home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
Network Support Encyclopedia 96-1
/
novell-nsepro-1996-1-cd2.iso
/
download
/
netware
/
drvkit.exe
/
LANDRV
/
ACER
/
386DRV
/
5220A.3X
next >
Wrap
Text File
|
1990-07-24
|
5KB
|
140 lines
Title: Readme File for Acer 5220A on NetWare 386 series
1. Table of Contents
This Readme File contains the information for users to use Acer 5220A
16-bit Ethernet card on NetWare 386 V3.X product series. It contains
the following files:
File Name Size in Bytes Date Stamp Time Stamp
-------------------------------------------------------------
ACERENET LAN 14459 6-07-90 3:02a
The file "ACERENET.LAN" is a LAN driver for the Acer 5220A 16-bit Ethernet
card. It appears either on the system diskette or on the DOS partition of
the server hard disk.
2. NetWare Setup Steps
a. Configuring the LAN Adapter
Follow the steps and, if necessary, refer to Acer 5220A
Ethernet Card User's Manual Chapter 3 for easy installation.
1. Verify the SW1 setting for I/O and memory base address
configuration.
2. If the memory space is used, set jumper group 1 (JP10 and JP28)
to the proper configuration.
3. Set the jumper plug to the proper jumper position on the
interrupt channel configuration block JP17 - JP27
4. Check the network interface used in the network system If thick
Ethernet is used, close all group 2 jumpers JP2 - JP9 i E position.
If thin Ethernet is used, close all group 2 jumpers in C position.
b. Installing the driver files for the card
Follow the 386 NetWare installation procedure until you reach
the ":" server console prompt. Enter commands listed below at
the prompt to install LAN driver into your server:
LOAD d:ACERENET.LAN <CR>
BIND IPX TO ACERENET <CR>
The drive letter d: is the physical location where "ACERENET.LAN" is
placed. You will be prompted to select the proper LAN card configuration
after the program is loaded.
3. Customer Support
Contact your local Acer network provider or call (800) NET-ACER within the U.S..
4. Driver Updates and Installation Manuals
You can get the updated drivers and manuals through your local distributors
or AcerServe Electronic Customer Service System.
5. Acer 5220A hardware setting quick reference:
a. Bit-Mapped Options for DIP Switchblock SW1
For Acer 5220A with board no. 48.07408.001
Switch Default
Number Function Setting
-------------------------------------------------
01 Memory segment address A16 1
02 Memory segment address A15 0
03 Memory segment address A14 0
04 Memory segment address A13 0
05 I/O base address A09 1
06 I/O base address A08 1
07 I/O base address A07 0
08 I/O base address A06 0
09 I/O base address A05 0
10 Not used 0
For Acer 5220A with board no. 48.07408.002
Switch Default
Number Function Setting
-------------------------------------------------
01 Enable/disable remote boot PROM 0
02 Memory segment address A16 1
03 Memory segment address A15 0
04 Memory segment address A14 0
05 Memory segment address A13 0
06 I/O base address A09 1
07 I/O base address A08 1
08 I/O base address A07 0
09 I/O base address A06 0
10 I/O base address A05 0
Default settings are I/O base address 300h and memory base segment address
D000h.
b. Interrupt request channel jumper setting
Set the shorting plug in the proper position when the desired interrupt
channel is selected.
For Acer 5220A with board no. 48.07408.001
Jumper Number Interrupt Channel
----------------------------------------
JP18 IRQ15
JP19 IRQ14
JP20 IRQ12
JP21 IRQ11
JP22 IRQ10
JP23 IRQ3 (default setting)
JP24 IRQ4
JP25 IRQ5
JP26 IRQ6
JP27 IRQ7
JP28 IRQ9
For Acer 5220A with board no. 48.07408.002
Jumper Number Interrupt Channel
----------------------------------------
JP17 IRQ15
JP18 IRQ14
JP19 IRQ12
JP20 IRQ11
JP21 IRQ10
JP22 IRQ3 (default setting)
JP23 IRQ4
JP24 IRQ5
JP25 IRQ6
JP26 IRQ7
JP27 IRQ9