Magazyn Enter 1999 April

home *** CD-ROM | disk | FTP | other *** search

/ Magazyn Enter 1999 April / enter_04_1999_cd2.iso / MAT3 / backup / DATA.4 / SYSTEM / TAPEERR.dll / string.txt

Wrap

Text File | 1995-09-28 | 43KB | 1,092 lines

0 NO ERROR 1 DCB ERROR NO MEMORY 2 MAXIMUM DEVICES REACHED 3 BAD DEVICE NUMBER 4 DEVICE ALREADY OPEN 5 DEVICE NOT OPEN 6 DEVICE ALREADY LOCKED 7 DEVICE NOT LOCKED 8 BAD DEVICE HANDLE 9 FAILED WRK BUFFER ALLOC 10 ALLOC WRKBUFFER NO MEMORY 11 TAPE PROCESSES AT ZERO 12 TAPE PROCESSES AT MAXIMUM 13 INVALID TAPE DEVICE 14 CREATE TAPECONSOLE FAILED 15 CREATE SCANDAEMON FAILED 16 CANNOT LOAD DLL ERROR 17 CANNOT OPEN LOAD FILE 18 CANNOT READ LOAD FILE 19 LOAD FILE ERROR 20 LOAD FILE DONE 21 NO COMMAND LINE AVAILABLE 22 CANNOT SET TAPE BLOCKSIZE 23 ERROR INVALID HANDLE 24 BAD ENTRY POINT TABLE 25 ERROR ILLEGAL SCSIID 26 ILLEGAL GROUP NAME 27 NO DEVICES FOUND 28 BAD GROUP NUMBER 29 NON EXISTENT GROUP 30 NO MEMORY FOR IO BUFFERS 31 CANNOT ALLOCATE DAEMON LIST BUFFERS 32 FAILED TO CREATE READ DAEMON 33 FAILED TO CREATE WRITE DAEMON 34 NO JOB GIVEN 35 DEVICE NOT USED 36 BAD PARAMETER PASSED 37 JOB DENIED GRP NA 38 JOB DENIED MAXIMUM JOBS REACHED 39 JOB DENIED NO MEM 40 JOB DENIED GRP BSY 41 JOB DENIED COMM ERROR 42 JOB DENIED ILLEGAL CLIENT TYPE 43 JOB DENIED FAILED TO CREATE DAEMON 44 JOB DENIED ILLEGAL JOB TYPE 45 BAD JOB HANDLE 46 DAEMON ALREADY CREATED 47 INVALID FUNCTION 48 SECTION PARAMETER NOT FOUND 49 ERROR GROUP NAME ALREADY REGISTERED 50 ERROR DEVICE ALREADY REGISTERED 51 COMM FAILURE 52 FAILED TO WRITE VOLUME HEADER 53 NO MEMORY FOR JCB TABLES 54 COMPRESSION ERROR ILLEGAL DRIVE TYPE 55 PADDING ERROR ILLEGAL DRIVE TYPE 56 NO DEVICES FOUND TO LOCK 57 NO DEVICES FOUND TO UNLOCK 58 ERROR WRITE DAEMON SUSPENDED 59 ERROR READ DAEMON SUSPENDED 60 ERROR DAEMON ABORTED 61 ERROR UNKNOWN DAEMON ERROR 62 ILLEGAL ERASE MODE 63 INTERMEDIATE PKT 64 OPEN FAILED SCANNING BUSY 65 ERROR NO PARAMETERS GIVEN 66 DAEMON ILLEGAL BUFFERADDRESS 67 DAEMON BUFFER TOO LARGE 68 INVALID TAPE DRIVE 69 TAPE BUSY SEMAPHORE NOT CREATED 70 TAPE BUSY SEMAPHORE FAILURE 71 TAPE UNBUSY SEMAPHORE NOT CREATED 72 TAPE UNBUSY SEMAPHORE FAILURE 73 TAPE COPY ERROR 74 TAPE COPY NOSPACELEFT 75 TAPE MISCOMPARE ERROR 76 TAPE COMPARE OUTOFSYNC ERROR 