TAP YIPL/TAP_and_YIPL_Collection_CD.iso/PHREAK/SYSINFO/ISDN2.TXT

Text File | 1995-04-25 | 48KB | 1,017 lines

2.01) What is ISDN?

ISDN stands for "Integrated Services Digital Networks", and it's a
ITU-T (formerly CCITT) term for a relatively new telecommunications
service package.  ISDN is basically the telephone network turned
all-digital end to end, using existing switches and wiring (for the
most part) upgraded so that the basic "call" is a 64 kbps end-to-end
channel, with bit-diddling as needed (but not when not needed!).
Packet and maybe frame modes are thrown in for good measure, too, in
some places.  It's offered by local telephone companies, but most
readily in Australia, Western Europe, Japan, Singapore, and portions
of the USA, and with other portions of USA asomewhat more behind.
In France, ISDN is known as "RNIS".

[e-mail] (Winston Seah)
[e-mail] (Fred R. Goldstein)
[e-mail] (Paul Antoine)
[e-mail] (Tilman Schmidt)
------------------------------

2.02) What does an ISDN network connection look like?

A Basic Rate Interface (BRI) is two 64K bearer ("B") channels and a single
delta ("D") channel.  The B channels are used for voice or data, and the D
channel is used for signaling and/or X.25 packet networking.  This is the
variety most likely to be found in residential service.

Equipment known as a Terminal Adapter (TA) can be used to adapt these
channels to existing terminal equipment standards such as RS-232 and
V.35.  This equipment is typically packaged in a similar fashion to
modems, either as standalone units or as interface cards that plug into
a computer or various kinds of commmunications equipment (such as
routers or PBXs).  TAs do not interoperate with the modem; they
replace the modem.

There may be cases where there is no need to interface to existing
terminal equipment or to emulate exisiting terminal equipment, or there
may equipment with synchronous interfaces present. In these cases,
standalone units or computer interfaces can provide high speed
synchronous connections to the B channels without converting to an
asynchronous standard.

Another common type of equipment can be used to implement a bridge
between local area networks using the ISDN channel to transport the
data.  These devices typically provide features such as demand
dialing and/or data compression.

Of course, more traditional devices such as telephones and fax machines
can be attached to the BRI, assuming they have the proper interface
hardware and software.

Another flavor of ISDN is Primary Rate Interface (PRI). Inside North
America and Japan, this consists of 24 channels, usually divided into
23 B channels and 1 D channel, and runs over the same physical
interface as T1. Outside of these areas the PRI has 31 user channels,
usually divided into 30 B channels and 1 D channel and is based on the
E1 interface.  It is typically used for connections such as one between
a PBX (private branch exchange, a telephone echange operated by the
customer of a telephone company) and a CO (central office, of the
telephone company) or IXC (inter exchange carrier, a long distance
telephone company).

[e-mail] (Kevin Collins)
[e-mail] (Dave Evans)
[e-mail] (Andrew Scherpbier)
[e-mail] (Dave Cherkus)
[e-mail] (Oliver Jones)
[e-mail] (Gary C. Kessler)
------------------------------

2.03) What will Basic Rate (2B+D) ISDN look like in my house/office?

An ISDN BRI U-Loop is 2 conductors from the CO (telephone company
central office) to the customer premises.  Its maximum length may be
5.5 km (18000 ft).  The equipment on both sides of the U loop has to be
carefully designed to deal with the long length of the U loop and the
noisy environment it operates in.

At the customer premises the U-loop is terminated by an NT1 (network
termination 1) device.  The NT1 drives an S/T-bus which is usually 4
wires, but in some cases it may be 6 or 8 wires.  In these optional
cases, the extra wires are used provide power to operate telephones
when normal power fails.  Alternately, 'phantom' power may be derived
from the standard four wires.  Outside of North America emergency mode
operation provides power for basic voice service only in the case of
loss of local power.  In emergency mode operation the NT1 receives up
to 1.2W from the central office. In North America there is no provision
for emergency mode operation.

The name of the S/T bus comes from the letters used in the ISDN
specifications used to refer to two reference points, S and T.  Point T
refers to the connection between the NT1 device and customer supplied
equipment.  Terminals can connect directly to NT1 at point T, or there
may be a PBX (private branch exchange, i.e. a customer-owned telephone
exchange).  When a PBX is present, point S refers to the connection
between the PBX and the terminal.  Note that in ISDN terminology,
"terminal" can mean any sort of end-user ISDN device, such as data
terminals, telephones, FAX machines, etc.

This picture shows what a residential ISDN connection looks like.

                Point T               Point U   |
    +--------+ 4-8 wires +-------+   2-4 wires  |
    |Terminal|-----+-----|  NT1  |-------------[| wall (to telco CO)
    +--------+     |     +-------+              |
    +--------+     |                            |
    |Terminal|-----+
    +--------+     |
                   :
    +--------+     |
    |Terminal|-----+
    +--------+

The T bus is a multipoint bus in this configuration.  It is sometimes
called the passive bus because there are no repeaters on the line
between the NT1 and the devices.  It can be implemented using the same
cable and connectors as is 10 base T Ethernet.  There may be up to 8
devices on the S/T bus.   The bus may be formed with splitters and T
connectors - it is a bus, not a star.  The D channel is used to control
the attachment of the one to eight devices to the two B channels.  No
two devices attach to the same B channel at the same time.

