home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
The Mother of All Windows Books
/
CD-MOM.iso
/
cd_mom
/
drivers
/
netcard
/
depca
/
readme.txt
< prev
Wrap
Text File
|
1990-10-17
|
3KB
|
97 lines
;
; PROTOCOL.INI PARAMETERS
; for the DEC EtherWORKS (MC, LC, Turbo & DEPCA) Ethernet Adapters
;
;
; This document describes the PROTOCOL.INI keywords used for the
; DEC EtherWORKS NDIS MAC driver. The only parameter that must be
; specified is the "DriverName". Note that many of these parameters
; have default values (which are specified below). A parameter need
; not be specified in the PROTOCOL.INI file if its default value is
; satisfactory.
;
;DriverName
; units:[n/a]
; range:[DEPCA$]
; default:[DEPCA$]
;
; This parameter's value must be DEPCA$, it identifies the network
; device driver.
;
; The following entries are optional under the [DEPCA] section.
;
;MaxMulticast
; units:[integer]
; range:[1-256]
; default:[8]
;
; This specifies the maximum number of multicast addresses that can
; be in effect simultaneously. (NOTE that there's no 's' on the end of
; this keyword.)
;
;MaxTransmits
; units:[integer]
; range:[0-256]
; default:[16]
;
; This specifies the number of "TransmitChain"s that the MAC driver
; guarantees to accept without giving an "OUT_OF_RESOURCE" response.
;
; The following parameters ONLY need to be set if your DEC EtherWORKS
; adapter (MC, LC, Turbo or DEPCA) does not contain a diagnostic or
; remote boot ROM chip.
;
;AdapterName
; units:[n/a]
; range:[DEPCA,DE100,DE200,DE210]
; default:[n/a]
;
; This specifies the name of the ethernet adapter.
;
; values adapter
; ------------ -------------------
; DEPCA DEPCA
; DE100 DEC EtherWORKS LC
; DE200 DEC EtherWORKS Turbo
; DE210 DEC EtherWORKS MC
;
;RamAddress
; units:[hex]
; range:[C000,C800,D000,D800,E000,E800]
; default:[n/a]
;
; This specifies the physical base address in the PC memory address
; space of the "window" through which the adapter's RAM will be
; referenced. This parameter's value must agree with the jumpered
; configuration of the adapter. Not required for DEC EtherWORKS MC
; Adapter.
;
;Interrupt
; units:[integer]
; range:[2-15]
; default:[n/a]
;
; This specifies the IRQ level that will be used by the adapter-to-PC
; interrupt. Its value must agree with the jumpered configuration of
; the adapter. Not required for DEC EtherWORKS MC Adapter.
;
; values adapter
; ------------ -------------------
; 2,3,4,5,7 DEPCA
; 2,3,4,5,7 DEC EtherWORKS LC
; 5,9,10,11,15 DEC EtherWORKS Turbo
; 5,9,10,11 DEC EtherWORKS MC
;
;
; Following is an example PROTOCOL.INI fragment for a DEC EtherWORKS
; Turbo adapter with no diagnostic or remote boot ROM chip:
[DEPCA_NIF]
DriverName = DEPCA$
MaxMulticast = 12
MaxTransmits = 32
AdapterName = DE200
RamAddress = 0xD000
Interrupt = 5