,
 etc..  OS/2 likes to load all of these, then swap or discard the
 inactive code.  If there is no where to swap to it dies during
 boot, unable to initialize the resources it needs.  NOSWAP,PROTECT
 should only be used for boots from floppy to do maintenance, in
 most cases.  (People who use TSHELL on a machine with a good
 amount of RAM may also use it to speed operations).  IBM does
 not recommend that you set MEMMAN to NOSWAP unless you have more
 than 8MB of RAM.

 <<=NOTE=>>  The MOVE/NOMOVE parameter is only provided for
 OS/2 1.x compatibility.

 <<=NOTE=>>  NOPACK PARAMETER.  When OS/2 initially loads a 16-bit
 OS/2 application, it packs the segments into pages and copies
 them to the swap file for faster recovery when needed.  This can
 be disabled by using the NOPACK option on the MEMMAN line. How-
 ever, the performance decrease and larger working set will rarely
 offset the potential of a reduced swap file size.

 <<=NOTE=>>  DELAYSWAP.  No information at this time. SWAPDOS and
 NOSWAPDOS parameters from OS/2 1.x are not valid in OS/2 2.0 and
 later.

SWAPPATH=C:\OS2\SYSTEM 512 4096

 OS/2 can allocate more memory than it actually has available.
 It does this by swapping memory to a hard disk file called
 SWAPPER.DAT.

 The syntax is SWAPPATH=DRIVE,PATH,mmm,nnn where DRIVE,PATH is
 the location where you want the SWAPPER.DAT file to be placed and
 mmm is a number from 512 to 32767 which specifies how large the
 SWAPPER.DAT file can grow before it stops consuming hard disk
 space.  The size is stated in the negative.  In other words, if
 you have the mmm set to 512, then the SWAPPER.DAT file can grow
 until there is only 512k left on your hard disk.  The variable
 nnn is the starting size of the SWAPPER.DAT file.

 <<=TIP=>>  When your swap file grows beyond the initial size you
 have specified, OS/2 starts to manage the swap file.  This
 increased overhead can negatively impact your systems performance.
 Therefore, if your swap file always exceeds its initial size,
 consider increasing the files initial size.  For example, if your
 swap file usually grows to 8MB, set the initial size of 8MB.

 <<=TIP=>>  Normal operation of OS/2 can involves considerable
 disk activity as operating system functions are loaded and pages
 are moved in and out of the swap file.  Here are a couple of tips
 to improve performance.  (1) Consider dedicating a separate
 partition for the swap file.  This helps avoid fragmentation of
 the swap file, because other files will not be added or deleted
 from the dedicated partition.  (2) If you have both FAT and HPFS
 partitions, put the swap file on the HPFS partition to take
 advantage of the better performance of HPFS.  (3) If you have a
 system with two hard disk controllers, put the swap file on a disk
 managed by the least used controller.  (4) Keep your swap file on
 the MOST used partition of the LEAST used hard drive.

 <<=WARNING=>>  Never put your swap file on a networked drive.

 <<=NOTE=>>  Your swap file will grow (in 1MB increments), but it
 also shrinks when two conditions are met.  One, when the amount
 of free space in the swap file is greater than 1.5MB, the swap
 file will be compressed during system idle time.  (It will not
 shrink if there is a constant "hit" on the drive by a program such
 as a swap file monitor.)  Two, during the compression, free space
 is moved to the end of the swap file.  When this free space at the
 end of the swap file exceeds 1MB, the swap file will be shrunk.

 <<=NOTE=>>  See the discussion of the new COMMIT parameter for the
 MEMMAN config.sys line including the <<=TIP=>>.

 <<=WARP NOTE=>>  Your swap file in Warp will be larger than in
 earlier versions of OS/2.  This is normal.  The most significant
 change that has been made is how system DLL's get loaded and what
 is now valid data for swapping.  System DLL's include:  DISPLAY,
 SOM, PMMERGE, PMWP, DOSCALL1, PMATM, PMMLE, IBMDEV32, PMCTLS,
 PMSPL, IBMVGA32, PMGPI, and PMVIOP.

 In the previous versions of OS/2, dll code was never copied to
 the swapper file.  In WARP, code for system dll's can be written
 to the swapper file and, in adition, during boot, PMMERGE,
 DOSCALL1, PMGPI, PMWP and PMVIOP will be swapped out.  This
 means that there will be an overall increase in swapper size.
 This was done to increase overall system perfomance.

BREAK=OFF

 For DOS programs only.  Many DOS programs can be stopped by
 holding down the Ctrl key and then pressing the Break key.
 BREAK controls how quickly DOS programs stop when you interrupt
 them with the Ctrl+Break sequence.  If BREAK=OFF, DOS will stop
 the program only when the programs next reads a character from
 the keyboard or writes to the screen or printer.  With BREAK=ON,
 DOS will check for the Ctrl+Break on a more frequent basis.
 Remember that this extra checking can make your DOS programs run
 slower.

THREADS=256

 OS/2 programs can have several different processes running at
 the same time.  These are called threads.  This command sets
 the maximum number of threads (from 32 to 4095 in OS/2 2.x and
 from 64 to 4095 in Warp 3) that OS/2 can run at the same time.
 If this command is not included in your config.sys file, OS/2
 will default to 64.  Jim Gilliland commented on what happens
 if OS/2 runs out of Threads:  "If an application tries to start
 a new thread, and OS/2 has all of its threads  already in use,
 then OS/2 will generate an error.  It may result in a popup, or
 it may return the error information to the application."

 <<=TIP=>>  If you have more than 8MB of RAM and run lots of OS/2
 specific programs, you may be able to improve system responsive-
 ness by increasing the number of threads.  Why?  Because well
 written OS/2 programs will use threads to improve program per-
 formance.  Therefore, the more well written OS/2 programs in use,
 the more threads that could be needed.  But still keep in mind
 that this only holds true only when you are using a fair number
 of OS/2 specific programs at the same time.  Even when I opened
 the Enhanced Editor, AmiPro for OS/2, ZOC, and KWQ Mail/2, I was
 only using 57 threads.  The most threads I've ever recorded at
 one time was 76.

 <<=SERVER NOTE=>>  On a server it is generally considered better
 to have 512 threads.

PRINTMONBUFSIZE=2048,134,134

 This command sets the size of the print buffers for your
 parallel ports.  The syntax is PRINTMONBUFSIZE=LPT1,LPT2,LPT3
 where LPT1 is the buffer size for the parallel port LPT1, LPT2
 is the buffer size for LPT2 and LPT3 is the buffer size for
 LPT3.  The default and minimum is 134 bytes and the maximum is
 2048 bytes.

 <<=Note=>>  You must define a buffer for LPT2 and LPT3 even if
 you don't use these ports.  You will get an error message at
 start up if you don't.

 <<=TIP=>>  You may be able to improve printer throughput by
 increasing buffer size.  I have my LPT1 set to 2048.  On systems
 with less than 6MB of RAM, don't increase the size of these
 buffers.

 <<=TRIVIA=>>  Ever wonder where IBM got a parameter like 134?
 I did and Lynn Nash passed along the following in response to
 my question:

 "Obviously you have no background on the big iron or it has
 disappeared into historical memory :-).

 "Mainframe line standard of 132 columns plus 2 for carriage
 return and line feed characters.  That is why all the wide
 carriage dot matrix printers also had 132 column lines, to be
 able to use that wide green bar paper. Anyone that had an early
 Okidata 83 dot matrix even had an electronic format tape, but
 that is a story for another time."

COUNTRY=001,C:\OS2\SYSTEM\COUNTRY.SYS

 Customizes your system for the country you wish to use.  It
 establishes which defaults to use when it comes to decimal
 separators, date and time formats, currency symbols, etc.  The
 syntax is COUNTRY=xxx,PATH,FILE NAME.  xxx is a three-digit code
 number that tells what country to use.  The number is usually
 (but not always) the same as the international telephone dialing
 prefix for the country desired. If in doubt consult your OS/2
 online-reference.

SET KEYS=OFF

 When using the command line, KEYS tells CMD.EXE whether to
 remember previous keystrokes so they can be recalled with the
 up arrow key.  OS/2 maintains a 64k buffer for storing
 keystroke history.  KEYS can be ON or OFF.  To find out
 whether KEYS is on or off, simply type KEYS without a
 parameter from an OS/2 command prompt.  To list all of
 KEYS commands, type KEYS LIST.

 <<=NOTE=>>  With KEYS=ON, ANSI extended keyboard sypport in
 OS/2 sessions will be disabled by the system.

SET SOMIR=C:\OS2\ETC\SOM.IR;C:\OS2\ETC\WPSH.IR;C:\OS2\ETC\WPDSERV.IR;SOM.IR

 SOM is an acronym for IBMs System Object Model.  OS/2s object
 orientation is based upon this technology and in Warp, the
 Workplace Shell is built on SOM Version 2 with Distributied
 SOM enabled.  This SET statement sets the path to various IR
 files.

SET SOMDDIR=C:\OS2\ETC\DSOM

 SOM is an acronym for IBMs System Object Model.  OS/2s object
 orientation is based upon this technology and in Warp, the
 Workplace Shell is built on SOM Version 2 with Distributied
 SOM enabled.  This SET statement sets the path to the DSOM
 directory.

SET DELDIR=C:\DELETE,512;

 To use OS/2s UNDELETE command, you must first establish a
 directory to store the deleted files.  To do this, create
 a directory called DELETE on each partition you have and then
 remove the "REM" from this config.sys file line.

 This command points OS/2 to the directory you created to place
 deleted files in.  It also indicates the maximum K bytes of
 files that will be stored in the DELETE directory.  If the
 number of deleted files exceeds the maximum K bytes that you
 specified, then files are automatically removed from the
 directory on a first-in-first-out basis.

 <<=WARNING=>>  Using this command will have an impact on system
 performance.  File operations in particular will be slower.
 I don't recommend the use of DELDIR at all.

 <<=TIP=>> Better make use of the File Phoenix 1.35 by Joe
 DiAdamo an FREE IBM EWS Tool available at many servers and bbs.

 <<=TIP=>> There is also an McIntosh like Trashcan by Kai
 Sommerfeld (with sounds, bells and whistles), and FREE
 ones by Andrea Henicke and Mark Kimes (unfortunately with
 very ugly icons that can't be substituted, they also don't
 seem to work correct together with Warp 4)

SET HOSTNAME=xyz.ab

 Sets the variable for the Hostname

SET USE_HOSTS_FIRST=1

 Enables the loopback-interface needed by many programs (e.g. Visual
 Age for Java, XFREE86) or if an nameserver works in your LAN.
 You also have to edit the file x:\mptn\bin\setup.cmd and insert
 after all other 'ifconfig' statements the line
 'ifconfig lo 127.0.0.1', then generate an file named 'hosts' in the
 directory x:\mptn\etc or x:\tcpip\etc and insert 127.0.0.1 localhost;
 the correct directory can be found out by typing the command
 'echo %etc%' at an command line

 <<= TIP =>> the necessary configuration can also be done by using the
 TCP/IP Notebook.

SET LOTUS_BROWSER=X:\Path\Browser.exe

 To make Lotus Freelance for Warp 4 use the web browser you want
 you'll need to set this, otherwise Netscape will be used

BASEDEV=

 BASEDEV installs a base device driver used by OS/2 when it is first
 started.  The statement cannot contain either a drive or path
 because OS/2 cannot process such information at the stage at which
 these statements are loaded.  These base device drivers include
 (not all delivered or available drivers are listed):

 PRINT01.SYS supports attached printers on non-Micro Channel PC's.
 PRINT02.SYS supports attached printers on Micro Channel PC's.
 IBM1FLPY.ADD supports diskette drives on non-Micro Channel PC's.
 IBM2FLPY.ADD supports diskette drives on Micro Channel PC's.
 IBM2SCSI.ADD supports SCSI disk drives on Micro Channel PC's.
 OS2SCSI.DMD supports non-disk SCSI devices.
 IBM1S506.ADD supports non-SCSI disk drives, non-Micro Channel PC's.
 OS2DASD.DMD is a general purpose driver for disk drives.
 IBM2ADSK.ADD supports non-SCSI disk drives on Micro Channel PC's.
 IBMINT13.I13 supports non-Micro Channel SCSI adapters.
 OS2CDROM.DMD supports CD-ROM drives.
 FD16-700.ADD support driver for Future Domain 16xx SCSI.
 FD8XX.ADD supports Future Domain FD8XX devices.
 AHA154X.ADD supports SCSI on Adaptec 1542C controllers.
 AHA174X.ADD supports SCSI on Adaptec 1742 controllers.
 OS2ASPI.DMD Adaptec ASPI support.
 AIC7870.ADD supports SCSI on Adaptec 7870 controllers (e.g. 2940)
 ULTRA14.ADD supports Ultrastor SCSI controller.
 XDFLOPPY.FLT supports IBMs 1.8mb OS/2 installation disk format.
 AUTODRV2.SYS supports PCMCIA modems.
 ICMEMCDD.SYS & ICMEMMTD.SYS supports PCMCIA flash memory.
 PCM2ATA.ADD supports PCMCIA ATA devices.
 OPTICAL.DMD New with Warp4 Support for Optical devices like MO
 RESERVE.SYS New with Warp4, for not PnP aware adapters; see tip
 TIMER0.SYS New with Warp4, Harware timer for correct sound timings
 CHKDSK.SYS New with Fixpaks supports large disks
 ATAPI.FLT New with Fixpaks supports Removable Media like Zip100, LS120
 CMPXCHG8.SYS New with Fixpaks fixes the Pentium F00F bug
 MWDD32.sys 32-bit device driver support by Matthieu WILLM
            (Win32-OS/2 and many IFS's rely on it)

 <<=TIP=>>  Try adding the following switches to the
 BASEDEV=IBM1S506.ADD line: BASEDEV=IBM1S506.ADD /A:0 /U:0 /SMS,
 and use /V (/V=verbose) to see if the /SMS works.  This will
 improve performance on those IDE drives that support the SMS
 feature.  It will not work on all IDE drives, but it will not
 damage anything either.  See your Command Reference INF file
 for more information on these and other parameters for this
 driver. If you have problems with the busmuster feature in
 newer versions of IBM1S506.ADD (this occurs e.g. on some
 Thinkpads) disable the feature by adding !BM. In newer versions
 there is also the /W switch, it pauses the config.sys after
 displaying the verboses.

