home *** CD-ROM | disk | FTP | other *** search
/ Share Gallery 1 / share_gal_1.zip / share_gal_1 / HR / HR002.ZIP / POL2D < prev    next >
Text File  |  1988-03-12  |  14KB  |  487 lines

  1.  
  2.  
  3.  FCC Novice Exam Question Pool.   Subelement 2D.
  4.  Amateur Radio Practice.     4 Questions.
  5.  
  6.  
  7.   One (1) question must be from the following:
  8. ------------------------------------------------
  9.  
  10. 2D 1.1   B
  11. How can an Amateur Station be protected against being
  12. operated by unauthorized persons?
  13.  
  14.  A. Install a carrier operated relay in the main power line.
  15.  B. Install a key operated ON/OFF switch in the main power line.
  16.  C. Post a "Danger - High Voltage" sign in the station.
  17.  D. Install AC line fuses in the main power line.
  18.  
  19.  
  20. 2D 2.1   D
  21. Why should all antenna and rotor cables be grounded
  22. when an Amateur Station is not in use?
  23.  
  24.  A. To lock the antenna system in one position.
  25.  B. To avoid radio frequency interference.
  26.  C. To save electricity.
  27.  D. To protect the station and building from 
  28.     damage due to a nearby lightning strike.
  29.  
  30.  
  31. 2D 2.2   C
  32. How can an antenna system be protected from damage
  33. due to a nearby lightning strike?
  34.  
  35.  A. Install a balun at the antenna feed point.
  36.  B. Install an RF choke in the feed line.
  37.  C. Ground all antennas when not in use.
  38.  D. Install a line fuse in the antenna wire.
  39.  
  40.  
  41. 2D 2.3   D
  42. How can Amateur Station equipment be protected from damage
  43. due to lightning striking the electrical wiring of the building?
  44.  
  45.  A. Use heavy insulation on the wiring.
  46.  B. Keep th equipment ON constantly.
  47.  C. Disconnect the ground system.
  48.  D. Disconnect all equipment after use, either by unplugging
  49.     or by using a main disconnect switch.
  50.  
  51.  
  52. 2D 3.1   B
  53. For proper protection from lightning strikes, what pieces
  54. of equipment should be grounded in an Amateur Station?
  55.  
  56.  A. The power supply primary.
  57.  B. All station equipment.
  58.  C. The feed line center conductors.
  59.  D. The AC power mains.
  60.  
  61.  
  62. 2D 3.2   A
  63. What is a convenient indoor grounding point
  64. for an Amateur Station?
  65.  
  66.  A. A metallic cold water pipe.
  67.  B. PVC plumbing.
  68.  C. A window screen.
  69.  D. A natural gas pipe.
  70.  
  71.  
  72. 2D 3.3   C
  73. To protect against electrical shock hazards, to what should
  74. the chassis of each piece of equipment in an
  75. Amateur Station be connected?
  76.  
  77.  A. Insulated shock mounts.
  78.  B. The antenna.
  79.  C. A good ground connection.
  80.  D. A circuit breaker.
  81.  
  82.  
  83. 2D 4.1   D
  84. When climbing an antenna tower, what type of safety 
  85. equipment should be worn?
  86.  
  87.  A. Grounding chain.
  88.  B. A reflective vest.
  89.  C. Long pants.
  90.  D. A saftey belt.
  91.  
  92.  
  93. 2D 4.2   A
  94. For safety purposes, how high should all portions of a
  95. horizontal wire antenna be located?
  96.  
  97.  A. High enough so that a person can not
  98.     touch them from the ground.
  99.  B. Higher than chest level.
  100.  C. Above knee level.
  101.  D. Above electrical lines.
  102.  
  103.  
  104. 2D 4.3   D
  105. While assisting another person working on an antenna
  106. tower, what type of safety equipment should a
  107. person on the ground wear?
  108.  
  109.  A. A reflective vest.
  110.  B. A safety belt.
  111.  C. A grounding chain.
  112.  D. A hard hat.
  113.  
  114.  
  115.   One (1) question must be from the following:
  116. ------------------------------------------------
  117.  
  118. 2D 5.1   B
  119. What is a likely indication that radio frequency interference
  120. to a receiver is caused by Front-End Overload?
  121.  
  122.  A. A low pass filter at the transmitter
  123.     reduces interference sharply.
  124.  B. The interference is independent of frequency.
  125.  C. A high pass filter at the receiver reduces
  126.     interference little or not at all.
