ftp.uni-stuttgart.de/pub/systems/acorn//Acorn.tar/Acorn/riscos/tex-utils/tex-utils.spk/!dvips/config/lino

Text File | 1992-03-04 | 3KB | 94 lines

*
*   This configuration file is a sample one for a typesetter.  See the
*   end of the file especially, where we use setpageparams.  With a
*   configuration file like this, you can use
*
*   -t film0 -k -T 11in,17in
*
*   for instance to print an 11x17 inch document in orientation 0 with
*   crop marks.
*
*   Assume we have a nice modern lino with lots of memory.
*
m 1000000
*
*   And send output by default to a PostScript file.
*
o
*
*   Default resolution.  We must get this right!
*
D 1270
*
*   Compress the fonts.
*
Z
*
*   Paper size information.  First definition is the default.
*
*   If your default is a4 uncomment the following definition
*   and comment out the letterSize definition.
*
*@ a4size 210mm 297mm
*@+ %%PaperSize: a4

@ letterSize 8.5in 11in
@+ %%PaperSize: Letter

@ letter 8.5in 11in
@+ %%BeginPaperSize: Letter
@+ letter
@+ %%EndPaperSize

@ legal 8.5in 14in
@+ ! %%DocumentPaperSizes: Legal
@+ %%BeginPaperSize: Legal
@+ legal
@+ %%EndPaperSize

@ ledger 17in 11in
@+ ! %%DocumentPaperSizes: Ledger
@+ %%BeginPaperSize: Ledger
@+ ledger
@+ %%EndPaperSize

@ tabloid 11in 17in
@+ ! %%DocumentPaperSizes: Tabloid
@+ %%BeginPaperSize: Tabloid
@+ 11x17
@+ %%EndPaperSize

@ a4 210mm 297mm
@+ ! %%DocumentPaperSizes: a4
@+ %%BeginPaperSize: a4
@+ a4
@+ %%EndPaperSize

@ a3 297mm 420mm
@+ ! %%DocumentPaperSizes: a3
@+ %%BeginPaperSize: a3
@+ a3
@+ %%EndPaperSize
*
*   These last two are only for typesetters that can set the page size;
*   uncomment and put them in a `config.lino', for instance.
*
*   Use this for pages where you want the text to run in the same direction
*   as the film feeds (slow scan direction; down the length of the film.)
*   Best for everything *but* pages higher than the film is wide or pages
*   wider than they are tall; needed for pages wider than the film is wide.
*
@ film0 0in 0in
@+ statusdict /setpageparams known { vsize hsize 0 0 statusdict begin {
@+ setpageparams } stopped end } { true } ifelse { statusdict /setpage known
@+ { vsize hsize 0 statusdict begin { setpage } stopped pop end } if } if
*
*   Use this for pages where you want the text to run across the width of
*   the film (fast scan direction.)  Needed for pages taller than the film
*   is wide; preferred for pages wider than they are tall.
*
@ film1 0in 0in
@+ statusdict /setpageparams known { hsize vsize 0 1 statusdict begin {
@+ setpageparams } stopped end } { true } ifelse { statusdict /setpage known
@+ { hsize vsize 1 statusdict begin { setpage } stopped pop end } if } if