 <<=TIP=>>  If you wish to prevent users from using the
 floppy drives under OS/2 (to keep them from loading non-
 authorized programs or in a workstation situation), REM the
 BASEDEV=IBMxFLPY.ADD line (where x is 1 for ISA and EISA
 machines, or 2 for Microchannel).

 <<=NOTE=>>  In Warp, the install program may have placed both
 IBM1FLPY.ADD and IBM2FLPY.ADD BASEDEV drivers in your
 config.sys.  Remove IBM2FLPY.ADD if you don't have a Micro
 Channel PC.

 <<=WARP TIP=>>  With Warp, the default transmission protocal use
 by PRINTO1.SYS and PRINTO2.SYS is the polling transmission
 method.  The protocal used by previous versions of OS/2 was the
 interrupt transmission method.  In Warp, you can change back
 to the interrupt method by adding the /IRQ switch.

 <<=TIP=>>  From Paul Kurr:  "Since I'm running on a LAN at work
 here, I have no need for direct printer support of any kind since
 this is taken care of by my NOS (LAN Server).  So I have REM'd
 BASEVEV=PRINT01.SYS to save some RAM."

 <<=Tip=>> By Sam Detweiler: "for adapters that are not PnP and do not
 have a legacy detector, one can use the DOCUMENTED approach of adding
 a BASEDEV=RESERVE.SYS /p:2e8,8 to the config.sys and re-running hard-
 ware detection at the next boot. It causes the reserve.snp to pre-
 allocate the defined resources so that PnP adapters can't use them.

 <<=TIP=>> If Warp doesn't recognize the AIC7870 Driver add the
 parameter /A:n n=Number of Controller and /TAG:n n=number of
 PCI-Slot to AIC7870.ADD

 <<=TIP=>> By Paul F.Grobler: The tablet / enhanced mouse driver by
 M. Finney was broken by the GA code of Merlin but i found a work-around.
 The symptoms i got was an error free driver load (including vmouse.sys),
 a mouse cursor on the first graphic mode screen but the mouse pointer
 was static ie it would not move. All that was required was to put
 a "basedev=reserve.sys /IO:3f8,8 /IRQ:4" as the first line of my config.
 sys. You will note that the values correspond to normal com1 as this is
 were my tablet is connected. By modifying the values to /IO:2f8,8 and
 /IRQ:3 this should work for com2.

 <<=TIP=>> If you want to use SCSI Hardisks together with (E)IDE-Disks
 and to boot from SCSI first, make sure that the SCSI-Drivers are in
 front of the IDE-Drivers (normally IBM1S506.ADD).

 <<=TIP=>> After installation you can put an REM in front of the
 XDFLOPPY.FLT, as it's only needed for the installation disks and
 Fixpak disks.

 <<=TIP=>> If you have removable media drives (MO, IOMEGA, SYQUEST
 and others) look at http://rheooptik.fmf.uni-freiburg.de/www/faq/
 remmedia.htm for an detailed removable media FAQ.

 <<=TIP=>> If you are using RSJ CD Writer 2.59 or above you may
 add the parameter /ALL to BASEDEV=OS2ASPI.DMD.
 After booting your machine, the recorder will be usable as a standard
 CDROM drive, and you will nevertheless be able to attach the CD to our
 filesystem. But please ensure that you're not using the CDROM drive
 letter at the same time when the CDR is attached to RSJ's filesystem,
 otherwise this will result in errors.
 It seems that the latest version of the Adaptec 2940 driver (ver 2.2)
 does not work correctly with RSJ, but version 2.11 works fine.

 If you are using RSJ CD Writer 2.7 you can add unsupported drives
 BY RSJ Homepage: In order to add support for other drives than the
 models listed above, look into the file CDDRV.INF and copy an entry
 which resembles your drive according to the write speed and the RW
 capabilities. Change the SCSI-ID string to the one reported by your
 SCSI adapter and set the column "Compatible-ID" to the ID string of
 the drive used as template for the new entry. Finally, add the ID
 string to LOCKCDR.FLT in CONFIG.SYS as follows:
 "BASEDEV=LOCKCDR.FLT -i:"VENDOR MODEL". [...]«

 <<=TIP=>> If you are using an Adaptec SCSI Card you can also use
 BASEDEV=AHA152X.ADD /V /F:x to force the target SCSI ID x. The host
 adapter will assume that the target ID x is connected to SCSI Bus.

RESERVEDRIVELETTER=x

 New in Warp 4, Warp 3 with Fixpaks higher 35
 Note: Multiple RESERVEDRIVELETTER statements are allowed but only the
 last one is used.

 During the processing of CONFIG.SYS, OS/2 allocates drive letters for
 all BASEDEV= statements. In general, the only BASEDEV= statements that
 allocate drive letters are those for the Disk Device Driver, which
 will allocate 1 drive letter sequentially for each local disk
 partition. Three local disk partitions would allocate C:,D:,E:.

 After processing BASEDEV= statements, the system will honor the
 RESERVEDRIVELETTER statement(s). If the RESERVEDRIVELETTER statement
 conflicts with any drive letter already assigned to a local disk
 partition, an error message will be generated and that
 RESERVEDRIVELETTER statement will be ignored.

 The next processing occurs for DEVICE= statements.  DEVICE= statements
 for local block mode devices will assign drive letters, starting
 sequentially immediately after the highest drive letter specified in a
 RESERVEDRIVELETTER statement. Examples of local devices which use
 drive letters are CDROM, R/W OPTICAL, TAPE, Virtual Disks (VDISK).

SET BOOKSHELF=C:\GAMMA32;C:\OS2\BOOK

 This command points to the on-line documentation (INF files)
 provided with OS/2 or other OS/2 programs.  I have the
 GAMMATECH utilities installed on my system which contains
 on-line documentation.

 <<=TIP=>>  If you have an HPFS partition, copy all of your
 on-line documentation (INF files) to this partition.  Then
 change this parameter to reflect the new path.  You will
 notice a substantial improvement in search speed since HPFS
 is much faster than FAT.

SET EPMPATH=C:\OS2\APPS

 Replaced SET EPATH=C:\OS2\APPS in version 2.0.  According to
 one source in IBM, EPMPATH is used by the Enhanced Editor
 (EPM.EXE) to locate its files.

SET HELPNDX=FILE1.NDX+FILE2.NDX+...+FILEn.NDX

 The HELPNDX variable points to the index files which
 are used by the EPM editor and possibly by some
 other programming editors.  With EPM, you can mark
 a keyword in your text and press CTRL + H.  EPM
 then searches the index files for the marked word
 and if it is found, shows the online document for the
 keyword. The index files must be in a path defined
 by the BOOKSHELF or EPMPATH variable.

SET NOWIN32LOG=1
 Quoting the README of the w32os204 package:
 Although the output generated in win32os2.log very useful for
 debugging,it slows things down quite a bit.
 You can disable it by adding the following variable to your
 environment:
  SET NOWIN32LOG=ANY VALUE

DEVICE=D:\OS2\VASPIDD.SYS
DEVICE=D:\OS2\VASPI.SYS

  Adaptec ASPI device drivers for SCSI support.

DEVICE=C:\OS2\APPS\SASYNCDB.SYS
DEVICE=C:\OS2\APPS\SASYNCDA.SYS

 This device driver loads communications support for the PM
 Terminal applet.  The PM Terminal applet, and this
 device driver, were dropped in OS/2 Warp.

 <<=TIP=>>  If you don't use PM Terminal, REM this line to
 save a little memory.  In fact, if you are not using PM
 Terminal applet you may wish to consider deleting the files
 to save some disk space also.

DEVICE=C:\OS2\WIN32OS2\WIN32K.SYS

 Win32k - Win32-OS/2 driver, description in WIN32.TXT of the w32os2
 package.

DEVICE=X:\LPTOOL\LPTDD.SYS

 This driver is for the LPTools an parallel to parallel port
 solution like laplink.

 <<=NOTE=>> The FREE LPTool is developed by Jan van Wijk, and
 can be downloaded at his homepage http://www.fsys.demon.nl

PROTECTONLY=NO

 Allows you to choose between a shared DOS and OS/2 operating
 environment or just an OS/2 environment.  If you plan to run
 only OS/2 programs, then set PROTECTONLY=YES.  If you plan to
 run DOS programs (including Windows), then set PROTECTONLY=NO.

 <<=NOTE=>>  Jonathan de Boyne Pollard relayed the following:
 "Part of the difficulty of talking about OS/2 2.x, as opposed
 to OS/2 1.x, is that *all* processes run in *protected mode*.
 The 386 never runs in real mode in OS/2 2.x.

 "Virtual DOS Machines are run in v8086 mode, which is still
 *protected mode*, as the paging mechanism is still active.
 The major difference between v8086 and normal protected mode
 is that the segment base addresses in linear memory are
 fixed, instead of being determined by the entries for each
 selector in the LDT and GDT.

 "So PROTECTONLY in OS/2 2.x means *don't use v8086 protected
 mode*. For a while there we thought that it meant *don't use
 real mode* and so was useless to OS/2 2.x, but it seems after
 all that it retains its original OS/2 1.x semantics, if not
 its original mechanism."

SHELL=C:\OS2\MDOS\COMMAND.COM C:\OS2\MDOS /P

 This line identifies and loads the DOS command processor
 COMMAND.COM which you must have to make DOS sessions work.  The
 /p switch keeps the command processor in memory until shut down.

 <<=NOTE=>>  This is the line where you can also specify the size
 of the DOS environment variable.  The range is 160 through 32768.
 For example, to set a 1024 byte environment you would add the
 following to the end of the SHELL command line:  /E:1024

 <<=TIP=>>  You can also load and run other command processor's
 such as 4DOS.  To do so, just put 4DOS in your MDOS directory
 and change the SHELL line to read 4DOS.COM instead of
 COMMAND.COM.

FCBS=4,2

 File Control Blocks (FCBS) are an outmoded holdover from old
 versions of DOS.  The blocks are an internal holding area for
 data about concurrently open files.  In newer versions of DOS,
 these FCBS have been replaced by File Handles, but some DOS
 programs still use them and you need this statement for com-
 patibility.  The command tells an OS/2 VDM how many FCBS can
 be open at once, or, when DOS needs to open more FCBS than are
 available, how many currently open but not active FCBS may be
 closed to make room for new ones.

 The syntax is FCBS=a,b where a=the number of FCBS that DOS can
 have open at one time and b=the number of FCBS DOS cannot close
 to make room for new FCBS.  "a" can be as high as 255.  "b" can
 have a value of 0 to 254, but must be less than "a".  Unless
 you get some kind of error message when running a DOS program
 that tells you the program doesn't have enough FCBS, leave the
 default as set.

 <<=TIP=>>  You may wish to experiment with a smaller number.
 If you can get by with a smaller number, you will get back a
 little memory in each of your DOS sessions.  My suggestions is
 that you set it to 4,2.  If you make this change and then load
 a DOS program that says it can't open a file, increase the
 first value, reboot, and see if the error message goes away.
 You can also increase or change the value in the DOS programs
 Settings notebook.

RMSIZE=640

 This is a DOS command and sets the amount of memory available
 for use by each DOS session.  The maximum is 640k.  Since some
 DOS programs require 640k, its best to have RMSIZE set to 640.

 <<=TIP=>>  If you need maximum memory (more than 640k), see
 tip under DOS=LOW,NOUMB.

DEVICE=C:\OS2\MDOS\VEMM.SYS

 VEMM.SYS lets DOS programs use expanded memory unless you
 override it by changing a DOS programs SETTINGS.

 Three of its switches are:

   /S=n  Sets the limit of EMS memory in blocks of 1024k.
      Default is 2.

   /L=n  Size of conventional memory that can be remapped.
      Default is none.

   /F=nnnn  Memory frame address to be used to map EMS.
      Default is AUTO.

 <<=NOTE=>>  Settings you specify in a DOS session will
 override these switches.

 <<=NOTE=>>  The VEMM.SYS device must be listed in your
 config.sys file before the VXMS.SYS device.

DEVICE=C:\OS2\MDOS\VMOUSE.SYS

 Identifies and loads the mouse driver to let you use a mouse
 with DOS.  Mouse support for OS/2 is loaded below.

 <<=NOTE=>>  If you don't have this line (or you REM'd it), you
 will not have mouse support in your DOS sessions.