  127.  D. Grounding the receiver makes the problem worse.
  128.  
  129.  
  130. 2D 5.2   C
  131. What is likely the problem when radio frequency interference
  132. occurs to a receiver regardless of frequency,
  133. while an Amateur Station is transmitting?
  134.  
  135.  A. Inadequate transmitter harmonic suppression.
  136.  B. Receiver VR tube discharge.
  137.  C. Receiver overload.
  138.  D. Incorrect antenna length.
  139.  
  140.  
  141. 2D 5.3   B
  142. What type of filter should be installed on a TV receiver
  143. as the first step in preventing Overload from
  144. an Amateur Radio Station Transmission?
  145.  
  146.  A. Low Pass.
  147.  B. High Pass.
  148.  C. Band Pass.
  149.  D. Notch.
  150.  
  151.  
  152. 2D 5.4   C
  153. What is meant by RECEIVER OVERLOAD?
  154.  
  155.  A. Interference caused by transmitter harmonics.
  156.  B. Interference caused by overcrowded band conditions.
  157.  C. Interference caused by strong signals from
  158.     a nearby transmitter.
  159.  D. Interference caused by turning the receiver
  160.     volume too high.
  161.  
  162.  
  163. 2D 6.1   A
  164. What is meant by HARMONIC RADIATION?
  165.  
  166.  A. Transmission of signals at whole number multiples
  167.     of the fundamental (desired) frequency.
  168.  B. Transmission of signals that include a
  169.     Superimposed 60 Hz. Hum.
  170.  C. Transmission of signals caused by sympathetic
  171.     vibrations from a nearby transmitter.
  172.  D. Transmission of signals to produce a stimulated
  173.     emission in the air to enhance skip propagation.
  174.  
  175.  
  176. 2D 6.2   A
  177. Why is harmonic radiation by an Amateur Station undesirable?
  178.  
  179.  A. It will cause interference to other stations and
  180.     may result in Out-Of-Band radiation.
  181.  B. It uses large amounts of electric power.
  182.  C. It will cause sympathetic vibrations
  183.     in nearby transmitters.
  184.  D. It will produce stimulated emission in the air
  185.     above the transmitter, thus causing Aurora.
  186.  
  187.  
  188. 2D 6.3   A
  189. What type of interference may radiate from a multiband
  190. antenna connected to an improperly tuned transmitter?
  191.  
  192.  A. Harmonic radiation.
  193.  B. Auroral distortion.
  194.  C. Parasitic radiation.
  195.  D. Intermodulation.
  196.  
  197.  
  198. 2D 6.4   C
  199. What is the purpose of shielding in a transmitter?
  200.  
  201.  A. It give the Low Pass filter structural stability.
  202.  B. It enhances the microphonic tendencies
  203.     of radiotelephone transmitters.
  204.  C. It prevents unwanted RF radiation.
  205.  D. It helps maintain a sufficiently high operating
  206.     temperature in circuit components.
  207.  
  208.  
  209. 2D 6.5   D
  210. What is the likely problem when interference is observed
  211. on only one or two channels of a TV receiver while
  212. an Amateur Station is transmitting?
  213.  
  214.  A. Excessive Low Pass filtering.
  215.  B. Sporadic E Deionization.
  216.  C. Receiver Front End Overload.
  217.  D. Harmonic Radiation.
  218.  
  219.  
  220. 2D 6.6   B
  221. What type of filter should be installed on an Amateur
  222. Transmitter as the first step in reducing harmonic radiation?
  223.  
  224.  A. Key Click filter.
  225.  B. Low Pass filter.
  226.  C. High Pass filter.
  227.  D. CW filter.
  228.  
  229.  
  230.   One (1) question must be from the following:
  231. ------------------------------------------------
  232.  
  233. 2D 7.1   B
  234. Why should the impedance of a transmitter final amplifier
  235. curcuit match the impedance of the antenna or feed line?
  236.  
  237.  A. To prevent sympathetic vibrations in
  238.     nearby radio equipment.
  239.  B. To obtain maximum power transfer to the antenna.
  240.  C. To help maintain sufficiently high operating
  241.     temperature in circuit components.
  242.  D. To create the maximum number of standing 
  243.     waves on the feed line.
  244.  
  245.  
  246. 2D 7.2   C
  247. What is the term for the measurement of the impedance match
  248. between a transmitter final amplifier circuit and the
  249. antenna or feed line?
  250.  
