home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
Shareware Supreme Volume 6 #1
/
swsii.zip
/
swsii
/
163
/
MCRPSPEC.ZIP
/
1650SPEC.TXT
< prev
next >
Wrap
Text File
|
1989-09-15
|
7KB
|
156 lines
MICROPOLIS 1650 DISK DRIVE
SPECIFICATIONS
Model Number
Unformatted Capacity: 1653-4 1653-5 1654-6 1654-7
Total Mbytes 104.0 130.0 156.1 182.1
Disk Platters 3 3 4 4
Read/Write Heads 4 5 6 7
Cylinders ---------------- 1249 -----------------
Bytes per track -------------- 20,832 -----------------
Formatted Capacity
Total Mbytes 92.0 115.0 138.0 161.0
Bytes per Sector ----------------- 512 -----------------
Sectors per Track ----------------- 36 -----------------
PC Drive Types.
If you are using third-party installation software or an board
BIOS on the controller, follow the instructions included with
the software or controller. Otherwise, examine the entries in
your drive table and find the type that most resembles the head
and cylinder parameters of the drive without exceeding these
parameters.
Performance Specifications
Seek Time (including settling time) Track-to-Track 4 msec
Average 16 msec
Maximum 37 msec
Avg Rotational Latency 8.33 msec
Rotational Speed 3600 rpm +/- 0.5%
Data Transfer Rate 10 Mbits/sec
MTBF 150,000 hours
Positioner Fully balanced rotary voice coil
Parking Automatic park and lock
General Functional Specifications
Interface ESDI
Sectoring (see W1 description, below) Hard or Soft
Write Precompensation Start Cylinder 1249 *
Reduced Write Current Start Cylinder 1249 *
Landing Zone 1249
Mounting Plane Any orientation
* These are effectively turned off by specifying a non-existent
cylinder. Some systems accomplish this by using a value of "-1"
Power Requirements
+12V +/-5% 0.9A Avg
(2.0A max. during start-up)
+5V +/-5% 0.7A avg
Power dissipation, typical 14 Watts
Drive Addressing and Interface Termination
NOT
USED J2 J1 J3
____ ___________ _________________ ________ Power
| | | |1| | |1| || Power | (under
| |_| |_____| |_| -------| board)
| |
| |
| Terminator |
| |
| |
| |
| |
| |
| |
| DA1 |
| DA2 |
| DA3 (Component side) |
| W5 |
| W4 |
| W3 |
| W2 |
| W1 |
RN1 Interface Terminator
The Interface Terminator factory installed at RN1 will provide
proper termination for the interface lines. When daisy-chaining
multiple drives, leave the terminator installed only in the last
physical drive on the daisy chain; remove the terminator from
each of the other drives. In most PC/AT installations, the C:
drive is actually at the end of the cable and should retain the
terminator.
DA1, DA2, DA3 Drive Address Jumpers
The drive address jumpers are identified as DA1, DA2 and DA3.
Address selection is binary, as shown in the table below. The
ESDI controllers's documentation will specify the drive address
to use.
Drive Select Jumpers
Address DA3 DA2 DA1
------- --- --- ---
1 out out in
2 out in out
3 out in in
4 in out out
5 in out in
6 in in out
7 in in in
"Drive address 0" (no jumper at DA1, DA2, or DA3) is a "deselect"
(i.e., no drive selected). Drives are factory configured as Drive
Address 1. For many multiple drive installations, each drive must
have a unique address. An exception is that for every drive in
a PC/AT installation, verify that only Drive Address is at DA2;
move the jumper if necessary(the special twisted interface cable
that is generally used takes care of assigning a unique address
to each drive). PC/AT controller can typically support a maximum
of two drives.
W5 Selects the Spindle Control Option.
W5 selects the spindle a control option. If W5 is installed, the
drive waits for a Start Spindle command (after power is applied)
to start the spindle motor. If W5 is not installed (the factory
default configuration), the drive automatically starts the spindle
motor at power-on. W5 is not installed for PC/AT applications.
W1 Selects the Sectoring Mode.
If W1 is installed, the drive operates in the soft-sectored mode.
If W1 is not installed (the factory default configuration), the
drive operates in the hard-sector mode. W1 is not installed for
most PC/AT in applications.
W2, W3, W4 Sector Size Option
The number of bytes per sector may be specified using the Set
Bytes Per Sector command or by selecting a default sector
configuration with jumpers W2, W3, and W4 as follows:
Jumpers Sectors Bytes/Sector
W4 W3 W2 Per Track Formatted Unformatted
--- --- --- --------- --------- -----------
out out out 35 512 595
-------------------------------------------------------------
| * out out in 36 512 578 |
-------------------------------------------------------------
out in out 19 1024 1096
out in in 9 2048 2314
in out out 5 4096 4166
in out in 32 512 651
in in out 64 256 325
in in in 1 20,832 20,832
* This is the default (factory installed) configuration and is
recommended for PC/AT applications