In this configuration, the major function of the NT is to allow more
than one device to have access to the 2 B channels provided by the ISDN
BRI.  For instance, you may have an ISDN telephone, an ISDN fax and an
ISDN computer interface attached to the BRI.  Each device can listen
for calls and only connect to a B channel when it identifies a message
requesting a service it can provide.

The NT1 only implements part of the channel sharing scheme; the other
devices participate as well, and the communication protocol used by the
NT1 and the other devices is an integral part of the scheme.  The NT1
also performs other functions; it translates the bit encoding scheme
used on the lines between it and the telephone company (the U loop) to
the encoding used between it and the devices.  These schemes are
different because the device to NT encoding was designed to enable
channel sharing whereas the NT to telco encoding was designed to allow
transmission across long distances.

In the United States, the customer pays for the NT device, so don't
forget to include the cost of this unit in your cost estimates, or if
you don't need the multiple device attachment feature, try to find a
device that does not require the NT device (i.e. it attaches directly
to the U loop).  If you are not in the United States the telephone
company provides the NT device, but remember there is no such thing as
a free lunch - you are probably paying for it through increased rates,
or increased taxes, etc. (flames to sci.economics or alt.talk.politics).

Unfortunately, the NT1 is not an inexpensive device.  It has to convert
between the signalling used on the U loop (which is operates over long
distances (5.5 km, 18000 ft) in a noisy environment and does not have
to deal with contention between devices) and the signalling of the S/T
bus (which operates over shorter distances in a quieter environment but
it does have to deal with contention between devices and other protocol
functions).  It also provides diagnostic functions such as loopback
mode, and it may have to provide power, as descibed above.

This picture shows what an ISDN connection looks like when a PBX is
present.

                Point S             Point T             Point U   |
    +--------+ 4-8 wires +-------+ 4-8 wires +-------+ 2-4 wires  |
    |Terminal|-----------|  NT2  |-----------|  NT1  |-----------[| wall
    +--------+           | (PBX) |           +-------+            |
                Point S  +---+---+                                |
    +--------+ _________/    |
    |Terminal|/              | Point S
    +--------+               |
                         +---+----+
                         |Terminal|
                         +--------+

In this configuration, the wires at points S and T are point-to-point
links.  Electrically, the S and T points are the same, which is why the
name S/T bus is almost always used.  This makes sense; the terminal
should see the same physical interface whether it is hooked up with or
without a PBX.  But, logically they are different.  The telephone
company needs to know that there is a PBX between itself and the user
so that it can coordinate its efforts with the PBX.  So, in cases where
the difference is important, the specifications use the S and T
terminology.

When there is no PBX in the configuration, the NT1 device is usually a
standalone device that is packaged a lot like a modem: in a small box
when there are only a few, and in a rackmount when you need a lot of
them.  In the United States, the customer buys the NT1 but in most of
the rest of the world the telephone company provides the NT1.  When
there is a PBX the rackmounted NT1s are quite common.  Also, when
there is a PBX the use of PRI lines instead of BRI lines is common.

[e-mail] (Dave Cherkus)
[e-mail] (Cliff Frost)
[e-mail] (Curt Welch)
[e-mail] (Dror Kessler)
[e-mail] (Eric Boll)
[e-mail] (Greg Larson)
[e-mail] (Kevin J. Rowett)
[e-mail] (Mark Anderson)
[e-mail] (Paul Antoine)
[e-mail] ( Patton M. Turner)
[e-mail] (Ronnie B. Kon)
------------------------------

2.04) What is a NT1?  Who sells them?

[ Ed Note: Some may feel that there's a bit of overlap between the
  preceeding sections and this one, but the preceeding sections are
  hard to write without integrating NT1 information and this one
  is so informative and well-written that it can stand on its own
  so I think I should leave it as is.  Comments? ]

Reply:  What's an NT1, why do I need one, and where do I get one?

An NT1 (network terminator 1) is a device which provides an interface
between the two-wire twisted pairs used by telephone companies in
their ISDN Basic Rate (BRI) network and an end-user's four-wire
terminal equipment.  The NT1 also provides power for the terminal
equipment if necessary (most ISDN phones need power from the NT1, but
most data terminal adapters--TAs--don't).

Most ISDN central office equipment (including AT&T 5ESS and Northern
Telecom DMS-100 switches) sends data to your home or office via what's
known in ITU-T lingo as a U interface on a single twisted pair.  The
NT1 hooks up to this twisted pair, and converts the signals from the U
interface to the four-wire S/T interface.  Most terminal equipment
(for example, the IBM Wave Runner add-in-card TA and most telephones)
offers the S/T interface.

In North America, you have to buy and maintain your own NT1 device.
The telephone company offers end-users a U interface.  In Europe and
Japan, the telephone company provides the NT1, owns it, and offers
end-users a S/T interface directly.  In North America, some ISDN
equipment vendors offer devices which connect directly to the U
interface (for example, the Combinet CB160).  If you have one of these
devices, you don't need to buy a separate NT1.  The U interface can't
be built in to the device when it's offered for sale in Europe or
Japan.  (This is unfortunate for vendors, who must build and test
separate products for the relatively small North American market if
they want to offer the convenience of a U-interface.)

