home *** CD-ROM | disk | FTP | other *** search
/ Media Share 9 / MEDIASHARE_09.ISO / hamradio / kenwood1.zip / TH2545.MOD < prev    next >
Text File  |  1990-02-08  |  15KB  |  326 lines

  1.  
  2.         In the past, I posted some mods for the Kenwood TH-X5AT
  3. series of HTs.  My previous posting had some minor errors, and left
  4. some questions unanswered.  Yesterday, I helped a friend modify his
  5. TH-45AT, and some of these questions were answered.  This posting
  6. will clear up the problems in the previous posting, as well as contain
  7. all of the important information from the previous posting.  You may
  8. delete your previous copy of this information, and replace it with
  9. this one.
  10.  
  11. ---------------------------------------------------------------------
  12.  
  13.         Copyright (C) Notice: Some people have been taking
  14. information posted to this network, publishing it, and selling it.
  15. Not only is this immoral, it is also illegal.  You may not do this.
  16. I give everybody the right to copy this material, and give it to
  17. others.  You must not sell it.  You may NOT include this information
  18. in a newsletter or compendium that you charge for, but you may incude
  19. it in a free newsletter or compendium.  You may NOT distribute this
  20. information on a computer bulletin board system that users are
  21. charged any fees for, but you may distribute this information on a
  22. computer bulletin board system if you provide the service free of
  23. charge.  You must not alter the information provided here in any way,
  24. including removing this copyright notice and/or removing the authors'
  25. name and/or e-mail address at the end of this message.
  26.  
  27. ---------------------------------------------------------------------
  28.  
  29.         Here are some mods for the TH-25AT and the TH-45AT.  Please
  30. note that I do not encourage transmitting on a frequency for which
  31. you do not have a license, nor do I encourage transmitting in the
  32. United States on a non-amateur frequency with equipment that has not
  33. been FCC type accepted.  This is illegal in the United States, even if
  34. you have a license to transmit on the given non-amateur frequency.
  35.  
  36.         First let me recommend that you buy the service manuals for
  37. these radios.  The service manual is not expensive (about $15 I
  38. think) and it will greatly help you in performing these mods.
  39.  
  40.         Before performing any of these modifications, make sure you
  41. know what's in your memories, because they will be lost.
  42.  
  43. ---------------------------------------------------------------------
  44.  
  45.         Look at the schematic for your radio.  In the lower left hand
  46. corner is an IC labled IC2.  This is an ASIC microprocessor.  At the
  47. lower right hand corner of this uP are several diodes and pull-up or
  48. pull-down resistors.  They are D4, D3, R19, R18, R28, R20, R21, R22,
  49. R25, R26, and a couple of resistors that are not even on the
  50. schematic that attach to B2 (pin 51 on IC2) and B3 (pin 50 on IC2).
  51. The TH-45AT schematic shows R23 on the ASIC uP pin B2.  Another
  52. important resistor is R27; on the schematic it is located next to the
  53. frequency selection switch EN1 above IC2.  A less important resistor
  54. (for modification purposes) is R36; on the schematic it is located to
  55. the right of IC2 in line with the top edge of IC2.
  56.  
  57. The schematic for the TH-25AT shows:
  58.  
  59.                          R18-R21  R25  R26,27  R28  R36
  60. TH-25A    M,M2      -12     O      X      X     X    X
  61. TH-25A    M3,M4,X   -23     O      X      X     O    X
  62. TH-25AT   K         -11     O      O      X     X    X
  63. TH-25AT   M,M2      -12     O      X      X     X    X
  64. TH-25E    T         -52     X      X      O     O    O
  65. TH-25E    W         -62     X      O      O     O    O
  66.  
  67. And the schematic for the TH-45AT shows:
  68.  
  69.                          R19-R21  R22  R23  R25  R26,27  R28  R36
  70. TH-45A    M1,M2,X   -21     O      O    O    X      X     O    X
  71. TH-45A    M3,M4     -22     O      X    O    X      X     X    X
  72. TH-45AT   K         -10     O      X    O    X      X     O    X
  73. TH-45AT   M1,M2     -21     O      O    O    X      X     O    X
  74. TH-45AT   M3,M4     -22     O      X    O    X      X     X    X
  75. TH-45E    T         -51     X      O    X    X      O     X    O
  76. TH-45E    W         -61     X      O    X    O      O     O    O
  77.  
  78. where O means USED, and X means NOT USED.
  79.  
  80. Some of the above codes are:
  81. K     USA
  82. T     England
  83. X     Australia
  84. M     Other Areas
  85.  
  86.         These components are found on the flexible circuit board
  87. under the display.  To get to them, take the radio apart.
  88.  
  89. ---------------------------------------------------------------------
  90.  
  91. (1)     Only 8 screws must be removed from the case to take the radio
  92. apart; these are the 4 screws that hold the battery clip on, the 2
  93. screws on the back half of the case near the PTT switch, the screw on
  94. the back of the case under (and in line with) the BNC connector, and
  95. the screw on the back half of the case adjacent to the external
  96. speaker jack.
  97.  