  251.  A. Voltage Flyback ratio.
  252.  B. Impedance Sine ratio.
  253.  C. Standing Wave ratio.
  254.  D. Current Overfeed ratio.
  255.  
  256.  
  257. 2D 7.3   A
  258. What accessory is used to measure RF power being reflected
  259. back down the feed line from the transmitter to the antenna?
  260.  
  261.  A. SWR Meter.
  262.  B. RF Tuner
  263.  C. S Meter.
  264.  D. Field Strength Meter
  265.  
  266.  
  267. 2D 7.4   C
  268. What accessory is often used to measure
  269. voltage standing wave ratio?
  270.  
  271.  A. Ohmmeter.
  272.  B. Ammeter.
  273.  C. SWR Bridge.
  274.  D. Current Bridge.
  275.  
  276.  
  277. 2D 7.5   D
  278. Where should a Standing Wave Ratio Bridge be connected to
  279. indicate the impedance match of a transmiter and an antenna?
  280.  
  281.  A. Between the antenna and matchbox.
  282.  B. Between the key and transmitter.
  283.  C. Between the mike and transmitter.
  284.  D. Between the transmitter and matchbox.
  285.  
  286.  
  287. 2D 7.6   B
  288. Coaxial Feed Line should be operated with
  289. what kind of Standing Wave Ratio?
  290.  
  291.  A. As high as possible.
  292.  B. As low as possible.
  293.  C. Standing Wave Ratio is not important.
  294.  D. Standing Wave Ratio cannot be measured in a Coaxial Cable.
  295.  
  296.  
  297. 2D 7.7   D
  298. If the Standing Wave Ratio Bridge reading is higher at
  299. 3700 kHz. than at 3750 kHz., what does this indicate
  300. about the antenna?
  301.  
  302.  A. Too long for optimal operation at 3700 kHz.
  303.  B. Broadbanded.
  304.  C. Good only for 37 meter operation.
  305.  D. Too short for optimal operation at 3700 kHz.
  306.  
  307.  
  308. 2D 7.8   A
  309. If the Standing Wave Ratio Bridge reading is lower at
  310. 3700 kHz. than at 3750 kHz., what does this indicate
  311. about the antenna?
  312.  
  313.  A. Too long for optimal operation at 3700 kHz.
  314.  B. Broadbanded.
  315.  C. Good only for 37 meter operation.
  316.  D. Too short for optimal operation at 3700 kHz.
  317.  
  318.  
  319. 2D 8.1   A
  320. What kind of Standing Wave Ratio Bridge reading may
  321. indicate poor electrical contact between parts
  322. of an antenna system?
  323.  
  324.  A. An erratic reading.
  325.  B. An unusually low reading.
  326.  C. No reading at all.
  327.  D. A negative reading.
  328.  
  329.  
  330. 2D 8.2   A
  331. High Standing Wave Ratio Bridge reaings measured from a
  332. Half-Wave Dipole antenna being feed by Coaxial Cable
  333. can be lowered by doing what to the antenna?
  334.  
  335.  A. Change the electrical length of the antenna.
  336.  B. Reduce the diameter of the antenna's radiating element.
  337.  C. Connect a short jumper wire across the 
  338.     antenna's center insulator.
  339.  D. Use a feed line having less loss per foot.
  340.  
  341.  
  342.   One (1) question must be from the following:
  343. ------------------------------------------------
  344.  
  345. 2D 9.1   B
  346. What precautions should you take
  347. when working with a 1270 MHz. Waveguide?
  348.  
  349.  A. Make sure that the RF Leakage Filters
  350.     are installed at both ends of the waveguide.
  351.  B. Never look into the open end of
  352.     the waveguide when RF is applied.
  353.  C. Minimize the Standing Wave Ratio
  354.     before you test the waveguide.
  355.  D. Never have both ends of the waveguide
  356.     open at once when RF is applied.
  357.  
  358.  
  359. 2D 9.2   A
  360. What precautions should you take when you mount
  361. a VHF or UHF antenna in a permanent location?
  362.  
  363.  A. Make sure that no one can be near
  364.     the antenna when you are transmitting.
  365.  B. Make sure the RF shield screens are in place.
  366.  C. Make sure the antenna is near the ground
  367.     to maximize the directional effects.
  368.  D. Make sure you install an RF Leakage
  369.     Filter at the antenna feed point.
  370.  
  371.  
  372. 2D 9.3   C
  373. What precautions should you take before removing
  374. the shielding on a VHF or UHF Power Amplifier?