Many types of NT1s require an external power supply, although some
include a built-in supply.  There are typically two classes of
external power supplies.  One class provides ten to twelve
watts--enough power for both the NT1 and for the terminal equipment.
The other class provides about two watts--enough power for the NT1
alone.  Many good power supplies offer at least a few seconds of
battery backup, to cover for glitches in line power.

Physically, the NT1 is a little plastic box with LEDs on it which can
be screwed to a wall.  The external power supply (if one is included)
is a typical plug-wart.  If you're using a lot of BRI lines, you can
buy a rack holding a dozen or so NT1s with a built in power supply.

It's a good idea to install your NT1 in a permanent fashion.  If you
unplug the ISDN line (the U interface twisted pair) from the NT1, it
shows up as a sign of line trouble in the central office.  Some
telephone companies respond to this so-called "trouble" by disabling
your ISDN line at the central office, and require you to place a
service call on your analog telephone to get your ISDN service
restored.

All the vendors shown here accept credit card orders and ship
promptly. All the vendors have well-organized telesales operations
with friendly and reasonably knowledgeable sales people. Prices are in
US dollars, as of 10/26/94, for single-unit purchases.  Pricing is
becoming volatile; competition seems to be heating up.

AT&T, Northern Telecom, and Tone Commander NT1s can be ordered from:
           Bell Atlantic Teleproducts
           West Building, Suite 150
           50 E. Swedesford Rd
           Frazer Pa,  19355
           tel [phone]  or 800-221-0845

Maker              Description       Part No.    Price
-----              -----------       --------    ------
Northern Telecom   NT1 standalone    IN51000     108.00
Northern Telecom   10w power supply  IN61000      72.00
Northern Telecom   2w power supply   IN61005      36.00
AT&T               NT1U-220          IA51007     276.00
AT&T               NT1U-230          IA51009     165.00
AT&T               10w power supply  IA61000     105.00
Tone Commander     NT1               IT51000     224.00
Tone Commander     2w power supply   IT61000      34.00


Tone Commander offers their own NT1 for sale.  Their sales literature
says it may be used as a drop-in replacement for the AT&T NT1U-220.

   Tone Commander Systems
   4379 150th Ave NE, PO Box 97039
   Redmond WA 98073-9739 USA
   [phone] or 800 524 0024
   fax [phone]
   They may refer you to a distributor such as
    Greybar Electric or Bell Atlantic.

Maker              Description       Part No.    Price
-----              -----------       --------    ------
Tone Commander     NT1 standalone    NT1U-220TC  185.25
Tone Commander     Power supply      901034       28.50


Adtran offers their own NT1 products for sale.

    Adtran, Inc.
    901 Explorer Blvd  Huntsville, AL 35806-2807 USA
    [phone]
    fax [phone]

Maker              Description       Part No.    Price
-----              -----------       --------    ------
Adtran             NT1               NT1 ACE     395.00
Adtran             Power Supply      PS2         150.00
Adtran             Power Kit                      74.00
Adtran             Standalone NT1    NT1/T400    575.00
                   (incl 7W supply)
Adtran             Rackmount NT1     NT1/T400    395.00


IBM sells the RoadRunner, an NT1 device with added value: it can
operate either as a standard NT1 or in extended mode. In extended mode
it provides an intergrated voice terminal adapter and a connection to
which POTS telephone devices (including modems, FAXs, and answering
machines) can be attached. This allow a home POTS line to be replaced
with an ISDN line.

When operating with a DMS-100 switch, one B channel is devoted to the
analog phones and one B channel is devoted to the data terminal
adapter.  When attached to a 5ESS switch, the B channels may be
allocated dynamically. The analog phones may use either B channel that
is available, and the data terminal device may use either or both B
channels.

The device includes a built in power supply and a back up battery,
providing up to 18 hours of on-hook, or 6 hours of off-hook operation
during a local power failure.

     IBM
     800-426-2255
     [phone]

Maker              Description       Part No.    Price
-----              -----------       --------    ------
IBM                7845 Network      82G6060     350.00
                   Terminator
                   Extended

Motorola UDS offers the NT100 Network Termination Unit.  This is an
NT1 with added value: a series of diagnostic tests can be chosen via a
front-panel rotary switch.

        Motorola UDS
        5000 Bradford Drive
        Huntsville AL 35805-1993
        [phone]
        800 451 2369
        fax [phone]

Maker              Description       Part No.    Price
-----              -----------       --------    ------
Motorola UDS       Net. Term. Unit   NT100

Thanks to the following people who helped uncover this information.
[e-mail] (Ed Tynan)
[e-mail] (Russell Pierce)
"H.A. Kippenhan Jr." <[e-mail]>
[e-mail]
The people who compiled the NIUF solutions catalog

Special thanks to [e-mail] (Oliver Jones) for editing this section.
------------------------------

2.05) Can the existing local loop lines be reused for ISDN?

The ISDN pairs are the same wires as used for regular telephone
service.  If you became an ISDN user at home, the same wire pair that
now provides your telephone service would be used to provide ISDN
(assuming you no longer have the regular line).