DOS=LOW,NOUMB

 This is a standard DOS command that lets you control how DOS
 uses memory.  The default is DOS=LOW,NOUMB and is considered
 by many to be the best setting for it conserves memory
 for OS/2.  DOS=HIGH (including ,UMB) reduces available memory
 for OS/2, but increases the available memory in EVERY DOS
 session.  Few DOS sessions need maximum memory.  Also remember
 that you can move DOS HIGH for a specific program by changing
 that programs Settings.  This is done in the programs Settings
 Notebook and is likely the better way to go.  Finally, keep in
 mind that in OS/2 many device drivers are not taking up room in
 your 640k DOS area.  So you generally have more memory in the
 typical OS/2 DOS session than in a standard DOS session.

 The following is the amount of memory my system reports in each
 DOS session with DOS=LOW,NOUMB.  The vast majority of all DOS
 programs will run just fine with this amount of memory.

   655360 bytes total memory
   655360 bytes available for DOS
   618208 largest executable program size    <---- About 604k.

 With DOS=HIGH, the amount of memory reported is:

   655360 bytes total memory
   655360 bytes available for DOS
   643632 largest executable program size    <---- About 629k.

 <<=TIP=>>  If you need the maximum available RAM in a DOS
 session and can get by on CGA or MONO, in the DOS Settings of
 your applications Settings Notebook, change VIDEO_MODE_RESTRICTION
 to CGA or MONO.  (Note that there are some reports from users
 that this procedure does not work on their hardware.)  A final
 note:  For this to work on some systems, you may need to change
 RMSIZE command to 639 (RMSIZE=639).  See description of this
 parameter under RMSIZE.  This is the result of a bug in OS/2.  I
 have not verified if this bug is still in Warp.  Any one care to
 verify if it is still around?

 The amount of memory reported after doing this on my machine is:

   752640 bytes total memory
   752640 bytes available for DOS
   740656 largest executable program size    <---- About 724k.

LOADHIGH C:\OS2\MDOS\TSR.EXE
LH C:\OS2\MDOS\TSR.EXE

 This command is for DOS sessions and loads TRS programs into
 upper memory blocks if they are available.  If upper memory
 blocks are not available, the TRS will be loaded into
 conventional memory.

DEVICE=C:\OS2\APM.SYS
DEVICE=C:\OS2\BOOT\APM.SYS <--- in WARP

 Device driver for ADVANCED POWER MANAGEMENT system used with
 laptop systems.  Not using a laptop?  Then REM or delete the
 statement.  If you are using a laptop, see the OS/2 README
 file for more details on its operation.

RUN=\OS2\BOOT\APMDAEMN.EXE

 New in Fixpaks, fixes some errors when using APM 1.2

RUN=C:\OS2\SMSTART.EXE

 This belongs to the error logging system, which no normal
 user will ever have use for.
 The output is only decipherable for REAL experts, so it is
 probably meant as a goodie for the IT people in large
 corporations, with their own software etc.

 <<=TIP=>> An REM in front of RUN=C:\OS2\SMSTART.EXE will stop
 the following processes: SMSTART.EXE, DMISL.EXE, ERLOGGER.EXE
 FFST.EXE. This is advised for all 'normal' users.

RUN=C:\MMOS2\MIDIDMON.EXE

 This is for MIDI

RUN=C:\MPTN\BIN\CNTRL.EXE

 TCP/IP Stack processing. CNTRL.EXE is a very important component
 of the stack. CNTRL.EXE provides threads for proper running of
 the stack. It provides a thread for each of the following: - IP
 input processing - TCP slow timeout processing - Debug thread for
 IP - ARP timeout processing - Ifndis debug thread - Watchdog thread
 for the adapter status - Loopback IP packets processing CNTRL.EXE
 is normally started from CONFIG.SYS with a RUN=statement. It should
 be the first program to begin executing when TCP/IP is started.
 CNTRL.EXE for Version 4 is different from that in the Version 2.0
 stack

DEVICE=C:\MPTN\PROTOCOL\IFNDIS.SYS

 Part of the TCP/IP Protocols

DEVICE=C:\MPTN\PROTOCOL\AFINET.SYS

 Part of the TCP/IP Protocols

CALL=C:\OS2\CMD.EXE /Q /C C:\MPTN\BIN\MPTSTART.CMD >NUL

 The file named MPTSTART.CMD contains Socket/MPTS
 configuration information for a workstation.  Socket/MPTS
 creates and updates a MPTSTART.CMD file, based on your
 configuration selections using the Socket/MPTS window
 interface or using the response files.

 MPTSTART.CMD is automatically started when the
 workstation is restarted by a call statement in the
 CONFIG.SYS file.

DEVICE=C:\OS2\MDOS\VXMS.SYS /UMB

 VXMS.SYS is a device driver that provides Extended Memory
 management to DOS sessions.  XMS allows DOS programs to access
 more than one MB of memory.

 There is a total of five switches available.

    /UMB  Upper memory block support in DOS sessions.

    /NOUMB  No upper memory block support.

    /XXMLIMIT=m,n  Indicates the total system wide memory limit.

    /HMAMIN=m  Sets the minimum request size for high memory,
               from 1k to 63k.

    /NUMHANDLES=m  Sets the number of handles in each DOS session,
                   from 1 to 128.

 <<=NOTE=>>  The VXMS.SYS device must be listed in your
 config.sys file after the VEMM.SYS device.

DEVICE=C:\OS2\MDOS\VDPX.SYS

 Driver required when using VDPMI in the config.sys line
 below.  One authority said that this driver "provides V86 to
 Protected Mode translation for DPMI memory".  Well that's
 enough to lose me.

DEVICE=C:\OS2\MDOS\VDPMI.SYS

 Provides "virtual" DPMI (DOS Protect Mode Interface) memory
 for DOS and Window sessions.  I don't know much about this,
 but I've been told not to remove it.

DEVICE=C:\OS2\MDOS\VWIN.SYS

 Assists in the process of providing seamless Windows support.

DEVICE=C:\OS2\EXTDSKDD.SYS

 EXTDSKDD.SYS supports external disk drives.  There are five
 switches available.  See your online Command Reference for
 complete details on these switches.

DEVICE=C:\OS2\PCMCIA.SYS
DEVICE=C:\OS2\MDOS\VPCMCIA.SYS

 These two drivers were new beginning with version 2.1.  They
 provide support for computers that have PC Memory Card
 International Association (PCMCIA) adapters.

 <<=TIP=>> If you don't have any PCMCIA devices, then you
 should REM these drivers to save a little RAM.

 <<=NOTE=>>  If you are using PCMCIA adapters and you find that
 your communications ports (COM1 - COM4) are not working
 properly, place these two device drivers after the COM.SYS and
 VCOM.SYS statements.

DEVICE=C:\OS2\MDOS\VCDROM.SYS

 This is a CD-ROM device driver that provides support in DOS
 sessions.

 <<=TIP=>> If you don't have a CD-ROM installed, then you should
 REM this line to save a little RAM.

IFS=C:\OS2\CDFS.IFS /C:4
IFS=C:\OS2\BOOT\CDFS.IFS /C:4     <---- In Warp

 This OS/2 command is needed if you have a CD-ROM.  It installs
 CDFS.INF which is the "Installable File System" for CD-ROMs.
 Your CD-ROM is not going to run without it.

 <<=TIP=>> You can add cache to your CD-ROM IFS by adding the
 /C:n switch.  The variable "n" is a number which represents
 units of 64kb of memory.  For example, /C:4 would set up a
 256kb cache (4 x 64kb = 256kb).

 Other switches include the following:

 /P: Indicates the debug output port. The values can be 1 (COM1)
     or 2 (COM2).

 /K  Indicates the supplemental volume descriptor with KANJI.

 /M:n  Where n indicates the maximum number of file sectors to
       read at a time.  The default is 8.

 /Q  Suppresses initialization messages.

 /w  enables Joliet support, new in Fixpaks

DEVICE=C:\OS2\OS2CDROM.DMD /Q
DEVICE=C:\OS2\BOOT\OS2CDROM.DMD /Q   <---- In Warp

 OS/2 driver used on many, but not all CD-ROM's.

DEVICE=C:\OS2\MDOS\VW32S.SYS

 WIN32 program support driver.

DEVINFO=SCR,VGA,C:\OS2\VIOTBL.DCP
DEVINFO=SCR,VGA,C:\OS2\BOOT\VIOTBL.DCP

 This command prepares your monitor to display information based
 upon the CODEPAGE specification.  VIOTBL.DCP is the file that
 contains the video fonts for displaying characters for each of
 the CODEPAGES supported by OS/2.  See the CODEPAGE command line
 below.

DEVICE=C:\OS2\MDOS\VVGA.SYS

 Your config.sys file will contain various device drivers for
 various devices based upon your systems hardware configuration.
 This device driver for supporting VGA video cards in DOS sessions.

SET VIDEO_DEVICES=VIO_SVGA
SET VIO_SVGA=DEVICE(BVHVGA, BVHSVGA)
DEVICE=C:\OS2\MDOS\VSVGA.SYS

 Your config.sys file will contain various device drivers for
 various devices based upon your systems hardware configuration.
 These device driver are for a SVGA video card.

SET VIDEO_DEVICES=VIO_VGA
SET VIO_VGA=DEVICE(BVHVGA)
DEVICE=C:\OS2\MDOS\VVGA.SYS

 Your config.sys file will contain various device drivers for
 various devices based upon your systems hardware configuration.
 These device driver are for a VGA video card.

SET VIDEO_DEVICES=VIO_MGA
SET VIO_MGA=DEVICE(BVHVGA,BMGAX64)
DEVICE=C:\MGA\OS2\KMGAX64.SYS

 These are the device driver for a Matrox video card


DEVICE=C:\OS2\POINTDD.SYS
DEVICE=C:\OS2\BOOT\POINTDD.SYS    <---- In Warp

 Provides mouse-pointer draw support.  Text modes 0, 1, 2, 3, and
 7 and graphic modes D, E, F, and 10 are supported.  For graphic
 modes D, E, F, and 10, the correct graphic device driver must
 also be installed.

 <<=WARNING=>> In order for MOUSE.SYS to work effectively, this
 driver must be loaded by OS/2 before MOUSE.SYS.  Do not remove
 it from your config.sys file.

DEVICE=C:\OS2\MOUSE.SYS SERIAL=COM1 QSIZE=10
DEVICE=C:\OS2\BOOT\MOUSE.SYS SERIAL=COM1 QSIZE=10  <-- In Warp

 Lets you use a mouse or track ball.  This line also identifies
 the type of mouse you have and which COM port it is on.  QSIZE
 is a number from 1 to 100 which indicates how many mouse
 actions are to be saved when you execute mouse actions
 faster than your system can handle them.  There is also a
 RELAXED parameter which you would place after QSIZE.  It can
 be used with any mouse when the pointer is jumping randomly
 about the screen.  IBM does not suggest you use this parameter
 unless you are experiencing this problem.

 <<=NOTE=>> The MOUSE.SYS statement must come before COM.SYS, but
 after POINTDD.SYS, because COM.SYS will take over any unused COM
 port.  If COM.SYS takes over the COM ports before MOUSE.SYS is
 loaded, MOUSE.SYS will not have any COM ports available, thus no
 mouse support.

DEVICE=C:\OS2\RODENT\RODENT.SYS COM=1 BUTTONS=3

 Device driver for the shareware mouse driver call Rodent.

DEVICE=C:\OS2\COM.SYS
DEVICE=C:\OS2\BOOT\COM.SYS        <---- In Warp

 Lets you use the communications ports COM1 and COM2.  If you
 want to use COM3 or COM4 or change the IRQ of any COM port,
 see <<=TIP=>> below.  This line MUST appear after any driver
 that uses a communications port.  Use COM02.SYS for IBM PS/2
 model 90 and 95.

 <<=TIP=>> There are two very good replacement drivers for
 COM.SYS\VCOM.SYS called SIO.SYS\VSIO.SYS.  It can be obtained
 on most OS/2 BBSs.  If you utilize communications software on a
 regular basis at high speeds (e.g. 14,400), I recommend you
 consider SIO.SYS.  Replace VCOM.SYS with VSIO.SYS which
 comes with SIO.SYS.  SIO.SYS and VSIO.SYS are Shareware, not
 Freeware.  Register them if you use them!

 <<=TIP=>> To add support for COM3 and COM4 at location 3E8 with
 IRQ 4 and 2E8 with IRQ 3 respectively, add (3,3E8,4) (4,2E8,3)
 to the DEVICE line, e.g. DEVICE=C:\OS2\COM.SYS (3,3E8,4)
 (4,2E8,3).  You can also use this method to change a COM ports
 assigned IRQ.

DEVICE=C:\OS2\COM02.SYS
DEVICE=C:\OS2\BOOT\COM02.SYS        <---- In Warp

 For IBM PS/2 model 90 & 95 only.

 Lets you use the communications ports COM1 and COM2.  If you
 want to use COM3 or COM4 or change the IRQ of any COM port,
 see <<=TIP=>> below.  This line MUST appear after any driver
 that uses a communications port.

 <<=TIP=>> To add support for COM3 and COM4 at location 3E8 with
 IRQ 4 and 2E8 with IRQ 3 respectively, add (3,3E8,4) (4,2E8,3)
 to the DEVICE line, e.g. DEVICE=C:\OS2\COM02.SYS (3,3E8,4)
 (4,2E8,3).  You can also use this method to change a COM ports
 assigned IRQ.

