home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
OS/2 Shareware BBS: 8 Other
/
08-Other.zip
/
aptwarp2.zip
/
MRI.TXT
< prev
next >
Wrap
Text File
|
1996-04-27
|
4KB
|
99 lines
/* panel 1 */
The OS/2 Warp Installation Assistance Program
Next
Cancel
Help
Welcome to the OS/2 Warp Installation Assistance Program
The OS/2* Warp Installation Assistance Program prepares your Aptiva for the
installation of OS/2 Warp on your primary drive C partition; the same primary
drive C partition as Windows** 95**. Because your Aptiva came installed with
Windows 95, slight modifications must be made to your computer before you can
install OS/2 Warp. These modifications in no way interfere with any data on your
hard drive. Also, a dual boot feature will be set up for you, so that you can
start your computer from either Windows 95 or OS/2 Warp.
During installation you will be asked to insert the CD-ROM diskette 1. Be prepared
to create a replacement diskette for the CD-ROM diskette 1 that came with OS/2
Warp. This program will guide you through the creation of the replacement diskette.
* Trademark of the IBM Corporation.
** Trademarks of Microsoft Corporation.
/* reserved */
/* reserved */
To continue, click Next. If you are installing OS/2 Warp from diskettes,
click Help or F1 for information on installing OS/2 Warp
from Diskettes.
/* reserved */
/* reserved */
/* message box 0 */
Unpacking Files
The assistance program will unpack files for you and place them in the appropriate
locations. Click OK to start the unpacking procedure.
/* reserved */
/* dialog box 1 */
CD-ROM Drive Letter
OK
/* reserved */
The program detected the CD-ROM drive letter as follows. If that
is correct, click OK.
/* panel 2 */
CD
Diskette
Diskette 1 - Replacement Diskette
If you are installing OS/2 Warp from a CD, you must create a replacement diskette
for the CD-ROM diskette 1 that came with OS/2 Warp. You will need one 1.44 MB
diskette. Label the diskette Diskette 1 - Replacement Diskette. Insert the OS/2 Warp
CD into the CD-ROM drive. Insert the FORMATTED 1.44 MB diskette into drive A, and then
click CD. If you are installing OS/2 Warp from the Diskettes, click Diskette.
/* reserved */
/* reserved */
/* reserved */
/* reserved */
Sorry for the slight delay while the program creates the new diskette 1.
During this time, DO NOT remove the diskette or the CD.
/* message box 1 */
Overwrite
Since there is no match for your specified CD-ROM drive, the program will use
system selected CD-ROM drive letter to overwrite yours. OK? Click Cancel to exit.
/* message box 2 */
Check CD Drive
Sorry, we are unable to load files from your CD-ROM drive. Either your CD-ROM is
not ready or there is no CD in the drive.
/* message box 3 */
Check Disk Drive A
Sorry, we are unable to load files to your drive A. Check to see if you inserted
a FORMATTED 1.44 MB diskette in the drive A.
/* message box 4 */
Creating Diskette 1 - Replacement Diskette
Click OK to copy files to the diskette 1.
It may take a while.
/* message box 5 */
Unexpected Failure
The procedure was interrupted. You diskette may have failed. Please reformat the
diskette or replace the current diskette with new one, and restart the program.
/* reserved */
/* reserved */
/* reserved */
/* panel 3 */
More Instructions
Exit
Congratulations!
You have successfully made an updated OS/2 Diskette 1. You are now ready to
install OS/2 Warp from a CD.
Insert the OS/2 Warp Installation Diskette into drive A;
insert the OS/2 Warp CD into the CD-ROM drive;
click the Start button;
click Shutdown, and then select Restart the Computer?
When prompted remove the Installation Diskette from drive A. Insert the
Diskette 1 - Replacement Diskette, and press Enter.
/* reserved */
/* reserved */
/* reserved */
/* reserved */
/* reserved */
/* reserved */
Good Bye!
You are now ready to install OS/2 Warp from the Diskettes.
Insert the OS/2 Warp Installation Diskette into drive A;
click the Start button;
click Shutdown, and then select Restart the Computer?