Most of the lines do not require any special conditioning.  Yes, if
a line has load coils on it they must be removed, BUT load coils
are usually only found on existing lines that are 15,000 feet or
longer.  As to lines with bridge taps, the 2B1Q line transmission
scheme (not to be confused with 2B + D channelization) is tolerant
of a certain amount of bridge taps and, therefore it is only a minimal
subset of existing lines (lines with bridge taps whose total length is
greater than 3000 feet for the bridge taps) that would require
special "de-conditioning."

With those things as the criteria, (in North America) we find than
generally around 90% or so of existing telephone lines need no
"de-conditioning" in order to be used for ISDN BRI service.

[e-mail] (sohl,william h)
------------------------------

2.06) How does this compare to regular phone lines?

The ISDN line may act like two independent phone lines with two numbers.
Depending on the CO equipment, conferencing features etc. may be available
(conferencing in the telephone switch).  BRI ISDN phones can support key-set
features such as you would expect to get on an office PBX like:
     - multiple directory numers per line.
     - multiple lines per directory number.
     - conferencing features.
     - forwarding features.
     - voice mail features.
     - speed call.
     - call park.
     - call pickup.
     - ring again.
     - textual status displays.

[e-mail] (Curt Welch)
[e-mail] (Greg Larson)
------------------------------

2.07) Is caller ID available on ISDN?

Caller ID (name or number display) may be supported (depending on the
CO setup). The availability of caller ID for residential phones would
depend on the capabilities of the local phone network and legislation
allowing or disallowing caller ID.  The availability of Caller ID
relies on the underlying switching protocol used by the switches
that make up the telephone system (e.g. SS7).

[e-mail] (Curt Welch)
[e-mail] (Greg Larson)
[e-mail] (Gary C. Kessler)
------------------------------

2.08) What do I get above and beyond plain old telephone service?

Plain old telephone service is transmitted between the central office
to your home or office telephone set (or modem, or fax) in analog
form.  At the central office, the analog signal is converted to a
series of digital samples at a rate of 8000 samples per second.  Each
sample is seven or eight bits in length.  As the signals for a
telephone call move around the central office, or between central
offices, they are transmitted in digital form.  Thus, a telephone call
consumes a transmission bandwidth of either 56 or 64 kilobits per
second.  The theoretical (Nyquist) limit for the frequency response of
a signal sampled 8000 times per second is 4kHz.  However, due to
various losses in the telephone system, the frequency response of an
ordinary telephone call is usually quoted as 3.1kHz.  Ordinary
modem-based data transmission uses schemes for encoding data in an
analog signal so it fits in this 3.1kHz bandwidth.  14.4kbps is a
commonly available transmission rate at the high end of the scale.
With this transmission rate, over three-quarters of the bitrate handled
by the central office is wasted.

Notice that in telephony, 64kpbs means 64000 bits per second, whereas
in computer engineering 64k bytes typically means 65536 bytes.

ISDN brings the digital signal all the way to your home or desktop.  With
ISDN, you can place a data call which uses all 56kbps or 64kbps, because
there is no need to convert the signal to analog in your modem and back
to digital at the central office.  The availability of the full bandwidth
presents some interesting technological opportunities:
   -- transmission of high-fidelity compressed audio
   -- transmission of encrypted audio
   -- transmission of lots of data
   -- transmission of other compressed signals, such as video

Basic-rate ISDN (BRI) offers two channels of this service.  In BRI, the
connection between your site and the central office offers 64kbps
bidirectionally on each channel.  Each of these channels may be used
for a voice call, for circuit-switched data, or for X.25 packet
switched data.  Thus, the existing POTS circuit [POTS: Plain Old
Telephone Service, i.e. traditional analog telephony] can be
conditioned to carry two calls at the same time.  (Your mileage may
vary;  you have to specifically order and pay for the various services
from your telephone company, just as you have to order and pay for Call
Waiting for an ordinary phone line.  Also, not all services are
available everywhere; X.25 connectivity between COs is a notable
problem in the Greater Boston area as of 9/93, for example.)

Incidentally, ISDN brings another interesting service to your home or
desktop:  a highly reliable 8000Hz clock signal.  In most cases, the
central office switches, long-distance carriers, and ISDN terminal
equipment all operate with exactly the same clock frequency.  In a
real-time communications environment (like a voice phone call) this
means that there's no need to compensate for differences between the
sampling rates at each end of the call.

One of the other features is that instead of the CO sending an AC ring
signal to activate your bell, it sends a digital packet that tells WHO
is calling (if available), WHAT TYPE of call (speech, datacomm?), the
NUMBER DIALED (maybe one of your aliases) and some other stuff. Your
equipment can then analyze this stuff and make an "intelligent" decision
what to do with it. For example, a phone (with speech-only capacity)
would completely ignore a datacomm call while a Terminal Adapter (ISDN
"modem") or a phone with built-in datacom functions would respond to it.
If you have several "aliases" tied to your line, you can program certain
phones to answer calls for certain numbers only.  Datacomm calls contain
baud rate and protocol information within the setup signal so that the
connection is virtually instantaneous (no messing around with trying
different carriers until both ends match).