DEVICE=C:\OS2\MDOS\VCOM.SYS

 Lets you use the communications ports for DOS and Windows
 sessions.  Must appear after the COM.SYS driver.

 <<=NOTE=>> If you are using COM3 and/or COM4, add the
 appropriate parameters to the COM.SYS line above only.  It is
 not necessary to add any parameters to this line.  VCOM.SYS
 inherits its parameters from the COM.SYS line.

 <<=TIP=>> See TIP under DEVICE=C:\OS2\COM.SYS regarding
 SIO.SYS.

DEVICE=C:\SIO\SIO.SYS

 Excellent replacement driver for COM.SYS.  If you utilize
 communications software on a regular basis at high speeds
 (e.g. 14,400), then the SIO drivers are the way to go.
 SIO.SYS must reside in the config.sys after MOUSE.SYS !
 Be sure you have REM'd out COM.SYS when using.  SIO.SYS and
 VSIO.SYS are Shareware, not Freeware. See also VSIO.SYS.

DEVICE=C:\SIO\VSIO.SYS

 Excellent replacement driver for VCOM.SYS.  If you utilize
 communications software on a regular basis at high speeds
 (e.g. 14,400), then the SIO drivers are the way to go.
 Be sure you have REM'd out VCOM.SYS when using. SIO.SYS and
 VSIO.SYS are Shareware, not Freeware. See also SIO.SYS.

MODE

 MODE is a multipurpose command that allows you to control
 printer ports, serial ports, modems, video monitors and disks.
 For example, if you want to "lock" in the baud rate on COM2,
 add the following MODE command to your config.sys file:

 MODE COM2 baud  (where baud is the rate you want to lock)

DEVICE=C:\MMOS2\MVPRODD.SYS /I11 /D3 /S:1,220,1,5 /N:PAS161$
DEVICE=C:\MMOS2\AUDIOVDD.SYS PAS161$

 These two drivers are for MediaVision's ProAudio Spectrum
 sound card.  The first driver is set for IRQ 11, DMA 3 with
 Sound Blaster support on IRQ 5 and DMA 1.

 <<=Warp TIP=>>  MediaVison's technical support indicates that
 the only correct settings for the PAS 16 in Warp is IRQ 11
 and DMA 3.  If you are experiencing static or white noise
 during bootup, MediaVison indicates that this is caused by
 using an IRQ other than 11 and DMA 3.  They also indicate that
 the two device driver lines must be the last lines in your
 config.sys file.  Note that this information didn't solve the
 static problem for all users I've talked with, but it did for
 some.  Others have indicated that adding the /T:1 switch solved
 their "white noise" problem.

 My experience has been that any change to the MVPRODD.SYS
 parameters will solve this problem, until you have to reset
 your system without a proper shut down.  Then the "white
 noise" returns, so I add or subtract the /T:1 parameter.

 There are new drivers in the Warp FullPak which solved the
 "white noise" problem for me.

 <<=Warp NOTE=>>  I've heard that there may be a bug in Warp
 which causes problems in WIN-OS2 "seamless" mode.  A solutions
 is contained in SNDWOR.ZIP which can be downloaded from many
 OS/2 BBSs.

DEVICE=C:\MMOS2\ES1868DD.SYS /B:220 /D:1 /F:3 /I:5 /C:4 /M:300
       ,7 /N:ES18681$
DEVICE=C:\MMOS2\VAUDDRV.SYS ES18681$

 These are the sounddrivers for the ESS1868pnp (many soundcards)

DEVICE=C:\MMOS2\SB16D2.SYS 1 1 5 5 220 4 330 /N:SBAUD1$ /Q
DEVICE=C:\MMOS2\AUDIOVDD.SYS SBAUD1$

 These two drivers are for Sound Blaster 16 sound card.
 Regarding the SB16D2.SYS driver, Doug Boulter comments that:

 - the first number is the device number, in this case 1;
 - the second number is the 8-bit DMA channel, also 1;
 - the third number is the 16-bit DMA channel, in this case 5;
 - the fourth number is the interrupt, IRQ 5;
 - the fifth number is the base I/O address, 220H;
 - the sixth number is the buffer size; and
 - the seventh number is the MIDI base I/O address, 330H.

DEVICE=C:\MMOS2\SBAWED2.SYS /C:1 /D:1 /H:5 /I:5 /A:220 /M:330 /N:SBAUD1$
       /Q /P /G

 This driver is for Sound Blaster AWE32 sound card.

 <<=TIP=>> According to OS/2-Inside the statement can be shortened to:
 SBAWED2.SYS /N:SBAUD1$


DEVICE=C:\MMOS2\JAZZDD.SYS /I:5 /D:1 /E:5 /T:330 /Q:10 /P:220 /N:JAZZ1$

 Support driver of Creative Labs Jazz16 card.

DEVICE=C:\OS2\MDOS\ANSI.SYS

 This is the traditional DOS command most are familiar with.
 It only affects DOS sessions.  This line is not added to your
 config.sys file by default.  If you want it, you need to add it.

 OS/2 sessions have ANSI support by default.  If you are unsure
 if ANSI is on or off in an OS/2 session, go to an OS/2 command
 prompt and type ANSI.  You will get a message like:  "ANSI
 extended screen and keyboard control is on."  For an OS/2
 session, turn ANSI off or on by typing ANSI OFF or ANSI ON at
 an OS/2 command prompt.

 There is two switches:

    /X Redefines keys with extended dey values as distinct keys.
    /K Disables extended keyboard capabilities.  You would use
       this switch if an application does not support extended
       keyboard.

SET ETC=C:\TCPI\ETC
SET TMP=C:\TCPIP\TMP
DEVICE=C:\TCPIP\BIN\INET.SYS
DEVICE=C:\TCPIP\BIN\IFNDISNL.SYS
DEVICE=C:\TCPIP\BIN\VDOSTCP.VDD
DEVICE=C:\TCPIP\BIN\VDOSTCP.SYS
RUN=C:\TCPIP\BIN\CNTRL.EXE
RUN=C:\TCPIP\BIN\VDOSCTL.EXE

 Provides TCP/IP support for Warp's InterNet tools provided in the
 Bonus Pack.

 <<=TIP=>> If you don't need TCP/IP support in DOS sesions, and you
 don't if you are using the Bonus Pack tools, REM the following
 lines:

   DEVICE=C:\TCPIP\BIN\VDOSTCP.VDD
   DEVICE=C:\TCPIP\BIN\VDOSTCP.SYS
   RUN=C:\TCPIP\BIN\VDOSCTL.EXE

 Remember that Windows is a DOS based system.

DEVICE=C:\OS2\TOUCH.SYS

 (From OS/2s online documentation)

 Implements support for touch devices.  For a touch device to be
 effectively used, the POINTDD.SYS device driver and appropriate
 mouse device-driver support must be loaded. In addition, these
 statements must be included in the CONFIG.SYS file in the
 following order:

 o  A device-dependent statement that gives the name of the
    file containing the information for the touch device you use.

 o  A device-independent statement that identifies the touch
    device to TOUCH.SYS

 If during installation, OS/2 detects a touch device installed on
 your system, the Install program automatically loads the required
 device-driver support necessary to enable the touch device.  The
 touch device shares the auxiliary device (mouse) port on the
 system with the mouse by allowing the mouse to connect to the
 touch device, which is then connected to the system.

 The Install program automatically adds the following statements
 to the CONFIG.SYS file:

  DEVICE=C:\OS2\PDITOU0x.SYS CODE=C:\OS2TOUCO21.BIN INIT=C:TOUCH.INI
  DEVICE=C:\OS2\TOUCH.SYS TYPE=PDITOU$
  RUN=C:\OS2\CALIBRATE.EXE-C C:\OS2CALIBRAT.DAT
  DEVICE=C:\OS2\MOUSE.SYS TYPE=PDIMOU$

 "x" is 1 or 2 depending on the bus architecture of your system.
 TOUCO21D.BIN is the touch-device microcode binary file and
 TOUCH.INI is a text file containing default parameter settings.

 The RUN=CALIBRAT.EXE statement is to activate the Calibration
 program.  This program performs the dual actions of downloading
 calibration-constant data to the touch device each time the
 system is started, and enabling recalibration of the touch
 device at initial setup, and when the device is moved to a new
 location.

 To recalibrate the touch device, enter the following at an OS/2
 command prompt:

  x:           (where "x" is your OS/2 boot drive.)
  CD \OS2
  CALIBRAT -U

RUN=C:\OS2\CALIBRATE.EXE-C C:\OS2CALIBRAT.DAT
DEVICE=C:\OS2\PDITOU01.SYS
DEVICE=C:\OS2\PDITOU02.SYS

 See DEVICE=C:\OS2\TOUCH.SYS

DEVICE=C:\OS2\LOG.SYS

 This optional device driver installs OS/2s error log file.  If
 you want a log of errors that occur on your system, then add
 this and the next line to your config.sys file.  If you are
 interested in such things, you may wish to play with it, but
 be forewarned, the error log information is cryptic and
 incomplete.  See note below.  To learn what these codes mean,
 you need to have IBMs Systems Network Architecture Formats
 (GA27-3136-12) or, for a reasonable overview, get OS/2 2.1
 Unleashed, 1993, SAMS Publishing.

 The switch /E:nn sets the size of the error log buffer.  The
 range is from 4kb to 64kb with 8kb as the default.

 You will get a short and quick message during boot up
 indicating that Logging has been installed and what the buffer
 size is.

 <<=NOTE=>> LOG.SYS has its limitations.  It will not log an
 application error unless the application has been written to make
 use of LOG.SYS.  Some routine system errors will not log either
 because OS/2 opens an error message box on screen to report
 these.

RUN=C:\OS2\SYSTEM\LOGDAEM.EXE /E:C:\OS2\LOGFILE.DAT /W:16

 This RUN command starts the logging process and must appear
 AFTER you have installed the LOG.SYS driver noted in the
 config.sys line above.  The two switches are:

  /E:path\filename  This is the path and file name of the
     test file where the errors will be logged.  You can place
     it anywhere you want and call it anything you wish.
     NOTE:  Like the OS/2 INI files, this file is "locked" and
     you will not be able to access it with your standard text
     editor or the OS/2 System Editor.  You will get a
     "violation error".  The Enhanced Editor will open the file.

  /W:nn  This is the size of the file named with the /E
     switch.  The default size is 64k, but with this switch
     you can set the value from 4k to 64k.  I've set the file
     size at 16k in the example line above.

 <<=NOTE=>> Use SYSLOG.EXE from an OS/2 command line prompt to
 view your log file.

CODEPAGE=437,850

 Lets you use the alphabet of various countries and languages.
 The syntax is CODEPAGE=ppp,sss, where ppp is the number of the
 primary national alphabet to be used and sss is a secondary
 alphabet number.  From an OS/2 command line, you can use the
 CHCP command to switch between these two code pages.  This can
 be useful in order to type, display or print data in a
 different language from the version installed.  CHCP can be
 used either without a parameter to query the current code
 page, or with one parameter in order to switch between primary
 and secondary code pages.  CHCP cannot be used to change to a
 code page not defined in the CODEPAGE= config.sys line.

 437=US English alphabet and 850=multinational alphabet.  The
 multinational alphabet contains most of the accented letters
 used in various European languages.  Several other alphabets
 that can be supported by your version of OS/2.  See Table 6.0.

 <<=WARNING=>> Japan, Korean and Chinese require a special
 version of OS/2 and special hardware.

 <<=WARNING=>> The choice of code page is made at installation
 time and should only be changed by using Selective Install.

 <<=NOTE=>> If there is not a CODEPAGE statement in your
 config.sys, your keyboard will use an alphabet based on
 the COUNTRY statement found earlier in your config.sys,
 but your screen and printer will use their built in defaults.

 <<=TIP=>> Holger Granholm of Helsinki, Finland provided the
 following excellent commentary on CODEPAGE=437,850.

 "I would like to point out that the 437=US English alphabet also
 contains most of the accented letters used in various European
 languages as also shown by their secondary code page listing.

 "Code page 850 is missing a lot of the mathematical and
 electronics symbols and quite many of the graphic characters
 contained in the extended (128 - 256) ASCII character set.

 "Ever since I found out (in 1986) that I had to set my Epson
 printer to the US character set to be able to print the accented
 characters I have only used code page 437 on my computers.

 "The newer DOS versions force on you NLSFUNC, DISPLAY.SYS, CHCP
 and what not as soon as they learn that you use anything else
 than english. All these can be deleted to save memory. Also OS/2
 puts code page 850 ahead of 437 when you choose another country
 or keyboard than US/English.

 "One of the first things I did to the OS/2 CONFIG.SYS file was
 to change those around."