  98. (2)     After removing these 8 screws, remove the front half of the
  99. case from the back half.  You may unconnect the blue plug from the
  100. touch tone circuitry on the front half of the case to make further
  101. work on the radio more convenient, but it is not necessary.
  102.  
  103. (3)     Place the radio back side down with the antenna away from
  104. you.  Now, unsolder the two grounding wires from the plate which
  105. covers much of the radio's circuitry.  These wires are near the top
  106. of the plate and will be quite obvious.
  107.  
  108. (4)     Next, remove the 7 screws that hold this plate on.  5 of the
  109. screws for this plate are up on top and are quite obvious; the other
  110. 2 are at the bottom of the plate, and may be hidden by your CTCSS
  111. unit.  Remove the plate.
  112.  
  113. (5)     Remove the red plug with about 7 wires that connects just
  114. under the volume and squelch switch.
  115.  
  116. (6)     Remove the screw that holds the PTT/LAMP/MONI switch
  117. assembly; this screw is on the left side of the radio just under the
  118. PTT switch.
  119.  
  120. (7)     Remove the two screws that hold the top assembly to the back
  121. case of the radio; these two screws are on either side of the orange
  122. flexible circuit board coming from the top assembly and plugging into
  123. the back case of the radio.  You may need to use a screwdriver or
  124. stick to move the orange flexible circuit board out of the way in
  125. order to see these final two screws.
  126.  
  127. (8)     Unplug the orange flexible circuit board from the back case.
  128. At this point, the whole top assembly should come free quite easily.
  129. The BNC connector will stay attached to the back case, and the whole
  130. top assembly will come up over it.
  131.  
  132. (9)     Unfold the flexible circuit board and unfold it so that the
  133. components are accesable.  One of the fold-out parts of the flexible
  134. board will look something like this: (the component side is shown up)
  135.  
  136. +----------------+
  137. | R R R R D3 R R |
  138. | 2 2 2 2    7 2 |      The O's are very large solder pads.
  139. | 5 4 3 2      1 |
  140. |                |
  141. | R  O      O R20|      Not all components will be installed on your
  142. | 2  O      O R19|      circuit board.
  143. | 6  O      O R18|
  144. |    O      O R28|
  145. |                |      D3 & D4 are two diodes in a three terminal
  146. |              R |      package.  The anodes of the diodes are in
  147. |           D4 6 |      common.
  148. |        +-------+
  149. |        |
  150. |        |
  151.  
  152. The fold out board is actually square, but with only characters for
  153. graphics, I couldn't draw it that way.  It comes out reasonably
  154. square on a printer with 10 characters/inch and 6 lines/inch.
  155.  
  156. On both radios, R27 is located to the right of the four blue buttons
  157. on the back of the radio (M CTCSS SHIFT REV).  You should be able to
  158. see this on the back of the now removed top assembly.
  159.  
  160. On both radios, R36 is for the European tone burst to "whistle up"
  161. repeaters.  R36 is located on another portion of the flexible circuit
  162. board, closest to pin 1 of IC2.  IC2 is the IC closest to the
  163. portion of the flexible circuit board shown above.  Most users will
  164. not want to change R36.
  165.  
  166. ---------------------------------------------------------------------
  167.  
  168.         Here is the function of the diodes and pull up or pull down
  169. resistors (for both the TH-25AT and the TH-45AT unless otherwise
  170. specified):
  171.  
  172. D4      selects the display type.
  173.         installed:      channel display
  174.         removed:        normal frequency display
  175.  
  176.         You probably don't want to install this.
  177.  
  178.         R6 is the pullup resistor for D4.  Do not remove it, so that
  179.         if D4 is removed, pin 44 of IC2 will be properly pulled up.
  180.  
  181. D3      selects VHF or UHF.
  182.         installed:      VHF
  183.         removed:        UHF
  184.  
  185.         You definitely don't want to change this!
  186.  
  187.         R7 is the pullup resistor for D3.  Do not remove it, so that
  188.         if D3 is removed, pin 45 of IC2 will be properly pulled up.
  189.  
  190. R25     selects automatic offset selection.
  191.         installed:      automatic offset selection enabled.
  192.         removed:        automatic offset selection disabled.
  193.  
  194.         R25 seems to have no effect on the TH-45AT.
  195.  
  196. R23,27  frequency selection step size.
  197.  
  198.         Frequency selection step sizes is only known for TH-45AT.
  199.  
  200.         R23     R27     frequency selection step sizes:
  201.         ---     ---     --------- --------- ---- ------
  202.         out     out      5 and 10   kHz
  203.         in      out      5 and 25   kHz (TH-45AT default)
  204.         out     in       5 and 12.5 kHz (author's preference)
  205.         in      in      10 and 20   kHz
  206.  
  207.         R23 probably has no effect on the TH-25AT.  I never checked.
  208.         I was quite satisfied with the 5 and 10 kHz step sizes for
  209.         the TH-25AT.  I never tried changing R27 to see what would
  210.         happen.
  211.  