[e-mail] (Curt Welch)
[e-mail] (Torsten Lif)
[e-mail] (Oliver Jones)
[e-mail] (Helge Oldach)
------------------------------

2.09) What do ISDN phones cost?

The ISDN sets can cost between $180 for an AT&T 8503T ISDN phone from
Pacific Bell up to $1900 depending on what/how many features are needed.

A recent report states that the price is $536.90 for an AT&T 7506 with
the RS-232 port on the back and $102.70 to get the 507A adaptor to hook
analog devices to my 7506.

Recent quotes were "$200" for a Coretelco 1800 and "$600" for a Fujitsu
SRS 1050.

[e-mail] (Dave Evans)
[e-mail] (Brad Huntting)
[e-mail] (Joe Ilacqua)
[e-mail] (Scott Turner)
------------------------------

2.10) Can you use existing telephone equipment with the voice portion?

Terminal Adapters (TA'a) are available that will interface non ISDN terminal
equipment (TE), called TE2 to the S/T interface.  At least one RBOC provides
a modem pool to allow for interchange of data with POTS subscribers.  Bellcore
may approve a standard to allow a analog pair to interface to POTS sets from
a NT1.  Also w/o a NT2 only one set can be connected to a B channel at a time.  This prevents 2 setsrom participating in the same voice call.

[e-mail] ( Patton M. Turner)
[e-mail] (Joe Ilacqua)
------------------------------

2.11) What is National ISDN?

Because of the breadth of the international ISDN standards, there are a
number of implementation choices that vendors of ISDN equipment can
make.  Given the number of choices vendors can make, different vendors
equipment may not interoperate.  In the United States, Bellcore has
released a series of specifications to try to avoid these
interoperability problems.  These are the National ISDN
specifications.  Contact the Bellcore ISDN hot line listed below for
more information.

[e-mail] (Gary C. Kessler)
[e-mail] (Dave Cherkus)
------------------------------

2.12) What is the NIUF?

North American ISDN Users Forum (NIUF) is an org. of ISDN-interested
parties, coordinated by NIST (National Institute of Stds. and Tech.)
Contact:

    NIUF Secretariat
    National Institute of Standards and Technology
    Building 223, Room B364
    Gaithersberg, MD  20899
    [phone] voice
    [phone] fax
    [phone] BBS  8N1  2400 bps

Bellcore has made the PostScript files for "A Catalog of National
ISDN Solutions for Selected NIUF Applications, Second Edition"
accessable via anonymous ftp from the machine info.bellcore.com.
This document has a tremendous amount of information about
ISDN products and vendors, among many other things.  See the item
below for details.

The currently approved documents for the Application Software
Interface (ASI) from the North American ISDN User's Forum (NIUF)
are available via anonymous FTP from dsys.ncsl.nist.gov.  The
documents are in Postscript and found in uncompressed ASCII (foo.ps),
compressed (foo.Z) and zipped (foo.zip) files.

These documents describe the Implementation Agreements made by the
NIUF for an API to ISDN services.

The file sizes are approximate and intended to help determine space
requirements for transfer.

Part 1: Overview and Protocols - Approved: 10/4/91, Updated: 10/30/92
        ~ftp/asi/docs/part1.ps  - 347853 bytes
        ~ftp/asi/docs/part1.Z   - 119655 bytes
        ~ftp/asi/docs/part1.zip -  89545 bytes

Part 2: MS-DOS Access Method - Approved: 6/5/92
        ~ftp/asi/docs/part2.ps  - 146474 bytes
        ~ftp/asi/docs/part2.Z   -  44450 bytes
        ~ftp/asi/docs/part2.zip -  31599 bytes

Part 3: Enhanced DOS/Protected Mode Shell Access Method -
                Approved: June 5, 1992, Updated: 10/30/92
        ~ftp/asi/docs/part3.ps  - 285344 bytes
        ~ftp/asi/docs/part3.Z   -  91273 bytes
        ~ftp/asi/docs/part3.zip -  68331 bytes

Part 4: UNIX Access Method - Approved: 10/30/92
        ~ftp/asi/docs/part4.ps  - 151809 bytes
        ~ftp/asi/docs/part4.Z   -  47765 bytes
        ~ftp/asi/docs/part4.zip -  33465 bytes

For further information regarding these documents please contact
Robert Toense ([e-mail]) (phone: [phone]).

[e-mail] (Dave Cherkus)
[e-mail] (Vance Shipley)
------------------------------

2.13) What is ATM?

ATM (Asynchronous Transfer Mode) is a switching/transmission technique
where data is transmitted in small, fixed sized cells (5 byte header,
48 byte payload).  The cells lend themselves both to the time-division-
multiplexing characteristics of the transmission media, and the packet
switching characteristics desired of data networks.  At each switching
node, the ATM header identifies a "virtual path" or "virtual circuit"
that the cell contains data for, enabling the switch to forward the
cell to the correct next-hop trunk.  The "virtual path" is set up
through the involved switches when two endpoints wish to communicate.
This type of switching can be implemented in hardware, almost essential
when trunk speed range from 45Mb/s to 1Gb/s.

One use of ATM is to serve as the core technology for a new set of ISDN
offerings known as Broadband ISDN (B-ISDN).

For more information, read comp.dcom.cell-relay.

This group has a Frequently Asked Questions list;  it is posted
to news.answers and is in various archives as cell-relay-faq.