 ================== Table 6.0 =====================

 <<=NOTE=>> The Table is according to Warp 4 your system may vary

   COUNTRY                  PRIMARY      SECONDARY   ALTERNATIVE
                            CODE PAGE    CODE PAGE   CODE PAGE
   Albania                  850          437
   Austria                  850          437         1004
   Arabic-speaking          864          850         437
   Asia (English)           437          850
   Australia (English)      850          437         1004
   Baltic Countries         921
   Belgium                  850          437         1004
   Bosnia                   852          850
   Brazil                   850          437         1004
   Bulgaria                 915          850         855
   Canada (French)          850          863         1004
   Czech                    852          850
   Croatia                  852          850
   Denmark                  850          865         1004
   Estland                  922          850
   Finland                  850          437         1004
   France                   850          437         1004
   Germany                  850          437         1004
   Great Britain            850          437         1004
   Greek                    869          850         812
   Hebrew-speaking          862,850      437
   Hungary                  852          850         1004
   Iceland                  850          861         1004
   Ireland                  850          437         1004
   Italy                    850          437         1004
   Israel                   862          850         437
   Japan                    943          850         942
   Korea                    949          850         944
   Kroatia                  852          850
   Kyrillic                 855
   Latin America            850          437         1004
   Latin 1 Multlingual      850
   Latin 2 Eastern Eurpe    852
   Lettland                 921          850
   Mazedonia                855          850         915
   Netherlands              850          437         1004
   New Sealand              850          437         1004
   Nordic Lands             865
   Norway                   850          865         1004
   Peoples Republic of      1381         850         946
     China
   Poland                   852          850
   Portugal                 850          860         1004
   Rumania                  852          850         1004
   Russia                   866          850         915
   Serbia/Montenegro        855          850         915
   Slovak                   852          850
   Slovenia                 852          850
   Spain                    850          437         1004
   South Africa             850          437         1004
   Sweden                   850          437         1004
   Switzerland (French)     850          437         1004
   Switzerland (German)     850          437         1004
   Taiwan                   950          850         948
   Thailand                 874          850
   Turkey                   857          850         1004
   United Kingdom           850          437
   United States            437          850
   Windows Latin 1          1004

 <<=NOTE=>> Arabian, Greek, Hebrew, Thai and DBCS Codepages are only
 fully supported in OS/2-Versions developed for those countries.

 <<=TIP=>> In Warp 4 are many new Codepages, Codepage 1004 is according
 to the WINDOWS ANSI Standard, this is important for an correct
 interpretation of german 'umlauts' and to convert dokuments between
 Windows and OS/2

SET LANG=en_US

 Sets up the language and the country for applications
 that are using Unicode character sets.
 Here is a list of available settings:

 Albania (sq_AL)
 Arabic-speaking (ar_AA)
 Australia (en_AU)
 Austria (de_AT)
 Belgium dutch (nl_BE)
 Belgium French (fr_BE)
 Bosnia (sh_BA)
 Brazil (pt_BR)
 Bulgaria (bg_BG)
 Canada english (en_CA)
 Canada french (fr_CA)
 China (zh_CN)
 Croatia (hr_HR)
 Czechoslovakia (cs_CZ)
 Denmark (da_DK)
 Finland (fi_FI)
 France (fr_FR)
 Germany (de_DE)
 Great Britain (en_GB)
 Greece (el_GR)
 Hungary (hu_HU)
 Iceland (is_IS)
 Ireland (en_IE)
 Israel (iw_IL)
 Italy (it_IT)
 Japan (ja_JP)
 Korea (ko_KR)
 Latin America (es_LA)
 Netherlands (nl_NL)
 New Zealand (en_NZ)
 Norway (no_NO)
 Poland (pl_PL)
 Portugal (pt_PT)
 Romania (ro_RO)
 Russia (ru_RU)
 Slovak (sk_SK)
 Slovenia (sl_SL)
 South Africa (en_ZA)
 Spain (es_ES)
 Sweden (sv_SE)
 Switzerland german (de_CH)
 Switzerland french (fr_CH)
 Switzerland italian (it_CH)
 Taiwan (zh_TW)
 Thailand (th_TH)
 Turkey (tr_TR)
 United States (en_US)

DEVINFO=KBD,US,C:\OS2\KEYBOARD.DCP

 Tells the keyboard which international character set to use and
 where to find the file KEYBOARD.DCP which translates keystrokes.
 The syntax is DEVINFO=KBD,cc,DRIVE,PATH,FILENAME. The parameter
 cc equals the character set to be used, e.g. US = United States.
 See Table 7.0 for character set codes.

 =============== Table 7.0 ================

   LANGUAGE                   COUNTRY CODE
   Arabic                     AR
   Belgian                    BE
   Canadian French            CF
   Czech/Czech                CS243
   Czech/Slovak               CS245
   Danish                     DK
   Dutch                      NL
   Finnish                    SU
   French                     FR
   German                     GR
   Hebrew                     HE
   Hungarian                  HU
   Icelandic                  IS
   Italian                    IT
   Latin American             LA
   Norwegian                  NO
   Polish                     PL
   Portuguese                 PO
   Spanish                    SP
   Swedish                    SV
   Swiss (French)             SF
   Swiss (German)             SG
   Turkish                    TR
   United Kingdom             UK
   United States              US
   Yugoslavian                YU
 ==========================================

SET ZOCDEVICE=COM4

 Command used by older versions of ZOC,
 the excellent OS/2 communications Shareware program from Germany.

SET SPEALOGO=OFF

 Use this if you have an Spea Graphics-Card to disable the Logo

SET MGA=C:\MGA\OS2

 Sets the default installation directory for Matrox Video Cards

SET IBMAV=C:\IBMAV

 Sets the default path for IBMAV

SET TZ=MEZ-1 MSZ,3,-1,0,3600,10,-1,0,3600,3600

 Sets the Timezone correctly for Germany with daylight savings

 <<=TIP=>> As the correct setting of the TZ Parameters is somewhat
 delicate use the excellent FREE-tool TZCALC by Norbert Dey
 (at the moment tzcalc03.zip)

DEVICE=D:\BACKMAST\FTDVR.SYS
DEVICE=D:\BACKMAST\TC15DVR.SYS
DEVICE=D:\BACKMAST\PTDVR.SYS

 Drivers of Backmaster tape backup system.

DEVICE=C:\OS2\APPS\SYSIOS2.SYS  <<--- new with Warp

 This device driver is required by the System Information Tools
 provided in the "BonusPak" that comes with OS/2 Warp. If you plan
 on using these tools, do not delete this driver.

DEVICE=D:\FAX\FMD.SYS

 This driver is required by Faxworks lite 2.* in Warp 3 or the Pro
 Versions of Faxworks/PMFax

SET DSPPATH=C:\MMOS2\DSP;

 An environment variable used by various sound devices that support
 digital signal processors (DSPs).  This is a "path" statement.  It
 tells the device where to retrieve DSP modules.  If you don't have
 a sound device which supports DSP, like M-Audio adapter or the
 Sound Blaster 16 CSP, you can REM this line.

SET MMBASE=C:\MMOS2;

 An environment variable which indicates the path to OS/2s
 multimedia programs.

SET NCDEBUG=4000

 In both Lotus 123 and Excel, users can record and play back audio
 and video annotations for specific cells.  NCDEBUG is an
 environment variable required for this to work in Lotus 123.
 Excel does not need.  If you do not have a need for this support,
 or have Lotus 123, you may REM this line.

SET IBMWORKS_INI=C:\IBMWORKS    <<--- new with Warp

 IBM Works is an intergrated package of programs including a word
 processor, database and spreadsheet which is included with OS/2
 Warp's BonusPak.  This statement tells the system where the
 IBM Works' INI file is located.

 <<=TIP=>>  Many Warp users who have installed IBMWORKS from the
 BonusPak report that system performance is greatly enhanced by
 running IWDEREG.CMD program contained in the IBMWORKS folder.
 This program deregisters IBMWORKS and releases a large amount
 of RAM back to your system.  Yes, IBMWORKS will still work, but
 you may lose some functionality between applications.
 To do this in Warp 4, use the REXX script available at
 ftp://eepjm.newcastle.edu.au/freeware/IWDEREG.CMD

SET SPCH_MAINLANG=XX_XX

 Sets the desired language for voicetype if there are more
 languages installed

SET ULSPATH=C:\LANGUAGE;

 Sets the path for unicode language files, needed for Java

SET CLASSPATH=C:\NETSCAPE\JAVA11\JEMPCL10.ZIP;....\

 Sets the path for the Java Classes

SET JAVA_CONSOLE=1

 All Java Programs and Applets run in an console


SET JAVA_NLS_SBCS=1
 Specifies that Java should run in single-byte character set
 (SBCS) mode even in double-byte character set (DBCS) environments.


SET JAVA_NL_DBCS=1

 Java uses in double-byte environments only one byte


SET JAVA_NOPRINTDLG=1

 Specifies that Java should suppress display of the
 printer properties dialog box before printing.
 This allows jobs to print, without user intervention,
 using the default printer properties.


SET JAVA_AUDIO_RATE=n
 Sets the preferred playback sample rate for audio.
 A value of 8 for n sets the playback rate to 8000 samples
 per second. Use a value of 11 for 11025 samples per second.
 The Java runtime normally tries a sample rate of 8000 first,
 which matches the incoming data stream rate, and then 11025.

 <<=TIP=>> Some drivers, such as some ThinkPad 701C drivers
 dated prior to October 1995, appear to support a sample rate
 of 8000 but then fail; they can be made to work by setting a
 playback sample rate of 11025.


SET JAVA_AUDIO_VOLUME=v
 Adjusts the volume level for the audio output. v is the
 percentage of the maximum volume, from 0 to 100.
 The default is 75.


SET JAVA_COMPILER=<xyz>

 Specifies the name of the just-in-time (JIT) compiler to load.
 The default JIT is JAVAX.

 <<=TIP=>> To disable the JIT, specify the name of a non-existent
 DLL. ATTENTION, this will heavily decrease the speed of Java


SET JAVA_CONSOLE=1

 Specifies that Java programs started by JAVA and APPLET are run
 with a Java console.


SET JAVA_HOME=<dir>

 Specifies the path to the shared Java runtime directories.


SET JAVA_NOPRINTDLG=1
 Specifies that Java should suppress display of the printer
 properties dialog box before printing. This allows jobs to
 print, without user intervention, using the default printer
 properties.


SET JAVA_USER=<dir>

 Specifies the path to the directory for user-specific files
 such as the hotjava\property file.


SET JAVA_WEBLOGS=<dir>

 Specifies the path to the directory where weblog files for
 each started Java process are written.

DEVICE=C:\OS2\VDISK.SYS 512
DEVICE=C:\OS2\BOOT\VDISK.SYS 512  <<--- In Warp

 As in DOS, this driver installs a RAM disk.  In this example,
 the RAM disk is 512k with the sectors and directories parameters
 set at the default level (64-byte sectors and 64 directory
 entries).  With DOS, a RAM disk could significantly improve
 system performance, but because OS/2 handles your memory far
 more efficiently than DOS and has its own sophisticated caching
 routines, using a RAM disk is not recommended.

 <<=CAUTION=>> Because a RAM disk takes available memory away
 from OS/2, you may negatively impact system performance on
 systems with less than 12MB of RAM.  Unless you have lots of
 RAM or have a very specific need, don't install a RAM disk.

 <<=NOTE=>> If you do install VDISK.SYS and you also have
 EXTDSKDD.SYS installed, VDISK.SYS must be placed after
 EXTDSKDD.SYS in your config.sys file.  Check your on-line
 Command Reference for information on EXTDSKDD.SYS.

DEVICE=C:\OS2\MDOS\VNPX.SYS

 This device driver works _with_ your systems math coprocessor.
 If you do not have a math coprocessor, this driver will not load.
 Some have suggested that if you add it to your config.sys you
 will see an enhancement in your systems performance.  Not so.
 There is no reason for it to be added to your config.sys
 file.  IF YOU HAVE A MATH COPROCESSOR, OS/2 WILL LOAD THIS
 DRIVER AUTOMATICALLY.  If you add it to your config.sys file,
 a second copy of the driver will be loaded.  In doing so, many
 have reported that no DOS programs would run.  DO NOT ADD THIS
 STATEMENT TO YOUR CONFIG.SYS FILE.

SET OCRNOTES=C:\Faxworks\Calera

 SET OCRNOTES supports the optical character reader software from
 Calera.

-----------------------------------------------------------------
5.  NOVELL NETWARE NETWORK SUPPORT.

 Novell's NetWare is the most popular PC Network software around
 today.  We use it at work and I've used our config.sys file
 entries as the basis for this section of information.

 <<=NOTE=>> I'm not very knowledgeable about networks, so if
 someone would like to expand on this information and send it to
 me, I'd love to give you credit and include it here.

REM --- NetWare Requester statements BEGIN ---

DEVICE=C:\NETWARE\LSL.SYS

 Loads Link support Layer driver.  It is the lowest layer in
 the Novell Open Data Link Interface model and is required at
 all times for the requester to be active.

RUN=C:\NETWARE\DDAEMON.EXE

 A daemon is a background process that usually carries out
 administrative tasks for the system without you knowing it.
 This "daemon" is required for the requester to be active.

DEVICE=C:\NETWARE\TOKEN.SYS

 This line differs depending on the network board you have.

DEVICE=C:\NETWARE\ROUTE.SYS

 No information available.

DEVICE=C:\NETWARE\IPX.SYS

 Provides Novell IPX protocol support and is required for
 access to a NetWare server.

DEVICE=C:\NETWARE\SPX.SYS

 Provides Novell SPX protocol support.  It is my understanding
 that this command is required for some Novell printing
 utilities, but is optional in most cases.

RUN=C:\NETWARE\SPDAEMON.EXE

 Loads a daemon process that handles SPX packets.

REM DEVICE=C:\NETWARE\NMPIPE.SYS

 Loads the support for client-only Named Pipes support.

REM DEVICE=C:\NETWARE\NPSERVER.SYS

 Loads support for your workstation to function as a Named
 Pipes server.

REM RUN=C:\NETWARE\NPDAEMON.EXE NP_COMPUTERNAME

 This line is required for either the client or the server
 NetBIOS support to be active and is a daemon program that is
 part of the Named Pipes support.