  212. R24     ? something with the CTCSS tone ?
  213.         installed:      When a TX offset is selected, the CTCSS tone
  214.                         is always transmitted.  The TONE button does
  215.                         not work correctly.  When the TONE button is
  216.                         depressed, the display goes to 430.000 c, and
  217.                         nothing seems to work.  (A "c" is displayed
  218.                         in the channel number position.)  The action
  219.                         of the TH-25AT is unknown.
  220.         removed:        CTCSS tone selection works correctly.  Both
  221.                         the TH-25AT and the TH-45AT are delivered
  222.                         this way.
  223.  
  224.         You probably don't want to install this.
  225.  
  226. R19     function unknown.
  227.         R19 is not installed in the European version.
  228.  
  229. R20     function unknown.
  230.         R20 is not installed in the European version.
  231.  
  232. R21     function unknown.
  233.         R21 is not installed in the European version.
  234.  
  235.         R19, R20, and R21 are all in parallel.  Thus, if any of them
  236.         is installed, it is like all of them are installed.
  237.  
  238. R26     function unknown.
  239.         R26 is installed in the European version.
  240.  
  241. On the TH-25AT:
  242.  
  243. R22,28  select RX and TX frequency range.
  244.  
  245.         R22     R28     RX range        TX range
  246.         ---     ---     -- -----        -- -----
  247.         in      out     144-148         141-163         (USA default)
  248.         in      in      144-148         144-148
  249.         out     out     100-200         100-200         (only where
  250.                                                         your PLL
  251.                                                         locks up.)
  252.         out     in      142-151         ???-???
  253.  
  254. R18     exact function unknown.
  255.         installed:      as delivered in USA.
  256.         removed:        TX disabled from 146-148.
  257.  
  258.         The RX and TX frequency range based on R22 and R28 are
  259.         unknown if R18 is removed.
  260.  
  261. On the TH-45AT:
  262.  
  263. R18,28  select RX and TX frequency range.
  264.  
  265.         R18     R28     RX range        TX range
  266.         ---     ---     -- -----        -- -----
  267.         in      out     440-450         440-450
  268.         in      in      438-450         438-450         (USA default)
  269.         out     out     200-500         200-500         (only where
  270.                                                         your PLL
  271.                                                         locks up.)
  272.         out     in      215-230         215-230?        (PLL won't
  273.                                                         lock up.)
  274.  
  275. R22     TX offset selection
  276.         installed:      1.6 MHz offset (perhaps for 220, or Europe)
  277.         removed:        5   MHz offset (USA default)
  278.  
  279. ---------------------------------------------------------------------
  280.  
  281.         PLL adjustment
  282.         --- ----------
  283.  
  284.         I have found a quick and easy way to retune your PLL (in the
  285. TH45-AT) with a minimum of test equipment.  All you need is a scope
  286. and a small tuning tool.  First, take off the battery pack holder
  287. plate.  Then, remove the silvery sticker covering the tuning pot
  288. access holes.  If the radio is positioned on its back, with the top
  289. folded over so that the touch tone pad is also facing down, the test
  290. point you want (TP1) is on the bottom half of the radio, near the
  291. center (left to right), and close to the battery; the tuning pot you
  292. want (TC1) is on the bottom, and closest to the PTT switch.  Under no
  293. circumstances change the tuning of TC51.  This is used to calibrate
  294. the output of the radio with the display the radio is giving; you
  295. don't want to mess with it.  Once again, the Service Manual makes it
  296. very clear where these points are, if you are having trouble with my
  297. descriptions.  On with retuning the PLL.  With the radio on, and
  298. receiving, monitor the voltage and the waveform on test point TC1.
  299. Tune the radio DOWNWARDS in frequency until the PLL unlocks.  Note
  300. that the radio will beep when this happens, and the waveform on TP1
  301. will change.  Tune the radio about 1 MHz higher so that the PLL locks
  302. up again, and note the voltage on the testpoint, TP1.  Now, tune the
  303. radio to the LOWEST frequency that you want to be able to receive.
  304. (Be very careful when you adjust TC1.  If you are not careful, you
  305. could break TC1 loose.  This will cause your radio to have
  306. microphonics.  Mechanical vibrations will change the value of this
  307. capacitor, and thus change the tuning on the PLL.  If you encounter
  308. this problem, you can repair it by dripping wax through the small
  309. hole onto TC1, or by replacing TC1.  It is of course better not to
  310. break it in the first place.)  Adjust TC1 until the voltage on the
  311. test point TP1 is the same as what was noted earlier.  Button the
  312. radio back up, and you're done. You will not be able to tune the PLL
  313. to any range you want.  There are limits.  On my radio, I have been
  314. able to retune the radio so that I can recieve from 439.2-468.6 MHz
  315. with a set of batteries fresh out of the charger.  The tuning range
  316. will probably diminish as the battery voltage decreases.  I have not
  317. retuned the PLL on my 2m HT, but I'd imagine the same technique will
  318. prove fruitful.
  319.  
  320. ---------------------------------------------------------------------
  321.  
  322. In the rare case that original ideas   Kenneth J. Hendrickson    N8DGN
  323. are found here, I am responsible.      Owen W328, E. Lansing, MI 48825
  324. Internet: kjh@pollux.usc.edu           UUCP: ...!uunet!pollux!kjh
  325.  
  326.