Media Share 9/MEDIASHARE_09.ISO/hamradio/docs106.zip/INTRONOS.ZIP/INTRONOS.TXT

Text File | 1992-04-24 | 60KB | 1,366 lines

        Getting Started with TCP/IP on Packet Radio


        by John Ackermann, AG9V
        Miami Valley FM Association
        Dayton, Ohio





        20 April 1992








    Copyright 1992 by John R. Ackermann, Jr.
    This document may be freely distributed in unaltered form for non-
    commercial use only, provided this copyright notice is included.

                *** Introduction ***

    This document is intended to help hams with some experience in
    packet radio get started with the TCP/IP software written by KA9Q
    and others.  It is not intended to take the place of the software's
    reference manual, but rather to provide a quick-and-dirty
    introduction to the capabilities of TCP/IP and the mysteries of
    installing and using the software.

    There are several different versions of the KA9Q software floating
    around.  It was originally written for MS-DOS computers, but has
    been ported to Macintosh, Amiga, Atari and UNIX systems.  The
    original program was called "NET" and its last formal version was
    issued in April, 1989.  If someone talks about "890421.1 NET,"
    that's what they're referring to.

    Since 1989, work has concentrated on a rewritten program called
    "NOS" (for Network Operating System, though confusingly the
    executable program for PCs is usually still called "NET.EXE").  NOS
    offers many new features that make using TCP/IP much more
    effective; you should use it instead of NET.  However, NOS is a
    growing and changing creature; since there are several different
    versions, and they are being updated rapidly, I can't tell you
    precisely where to find the latest, greatest version.  Your best bet
    is to check with a local user.  If that doesn't work, there are
    several telephone BBS systems that carry various flavors of NOS:

        N8EMR's Ham BBS    [phone]
        ChowdaNet    [phone]
        WB3FFV        [phone]

    The version I'm using, and which is reflected in this document, is
    PA0GRI's adaptation of NOS version 061891, as modified and
    distributed by N1BEE and available as "GRINOS" from the
    ChowdaNet BBS.  I try not to dwell on features that are specific to
    this version, but if something I say doesn't seem to match your
    software, that's probably why.

    A last note before plunging in -- I said it before, and I'll say it
    again:  this document barely scratches the surface of NOS.  Nearly
    every command described here has options or parameters that I'm
    ignoring.  My goal is to give you a feel for what TCP/IP does, and
    to get you on the air with NOS; to get beyond the novice stage
    you need to look at the reference manual and experiment with the
    software.  Appendix A includes a list of organizations and
    individuals that can provide further information about TCP/IP and
    amateur radio.

            *** TCP/IP and Ham Radio ***

    TCP/IP is a set of communication protocols that have become a
    standard in the computer networking world.  It is designed to link
    different kinds of computer systems together over dissimilar
    networks.  TCP/IP software runs on nearly every kind of computer
    available, from IBM mainframes to PCs, Macs, Amigas, and Ataris.
    The KA9Q software (from now on, I'll call it "NOS") is special
    because it includes the features necessary to run TCP/IP over ham
    packet radio.

    The TCP/IP protocol suite allows different kinds of computers to
    talk to one another across networks.  The services it provides
    include terminal sessions, file transfer, electronic mail, and data
    routing services.  Computers running TCP/IP (referred to as
    "hosts") can run some or all of these applications simultaneously;
    it's entirely possible to sit at a PC computer running NOS and carry
    on a keyboard-to-keyboard chat with one station, while another
    retrieves a file from your hard disk and you send electronic mail to
    a third.

    It's also comforting to know that when you run TCP/IP, you don't
    give up the ability to carry on normal packet communications.  You
    can use NOS just like a terminal program to establish connections
    with your local BBS or to chat with friends who don't run NOS
    (yet).

    If you've looked at the size of the NOS documentation, you're
    probably asking yourself what the benefit is of mastering this fairly
    complex stuff.  Well, NOS has several features that improve on
    regular packet radio.  It has much more sophisticated file transfer
    and electronic mail capabilities than our present PBBS systems
    (and it's possible to feed PBBS messages into NOS in a way that
    makes it much easier to use them).  It supports multiple
    simultaneous connections.  It has new and better transport
    methods that improve the reliability and throughput of slow and
    congested channels.

    NOS also has the ability to route transmissions to distant stations
    without the user needing to know every hop along the way; all
    you need to do is get your data to a "gateway" station that knows
    how to move it one hop closer to its destination.  New work being
    done with NOS promises dynamic routing that automatically
    adjusts to changes in the network.

    And, since it is directly adapted from the de facto standard system
    of interconnecting computers, NOS offers the possibility of
    sophisticated services far beyond anything available on regular
    packet radio.  For example, in some areas ham TCP/IP users can
    log into multi-user UNIX computer systems and run applications as
    if they were directly connected to those machines.

                *** What is TCP/IP? ***

    As mentioned above, TCP/IP is actually a set of protocols for the
    transfer of data across networks of computers.  Two of these
    protocols underlie most of the others, and they give the set its
    popular name:

    TCP    Transport Control Protocol, a "reliable stream service"
        (which is a fancy way of saying it makes sure that all the
        data sent to a remote host actually gets there), and

    IP    Internet Protocol, which sets the basic rules for
        formatting packets of data to go out over a network.
        TCP rides on top of IP.

    Now that you finally know what "TCP/IP" stands for, there are a
    few concepts that are critical because they address a basic
    problem in any communications system -- identifying the parties to
    the conversation.  Simply using our ham callsigns to address
    TCP/IP packets doesn't work for two reasons.  First, the protocols
    work across many different networks, and have to have a
    consistent address scheme.  Second, and as important, ham
    callsigns don't contain enough information to allow TCP/IP's
    sophisticated routing mechanisms to work.


    Names and Addresses

    The first important concept is the "IP Address."  Since these
    protocols are used on lots of different computers, it is necessary to
    use an addressing system that works with all of them, that
    provides adequate routing information, and that doesn't take up a
    lot of space.  The answer is to build addresses out of a four byte
    sequence of integers, with each byte providing information about
    the network and subnetwork(s) to which a host belongs.

    IP addresses are "hierarchical" because the four bytes have
    decreasing significance from left to right.  By looking at the
    leftmost byte(s) we can learn how to route a transmission to the
    host represented by the rightmost byte(s).  We usually print these
    addresses using the numeric value of each byte, separated by a
    period, such as [44.70.12.34].  This is known as "dotted
    notation."  The square brackets aren't strictly necessary, but they
    are convenient to set off IP addresses; I'll use them that way in
    this document.