  375.  
  376.  A. Make sure all RF screens are in place at the antenna.
  377.  B. Make sure the feedline is properly grounded.
  378.  C. Make sure the amplifier cannot be accidentally energized.
  379.  D. Make sure that the RF Leakage Filters are connected.
  380.  
  381.  
  382. 2D 9.4   A
  383. Why should you use only good quality, well constructed
  384. Coaxial Cable and connectors for a VHF or UHF antenna system?
  385.  
  386.  A. To minimize RF Leakage.
  387.  B. To reduce Parasitic Oscillations.
  388.  C. To maximize the directional characteristics of your antenna.
  389.  D. To maximize the Standing Wave Ratio of the antenna system.
  390.  
  391.  
  392. 2D 9.5   B
  393. Why should you be careful to position the antenna
  394. of your 220 MHz. Hand Held Transciever away
  395. from your head when you are transmitting?
  396.  
  397.  A. To take advantage of the directional effect.
  398.  B. To minimize RF exposure.
  399.  C. To use your body to reflect the signal, improving
  400.     the directional characteristics of the antenna.
  401.  D. To minimize static discharges.
  402.  
  403.  
  404. 2D 9.6   D
  405. How can you minimize RF Exposure when you
  406. are operating your 220 MHz. Hand Held Transciever.
  407.  
  408.  A. Position the antenna near the ground.
  409.  B. Use a shielded RF screen around your antenna.
  410.  C. Use a special short STUBBY DUCK antenna.
  411.  D. Position the antenna away from your head.
  412.  
  413.  
  414. 2D 9.7   D
  415. Why should you be careful to position the antenna
  416. of your 1270 MHz. Hand Held Transciever away
  417. from your head when you are transmitting?
  418.  
  419.  A. To take advantage of the directional effect.
  420.  B. To use your body to reflect the signal, improving
  421.     the directional characteristics of the antenna.
  422.  C. To minimize static discharges.
  423.  D. To minimize RF exposure.
  424.  
  425.  
  426. 2D 9.8   D
  427. How can you minimize RF Exposure when you
  428. are operating your 1270 MHz. Hand Held Transciever.
  429.  
  430.  A. Position the antenna near the ground.
  431.  B. Use a shielded RF screen around your antenna.
  432.  C. Use a special short STUBBY DUCK antenna.
  433.  D. Position the antenna away from your head.
  434.  
  435.  
  436. 2D 9.9   B
  437. How can you minimize RF Leakage
  438. from your VHF or UHF antenna system?
  439.  
  440.  A. Use open wire line for the antenna feed line.
  441.  B. Use only good quality, well constructed
  442.     Coaxial Cable and connectors.
  443.  C. Use special shielded AC line cords with all your equipment.
  444.  D. Use an RF Leakage Filter on the antenna feed line.
  445.  
  446.  
  447. 2D 9.10   B
  448. Why should you make sure your VHF or UHF amplifier
  449. cannot be energized before you open the amplifier enclosure.
  450.  
  451.  A. To minimize static discharge when you open the enclosure.
  452.  B. To minimize RF Exposure and prevent electrical shock.
  453.  C. To minimize the effectd of hand capacitance.
  454.  D. To prevent prevent exposure to
  455.     Cerenkov Radiation from the amplifier.
  456.  
  457.  
  458. 2D 9.11   B
  459. Why should you never look into a
  460. VHF or UHF waveguide when RF is applied?
  461.  
  462.  A. Because the fluorescent coating
  463.     inside the waveguide gets very bright.
  464.  B. Because exposure to VHF or UHF
  465.     RF Energy can be harmful to your eyes.
  466.  C. Because the waveguide might not be properly grounded.
  467.  D. Because the Cerenkov Effect may scatter RF energy.
  468.  
  469.  
  470. 2D 9.12   B
  471. Why should you be sure that your transmitter cannot
  472. be energized before you work on your VHF or UHF antennas?
  473.  
  474.  A. Because operating the transmitter when the
  475.     antennas are disconnected might harm the transmitter.
  476.  B. Because exposure to VHF or UHF RF Energy can be harmful.
  477.  C. Because if the transmitter is operated while
  478.     you are touching the antenna, the radiated
  479.     energy might be out of the Amateur Band.
  480.  D. Because accidental operation might blow a fuse.
  481.  
  482.  
  483. ------------------------------------------------
  484.  
  485. End of Subelement 2D.
  486.  
  487.