DEVICE=C:\NETWARE\NWREQ.SYS

 This is the CORE REQUESTER MODULE.  This line must follow any
 lines that support IPX, SPX, or Named Pipes.

IFS=C:\NETWARE\NWIFS.IFS

 This installed the networks Installable File System.  This IFS
 enables OS/2 to see the network drives just the same as local
 drives.

RUN=C:\NETWARE\NWDAEMON.EXE

 Another daemon program, but I'm not sure for which process.

DEVICE=C:\NETWARE\NETBIOS.SYS

 Loads support for the NETBIOS protocol.

RUN=C:\NETWARE\NBDAEMON.EXE

 Loads the NETBIOS daemon process.

DEVICE=C:\NETWARE\VIPX.SYS

 Loads support for multiple virtual DOS machine support.  It is
 required both to have multiple DOS boxes on the network and to
 run the NetWare DOS based utilities.

DEVICE=C:\NETWARE\VSHELL.SYS

 Loads the network shell.  It is automatically used for all DOS
 and WIN-OS/2 sessions that require it.

REM --- NetWare Requester statements END ---
-----------------------------------------------------------------
5a.  OTHER ITEMS

DEVICE=C:\IBMCOM\PROTMAN.OS2 /I:C:\IBMCOM
RUN=C:\IBMCOM\PROTOCOL\NETBIND.EXE
DEVICE=C:\IBMCOM\MACS\IBMTOK.OS2

 These commands are added to your config.sys file when you install
 LAN Adapter and Protocol Support (LAPS).  LAPS may also add other
 commands if other protocols like NETBIOS and IEEE 802.2 are
 loaded.

DEVICE=C:\CMLIB\VHAPI.OS2

 Paul Kurr wrote the following.  "This provides for Virtual HLLAPI
 support within VDM's (not sure about VMB's).  This allows DOS
 programs that use the HLLAPI to access the HOST sessions running
 at the OS/2 level under comm mgr.  So you can actually watch your
 comm mgr sessions in one window and your DOS program in another
 while they interact."

DEVICE=C:\IBMLAN\NETPROG\VNETAPI.OS2

 Paul Kurr wrote:  "This sets up the virtual network support API
 within the VDM's (not VMB's).  This allows DOS programs running
 within a VDM to "see" that the network is loaded, and interact
 with it (get/set redirections and such).  If VDOLANAPI support
 is required in a VMB the device driver VNETAPI.SYS needs to be
 loaded within the VMB (this is found in \IBMLAN\NETPROG)."

RUN=C:\IBMLAN\NETPROG\VNRMINIT.EXE
SET NWDBPATH=C:\IBMLAN\NETPROG
SET DLSINI=C:\IBMLAN\NETPROG\NETGUI.INI
SET INIT_FILE_NAMES=netgui
SET INIT_FILE_RANGES=200
SET WPS_COMMUNICATION=YES
SET LOCPATH=C:\IBMLAN\XPG4\LOCALE
SET LANG=ENUS437
DEVICE=C:\IBMLAN\NETPROG\RDRHELP.200
IFS=C:\IBMLAN\NETPROG\NETWKSTA.200 /I:C:\IBMLAN /N
RUN=C:\IBMLAN\NETPROG\LSDAEMON.EXE

 Items with \IBMLAN provide support for LAN Server.  According to
 Paul Kurr, the SET statements are for LS 4 GUI support.

-----------------------------------------------------------------
END OF CONFIG.SYS FILE DESCRIPTION

-----------------------------------------------------------------
6.  OBSCURE CONFIG.SYS SETTINGS.

 What follows are some very obscure config.sys settings.  They
 are here only for informational purposes.  Unless you have a
 very specific need and know what you're doing, please don't
 experiment with these.

SET SHELLEXCEPTIONHANDLER=OFF

 The WpS has its own exception handling routines which allow it
 to recover from most errors, but when programming your own
 objects, you want to see all errors as they occur.  You can turn
 WpS "exception handling" off with this command.  Could be useful
 when debugging a Workplace Shell object.

SET AUTOREFRESHFOLDERS=NO

 with this environment setting the WPS doesn't automatically refresh
 folders (autorefresh happens to every folder which has been ever
 accessed and therefore slows the system). They are only refreshed after
 closing and opening an folder or by an manual update using 'view,
 refresh'.

 <<=TIP=>> Especially for Fileservers this Statement is very useful, also
 for slow systems.

SET OBJECTSNOOZETIME=45

 Useful when programming certain types of object DLLs.  The
 default setting for the snooze time is 90 seconds.  Unless you
 are programming your own Workplace Shell objects, you should
 not change the default setting.

SET SCROLLUP=1

 Enables slow scrolling of the WarpCenter, only in Warp4 Beta

SET SHAPIEXCEPTIONHANDLER=OFF

 This command disables the WpS API exception handler, and all
 WpS exceptions are handled by OS/2.

SET VIDEO_APERTURE=xxx

 This command allows you to set the address for video memory
 refresh buffers, where xxx is a hexadecimal number. E.g for
 PCI A00

SET MMBUF=49152

 This increases the size of the read buffer.  The default is 32768.
 It can be set even higher, but movies will take longer to load.

SET MMSTREAM=/H:256

 This increases the heap space for the stream manager to 256K, which
 allows more movies to be open at once and may improve performance.
 The default is 64K, and 256K is the maximum.

SET COPYFROMFLOPPY=1

 If OS/2 should install updated drivers during an installation from the
 Installation disks and not from CD this statement must reside in the
 config.sys on Installationdisk 1

SET CONNECT_DASD=OFF

 Disables the test for free space during the installation

SET CONNECT_PREREQ=OFF

 Disables the check of installed software during installation

SET CONNECT_SNIFF=OFF

 Disables the recognition of network-cards during installation

 Thes settings are only useful for installing problems with warp4
 and must be done in the config.sys on the installation diskettes

SET SCCANBENUKED=1
 Enables the deleting of the Warpcenter Icon

 <<=TIP=>> This REXX-Script reestablishes the Icon if it is deleted,

 /* Recreate Warpcenter */
 call RxFuncAdd 'SysLoadFuncs',,
     'RexxUtil', 'SysLoadFuncs'
     call SysLoadFuncs

 /*Code*/
 rc = SysCreateObject("SmartCenter", "WarpCenter", "<WP_OS2SYS>",
 "OBJECTID=<WP_WARPCENTER>","F")
 if rc = 0 then
 say "New WarpCenter Created."
 else say "Warpcenter creation failed! RC=" rc

 <<=TIP=>> You can also use the FREE tool 'ObjectReCreator'
 (orc.zip) by Kai Evers available at http://www1.stuttgart.
 netsurf.de/~kevers/ It can recreate all standard Desktop Objects
 who are lost or deleted

SET JAVA_CLOCK_RESOLUTION = 1

 Sets the Minimum of the timer resolution in JavaApps using
 currentTimeMillis to 1 Millisecond (the highest resolution).

 The best Java-Speed using currentTimeMillis can be achieved
 with JAVA_CLOCK_RESOLUTION = 32.
 This can be important for Java-Benchmark-Tests.

SUPPRESSPOPUPS=x

 SUPPRESSPOPUPS=0 will restore behavior to pre-FixPak 29 behavior.  That
 is, to disable logging and to have trap screens displayed unless
 specifically overridden by an application's use of the DosError API.

 SUPPRESSPOPUPS=x: will disable trap screen display for all processes and
 will log trap screens in x:\POPUPLOG.OS2, where x: is a drive or
 partition.

 If SUPPRESSPOPUPS is omitted then the behavior is as described above
 under "Automated Trap Screen Logging".
 <<=NOTE=>> The log file name cannot be overridden.

REIPL=ON  <---- new with Warp.

 This command automatically restarts the system when a system
 trap or internal processing error occurs.  Parameter is ON or
 OFF.  Default is OFF.

 <<=TIP=>>  This command along with the SUPPRESSPOPUPS command
 can be very useful to those running a BBS.  If a trap or internal
 processing error occurs while your BBS is unattended, having
 these two command in your config.sys will cause your system to
 log the error and then restart the system, so your BBS is back
 online.

TIMESLICE=128,256

 This command allows you to manually control the minimum and
 maximum amount of processor time any thread can receive at
 once.  The syntax is TIMESLICE=x,y where x is the minimum time
 slice (in milliseconds and must be at least 32) and where y is
 the maximum length (must be less than 65536).

 Jim Gilliland once posted: "The Timeslice parameter controls the
 minimum and maximum timeslice that OS/2 will allow an application
 to use.  If you make the timeslice longer, OS/2's dispatching
 overhead will be reduced, but the system's multitasking operation
 will be "choppier".  Increasing the length of the maximum
 timeslice (the second parameter) will allow OS/2 to gradually
 increase the length of the timeslice used by an application when
 it is not competing with any other apps for CPU time (that is,
 when it is the only app running or all others are blocked)."

 <<=TIP=>> OS/2 handles time slicing dynamically.  This means
 that the system is adjusting the time slice values based on
 the actual processes active on the system as the workload
 changes.  Therefore, it is best not to attempt to manually
 set TIMESLICE.  OS/2 can handle this process far better than
 most of us can.

TRACE=ON

 The system trace facility is used to record a sequence of
 system events, function calls, or data.  The record is usually
 produced for program debugging purposes.  After the trace data
 is recorded, the System Trace Formatter is used to retrieve it
 from the system trace buffer (see TRACEBUF below) and format
 the data to either your display, printer, or to a file.  Start
 tracking system problems by turning TRACE on which will
 establish a 4KB default buffer.  (You can increase this using
 the command TRACEBUF) to store tracing data.  You can also
 start TRACE from an OS/2 command prompt.

 <<=NOTE=>> You can turn TRACE=ON and then set TRACE=OFF for
 major or minor codes.  For example, TRACE=OFF 24,50,98.

TRACEBUF=x

 This command sets the size of the trace buffer.  If any valid
 TRACE statement is in your config.sys, the default size of
 the trace buffer will be 4KB.  You can modify this size with
 the TRACEBUF command.  Maximum size is 63KB.  "x" is a specific
 number from 1 to 63, representing a multiple of 1024 bytes.

TRAPLOG [x: | NOLOG] [POPUPS | NOPOPUPS]

 The TRAPLOG command allows dynamic control of trap information logging.

 where:
 ■  x: specifies that trap information is to be logged in
    x:\POPUPLOG.OS2, x: being any partition drive letter.
 ■  NOLOG disables logging of trap information.
 ■  POPUPS enables the trap information pop-up message (SYS3175).
 ■  NOPOPUPS disables the trap information pop-up message.


TRAPDUMP=xx,d

 Parameters are:  OFF,drive letter
                  ON,drive letter
                  R0,drive letter

 Indicates when a stand alone dump is to be taken and where the
 dump is to be placed.  The default value is OFF and the default
 drive is "A".

 If you are sending a memory dump to hard disk, you must first
 create a FAT partition labeled SADUMP and give it a size
 greater than the amount of physical memory in your system.
 The drive you specify in the TRAPDUMP statement must contain
 the SADUMP partition.  Any existing data in this partition
 will be overwritten.  The system will restart after the TRAPDUMP
 process has been completed.

 <<=NOTE=>> If REIPL=ON is specified in the config.sys file, the
 system will restart automatically and no dump will be taken when
 a system trap or internal processing error occurs.

 Luca Regoli, Societa' Italiana Autori Editori, provides the
 following information on this command.

 "This way whenever a trap occurs you don't get anything on the
 screen.  The PC beeps and [responds] as if you had depressed
 CTRL+ALT+NUMLOCK / NUMLOCK.

 "Not very useful though I don't know how to get traps infor-
 mation from the dump disk (and don't want to download all 20Mb
 dump of memory any time I get a trap)."

NEW TRAPDUMP

 The TRAPDUMP command allows the conditions under which a trap will
 initiate a System Dump to be set dynamically. Prior to Warp 3.0 FixPak
 29, the System Dump setting could only be manipulated from CONFIG.SYS by
 use of the TRAPDUMP statement.

 Use of this command should be made under the direction of service
 personnel.

 Warning: The initiation of a System Dump causes an immediate termination
 of the system without any shutdown. No file system shutdown is performed.
 The system behaves as if a fatal crash has occurred, thus under rare
 circumstances data can be lost.

 The command syntax is:
          TRAPDUMP [[ON] | [OFF] | [R0]] [x:] [/NOCHECK]


 where:

 ■  ON enables all application and system traps to initiate a System Dump.
 ■  OFF disables automatic dump initiation.
 ■  R0 enables only Ring 0 traps to initiate a System Dump.
 ■  x: specifies the Dump Partition.
 ■  NOCHECK overrides the system level check for WARP 4.0, since use of
    this command on a system level prior to FixPak 29 is equivalent to the
    SYSDUMP command.


SYSDUMP

 The SYSDUMP command forces a System Dump to be initiated, regardless of
 the TRAPDUMP settings. This command is provided for the use of service
 personnel to allow Dump Initiation to be automated through use of a
 command file.

 Warning: The initiation of a System Dump causes an immediate termination
 of the system without any shutdown. No file system shutdown is performed.
 The system behaves as if a fatal crash has occurred thus under rare
 circumstances data can be lost.