    I won't go into all the semantics of hierarchical addressing here,
    but as an example the address [44.70.12.34] breaks down as:

        44.    The network assigned to amateur radio TCP/IP.
        70.    The subnetwork for Ohio.
        12.    The Dayton/Cincinnati subnetwork.
        34    A specific system address within that area.

    IP addresses are assigned by coordinators who derive their
    authority from a central registry.  The coordinator for the ham
    radio net is Brian Kantor, WB6CYT.  He has delegated authority to
    assign addresses to various state and national coordinators.  The
    folks in Appendix A can help you find your local coordinator.

    The second important concept is the "hostname."  Obviously, IP
    addresses aren't very intuitive.  English-like hostnames make
    remembering addresses much easier, and TCP/IP programs,
    including NOS, have means (discussed below) to map between IP
    addresses and hostnames.  A "host" is any computer running
    TCP/IP; even when you're using services from another computer,
    your system is still a host.  When we talk about a "remote host,"
    we're talking about a machine that you're communicating with via
    TCP/IP.

    The convention in ham radio TCP/IP is to use your callsign as your
    hostname.  To help reduce confusion, we usually print hostnames
    in lower case, and callsigns in capital letters -- my hostname is
    "ag9v," and my call is "AG9V" (though NOS isn't case sensitive
    and won't care if you don't do it this way).

    Closely related to the hostname is the "domain name."  A
    "domain" is a group of machines that are logically (though not
    necessarily physically) connected together.  Domain names are like
    IP addresses; periods separate parts of the name, with each part
    representing a different level in the domain hierarchy.  But the
    domain name is ordered in reverse -- its highest-level portion is at
    the right, the opposite of IP addresses.

    The ham network's domain is "ampr.org"; "org" (short for
    "organizations") is the top level domain, and "ampr" (for AMateur
    Packet Radio) is the second level domain, containing all ham
    TCP/IP hosts.

    When you combine a hostname with a domain name, you get
    something like "ag9v.ampr.org."  This is called a "Fully Qualified
    Domain Name" ("FQDN" -- knowing this acronym allows you to
    sound like a real expert).  If a host has multiple users, we can add
    the user's login name at the beginning of the address, separated
    from the FQDN by a "@" character.  This combination is
    commonly known as an "Internet address" (the "Internet" is the
    general term for all the TCP/IP hosts that are interconnected) and
    is the address form used for most electronic mail in the real world.
    For example, if there is a user "jra" at ag9v, "[e-mail]"
    would be that user's full Internet address.

    There's one last twist.  Some services (such as Domain Name
    Service, discussed below) need to know whether an address they
    are processing is in fact an FQDN.  To do so, they look for a
    trailing period at the end of the domain name.  Some versions of
    NOS ignore this issue, but the PA0GRI versions (such as GRINOS)
    insist that you "anchor" all domain names with a period at the end
    of the name.  In other words, GRINOS will barf if you issue the
    command "hostname ag9v.ampr.org" but "hostname
    ag9v.ampr.org." will make it happy.

    This may seem like an overly complicated scheme to simply allow
    two hams to talk to each other, but we use it because the ham
    radio TCP/IP network can be tied to the worldwide TCP/IP network
    in a number of different ways, and using the full set of TCP/IP
    address conventions makes it possible for traffic to flow between
    the ham network and the real world.

    Leaving aside legal issues about third-party traffic, there's no
    reason, for example, why electronic mail can't be automatically
    routed through a "gateway" (a computer that interconnects two or
    more networks) between a ham TCP/IP user and a non-ham who
    has access to the Internet.  In fact, this service already exists in
    some areas.

    The good news is that for traffic within the ham network, we only
    need to worry about hostnames, and NOS's "domain suffix"
    command will take care of adding the "ampr.org" extension for us;
    we only need to deal with the full details of addressing if we want
    to go outside the ham radio network.


    TCP/IP Services

    Now that we have those boring basics out of the way, the
    protocols that use TCP/IP to provide real, useful services include:

    TELNET    The terminal emulation program.  In "real" networks,
        telnet lets a user at one host remotely access a remote
        host, just as if he was on a terminal directly connected
        to that computer.  In NOS, the telnet function usually
        connects you to a remote host's mailbox, which acts
        very much like a personal PBBS.  The NOS telnet
        command does allow you to remotely login to a host that
        supports that function; in some areas UNIX computers
        connected to the ham TCP/IP network provide that
        service.

    FTP    File Transfer Protocol.  A means of transferring both
        ASCII (text) and binary (program, data, or compressed)
        files between hosts.

    SMTP    Simple Mail Transfer Protocol.  A (mostly) invisible way
        of moving electronic mail from one host to another.  If
        you create a message on your computer (using the BM
        program, discussed below), SMTP will automatically
        attempt to transfer it to the destination computer.

    POP    Post Office Protocol.  SMTP is neat, but it's really
        designed to work with hosts that are available full time.
        Most ham TCP/IP stations aren't.  POP is designed for
        them; it allows incoming mail to be stored at a host that
        acts as a "mail server;" when you come on the air, your
        system automatically asks the server to send you your
        mail.

    PING    Packet InterNet Groper.  A diagnostic that sends a packet
        to a specified host; if the host is accessible to you and
        on the air, it responds with another packet.  PING tells
        you how long the round trip took.

    FINGER    A way of finding out information about the users at a
        host.  The finger command can simply list all the users at
        a host, or spit out information (like the "brag tape" of
        RTTY days) about a specific user.

    ARP    Address Resolution Protocol.  IP addresses need to be
        matched with the correct hardware address (in our case,
        ham callsign) to allow packets to be sent to their
        destination -- NOS doesn't know what callsign goes with
        a given IP address.  ARP does this by sending out a
        broadcast message when it needs to know the callsign
        that matches an address.  The remote host (if it's on the
        air) will answer and provide its hardware address.

    DNS    Domain Name Service.  Remembering IP addresses isn't
        easy.  NOS can use a file called "DOMAIN.TXT" to
        contain mappings between hostnames and IP addresses,
        but that means you need to know the hostname and
        address of any station you want to contact.
        Alternatively, a remote host may agree to serve as a
        "domain name server" that NOS can query when it needs
        to know the address of a host.  Not all areas have a
        name server available to the ham community, but in
        those that do, life is a lot easier.

