home *** CD-ROM | disk | FTP | other *** search
- This directory contains a version of the drivers that are required
- for the HP OmniBook 600 PCMCIA support. These drivers include a
- modified PCCARD.VXD, the HP Socket Services driver, and installation
- inf, (OB600SS.VXD and OB600SS.INF).
-
- The following instructions should be used to setup the protect mode
- PC Card (PCMCIA) support for the HP OmniBook 600C:
-
- 1) Copy PCCARD.VXD, OB600SS.INF, and OB600SS.VXD to a floppy disk.
- 2) Boot Win'95
- 3) Open the system properties page (click right mouse button on
- My Computer and then select properties is the quickest way).
- 4) Select the Device Manager.
- 5) Open the Other devices section.
- 6) Look at the properties for each Unknown Device to locate the
- one with resources "Interrupt Request 09" and "Input/Output
- Range 00EC-00ED". This is the socket controller device.
- 7) Select the Driver property page. It should say that no driver is
- installed. Click the Change Driver button.
- 8) In the "Select Hardware Type" box select PCMCIA socket and click OK.
- 9) In the "Select Device" box click have disk.
- 10) The "Install From Disk" box should show "Copy manufacturer's files
- from: A:\. Put the floppy in drive A: and press OK.
- 11) The Select Device box should now list "HP OmniBook 600 PCMCIA
- controller". Select it and click OK.
- 12) You should now be back in the device Properties page with a number
- of drivers listed (including ob600ss.vxd). Click OK.
- 13) Win'95 will now start copying files. It will ask for one of the
- Win'95 disks. If you have that disk on floppy insert it now.
- If you installed from CD or from the retail directory installed
- from your hard disk click OK. You will then get another dialogue
- box which allows you to change the source for copy files from.
- Make the necessary change and click OK.
- 14) After Win'95 completes copying the files you are returned to the
- properties page. Click OK.
- 15) You will get a "System Settings Change...do you want to restart your
- computer now?" dialog. Click YES.
- 16) System restart...wait patiently.
- 17) Reopen the System Properties Device Manager page. You should now
- see the HP OmniBook 600 PCMCIA controller with either a red splot
- or a yellow splot. Select it and open it's properties page.
- 18) Clear the active configuration check boxes and click OK.
- 19) Reopen the properties page and check the active configurations check
- boxes and click OK.
- 20) You should then see the Welcome to the PC Card (PCMCIA) Wizard dialog.
- Click next. (Note: make sure to set the No Yes selections correctly
- first.)
- 21) The next dialog gives you a chance to review the changes it is about
- to make to config.sys, autoexec.bat, and system.ini. You may click
- the Yes check box if you want to review or make changes to the
- drivers that are being commented out. Otherwise click No.
- 22) Next is the finished box. Click Finish.
- 23) Next you get another reboot box. Click Yes.
- 24) Press ctrl-alt-del when it says you can safely turn off the computer.
- 25) System restart...wait patiently.
- 26) Congratulations you have installed the protected mode PC Card drivers,
- but you still need to make one more change if you are running
- OBMGM.COM (check your config.sys file). If you are then you
- will need to add a line for OBMGM.COM in the IOS.INI file
- in you Windows 95 directory and reboot. This is necessary to
- get ATA and SCSI PC Cards to work properly.
-