[e-mail] (Art Berggreen)
[e-mail] (Dave Cherkus)
------------------------------

2.14) What is B-ISDN?

Broadband ISDN refers to services that require channel rates greater than
a single primary rate channel.  While this does not specificially imply
any particular technology, ATM will be used as the switching infrastructure
for B-ISDN services.

B-ISDN services are categorized as:

    INTERACTIVE
     Conversational -- such as videotelephony, videoconferencing, ...
     Messaging -- such as electronic mail for images, video, graphics,...
     Retrieval -- such as teleshopping, news retrieval, remote education,...

    DISTRIBUTION
     Without user presentation control -- electronic newspaper, electronic
         newspaper, TV distribution
     With user presentation control -- remote education, teleadvertising,
         news retrieval

More information: ITU ITU-T Rec. I.211.

[e-mail] (Gary C. Kessler)
------------------------------

2.15) What is BONDING?

An inverse multiplexing method of the Bandwidth ON Demand
INteroperability Group, implemented by most (all?) inverse multiplexor
vendors to interoperate with inverse multiplexors of other vendors.

BONDING is a set of protocols developed by U.S. inverse multiplexor
that supports communication over a set of separate channels as if their
bandwidth were combined into a single coherent channel.  For example it
supports a single 384 kb/s data stream over 6 64 kb/s channels.

The specification defines a way of calculating relative delay between
multiple network channels and ordering data such that what goes in one
end comes out the other.

Most (all?) vendors also have their own proprietary methods that
usually add features and functions not present in BONDING mode 1.  Mode
1 is the mode used for recent interoperability testing between vendors.

Chip Sharp at Teleos has made available electronic copies of the
BONDING (Bandwidth on Demand Interoperability Group) 1.0 and 1.1
specifications.  The specs are available via WWW, gopher, anonymous
FTP, DECnet COPY, and AFS (see instructions below).

The following files are available:

- aaareadme-networks       help file (in ascii text)
- bdmain.doc               main body of BONDING 1.0 specification
                           (Word for Windows 2.0 format)
- bdmain.ps                main body of BONDING 1.0 specification (Postscript)
- bdannex.doc              annex of BONDING 1.0 specification (Word
                           for Windows 2.0 format)
- bdannex.ps               annex of BONDING 1.0 specification (Postscript)
- bd_v1_1.doc              changes for BONDING 1.1 specification (Word
                           for Windows 2.0 format)
- bd_v1_1.ps               changes for BONDING 1.1 specification (Postscript)

Transfer Instructions:

WWW:
    server: www.hep.net
    URL: gopher://www.hep.net:70/11/info_center/networks/bonding

Gopher:
    server: gopher.hep.net
    Bookmark:
    Name=Bandwidth on Demand Interoperability Group (BONDING) Documents
    Type=1
    Port=70
    Path=1/info_center/networks/bonding
    Host=gopher.hep.net

Anonymous FTP:
    server: ftp.hep.net
    directory: networks/bonding

DECnet COPY (only for those on HEP-NSI DECnet):
    HEPNET::[ANON_FTP.NETWORKS.BONDING]

AFS:
    /afs/hepafs1.hep.net/public/anon_ftp/networks/bonding

[e-mail] (Marco S Hyman)
"Bob Larribeau" <[e-mail]>
"David E. Martin" <[e-mail]>
------------------------------

2.16) Data Encapsulation for IP over ISDN

A decision was made at the Amsterdam IETF to state that all systems
wishing to guarantee IP interoperability should implement PPP.  Such
systems may also implement the Frame Relay or X.25 encapsulations, and
an RFC will be published delineating how, when it is known that the
encapsulations are limited to that set of three, they may be
distinguished by examination of the first correctly checksummed and
HDLC bit-stuffed packet.

Many implementations are using PPP so that they can negotiate
compression and/or multilink operation.

There is an Internet Draft from the Point-to-Point Protocol Working
Group of the Internet Engineering Task Force that describes the use of
PPP over ISDN.  This draft is named draft-ietf-pppext-isdn-NN.txt in
the internet-drafts Shadow Directories on nic.ddn.mil, nnsc.nsf.net,
nic.nordu.net, ftp.nisc.sri.com, munnari.oz.au, Germany.EU.net and on
many, many other mirror archives.  This is also discussed in RFC 1356
by Malis, et. al.

A common practice in most European countries is raw IP packets
delimited by HDLC flags.  Another common practice is an encapsulation
using simple HDLC in layer 1, X.75 (LAPB, usually I-frames) in layer 2
and, sometimes, T.70 in layer 3.  PPP is used instead of HDLC/X.75/T.70
when the network doesn't provide the callers telephone number eg. when
emulating a modem or the callers number is lost on telephone company
borders.  In this case, caller authentication is done via PAP/CHAP
instead.

[e-mail] (Keith Sklower)
[e-mail] (Dave Cherkus)
[e-mail] (Gary C. Kessler)
[e-mail] (Juergen Ernst Guenther)
[e-mail] (Carsten)
------------------------------

2.17) Full Motion Video over ISDN

In ISDN, video isn't a "service being offered" - at least not for
low/midrange quality. You buy the proper equipment for both
subscribers, plug it in, and place the call. Just like speaking French
on ISDN isn't something being offered - it is something you just do,
yourself.