                *** Installing NOS ***

    Frankly, there's no completely painless way to get NOS running on
    your computer.  NOS is somewhat picky about the directories used
    for its files, and there are a number of custom parameters that you
    must set to teach the program about your environment and your
    network.  Those parameters are contained in a configuration file
    that most versions of NOS call "AUTOEXEC.NET" (PA0GRI
    versions use "AUTOEXEC.NOS;" our references to
    "AUTOEXEC.NET" mean whichever name is appropriate).


    Files and Directories

    You should create the following directories on your disk (NOS can
    work from either a hard disk or a floppy; it's getting big enough,
    though, that working from a 360K floppy can be tough):

    \spool                (holds NOS' working files)
    \spool\help            (help files for the mbox)
    \spool\mail            (mail messages go here)
    \spool\mqueue            (mail workfiles)
    \spool\rqueue            (incoming mail workfiles)
    \finger                (home for finger info files)
    \public                (file uploads/downloads)

    These files need to go in the root directory of your default disk (it
    is possible to configure NOS to look for these files in other than
    the root directory; see the reference manual for details):

    AUTOEXEC.NET            (the NOS configuration file)
    FTPUSERS            (user ftp/mbox access)
    DOMAIN.TXT            (hostnames)
    BM.RC                (mail program configuration)
    ALIAS                (used by smtp and BM)

    NOS uses two executable files.  These can be installed anywhere
    on your file path:

    NET.EXE, NOS.EXE, or GRINOS.EXE    (main executable)
    BM.EXE                (mailer program)


    Setting up AUTOEXEC.NET

    Once the directories are created and the files copied, you need to
    edit the AUTOEXEC.NET file with a text editor to customize it.  A
    sample file is included as Appendix B.  Some of the things you'll
    have to put in the file are:

    Your hostname (usually your callsign in lower case):
        hostname ag9v.ampr.org.

    Your IP address:
        IP address [44.70.12.34]

    Your callsign (optionally including an SSID; local customs vary on
    this):
        ax25 mycall AG9V

    "attach" commands to tell NOS how to talk to your hardware.
    These can get quite hairy; Appendix C has the details.  For a TNC
    on COM 1 at 4800 baud serial port speed, use:
        attach asy 0x3f8 4 ax25 ax0 1024 256 4800

    The "ax0" in the middle of the command is the "interface" name --
    you use it to identify this port to NOS when you set up routing
    commands and the like.  You can use any (short) name you'd like,
    but the convention for COM ports is to use ax0, ax1, etc.

    At least one routing command.  NOS needs to know where to
    send packets.  A default route that sends all packets out the ax0
    interface is:
        route add default ax0

    If you have a gateway for packets going outside the local area,
    include a route like:
        route add [44.70.13.0]/24 ax0 ag9v

    This command would route packets addressed to any host with
    "44.70.13" as the first three bytes of its address out the ax0
    interface to ag9v, which presumably knows how to get these
    packets to their destination.  The "/24" means that the first 24 bits
    (three bytes) of the address are significant; NOS will ignore the
    last byte when making routing decisions.

    If you have a domain name server, add a command near the
    beginning of your configuration file identifying its IP address:
        domain addserver [44.70.12.34]

    If you have a local mail server that knows how to route messages
    outside the area (see the discussion of electronic mail, below), add
    a command identifying it:
        smtp gateway [44.70.12.34]


    Storing Name/Address Matches in DOMAIN.TXT

    If you don't have a local domain name server (DNS), you'll need to
    create "DOMAIN.TXT" in the root directory, with one entry for
    every hostname you want to communicate with.  Appendix D
    shows how to set up this file.  If you don't have an entry for a
    host in the file (or the name server doesn't know about it), you
    can use the IP address instead of the hostname in NOS
    commands.

    If you're using DNS, NOS will save the hostname/address matches
    it gets from the server in DOMAIN.TXT, so you'll find that file
    existing (and growing) even if you didn't create it.

    Giving the Finger

    If you want users to be able to learn about your station with the
    finger command, you need to create a text file in the \finger
    directory called <hostname>.txt (by the way, when we use angle
    brackets like this, it means this is a value you'll need to insert
    yourself -- minus the angles -- based on your own configuration).
    You can use any ASCII text editor to create the file; it should
    contain basic info about your system.  Don't go overboard... one
    screen of text is plenty.

    You can also create additional files with information about specific
    aspects of your system.  For example, you might have a list of the
    files available for downloading on your system in a finger file called
    "filelist.txt."  A remote host who issues the command "finger
    filelist@<myhost>" will get that list.


    Some Boring but Necessary Technical Stuff

    Before we move on to the good stuff about how to make NOS do
    magic, we need to talk about three related commands that you
    may need to tweak depending on local custom and the quality of
    the RF paths you're using.  Just as regular AX.25 uses the
    "paclen" command to limit the size of packets, TCP/IP has
    parameters defining how much data is moved in one chunk.  In
    theory, the larger the datagram (TCP/IP's term for a single block of
    data), the higher the efficiency, because the protocol headers add
    a fixed amount of overhead; in larger datagrams the overhead is a
    smaller percentage of the total data sent.

    However, some networks (such as NetRom) can't handle large
    datagrams in one piece.  More importantly, the larger the
    datagram, the longer it takes to transmit, and on a busy or flaky
    path, the greater the likelihood that something will corrupt it along
    the way.  And, it takes longer to resend a large packet than a
    small one, so the cost of retries is greater.  Because of these
    factors, a fast network with clear channels and solid paths can get
    away with sending much larger datagrams than a slow, unreliable
    one.

    NOS provides three parameters that deal with datagram sizes.  The
    most important one is the "mtu" (the sixth value in the "attach
    asy" command described above).  It is similar to paclen; it sets the
    largest packet, including any headers, that can be sent on an
    interface.  Datagrams larger than the mtu are fragmented into
    multiple pieces, which seriously reduces efficiency.  Each interface
    has its own mtu, set as part of its attach command.

    For 1200 baud channels that are shared with other packet users,
    an mtu value of 256 is reasonable; in fact, since that is the largest
    packet size most non-TCP/IP ham networks (like digipeaters and
    NetRom) are designed to handle, 256 is the largest mtu you should
    specify if any of your packets are going to travel via such a node.

    Faster networks may use higher values.  For good-quality channels
    with fast data rates (9600 baud or above), it may be reasonable to
    use an mtu ranging from 512 to 1500 (which matches the
    standard mtu used by ethernet systems).

    The other two parameters that set datagram size are part of the
    TCP protocol.  "tcp mss" (maximum segment size) is the largest
    chunk of data that TCP will send in a single frame.  Because the
    TCP and IP headers attached to each datagram total 40 bytes, mss
    should be 40 bytes smaller than mtu; 216 is the correct value for
    an mtu of 256.