 The command syntax is:

 SYSDUMP [/NOPROMPT]

 where:

 ■  NOPROMPT allows the Dump to proceed without the prompt and response to
    message:

    "Do you want to force a system dump? (Y/N)"


DUMPPROCESS=x

 Activates the Dump Process.  Any application process that traps
 will cause a process dump.  The information will be written to
 a dump file named PDUMP.xxx where xxx is an index that is
 incremented each time a new process dump is created.  This dump
 file resides in the root directory of drive specified in "x".

PROTECT16

 Haven't found out about this one yet.  Comments?

AUTOFAIL=YES

 This command does not appear in your config.sys.  If not set to
 Yes, OS/2 default is No.  In the default setting, when an error
 occurs, OS/2 will only display a window informing you of the
 problem.  If you wish to see the actual error code information,
 set AUTOFAIL to Yes.

 <<=NOTE=>>  This command can't be run from an OS/2 prompt.

 <<=TIP=>>  Paul Kurr writes:  "I set this value to YES on my
 machine so that I'm not interrupted with those pesky drive not
 ready popups and such.  AUTOFAIL=YES takes the "first" option
 in those windows presented (usually return error code to program).

 "This can be seen most easily when running WIN-OS2 with a CDROM
 installed--either empty or with a music CD in the drive.  With
 AUTOFAIL=NO (default) OS/2 pop's up the window stating that my
 drive "E" is not ready.  With AUTOFAIL=YES, the first "selection"
 from that error is executed -- returning the failed drive status
 to WINOS2, which just keeps running fine."

VME=NO

 If you attempt to run WIN-OS2 and see the error message DOS 5
 Error, you may need to add this command.  Paradox V4.5 for DOS
 and Turbocadv3.2 for DOS under Warp 3 are known to need this
 command in some cases.  The code to support Virtual Mode
 Extensions on Pentium machines will occasionally causes problems
 with Warp.  This command generally solves the problem.

SET BEGINLIBPATH=C:\OS2
SET ENDLIBPATH=C:\OS2

 With Warp, IBM has introduced the ability to dynamically change
 LIBPATH using two new environment variables:  BEGINLIBPATH and
 ENDLIBPATH.  These commands are most useful in CMD or BATCH
 files, but can be used in your config.sys.  Any directories that
 appear in the BEGINLIBPATH variable are searched before
 directories in LIBPATH, and directories that appear in the
 ENDLIBPATH variable are searched after those in LIBPATH.


-----------------------------------------------------------------
7.  SAMPLE CONFIG.SYS FILES.

-------------------------------------------------------------------
 I deleted the old samples as nobody I know is working nowadays with
 4MB or 8MB, but its possible if you like slow systems :-)
 Also is the config on every system very different from others.
 In the times of large memory - 64MB and up - it is not necessary
 to save 3KB of Ram by optimizing the config.sys when every simple
 Office needs 32 MB or more (K.S.)
 Instead I've inserted here some useful tips to speed up your
 system by removing 'unwanted' or 'unneeded' and how to use other
 Installable File Systems (for Windows, Linux, Apple, TVFS) - the
 Zipstream.IFS is not mentioned here as great drives with lots of
 empty space are so cheap today that the use of an Disk-Compression
 is no more advised (if it was ever).

 The best way to optimize your system is
 1. to use only HPFS
 2. Use OS/2 without dos and windows sessions (so you get also
    rid of those nasty little algorithms called virus)
 3. Don't use voicetype if you don't need it, you can also make
    different boot options (with and without VT) see Chapter 8.
 4. Use small apps (like Papyrus) and not those Ram-Hogs like
    Staroffice
 5. Use native apps (not Java, Windows, Mirrorports like Word-
    perfect for OS/2)
 6. Delete the OpenDoc-Part by using 'selective-delete', as
    OpenDoc is deplorably death.

 Btw. when you compare the speed of windows and OS/2 on the same
 system, remember that windows can only boot from the first partition,
 the one which is on most drives the fastest !
 Using removable media together with OS/2 and newer Fixpaks slows
 bootup significantly. As an bargain (compared to windows, all
 versions) you get dynamically assigned drive letters, an feature
 that saves you from the drive-letter chaos in Windows whenever
 you change an partition, drive etc.
------------------------------------------------------------------
 If your only internet connection is via a modem, then you
 can comment out (or delete) the following lines from CONFIG.SYS
 in Warp 4
------------------------------------------------------------------
    REM DEVICE=C:\IBMCOM\LANMSGDD.OS2 /I:C:\IBMCOM /S
    REM DEVICE=C:\IBMCOM\PROTMAN.OS2 /I:C:\IBMCOM
    REM RUN=C:\OS2\SMSTART.EXE
    REM CALL=C:\IBMCOM\PROTOCOL\NETBIND.EXE
    REM RUN=C:\IBMCOM\LANMSGEX.EXE
    REM DEVICE=C:\MPTN\PROTOCOL\AFOS2.SYS
    REM DEVICE=C:\MPTN\PROTOCOL\IFNDIS.SYS
    REM CALL=C:\OS2\CMD.EXE /Q /C C:\MPTN\BIN\MPTSTART.CMD >NUL
    REM DEVICE=C:\IBMCOM\MACS\NULLNDIS.OS2
------------------------------------------------------------------
 If you don't run DOS/Windows TCP/IP programs, then you can remove
 the DOS TCP/IP support.  The relevant lines in CONFIG.SYS are:
------------------------------------------------------------------
   REM DEVICE=C:\tcpip\bin\vdostcp.vdd
   REM DEVICE=C:\tcpip\bin\vdostcp.sys
   REM RUN=C:\tcpip\bin\VDOSCTL.EXE
------------------------------------------------------------------
 If you don't use Voicetype remove the following
------------------------------------------------------------------
 Remove all statements in LIBPATH, SET PATH, SET DPATH and SET HELP
 pointing to Voicetype (normally they start with x:\vt)

 Then delete the following lines:
 SET SPCH_RUN=X:\VT\SPCH_RUN
 SET SPCH_RO=X:\VT\SPCH_RO
 SET SPCH_RW=X:\VT\SPCH_RW
 SET SPCH_BIN=X:\VT\SPCH_BIN
 SET SPCH_PATH=X:\VT\SPCH_RO\LANGS\%L\POOLS
 SET SPCH_TRN=X:\VT\SPCH_DBF

 <<=TIP=>> You can also make two different configurations and
 boot them alternately by pressing ALT-F1 see Chapter 8. or
 how to restore a damaged Config.sys file from a backup copy
-----------------------------------------------------------------
 Removing Artchron and other 'unwanted' autostarts
-----------------------------------------------------------------
 There is an clean way of removing the register program from your
 system. Navigate *through the Drives ICON* to /OS2/install/Installed
 Objects and double click on "Install Object - Inventory". Then
 check the box next to "art" and then click on "uninstall" and then
 select "art" in the next box that opens and then "uninstall"
 again...this will totally uninstall the "art" directory and all
 components relating to registration.
 Some applications (like Staroffice, Smartsuite, Amipro) install
 some 'reminders' or 'speeders' in the autostart-folder
 remove or delete them, they are normally not needed.
-----------------------------------------------------------------
OS/2 and other Operationsystems
-----------------------------------------------------------------
 OS/2 and Linux

 There  is an excellent FREE EXT.IFS by Matthieu Willm

 You can find the latest version of ext2-os2 at the ext2-os2 home page :

 http://www.geocities.com/SiliconValley/Bay/5313, or many other
 bbs and servers

 ext2-os2.ifs is a file system driver that allows OS/2 to
 seamlessly access Linux native partitions (ext2fs partitions)
 in both read and write modes. Once installed, Linux partitions
 appear as standard OS/2 drive letters, one per Linux partition.
 It is a port of the original Linux ext2fs kernel code.
 ext2-os2 can even be used without Linux, as it can format or
 check ext2 file systems directly from OS/2. This can be useful
 for people who need huge cache sizes, for large compilations for
 instance ; it can also be useful for people wanting long file
 names on removable media.

 <<=WARNING=>> Although it is possible to install OS/2 on an
 EXT2 Partition it is not recommended to do so, as extented
 attributes are not supported.
-----------------------------------------------------------------
 OS/2 and Windows NT

 OS/2 recognizes NTFS formatted drives falsly as HPFS

 Using the FREE EXT2FS necassary for Linux the NTFS partition
 can be hidden by inserting
 BASEDEV= EXT2FLT.FLT <options>
 to your config.sys file. The following command line options are allowed:

 /Q  Quiet install. Prevents the filter from displaying messages.
 /V  Verbose install. Displays some diagnostic messages.
 /W  Allows the virtual partitions to be written to.
 /A  Virtualize all partitions found. The only good reason to use
     this is along with the /M option when you want to control
     the mounting order of all the partitions. You must use the
     /W option if you use the /A option; otherwise OS/2 may crash
     when it tries to write to the partition.
     PLEASE NOTE: Using the /A option may change your drive
     letters causing the your system to be unbootable. Use
     the /M option together with /A. (This may change in the
     future.
 /M <mount list> Mounts the partitions in the order specified in the mount
     list, which should be a list of numbers separated by commas.
     The partitions are numbered 0 on a first come basis. (Not
     the OS/2 uses.)

 E.g. if you have one disk, the OS/2 Bootmanager installed and NT is on
 the first partition the correct options are
 BASEDEV=EXT2FLT.FLT /A /W /M 1

 <<=TIP=>> Windows NT 4.0 can use HPFS-Partitions if you have
 the pinball.sys out of NT 3.51 and the utility hpfs_nt4.zip
 by Chris Behnken, available at http://www.htc.net/~nbehnken.
 ATTENTION pinball.sys can only operate with disks or partitions
 up to 4GByte.

 <<=TIP=>> There is also an ALPHA NTFS.IFS by Daniel Steiner,
 available at http://npw.cgnet.de/dsteiner
-----------------------------------------------------------------
 OS/2 and Windows 98 or Windows 95

 Henk Kelder has developed an FREE FAT32.IFS
 it is available at http://www.os2ss.com/information/kelder/index.html
 and many other websides and bbs under OS2FAT32.ZIP
 Latest version is 0.81

 There is also an ALPHA of an VFAT.IFS, by Daniel Steiner,
 see above Tip.
-----------------------------------------------------------------
 OS/2 and Apple Hfs

 IFS=C:\HFSDIR\HFS.IFS

 Loads the Installable File System for reading Apple HFS-Drives
 and disks
 IF you make use of this IFS it must reside in front of the CDFS.ifs
 there are also needed the commands
 BASEDEV=HFSFLT.FLT in the config.sys, HFSFLT.FLT must reside in the
 OS2/BOOT directory
 and
 RUN=C:\HFSDIR\HFS.EXE

 The FREE HFS-Package by Marcus Better can be found at
 http://www.student.nada.kth.se/~f96-bet/HFS
 Unfortunately Marcus Better has stopped all development for OS/2
 There is also iHPFS by Marcus Better an package to make under
 plain old Dos HPFS formatted drives readable.
 See also the FREE HFS Utilities from the same author at http://
 www.student.nada.kth.se/~f96-bet/hfsutils/
-------------------------------------------------------------------
 OS/2 and T(oronto)V(irtual)F(ile)S(ystem).IFS

 Author:  Mark D. Leitch

 The TVFS provides a virtual OS/2 file system that combines symbolic links,
 search paths, and permissions.  Through the TVFS, local and remote file
 systems may be combined into a single, virtual file system.
 The FREE IBM EWS is available at many servers and BBS
 Latest version is 2.11

 <<=Tip=>> Kai Evers has developed an easy to use FREE PM-Interface for
 controlling and using the TVFS. It is available at
 http://www1.stuttgart.netsurf.de/~kevers/

 <<=TIP=>> See also TVFS-RM by Jürgen Dankoweits at http://www.geocities.com
 SiliconValley/Way/3792
-------------------------------------------------------------------
 OS/2 Ramdisk IFS

 Karl Olsen has developed an great FREE RAMFS-IFS available at
 http://home3.inet.tele.dk/kro

-----------------------------------------------------------------
8.  HOW TO RESTORE A DAMAGED CONFIG.SYS FILE FROM A BACKUP COPY.

 I moved the advice for OS/2 2.1 at the end as most users use
 Warp with his built-in backup option, instead you can find an
 advise how to get multiple configurations in Warp. (K.S.)

 In OS/2 Warp, IBM provides an archive feature which
 can be activated by opening your Desktop settings, click on the
 Archive Tab, and then click on "Create archive at every system
 restart".  With this feature activated, you can simply press
 Alt+F1 at boot and be presented with a menu which will allow you
 to boot with an alternate (backup) config.sys file.  See your
 user documentation for details.
-----------------------------------------------------------------
HOW TO GET MULTIPLE CONFIGURATION FILES IN WARP 3 or 4
-----------------------------------------------------------------
 Save your config.sys
 Make an ALTF1x.CMD file in /OS2/BOOT with the following content
 'copy \os2\boot\config.x \config.sys'
 Copy your Config.sys to \OS2\BOOT\CONFIG.X
 Edit CONFIG.X
 Repeat for ALTF1y.CMD ...
 Repeat for ALTF1z.CMD ...