Video telephony over narrowband ISDN is governed by a suite of ITU-T
(formerly CCITT) interoperability standards.  The overall video
telephony suite is known informally as p * 64 (and pronounced
'p star 64'), and formally as standard H.320.   H.320 is an "umbrella"
standard;  it specifies H.261 for video compression, H.221, H.230, and
H.242 for communications, control, and indication, G.711, G.722, and
G.728 for audio signals, and several others for specialized purposes.
A common misconception, exploited by some equipment manufacturers, is
that compliance with H.261 (the video compression standard) is enough
to guarantee interoperability.

Bandwidth can be divided up among video, voice, and data in a
bewildering variety of ways.  Typically, 56kbps might be allocated to
voice, with 1.6kbps to signalling (control and indication signals) and
the balance allocated to video.

An H.320-compatible terminal can support audio and video in one B
channel using G.728 audio at 16 kb/s.  For a 64 kb/s channel, this
leaves 46.4 kb/s for video (after subtracting 1.6 kb/s for H.221
framing).

The resolution of a H.261 video image is either 352x288 (known as CIF)
or 176x144 (known as quarter-CIF or QCIF).  The frame rate can be
anything from 30 frames/second and down.  Configurations typically use
a 2B (BRI) or a 6B (switched-384 or 3xBRI with an inverse multiplexer)
service, depending on the desired cost and video quality. In a 384kbps
call, a video conferencing system can achieve 30 frames/second at CIF,
and looks comparable to a VHS videotape picture. In a 2B BRI call, a
standard video phone can achieve 15 frames/second at CIF.

Those who have seen the 1B video call in operation generally agree that
the quality is not sufficient for anything useful like computer based
training - only for the social aspect of being able to *see* Grandma as
well as hear her (sort of like the snapshot pictures you make with that
$5 camera with no controls).

A 2B picture, on the other hand, is for all practical purposes
sufficient for remote education, presentations etc. Rapidly changing
scenes are still not very well handled, but as soon as the picture
calms down, the sharpness and color quality are impressive (considering
that only two plain phone channels are being used). With 2B+D being the
standard BRI, this kind of picturephone will be usable "everywhere"
(including private homes).

However, it should still be noted that 6xB or H0 does allow for dramatic
improvement in picture quality compared to 2xB.  In particular, H.320
video/audio applications will often allocate 56kbps for audio, leaving
only 68.8kbps for video when using 2xB.  On the other hand, using H0
would get you 326.4kbps for video with 56kbps for audio. Alternative
audio algorithms can improve picture quality over 2xB by not stealing
as many bits.  Note that 6B is not identical to H0; the latter is a
single channel which will give you 80kbps above that of six separate B
channels.  Inverse multiplexors can be used to combine B channels.

[e-mail] (Ketil Albertsen,TIH)
[e-mail] (Kevin Davis)
[e-mail] (Oliver Jones)
[e-mail] (Mike Souryal)
------------------------------

2.18) What is a SPID? How come my ISDN device won't work without one?

SPIDs are Service Profiles IDs.  SPIDs are used to identify what sort
of services and features the switch provides to the ISDN device.
Currently they are used only for circuit-switched service (as opposed
to packet-switched).  Annex A to ITU recommendation Q.932 specifies the
(optional) procedures for SPIDs.  They are most commonly implemented by
ISDN equipment used in North America.

When a new subscriber is added, the telco personnel allocate a SPID
just as they allocate a directory number.  In many cases, the SPID
number is identical to the (full ten digit) directory number.  In other
cases it may be the directory number concatinated with various other
strings of digits, such as digits 0100 or 0010,  1 or 2 (indicating the
first or second B channel on a non-centrex line), or 100 or 200 (same
idea but on a centrex line) or some other, seemingly arbitrary string.
Some people report SPIDs of the form 01nnnnnnn0 for  AT&T custom and
01nnnnnnn011 for NI-1, where n is the seven digit directory number.
It is all quite implementation dependent.

The subscriber needs to configure the SPID into their terminal (i.e.
computer or telephone, etc., not their NT-1 or NT-2) before they will
be able to connect to the central office switch.

When the subscriber plugs in a properly configured device to the line,
Layer 2 initialization takes place, establishing the basic transport
mechanism.  However if the subscriber has not configured the given SPID
into their ISDN device, the device will not perform layer 3
initialization and the subscriber will not be able to make calls.  This
is, unfortunately, how many subscribers discover they need a SPID.

Once the SPID is configured, the terminals go through an
initialization/identification state which has the terminal send the
SPID to the network in a Layer 3 INFOrmation message whereby the
network responds with an INFO message with the EID information element
(ie). Thereafter the SPID is not sent again to the switch. The switch
may send the EID or the Called Party Number (CdPN) in the SETUP message
to the terminal for the purpose of terminal selection.