    The "tcp window" parameter tells NOS how many datagrams it
    can have outstanding at once -- if it is twice the value of mss,
    NOS can receive two datagrams before sending an
    acknowledgment.  This parameter is analogous to the "maxframe"
    parameter in AX.25.  A large window improves efficiency because,
    among other things, multiple acknowledgments can be sent in a
    single packet.

    Although using a large window has major benefits on full duplex
    networks, on typical ham networks best performance comes from
    smaller windows ranging from one to three times the mss.  A good
    starting point is to set the window equal to twice the value of mss
    (432 for an mss of 216).

    In summary, good starting points are:

    1200 baud, shared channel:        9600 or faster, clear channel:
        mtu 256                    mtu 1500
        tcp mss 216                tcp mss 1460
        tcp window 432                tcp window 2920


    Even more than in other parts of this manual, this discussion
    glosses over lots of subtleties.  Throughput can be drastically
    affected by tuning these values, and both experimentation and
    local consensus are necessary to come up with settings that work
    well without stomping on other users of the channel.

                *** Using NOS ***

    To run NOS, first make sure you have your TNC configured for
    "KISS" mode (see Appendix F for details) and turned on.  Then,
    type NET, NOS, or GRINOS (as appropriate).  In a few seconds,
    you should see a "net>" prompt.  Any error messages that appear
    first probably indicate a problem with one or more commands in
    your AUTOEXEC.NET file.

    When you see the prompt, NOS is in "command mode."  When
    you are communicating with another host, NOS is in "converse
    mode."  To return to command mode from converse mode, press
    the F10 function key (sometimes called the "escape" key, but not
    to be confused with the "ESC" key on your keyboard).  All
    commands typed at the NOS prompt need to be followed by the
    return key.

    Typing "?" in command mode will display a list of commands.
    Typing a command name followed by ? will display the valid
    subcommands.  You can't really call it a help system, but it's
    better than nothing.

    Some commands can be abbreviated to save typing; the degree of
    abbreviation allowed depends on the command set of the NOS
    version you're using.  Experimentation is the best way to see what
    works and what doesn't.  One minor annoyance in GRINOS is that
    commands are case sensitive -- "c ax0 n8acv" is fine,  but "C ax0
    n8acv" isn't.  It's safest to do all your NOS keyboarding in lower
    case -- apart from case sensitive commands, in the Email world,
    typing in all upper case is considered shouting!

    You can issue several commands from within NOS to deal with
    files and directories.  "pwd" displays your current working
    directory, and "cd" allows you to change directories.  "dir"
    displays files in the current directory.  "mkdir <dirname>" creates
    a new directory, and "rmdir <dirname>" removes one.  "delete
    <filename>" erases a file.

    You can also "shell out" to DOS from within NOS by entering
    either an exclamation mark (!) or the command "shell."  To return
    to NOS, type "exit" at the DOS prompt.

    From command mode, you can start a number of different types of
    sessions to communicate with remote hosts.  Each session has its
    own display screen and you can switch between a session and
    command mode, or between sessions.  The se command displays
    the active sessions with identifying numbers.  To switch to a
    session, you can type "se <session number>."  From command
    mode, you can return to the current (most recently displayed)
    session by entering a carriage return.

    You can capture incoming data from the current session to a disk
    file by using the "record <filename>" command, and you can
    read in a data file from disk with the "upload <filename>"
    command.

    To close a session, press F10 to return to command mode and
    enter "close <session number>."  If there's only one session
    open, you can just enter "close."  You can also end the session by
    issuing the appropriate exit or quit command at the remote host's
    prompt.

    The most common NOS session types are probably "telnet," its
    cousin "ttylink", "ftp," and a regular packet "connect" (technically
    called an "ax25" session).  Telnet is used to "login" to a remote
    host, ttylink is a kind of telnet specially designed for keyboard-to-
    keyboard communications, ftp handles file transfers, and ax25
    sessions allow you to carry on normal packet activity.  We'll talk
    about ax25 sessions first, since they give you a chance to test
    your setup without having another TCP/IP station on the air.


    AX.25 Mode

    The "connect" command simply lets you do normal packet radio
    stuff.  Establishing an ax25 connect through NOS is like using the
    standard TNC commands with a few small differences.  First, since
    NOS can support several interfaces, each with its own hardware,
    you need to tell NOS which one to use.

    So, to connect to N8ACV on interface ax0, enter "connect ax0
    N8ACV."  Once you get a "Connected" message, you'll be able to
    type to the station at the other end just as you would with normal
    packet.  In addition to closing the session as described above, you
    can exit an ax25 session by typing "disconnect" at the command
    mode prompt.  (Just as with a TNC, these commands can be
    abbreviated; just how few of the letters are necessary will depend
    on each implementation of NOS and the commands it supports).

    The other minor difference between the NOS connect command
    and a regular TNC is that the word "via" is not used when
    specifying digipeaters.  To connect to N8ACV through N8KZA on
    interface ax0, you would enter "connect ax0 N8ACV N8KZA."


    Telnet

    The "telnet" command logs you in to a remote TCP/IP host;
    depending on the capabilities of that host, you might find yourself
    chatting directly with the user at the other end, connecting to the
    NOS mailbox, "mbox" (which acts very much like a sophisticated
    personal PBBS), or getting a UNIX "login:" prompt.  To establish a
    telnet session, enter "telnet <hostname>" at the command
    prompt.

    Some versions of NOS offer a new type of session that improves
    on telnet for real-time keyboard-to-keyboard chats.  It's called
    "ttylink," and it works just like telnet (for example, start a session
    with "ttylink <hostname>") except that it connects you directly
    to the remote host's chat mode, and uses a split-screen format to
    make things less confusing as you type to each other.

    You'll get a message like "Telnet session 1 failed: Reset/Refused
    errno 9" if the remote host doesn't support ttylink.  If the operator
    at the other end isn't available to chat, you'll get a message like
    "The system is unattended."  You'll still be able to type, but there
    won't be anyone there to reply.  You can change the status on
    your machine by setting the "attended" command to either on or
    off.  You might want to put this command in your AUTOEXEC.NET
    file to set your default status.  You exit from ttylink just as you
    would from telnet.

    And now a note from Miss Manners:  you should never simply exit
    from the NOS program when you have an open session.  Doing so
    can cause great unpleasantness at the remote host.  Unless you're
    in some sort of software or hardware lockup, or you know that the
    station on the other end has gone away, always close sessions
    and wait for confirmation before exiting the program.

