home *** CD-ROM | disk | FTP | other *** search
/ Amiga Tools 2 / Amiga Tools 2.iso / hardware / vector-connection / doc / bugs < prev    next >
Encoding:
Text File  |  1995-03-09  |  6.8 KB  |  220 lines

  1.  
  2.                      V E C T O R - C O N N E C T I O N
  3.                      =================================
  4.  
  5.  
  6.                                   - BUGS -
  7.  
  8.                                              'What's up, doc?' -- Bugs Bunny.
  9.  
  10.  
  11.  
  12. Known Bugs and Problems:
  13. ========================
  14.  
  15.   ------------------------------------------------------------------------
  16.  
  17. There  is a lot of confusion on the PCB and in the manual about the numbering
  18. scheme  of  the  ports.   I  prefer (and I will use, if not other marked) the
  19. Commodore  counting  as  used  in  the  OpenDevice  call  (or  in  the 'Unit'
  20. Parameters  of  all Communication software).  So the ports are called 0, 1, 2
  21. and 3.  The count begins with '0'.
  22.  
  23. However,  on  the  PCB,  the counting starts with '1', so they're called '1',
  24. '2',  '3', '4'.  Yes, this is confusing.  In fact, it was so confusing that I
  25. couldn't  find  a bug for quite a while because I misunderstood a bug report.
  26. =:-(
  27.  
  28. I will in all documentation files *always* start counting with '0'.
  29. (I'm a computer science major, not an business major :-) ).
  30.  
  31.   ------------------------------------------------------------------------
  32.  
  33. On  *all*  PCB  revisions  up  to and including 2.7, on port '2' (this one is
  34. labeled  '3'  on  the  PCB, but it is '2' in the OpenDevice call), the signal
  35. lines for 'DSR' and 'CD' are swapped.
  36.  
  37. The  device supplied in this software release knows about this and fixes this
  38. problem  with  software.   If  you get a PCB of release 2.8 or above, you can
  39. *not* use this software release.  Look out for a newer release in the support
  40. boxes (See below).
  41.  
  42.   ------------------------------------------------------------------------
  43.  
  44. In some very rare (1:100) cases, the device can misjudge the clock speed of a
  45. board  and  take  a  'turbo'  (having  an 7.2328 MHz crystal) for an 'normal'
  46. (having  an  3.6864  MHz  crystal)  board.   This  will  give  you  baud rate
  47. mismatches.   You  can  solve  this problem with closing all device units and
  48. removing the device with 'avail flush'.
  49.  
  50. This  bug  is  well known and will be removed in a future release.  Please do
  51. not report it.
  52.  
  53.   ------------------------------------------------------------------------
  54.  
  55. Due  to  their  nature,  transfer rates of 76800 and 115200 bps are supported
  56. only on boards which have an 7.2328 MHz crystal installed.
  57. However,  there  is  no  warranty  for the reliability and stability of these
  58. transfer  rates  as  the  serial  chips  are  overclocked beyond their normal
  59. operating ranges when using these baud rates.
  60.  
  61.   ------------------------------------------------------------------------
  62.  
  63. Unlike other serial devices, the vectorser.device rejects all serial requests
  64. that  are  bigger than the set 'Receive Buffer'.  These requests are rejected
  65. with 'Error 4', that is 'BuffError' from devices/serial.h.
  66.  
  67. If  your  program  returns  requests  immediately  with 'Error 4', just try a
  68. bigger buffer setting in the VectorSer prefs program.
  69.  
  70.   ------------------------------------------------------------------------
  71.  
  72. The   well  known  GiftWare  Program  'Term'  by  Olaf  Barthel  ignores  the
  73. 'BufferSize' setting in the serial panel in versions up to 3.4.  You must set
  74. the  BufferSize  in  the  'VectorSer' program if e.g.  the xprzymodem.library
  75. gives  you  the  'Error 4' messages.  This bug is known and confirmed by Olaf
  76. and it will be fixed in later releases.
  77.  
  78.   ------------------------------------------------------------------------
  79.  