SPIDs should not be confused with TEIs (terminal endpoint identifiers).
TEIs identify the terminal at Layer 2 for a particular interface
(line).  TEIs will be unique on an interface, whereas SPIDs will be
unique on the whole switch and tend to be derived from the primary
directory number of the subscriber.  Although they are used at
different layers, they have a 1-to-1 correspondence so mixing them up
isn't too dangerous. TEIs are dynamic (different each time the terminal
is plugged into the switch) but SPIDS are not. Following the
initialization sequence mentioned above the 1-to-1 correspondence is
established.  TEIs are usually not visible to the ISDN user so they are
not as well known as SPIDs.

The "address" of the layer 3 message is usually considered to be the
Call Reference Value (also dynamic but this time on a per call basis)
as opposed to the SPID, so the management entity in the ISDN device's
software must associate EID/CdPN on a particular TEI and Call Reference
Number to a SPID.

There are some standards that call for a default Service Profile, where
a terminal doesn't need to provide a SPID to become active.  Without
the SPID however, the switch has no way of knowing which terminal is
which on the interface so for multiple terminals an incoming call would
be offered to the first terminal that responded, rather than to a
specific terminal.

[e-mail] (winston (w.l.) sorfleet)
[e-mail] (Chuck Storry)
------------------------------

2.19) Will ISDN terminal equipment that works in one country
               work properly when it is installed in another country?

There are four major problem areas.

The first has to do with voice encoding, and is only a problem if the
equipment is a telephone.  Equipment designed for use in North America
and Japan uses mu-law encoding when converting from analog to digital,
whereas the rest of the world uses A-law.  If the equipment has a
switch for selecting one or the other of these encoding types, then
there will not be a problem with the voice encoding.

The second has to do with the way the equipment communicates with the
telephone exchange.  There are interoperability problems because
 * there are so many different services (and related parameters) that the
   user can request and
 * each country can decide whether or not to allow the telephone exchange
   to offer a given service and
 * the specifications that describe the services are open to interpretation
   in many different ways.
So, as with other interoperability problems, you must work with the vendors
to determine if the equipment will interoperate.  This is a basic problem;
it impacts all ISDN equipment, not just voice equipment.

The third has to do with homologation, or regulatory approval.  In most
countries in the world the manufacturer of telephone equipment must
obtain approvals before the equipment may be connected to the network.
So, even if the equipment works with the network in a particular
country, it isn't OK to hook it up until the manufacturer has jumped
through the various hoops to demonstrate safety and compliance.  It is
typically more expensive to obtain world-wide homologation approvals
for a newly-developed piece of ISDN equipment than it is to develop it
and tool up to manufacture it.

A fourth issue is in the US the TA and NT1 are both provided by the
customer, while in Europe the NT1 is provided by telephone company.
Stated differently, if you walk into a store in the US and buy
something to plug into an ISDN line it may be designed as a one-piece
unit that connects to point U.  In Europe you would get something that
plugs into point T.  Thus you might take a piece of US-originated
equipment to Europe and find that it won't work because the jack in
Europe is a T interface and the plug on your US equipment is a U
interface.

There are attempts to remedy this situation, particularly for BRI
ISDN.  In North America, the National ISDN User's Forum is coming
up with standards that increase the uniformity of ISDN services.
In Europe, a new standard called NET3 is being developed.

[e-mail] (Ming Sun)
[e-mail] (Marco S Hyman)
[e-mail] (Jim Breen)
[e-mail] (Dave Evans)
[e-mail] (Oliver Jones)
[e-mail] (William Martin)
[e-mail] (Carl Oppedahl)
------------------------------

2.20) Will ISDN terminal equipment that works with one vendor's ISDN
               switch work properly when used with another vendor's switch?

[Ed. Note: The title is edited from the previous faq to try to fit in
  with the preceding question]
[Also, this seems to imply that there are only two implementations
 to worry about and it is very US-centric.  This section needs to be
 reworked]

When the National ISDN-1 standard is implemented, there will be a single
standard for how TE communicates with the CO (the call setup dialogue).
Until that time, you may encounter two different varieties of CO equipment,
each with its own call setup dialogue:
  * ATT 5ESS
  * Northern Telecom DMS100
Some ISDN TE equipment can be configured to communicate with either;
some works with only one variety.

[e-mail] (Jim Rees)
[e-mail] (Jerry Scharf)
------------------------------

2.21) Do different manufacturers' Terminal Adaptors interoperate when
               used asynchronously?

There is a standard up to 19.2k (V.110) but above that there is no real
standard implemented. However, in practice there is a fair degree of
interoperability (even when the TA's manual tells you otherwise)
because many TAs use the same chip set (supplied by Siemens) which
happily goes up to 38.4. TAs from different suppliers that are using
the Siemens chips have a fair chance of interoperating at up to 38.4k.

[e-mail] (William Martin)
------------------------------

2.22) Why do I get only about 19.2k throughput from my TA?

The problems in using TA's are the same as those in using fast modems.
You only get the throughput that your serial port can handle. The
serial ports of many machines struggle to receive at 19.2k. Sending is
easier to implement efficiently.  Many machines will happily send data
to a TA at 38.4, but choke down to around 19.2k or lower when receiving
(with lots of retries on ZMODEM file transfer).

[e-mail] (William Martin)
------------------------------

2.23) How long should call setup take when using a TA?

The "less than a second" call setup sometimes claimed seems to be rare.
TAs have a negotiation phase and it typically takes around 4 seconds
to get through to the remote site.

[e-mail] (William Martin)