    You should also be aware that your system may have started
    sessions in the background, for example to transfer electronic mail,
    or someone else may have started a session with your system.
    You may not even know these sessions are running.  Pulling the
    plug on them would be very impolite.  Before exiting NOS, you
    should first use the se command to make sure there are no current
    sessions running, and then the "tcp status" command to see if
    there are any background connections established.  "tcp status"
    will show you a long and confusing list of information; the
    important stuff at the end is the list of sockets (which are services
    your system can either offer or request on the network).  If
    anything other than "Listening" appears in the Status column, that
    means there's at least one remote host communicating with you.


    File Transfers

    You initiate a file transfer (ftp) session by entering "ftp
    <hostname>" at the command prompt.  Once the session is
    established, the remote host will prompt you for a user name and a
    password.  If your hostname and password have been added to
    the remote host's FTPUSERS file, you'll have the ability to
    download and perhaps upload files in the directories permitted you.

    If you haven't arranged with the remote host for your own
    account, you can try to login as "anonymous" or "guest;" many
    systems support these user names and grant limited (usually
    download-only) privileges to them.  If you login under one of these
    accounts, you should enter your hostname as the password; that
    allows the remote host to keep track of who's been using the
    system.

    Once you've logged in, you'll see a new prompt: "ftp>."  This will
    remind you that you're actually issuing commands to the remote
    computer.  From the ftp> prompt, you can list the files in a
    directory, change directories, upload files, or download files.

    To list files, enter "dir" at the ftp> prompt.  You will get a listing
    that shows subdirectories (if any) and files together with their
    dates and sizes.  To show the current directory name, type "pwd."
    To change directories, issue the "cd <directory>" command.
    Note that directories are displayed with a forward slash (/) instead
    of the usual MS-DOS backslash (\).  That's because the UNIX
    operating system, which is TCP/IP's natural home, uses forward
    slashes.  If the remote host is running NOS, you can use either
    character, but some other systems (particularly those running
    UNIX) will recognize only the forward slash.

    Once you've found a file you want to upload or download, you
    need to make a decision.  ftp can transfer the file either as an
    "image" file, byte for byte, or as an "ascii" file, converting the line-
    end character as necessary to compensate for different operating
    systems (UNIX uses only a linefeed character at the end of lines;
    MS-DOS uses carriage return/linefeed).  Before beginning a file
    transfer, enter "type i" for an image file, or "type a" for an ASCII
    file, at the ftp> prompt.

    What are the consequences choosing the wrong transfer type?
    Well, transferring a binary file as type "a" will almost certainly fail.
    Transferring an ASCII file as type "i" will work, but you may find
    that the line-ends are screwed up.  ASCII transfers are also quite a
    bit slower than image, because each line needs to be processed
    separately.

    To actually start a file transfer, use the command "put <local
    filename> <remote filename>" to send a file, or "get <remote
    filename> <local filename>" to receive one.  The file name can
    include a full path if you desire; remember to use the proper path
    separator character for the remote host.

    If you only specify one filename, ftp will assume that both the
    local and remote hosts will use the same name.  This can be
    dangerous if the remote host uses a different operating system
    than you do, as it may have filenames that are illegal on your
    system.

    If a file transfer goes awry, you can terminate it by going to
    command mode via F10 and issuing the "abort" command.  To
    end an ftp session, you can either type "quit" at the ftp> prompt
    (the preferred way), or you can close the session from the net>
    prompt.

    If you want others to be able to access files on your system, you'll
    need to set up an FTPUSERS file in your root directory.  Appendix
    E describes the contents of that file.

    Another message from Miss Manners:  transferring files via ftp is
    reliable, but can be slooooow, particularly at 1200 baud.  Before
    you start downloading a 250 kilobyte file, consider how busy the
    channel is, and whether you want to tie things up for (perhaps)
    several hours by your download.  NOS is polite and won't hog the
    channel, but don't doubt that a large file transfer will slow things
    down for everyone else.

    Other Protocols

    The "ping" protocol mentioned above is very useful to see if a
    remote host is on the air.  Just enter the command "ping
    <hostname>" at the NOS prompt.  If the host is available, you
    will see a response indicating what the round-trip time was to that
    host.  The time may be many seconds if you're going through
    gateways, so be patient.

    The "finger" protocol lets you see information about a remote
    host's users and services.  Entering "finger @<hostname>" (note
    the slightly different syntax -- the "@" symbol must immediately
    precede the remote hostname) will display a list of the finger files
    (described above) at that host.  Entering "finger
    <user@hostname>" will display the text file for that user.


            *** Electronic Mail ***

    We've saved NOS's electronic mail capabilities for last because
    they are a bit more involved than some other parts of the program.
    You use two programs to handle mail:  BM (a "user mail agent," in
    UNIX terms) to write and read messages, and NOS to send and
    receive them.  First we'll talk about reading and writing messages,
    and then about using NOS to transport them.


    Using BM.EXE to Read and Write Messages

    BM.EXE is a program that reads and writes mail message in the
    format TCP/IP systems recognize.  Contrary to popular belief,
    "BM" stands for "Bdale's Mailer" in honor of its creator, Bdale
    Garbee.  You can run BM from the DOS prompt just like any other
    program, from within NOS by shelling to DOS with ! or shell, or (in
    GRINOS) by typing the mail command from the net> prompt.

    Before using BM, you need to create its configuration file, BM.RC,
    which must live in the root directory of your disk.  An annotated
    BM.RC file is included as Appendix G.  Only the first three
    commands in the sample file are absolutely necessary to make BM
    work.

    There's a bit of controversy in some areas over the proper name to
    enter for "user" in BM.RC.  Some folks recommend using either
    your first name, or your initials (for example, my address would be
    "[e-mail]") while other suggest using the callsign
    instead ("[e-mail]").

    While using the callsign may seem more impersonal, it has major
    advantages when mail is moving between TCP/IP and the packet
    BBS system, or when using the POP server; we strongly
    recommend that you use the "callsign@hostname" format unless
    the locals object even more strongly.  It's important to be
    consistent within the area, so that everyone knows how to
    address mail to everyone else.

    When you start BM, you'll see a prompt such as "ag9v>"
    showing the default mailbox (based on the "user" entry in BM.RC).
    As in NOS, you enter commands at the prompt, following them
    with a carriage return.  Most BM commands are single letters,
    optionally followed by a mail addressee or a message number (or
    numbers).