  80. There may be a problem with some 3rd Party Zorro II and III boards (e.g.  the
  81. Fastlane  Z3  SCSI  II  Hostadapter).  Most of these problems can be cured by
  82. cutting the PCB line to Pin 66 (DTACK) on the Vector Connection I/O board.
  83.  
  84.   ------------------------------------------------------------------------
  85.  
  86.  
  87. Known Compatibility risks:
  88. ==========================
  89.  
  90.  
  91. There is no warranty if you:
  92.  
  93. - use Programs written in 'GFA Basic'.
  94.  
  95. - use the 'Multiterm BTX program'.
  96.  
  97. This  software  was  not written according to the Commodore Amiga programming
  98. guidelines.
  99.  
  100. - use the Merlin Graphics board without the Hardware fixes from ProDev
  101.  
  102. This  hardware  was  not designed according to the Commodore Amiga Bus design
  103. specifications.
  104.  
  105. If  you  have  a  GVP  Harddisk  controller,  please use the latest available
  106. software release for this board.
  107.  
  108.  
  109. New Bugs (not mentioned in the section above):
  110. ==============================================
  111.  
  112. So you found a bug?  Fine.  Report it to us!  If you don't report it, we
  113. can't fix it.
  114.  
  115. Please use the form below:
  116.  
  117.  
  118.          --------------------------- cut ---------------------------
  119.  
  120.  
  121. 1) Your computer:
  122.  
  123. Computer (e.g. Amiga 3000):     _____________________________
  124.  
  125. OS-Version (e.g. 37.175):       _____________________________
  126.  
  127. CPU installed (e.g. 68030):     _____________________________
  128.  
  129. Board Revision (e.g. 6.2):      _____________________________
  130.  
  131. Other Boards installed:         _____________________________
  132.  
  133.                                 _____________________________
  134.  
  135.                                 _____________________________
  136.  
  137.                                 _____________________________
  138.  
  139.                                 _____________________________
  140.  
  141.  
  142. 2) The board:
  143.  
  144. Type (e.g. Vector Connection):  _____________________________
  145.  
  146. Software Revision (e.g. 2.0):   _____________________________
  147.  
  148. Board Revision (e.g. 2.7):      _____________________________
  149.  
  150.  
  151. 3) Your address:
  152.  
  153. Name:                           _____________________________
  154.  
  155. Street:                         _____________________________
  156.  
  157. Address:                        _____________________________
  158.  
  159. Country:                        _____________________________
  160.  
  161. Telephone:                      _____________________________
  162.  
  163. Fax:                            _____________________________
  164.  
  165. EMail (UseNet Notation please): _____________@_______________
  166.  
  167.  
  168. 3) Your software:
  169.  
  170. Software which showed problems: _____________________________
  171.  
  172. Version:                        _____________________________
  173.  
  174.  
  175.  
  176. 4)  Your problem (Please state it in German or English.  Feel free to include
  177. Enforcer Hits, Logs from your software, GIF or IFF pictures of problems etc):
  178.  
  179.  
  180.  
  181.  
  182.  
  183.  
  184.          --------------------------- cut ---------------------------
  185.  
  186.  
  187. Please fill out this form and FAX it to the following phone number:
  188.  
  189.               +49 (Germany) 221 / 369065 (HK Computer Cologne)
  190.  
  191. Please include a line 'ATTENTION:  Mr.  Scholz' in the Fax.
  192.  
  193.  
  194. You can also send it via regular Mail to
  195.  
  196. HK Computer
  197. Vector Connection Support
  198. Hoeniger Weg 220
  199.  
  200. D-50969 Koeln
  201. Germany
  202.  
  203.  
  204. Support BBS
  205. ===========
  206.  
  207. There  are  two  support BBSes, where you can find the latest releases of the
  208. Vector Connection Software.
  209.  
  210. QUASAR BBS:      +49-221-721633
  211. HK SUPPORT BBS:  +49-221-369024
  212.  
  213. Both are in Germany.
  214.  
  215. AmiNet
  216. ======
  217.  
  218. Beginning  with V 2.1 I will start to upload the software distribution to the
  219. AmiNet ftp-servers. Please see the 'README.AMINET' File.
  220.