 Now edit ALTF1TOP.SCR in \OS2\BOOT
 Insert 'X - Start config.x'
        'y - Start config.y'
        'z - Start config.z'

 ATTENTION ! for every line you insert you have to delete one !!
 for x and y you can use every letter that is not occupied by the
 Boot-Menu

 <<=TIP=>> The alternative config.* files can be easily edited by
 using configinfo, simply make an right mouseclick in the upper
 configinfo window and choose alternative config.sys

 Here's one sample for an German Warp 4

                           WIEDERHERSTELLUNGSOPTIONEN

   Waehlen Sie die zu verwendende Systemkonfigurationsdatei aus, oder
   geben Sie die Option ein, die dem gewuenschten Archiv entspricht.
   ESC - Der Systemstart wird mit der ungeaenderten Datei \CONFIG.SYS
         fortgesetzt.
   F2  - Eine Befehlszeile wird aufgerufen (keine Dateien werden ersetzt,
         die urspruengliche Datei CONFIG.SYS wird verwendet).
   F3  - Der Primaerbildschirm wird auf VGA eingestellt, und das System
         wird neu gestartet.
   F4  - Das System ueber die Option 'Installation anpassen' starten.
   F5  - Die Hardwareerkennung wird aktiviert.
   F6  - Die Hardwareerkennung wird inaktiviert.
   D   - Mit Dos und Windoze
   P   - OS/2 Pur (ohne Dos und Win)
   Durch Auswahl eines Archivs aus untenstehender Liste werden die aktuelle
   Datei CONFIG.SYS, das Verzeichnis der Arbeitsoberflaeche und INI-Dateien
   durch aeltere Dateien ersetzt. Diese aelteren Versionen koennen sich von
   den aktuellen Dateien unterscheiden. Die aktuellen Dateien befinden
   sich im Verzeichnis \OS2\ARCHIVES\CURRENT.
-----------------------------------------------------------------
HOW TO MAKE A BACKUP COPY OF YOUR Config and INI FILES in 2.X
-----------------------------------------------------------------
 A.  Boot OS/2 from the OS/2 Installation Disk.

 B.  Insert OS/2 Disk #1 when asked.

 C.  Press the ESC key when you get the first text screen.  By
     doing this you will be put into OS/2s command line mode.

 D.  Assuming that your backup copy of config.sys is in the root
     directory of "C" drive and is named CONFIG.SAV, enter the
     following command:

     COPY C:\CONFIG.SAV C:\CONFIG.SYS

     Press the ENTER key.

 E.  Remove OS/2 Disk #1 and reboot the system.

 What if you didn't make a backup copy?  IBM thought about you.
 When OS/2 was first installed on your system, the installation
 program made a backup copy of your original config.sys file.
 It stored this file in C:\OS2\INSTALL.  To restore from this
 file follow the same steps above, EXCEPT, in step "D" enter the
 following command instead of the one shown:

   COPY C:\OS2\INSTALL\CONFIG.SYS C:\CONFIG.SYS

 <<=TIP=>> Replace the config.sys file saved by the OS/2
 installation program in the INSTALL directory with your most
 current version, thus allowing you to restore from it.  If you
 are viewing this information using CNFGINFO.EXE, the Backup
 option is set to do this for you.

 CALL=C:\OS2\XCOPY.EXE C:\OS2\INSTALL\*.BK1 C:\OS2\INSTALL\*.INI /T /R /O
 CALL=C:\OS2\XCOPY.EXE C:\OS2\*.INI C:\OS2\INSTALL\*.BK1 /T /R /O

 Two files are essential to the operation of OS/2:  OS2.INI and
 OS2SYS.INI.  If these files should get trashed, OS/2 isn't going
 to function.  Backing them up is very important.  In OS/2
 version 2.0, once booted, OS/2 will not let you access or copy
 these critical files.  One way to circumvent this is to create
 your backups BEFORE OS/2 is booted.  This CALL will do the trick.
 It creates first a backup of your backup and then creates a
 backup of the original files.  This gives you a two generation
 backup.  This process will add time to your system boot.

 Generally OS/2 does not care where you place something in the
 config.sys file.  This CALL is an exception in version 2.0.  It
 must appear before any other line because you need to complete
 this backup process before OS2.INI AND OS2SYS.INI load.

 <<=NOTE=>>  In version 2.1, the INI files can be copied after
 the system is booted by using OS/2s COPY command, but you may
 wish to consider adding this CALL to your config.sys file to
 automate the process.

 <<=TIP=>>  OS2.INI and OS2SYS.INI can also be reconstructed at
 boot by holding down Alt-F1 during boot BEFORE the OS/2 logo
 appears.  You may need to hold the keys down for at least 20
 seconds.  During your initial installation of OS/2, the
 installation process stored a copy of its original INI files
 in the folder called INSTALL.  When you press Alt-F1 at boot,
 OS/2 moves these "backup" files into the OS/2 folder to
 replace the current versions.  The "CALL" shown above keeps
 the INI files in your INSTALL folder current.

 <<=WARNING=>>  If you are using a version of OS/2 before Warp,
 use the Alt-F1 key combination as a last resort because you may
 lose all customizing and changes you have made to the WpS.

 <<=NOTE=>>  The switches used mean the following:

      /T  -- allows xcopying of files with System attribute
      /R  -- allows xcopying of files with Read-only attribute
      /O  -- allows xcopying *onto* a file which has System,
             Read-only, or Hidden attribute.

-----------------------------------------------------------------
9.  REXX SUPPORT FROM WITHIN THE CONFIG.SYS FILE.

 The question of whether REXX programs can be called from within
 the config.sys file has been asked by a number of people.
 Russ Williams wrote to All:

  RW> Can anyone tell me what restrictions there are on running
  RW> REXX programs from config.sys (via "CALL=")?  It doesn't
  RW> work for me, and the on-line help is no help.

 You cannot.  The DLLs required to support Rexx are not loaded
 until Presentation Manager is loaded.  If you require Rexx
 support earlier, look for a program call SRVREXX at a fine BBS
 near you.

 Adding the line RUN=SRVREXX.EXE to the config.sys will
 immediately initialize Rexx.  You will then be able to access
 Rexx with or without PM being loaded.

-----------------------------------------------------------------
10. How to set the cache in system with less RAM

 ======================== Table 1.0 =============================

 If you have formatted your system with only HPFS partitions, the
 cache size in this statement, as set by OS/2 during installation,
 is that noted under ONE FILE SYSTEM in the table below.  If you
 have both FAT and HPFS partitions, then OS/2 sets the cache
 sizes to those noted under TWO FILE SYSTEM.  The file system
 which uses the greatest amount of your disk space gets the larger
 default value.

 MEMORY SIZE IN MB      TWO FILE SYSTEM         ONE FILE SYSTEM*
        4                     128/64                  128/48
        5                     128/64                  128/48
        6                     256/64                  256/128
        7                     256/128                 256/512
        8                     256/256                 384/512
        9                     256/256                 384
        10 - 16               512/512                 1024
        17 - 32               1024/1024               2048

 * Defaults in Warp are different and are shown as the second
   number.  On systems with more than 8MBs of RAM, the default
   is 10% of available RAM to a maximum cache of 4MB.


 ========================== Table 1.1 ===========================

 You can get better performance from your system by using your
 available RAM in the most efficient and effective way.  Select
 the case that best describes the file system or amount of RAM
 you use.

 CASE 1:  You use only HPFS or only FAT, but not both.

                               HPFS only.         FAT only.
 System memory of at least:  Set CACHE to:    Set DISKCACHE to:

                     16 MB+           2048                 2048
                     12 MB            1536                 1536
                      8 MB            1024                 1024

 CASE 2:  You use both HPFS and FAT with HPFS active and FAT
 passive.

 System memory of at least:  Set CACHE to:    Set DISKCACHE to:

                     16 MB+           2048            512 -1024
                     12 MB            1536            256 - 512
                      8 MB            1024            128 - 256

 CASE 3:  You use both HPFS and FAT with HPFS passive and FAT
 active.

 System memory of at least:  Set CACHE to:    Set DISKCACHE to:

                     16 MB+           1024                 2048
                     12 MB             768                 1536
                      8 MB             512                 1024

 <<=NOTE=>>  For purposes of the table above, "active" and
 "passive" are descriptors for the way a partition is used.
 If it is seldom used, it is "passive."  If a lot of disk
 intensive I/O occurs on the partition, it is "active."

---------------------------------------------------------------------

 11. Jerry Rowe's Warp Remote Install Page

 This page is a preliminary FAQ about installing OS/2
 Warp 4 over a laplink cable from a Server to a Client.

 First, you must set the Server up to use the parallel port
 (SSW Parallel MAC driver) network driver. You do this from
 MPTS [just type MPTS at the command line]. Select the driver,
 and add Netbios as a protocol.

 Then Edit the SSW Parallel MAC driver in MPTS and Note its
 address. It should be 40000000000A.

 Then open up the OS/2 Warp Remote Install object.
 Create the remote install disks. Be sure to use the same
 SSW Parallel MAC driver.
 Then edit the protocol.ini file on the 2nd disk. Inside it,
 insure that the MAC address is something
 other than 40000000000A. Using 40000000000B will work fine.
 Save the file.

 Now, shutdown and reboot the machine.
 Then examine \ibmcom\lantran.log and look for the reference
 to the Adapter # for the parallel port adapter. If you have
 another adapter in the Server, the number may be 1,
 otherwise it will be 0.

 Find Server Adapter #
 Note that the Adapter #=1 in the file below. If your parallel port
 is setup for adapter #=0, then lantran.log will be different.
 ==file lantran.log=========================================
 PARALLEL PORT MAC V 1.0 by Savant Software Inc. Copyright (C) 1994, 1995
 SAVANT SOFTWARE: PORT ADDRESS(ES): LPT1
 SAVANT SOFTWARE: PORT ADDRESS CONFIGURED: LPT1(378)
 IBM LANVDD is loaded and operational.
 IBM OS/2 LAN Netbind
 IBM LANDD is accessing IBM 802.3 LAN Interface.
 Adapter 1 was initialized and opened successfully.
 Adapter 1 is using node address 40000000000A. The Token-Ring
 format is 02000000
 IBM LANDD was successfully bound to MAC: pmac_nif->VECTOR.
 ==end file lantran.log=========================================

 Install service.exe and other files.

 If they were not installed during the Warp install,
 follow these instructions.

 Given that my CDRom drive is I:, and My Warp 4 drive is H:,
 issue this command:

 [H:\]I:\CID\SRVIFS\thinsrv /s:. /t:h:\cid\SRVIFS
 /r:h:\ibminst\tables\service.ini /tu:h:\

 THINSRV completed successfully.

 This creates a line in startup.cmd and creates startup.cmd
 if necessary.
 START H:\CID\SRVIFS\SERVICE.EXE /INI=SERVICE

 Thinsrv also adds:

 h:\cid\SRVIFS;

 to the PATH and DPATH statements in CONFIG.SYS.
 Because these changes will not take effect until a reboot,
 the command in STARTUP.CMD will not work until then.
 However, you can:

 cd \cid\srvifs service /ini=service

 to start it right away from the command line.

 You will probably want to remove the commands from Startup.cmd
 at this time to prevent the Server facility from running
 all the time.

 You may also want to create another cmd file with the service
 command in it if you would like to run it interactively.

 Edit h:\cid\service.ini

 Note Alias's and Path near bottom. Should be correct for the CD
 Note Adapter #. Should match # from Lantran.log.
 =============================================================
 ;SRVIFS INI file for OS/2 Warp Remote Install Server - 7CPESGDV
 Name = 7CPESGDV
 GroupName = NO
 Adapter = 1
 MaxClients = 5
 MaxFiles = 9999
 ClientWorkers = 8
 Path = I:\
 Alias = ReadOnly,Single,CDROM,I:\
 Alias = ReadWrite,Single,STATUS,H:\IBMINST\RSP\REMOTE
 ==============================================================

 With these changes made, shut down the computer and reboot.
 After it comes up, the GUI front
 end for the Remote install should work.

 ===Config.sys on disk 1 ===================
 CALL=A:\SRVATTCH.EXE z: \\7CPESGDV\CDROM
 DEVICE=A:\SRVIFS.SYS
 IFS=A:\SRVIFSC.IFS * /T
 CALL=A:\SRVATTCH.EXE w: \\7CPESGDV\STATUS
 RUN=Z:\CID\LOCINSTU\SRVREXX.EXE
 libpath=.;\os2\install;\os2\dll;z:\cid\locinstu;
 set os2_shell=cdboot.exe
 set oemprogram=\ibminst\npconfig.exe
 set exitwhendone=1
 set ADAPTER_NIF=PMAC.NIF
 set SRVNAME1=7CPESGDV
 set SAVECONNECT=1
 ================================================

 Now, change to H: [warp 4 drive] and start server.
 cd \cid
 SERVICE.EXE /INI=SERVICE

 Now, boot the client off the disk set.

 Should work. If it does not, check the hardware
 configuration of the parallel ports and insure they
 are set to bi-directional if that option is offered.

 I successfully installed Warp 4 on a Thinkpad using
 this method.

 After the install, you should also be able to network
 between the two computers over the laplink
 cable using OS/2 Peer.

---------------------------------------------------------------------

 12. THANKS

 Judy McDermott from Judy's Warped World at
 http://www.gt-online.com/~bri

 Kovacs Istvan <[e-mail]>

 Proportional Software and the DCF/2 development team.

 Jan van Wijk, author of DFSee, LPTool.

 Stefan Milcke

 Denis Tonn

 Oliver Poggensee the developer of Tyra/2
 The Config.sys editor for OS/2; [e-mail]

 Dan Carter ([e-mail])

 Doug Boulter

 OS/2 Inside

 Keith Medcalf

//END//