    To send mail, use the command "m <addressee>."  The
    addressee will normally be a user at a remote host; for example,
    ag9v might send mail to k8gkh@k8gkh.  The single biggest
    problem with BM is forgetting to include the hostname -- in other
    words, sending mail to <user> rather than
    <user>@<hostname>.   Without the hostname, BM will think
    the user is on your local system, and the mail will end up being
    stored in a mailbox under that user's name on your own system.
    That doesn't work too well.

    One way to solve that problem, and do some other interesting
    things, is to create an ALIAS file in your root directory.  When you
    send a message, BM will compare the addressee with the alias file,
    and if it finds a match will replace the alias with a full address from
    the file.  An alias can point to a list of addresses, so it's possible
    to define an alias that will send a copy of the message to everyone
    in your local group.  A sample alias file might look like:

    greg    [e-mail]
    bill    [e-mail]
    club    [e-mail] [e-mail]
        [e-mail] [e-mail]

    The alias for "club" demonstrates two things:  a single alias can
    expand to several addresses, and you can continue a long address
    list on subsequent lines by indenting them with spaces or a tab
    character.

    Now, if you send mail to "greg" it will automatically be expanded
    to the full address, and by sending a message to "club" all four
    users will get a copy.

    By the way, you do not use a trailing dot after an FQDN (as
    discussed above) in Email addressing; doing so will screw things
    up.

    If you use BM's built-in editor to compose messages, remember
    that it doesn't wrap lines; you have to hit the carriage return at the
    end of each line.  Use the "l" command to list outbound mail; you
    can kill an outbound message with the "k <msg#>" command,
    using the message number obtained from the "l" command.

    Several commands are used to deal with incoming mail.  "h"
    displays the headers (summary info) about messages in your
    mailbox.  It is the basic command you should use to check your
    incoming mail.  Each header displayed includes a message number
    to use with the other message manipulation commands.
    Commands given without a message number act on the current
    message (the one marked with an ">" in the display from the "h"
    command); if there's only one message, it is always the current
    one.

    BM can support multiple users at a single host; a separate mailbox
    is created for each user.  Unfortunately, BM has no way of
    knowing if incoming mail addressed to <someuser>@<yourhost> is
    valid, so it will happily accept such mail and create a new mail-
    box for <someuser>.  You may never know it's there, unless you use
    the "n" command to display the list of mailboxes.  You can also use
    "n" to change to a different mailbox: "n <mbox>."

    The commonly used commands (which may be followed by one or
    more message numbers if appropriate) are:

    msg#    message number by itself will display that message and
        set it as the current message.
    r    reply to a message.
    d    delete a message.
    s    save a message; if a file name follows the message
        number(s), the message(s) will be saved in that file.
        Otherwise, they'll be saved in the default mbox file.
    u    undelete a message previously marked for deletion.
    p    print a message on the local printer.
    w    save a message to a file without including headers.
    f    forward a message to another recipient.
    b    bounce a message.  Like forward, but keeps the original
        sender information intact (i.e., the message will not
        appear to have been sent by you).
    $    update the mailbox.  This deletes messages marked for
        deletion and reads in any new mail that may have arrived
        since you started BM.

    There are two commands that exit from BM:  "x" will exit without
    updating the mailbox.  In other words, the same messages will be
    there the next time you run the program.  "q" updates the mailbox
    (like "$") and then exits.

    Outbound mail created by BM is stored in the \spool\mqueue
    directory, where it waits patiently until one of NOS's servers
    (SMTP or POP) attempts to send it to its destination.


    Moving Mail With NOS

    Now, to the mechanics of getting mail into and out of your
    system.  All mail that you create is sent to its destination (or at
    least to the next stop on the way) by the "smtp" server in NOS.
    The "smtp timer" command (set in AUTOEXEC.NET) tells smtp
    how often to scan the \spool\mqueue directory for outgoing mail.
    When it finds some, it attempts to open an smtp session to the
    remote host in the address and send the mail there.  There's no
    default for the smtp timer value, so your AUTOEXEC.NET file
    should include something like "smtp timer 600" (which scans for
    mail every ten minutes).  You can manually force smtp to scan the
    queue by issuing the "smtp kick" command from the net> prompt.

    If you have a local mail server with connections to the outside
    world, you can use it to route mail for hosts that aren't in your
    domain file with the "smtp gateway <hostid>" command.

    Incoming mail can arrive at your station when a remote host does
    this and starts an smtp session with you.  But if you don't keep
    your station up 24 hours a day, the remote host will be trying, and
    trying, and trying, to connect with you until you finally show up.
    A far better approach is to use "POP" -- the Post Office Protocol.
    If your system runs POP, and someone in the area has agreed to
    be a POP server, NOS will automatically contact that server when
    you come on the air; the server will respond by sending the mail
    waiting in your mailbox.  You can then read it with BM just as if it
    had arrived via smtp.

    To use POP, the server must establish a mailbox and password for
    you, and you need to add the appropriate commands to your
    AUTOEXEC.NET file (see the annotated AUTOEXEC.NET file in
    Appendix B).

    Remember that smtp or POP sessions may be running in the
    background without your knowing about it.  Always check for
    activity with the "tcp status" command before pulling the plug!

    Additionally, smtp creates lock files in \spool\mqueue when it tries
    to send outgoing mail.  If NOS is killed before the mail transfer has
    succeeded, these files (with the extension ".LCK") will be left
    behind and if they are not manually removed, they will prevent
    smtp from trying again to send those messages.  To prevent this,
    you should always issue the command "erase \spool\mqueue\*.LCK"
    before starting NOS.  It's a good idea to launch NOS using a batch
    file that removes the locks before executing the program.

                *** Conclusion ***

    This has been a whirlwind tour of TCP/IP.  Once you have the
    software installed, it's not hard to use, and NOS truly opens the
    door to enjoying packet radio in a whole new way.

    To learn the subtleties of NOS, you should do two things:  read
    the reference manual for the version you're using, and experiment
    with the program.  Once you know the ins and outs, please share
    your knowledge with others.  The ham radio TCP/IP community is
    still small, and we need all the Elmers we can get!


    John Ackermann   AG9V
    2371 Stewart Road
    Xenia, OH   45385

    TCP/IP:        [e-mail].  [44.70.12.34]
    PBBS:        [e-mail]
    Internet:    [e-mail]
    CompuServe:    72300,1160


    APPENDIX A
    Resources for NOS and TCP/IP

    (Note:  This is a very incomplete list; please feel free to provide
    additional resources to add for the next edition!)

    TAPR
    P.O. Box 22888
    Tucson, AZ   85734

    The New England TCP Association
    3628 Acushnet Ave.
    New Bedford, MA   02745

    APPENDIX B
    Sample AUTOEXEC.NOS File for GRINOS

    # AUTOEXEC.NET
    # This is a sample autoexec file for GRINOS version N1BEE 0.72.
    # It doesn't have all the fancy features one might hope for, but
    # the basics are there, with some hopefully useful comments.
    # Any line beginning with a "#" character is treated as a comment.
    # To uncomment a line, delete the # character

    # These are a couple of things for NOS to use internally.
    mem eff on
    watchdog on
    nibufs 10

    # NOS needs to know three things about you:  your hostname,
    # your  ham callsign, and your IP address.  By convention, the
    # hostname # is your callsign in lower case, followed by ".ampr.org".
    # The  callsign is generally used in upper case to distinguish it.
    # The IP address comes from a local area coordinator.  Note that
    # there are a minimum of three places in this file where you need to
    # insert your IP address -- here, in the ifconfig command, and at the
    # end of each attach command.
    hostname nocall.ampr.org
    ax25 mycall NOCALL
    ip address [44.xx.xx.xx]

    # This should match your IP address
    ifconfig loopback ipaddress [44.xx.xx.xx]

    # This makes short forms of the hostname work.
    domain suffix ampr.org.

    # NOS needs to know how to convert hostnames to IP addresses.
    # You can do this manually via the "DOMAIN.TXT" file, or you can
    # use a nameserver if one is available.  To enable the
    # nameserver, uncomment this line and plug in its correct
    # address.
    #domain addserver [44.xx.xx.xx]

    # Some additional commands for the domain service.  Don't turn
    # translate on unless you have a small domain file and/or a fast machine.
    domain verbose off
    domain cache size 40
    domain translate off

    # To use POP, uncomment these lines.  Fill in "pop mailhost" with
    # the IP address of the station serving as your POP server.  Fill in the
    # "pop# mailbox" name with your hostname, i.e., your call.  The "pop
    # userdata" line needs to have your hostname, followed by a password
    # (as negotiated with your mail server).  "pop timer" sets
    # how often, in seconds, to query for mail.
    #pop mailhost [44.xx.xx.xx]
    #pop mailbox hostname
    #pop userdata hostname password
    #pop timer 1800

    # Attach commands are complex; these are samples for COM 1
    # and 2.  See Appendix C for details.  Uncomment the
    # appropriate line(s) for your hardware.
    # COM1 -- 256 byte MTU, 4800 baud serial link as ax0
    attach asy 0x3f8 4 ax25 ax0 2048 256 4800
    # COM2 -- 256 byte MTU, 4800 baud serial link as ax1
    #attach asy 0x2f8 3 ax25 ax1 2048 256 4800

    # This is the basic route, sending everything out ax0
    route add default ax0

    # These are tcp parameters you shouldn't need to mess with.
    ip ttl 16
    ip rtimer 240
    tcp irtt 3000

    # On a shared channel, you may want to change timertype to
    # exponential; that's more courteous, but will slow your
    # retries down significantly.  mss and window should ordinarily be
    # the same value, equal to the largest mtu set in the attach
    # command(s) above minus 40.  With the common mtu for 1200 baud
    # channels of 256, that means both mss and window should be 216.
    tcp timertype linear
    tcp bblimit 16
    tcp mss 216
    tcp window 216

    # These set up AX.25 parameters
    ax25 digipeat off
    ax25 maxframe 1
    ax25 paclen 256
    ax25 retry 20
    ax25 window 4096
    ax25 blimit 15
    ax25 version 2

    # as with tcp timertype, you may want to set this to
    # exponential on a shared channel.
    ax25 timertype linear

    # These are netrom setup commands.  Don't turn them on
    # unless you need them, and you know what you're doing.  You
    # can really screw up the network by putting out netrom
    # broadcasts that don't fit with the configuration of the
    # "real" netrom nodes that can hear you.
    #attach netrom
    #netrom interface ax0 MYALIAS 192
    #netrom obsotimer 1800
    #netrom nodetimer 10800
    #netrom verbose yes
    #netrom bcnodes ax0
    #netrom ttl 8

    # These start the servers.
    start smtp
    start ftp
    start echo
    start discard
    start telnet
    start finger
    start ax25

    # Uncomment this line to enable logging.
    #log \spool\net.log

    # Default file type for ftp transfers.  Type image is for binary files;
    type
    # ascii is for text; it's safest to set the default to image.
    ftype image

    # This makes telnet sessions to Unix systems work
    # line-by-line, rather than character-by-character.
    echo refuse

    # Tell smtp how often to scan for outgoing mail
    smtp timer 600
    smtp batch on

    # GRINOS can send a string of commands to the TNC on startup.
    # You could use this to force the TNC into KISS mode.  Note that
    # you need to specify which interface to use.  This must be done
    # <after>defining the interface, and <before>any data is sent to
    # the TNC (for example, by the smtp and pop kick commands below).
    # These commands will do that for a TNC2:
    comm ax0 "kiss on"
    comm ax0 "reset"

    # kick the smtp and POP servers at startup.  Only uncomment the
    # "pop kick" line if you've defined a POP server above.
    smtp kick
    #pop kick

    # GRINOS (but not other versions) can define the function
    # keys with macros to make things a bit easier.  Here are a
    # couple of examples.  Note that each command must end with
    # a "\n" to signify a carriage return.  The numbers
    # represent the keys; 59 - 68 for F1- F10 (though F10 can't
    # be redefined; it's always the escape key), 84 - 93 for
    # shiftF1 - shift F10, 94 - 103 for ctrlF1 - ctrlF10, 104 -
    # 113 for altF1 - altF10.
    fkey 59 "tcp status\n"
    fkey 60 "mem status\n"
    fkey 61 "status\n"

    # THE END

    APPENDIX C
    Designing ATTACH Commands

    NOS supports a number of versions of the attach command to deal
    with different hardware.  We'll discuss three of them here:  asy,
    used for serial port connections; pi, used to connect to the Ottawa
    PI card; and packet, used to interface to hardware supporting the
    FTP, Inc., packet driver protocol.  As usual, this discussion covers
    the basics; see the NOS reference manual for details on all the
    many options.

    Hosts normally have a separate IP address for each interface.  If
    you are running more than one interface, you can include that
    interface's IP address (in [xx.xx.xx.xx] form) at the end of the
    attach command.

    The asy version provides an interface to a standard PC serial port.
    The syntax is:

    attach asy <ioaddr> <vector> <mode> <if> <bufsize>
        <mtu> <speed>

    In English, these parameters are:

    ioaddr -- the address of the COM port being used.
    COM1 is usually 0x3f8 and COM2 is usually 0x2f8.
    COM3 and COM4 aren't standardized; using them will
    require looking at the documentation for your serial card,
    and probably some experimentation.

    vector -- the IRQ used by the hardware.  COM1 is usually
    4, and COM2 is usually 3.  Again, COM3 and COM4
    vary.

    mode -- this specifies the nature of the interface.  ax25 is
    for a connection to a KISS TNC, slip for a hardwired
    connection to another host, ppp for a dial-up connection,
    and nrs is for attaching a NOS station to a NetRom node.

    if -- the interface name.  The convention is to use ax0,
    ax1, etc., for KISS interfaces.

    bufsize -- the buffer for incoming data, in bytes.  Usually
    a value of 1024 is more than sufficient for a 1200 baud
    channel.

    mtu -- the maximum transmission unit size, in bytes.  See
    the discussion in the main text on this subject.

    speed -- the speed of the serial (not radio) link, in baud.
    The best setting for this will depend on the speed of your
    computer, but generally two to four times the radio
    speed is adequate.

    Some sample attach asy commands are:

        # COM1, KISS TNC as ax0, MTU 256, 4800 BAUD
        attach asy 0x3f8 4 ax25 ax0 1024 256 4800

        # COM2, KISS TNC as ax1, MTU 256, 2400 BAUD
        attach asy 0x2f8 3 ax25 ax1 1024 256 2400

        # SLIP link, COM1 as sl0, MTU 256, 9600 BAUD
        attach asy 0x3f8 4 slip sl0 1024 256 9600

    The Ottawa PI card is a plug-in board for PCs designed for high-
    speed performance.  It has two ports, one DMA driven for high
    speed and the other interrupt driven.  The attach syntax is:

    attach pi <ioaddr> <vector> <DMA chn> <mode> <name>
        <bufsize> <mtu> <speed a> <speed b>

    A sample attach command (using the PI's default jumper settings)
    is:

        attach pi 380 7 1 ax25 pi0 1750 1024 0 1200

    In this example, the interface name for the DMA port is "pi0a" and
    the second port is "pi0b".  Because the port a speed is 0, the PI
    card expects the modem to provide its own clocking.  The PI
    attach syntax is explained in the manual provided with the card.

    Finally, the packet interface is used to connect to ethernet cards
    and other hardware that supports the FTP, Inc. "packet driver"
    standard.  There's a packet driver for the PI card.  The syntax is:

        attach packet <ioaddr> <vector> <if> <bufsize> <mtu>

    In this case, ioaddr and vector need to match those used for the
    packet TSR that supports the hardware.  bufsize is the number of
    packets (not bytes) that may be outstanding.  For ethernet, the
    standard mtu is 1500.

    APPENDIX D
    The DOMAIN.TXT File


    # The domain.txt file contains mappings between hostnames
    # and IP addresses.  The file can be quite complex, but
    # basic entries usually resemble this.

    # Fields are separated by tabs or spaces.

    # These are normal address records.  The first field is the
    # hostname.  The second field is a "time to  live" value
    # returned by the name server.  If you manually create an
    # entry, you can leave this field  blank.  The third field
    # is always "IN" to signify these are internet addresses.
    # The fourth field is "A" to signify an address record.  The
    # last field is the address.

    k8gkh.ampr.org.9886    IN    A    44.70.12.31
    ag9v.ampr.org.    3584    IN    A    44.70.12.34

    # This is a "canonical name" (CNAME) record that maps an
    # alias to an official hostname.

    server.ampr.org.    3599    IN    CNAME    ag9v.ampr.org.

    APPENDIX E
    Sample FTPUSERS File

    # This file establishes ftp user permissions.  Fields are
    # separated by exactly one space.  The privileges value is a
    # bitmask.  The only values significant for ftp are:

    # 1 - read only
    # 3 - read/write
    # 7 - read/write/overwrite/delete


    anonymous * /pub 1        # no password, read only in /pub
    friend foobar /pub 3        # read/write privileges in /pub
    spouse snoogums / 7        # read/write/delete everywhere

    APPENDIX F
    Making Your TNC Talk in KISS MODE

    Once NOS is installed and your configuration files set, you need to
    do one more thing:  get your TNC talking to your computer in KISS
    (Keep It Simple, Stupid) mode.  KISS is a special protocol that lets
    your computer do the work of processing packets; the TNC does
    only the very low-level packet assembly and disassembly
    functions.  Nearly all TNCs support KISS in one way or another.

    Typically, you'll need to issue commands to the TNC to set the
    serial line baud rate to the same speed as you've specified in the
    attach command, to 8 bit data, and to no parity.  Then, issue the
    KISS command (on a TNC2, kiss on), and the TNC's software
    reset command.  After that, you won't be able to talk to your TNC
    via the terminal program, but NOS will be able to.  (And don't
    worry, you can easily return the TNC to normal mode if you want
    to.)  Once you've done this, you're set to run NOS.

    One trick that grinos supports is the ability to send commands to
    the TNC during startup.  The comm command will send a string of
    text to the named interface.  For example, to force a Kantronics
    DataEngine or KAM into KISS mode every time you start NOS,
    include the following commands in AUTOEXEC.NOS (after you've
    defined the interface with the attach command):

    comm ax0 "interface kiss"
    comm ax0 "reset"

    Note that surrounding the text with quote characters will preserve
    spaces in the command.

    Appendix G
    A Sample BM.RC File

    # BM.rc

    # your hostname -- note that for mail we <don't> put a trailing
    period at
    # the end of the FQDN.
    host ag9v.ampr.org

    # the user name (one host can receive mail for several users);
    # usually your callsign
    user ag9v

    # your full name, for the message "From:" line
    fullname John Ackermann

    # if you want to have replies sent to another host, because, for
    # example, you are using a POP server, this line specifies where
    # replies should go
    reply [e-mail]

    # for faster screen writes on the pc, use direct video, not bios
    screen direct

    # if you want to use an editor different than BM's built-in one
    edit ed

    # put saved messages here; note "/" instead of "\"
    mbox c:/folder/mbox

    # save a copy of outbound mail here
    record c:/folder/outmail

    # folder for your mail
    folder c:/folder

    # maximum number of messages that can be pending
    maxlet 200