77 TAPE HEADER MISCOMPARE ERROR 78 TAPE COMPARE GENERAL ERROR 79 TAPE COPY BUSY 80 TAPE COMPARE BUSY 81 DEVICE NOT A TAPE DRIVE 82 JOB DENIED TAPEENG DISABLED 83 ERROR DAEMON NOT INITIALIZED 84 ERROR BOARD VERSION NOT SUPPORTED 85 ERROR LOST TAPE ENGINE CONNECTION 86 REENTRANCY ERROR OPEN DEVICE TIMEOUT 87 REENTRANCY ERROR CANNOT OPEN MULTIPLE DEVICES 88 ERROR STARTING NAME OUT OF RANGE 89 ERROR MEDIA IS BLANK 90 ERROR BUFFER PASSED IS NULL 91 TAPEENG ERROR NO MEDIA IN DRIVE 92 ERROR SYNC READ TOO LARGE 93 ERROR SYNC WRITE TOO LARGE 94 ERROR ILLEGAL SHOTS VALUE 95 ERROR ILLEGAL SCSIID VALUE 96 ERROR FAILED TAPEENG DEACTIVATE GROUPS ACTIVE 97 ERROR FAILED GROUP UNLOAD GROUPS ACTIVE 98 ERROR ILLEGAL BLOCKSIZE VALUE 99 ERROR UNKNOWN CFG CONDITIONAL 100 ERROR DEVICE NOT READY 101 ERROR ILLEGAL SLOTS VALUE 102 ERROR ALLOCATING CHANGER MEMORY 103 ERROR BAD DLL SIGNATURE 104 ERROR MAXIMUM DLLS REACHED 105 ERROR BAD GROUP SIGNATURE 106 ERROR MAXIMUM GROUPS REACHED 112 ERROR FAILED TO REGISTER GROUP INFO 113 ERROR CONFLICTING DEVICES DETECTED IN GROUP 114 ERROR NO GROUP NAME GIVEN ON CMDLINE 115 ERROR ILLEGAL COMMAND LINE PARAMETER 116 ERROR ILLEGAL SCSIID PARAMETER 117 ERROR NO SCSIID GIVEN TO PARAMETER 118 JOB DENIED TAPENAME NOT FOUND 119 ERROR NO VALID RESIDUE INFO 120 ERROR QFA CHUNK OFFSET SURPASSED 121 ERROR QFA ILLEGAL MODE 125 CONNECTION FAILED TO OPEN ARCSERVE HOM 126 UNPROCESSED PKT 127 COMMUNICATION FAILURE 128 TOO MANY BLOCKS 129 NO MEMORY AVAILABLE WHEN ATTEMPTING TO ALLOCATE MEMORY BUFFER 130 OFFSET TOO BIG 131 INVALID COMMAND 132 ERROR VALIDATE NOT LOADED 133 ERROR MISSING BOARD ENTRY POINT 134 ERROR BCB TABLES FULL 135 ERROR BCB DUPLICATE NAME FOUND 136 ERROR BCB BOARD NUMBER OUT OF RANGE 137 ERROR DAEMON BUFFERSIZE OUT OF RANGE 138 ERROR ILLEGAL BUFFERSIZE GIVEN 139 ERROR BAD DELIMITER GIVEN 140 ERROR NO BOARD DRIVER NAME GIVEN 141 ERROR BOARD NAME NOT FOUND IN LIST 142 ERROR TAPECAPACITY NOT SUPPORTED 143 ERROR BOARD DOES NOT EXIST 144 ERROR TAPEENG ALREADY DEACTIVATED 145 ERROR CANNOT CONNECT TO TAPE ENGINE. 146 ERROR FAILED TO REGISTER DOWN EVENT 147 ERROR COPY FAILED DRIVES NOT SAME 148 ERROR COMPARE FAILED DRIVES NOT SAME 149 JOB DENIED VOLUME HEADER ILLEGAL BLOCK LENGTH 150 ERROR TAPECOPY MEDIUM ERROR ON SOURCE 151 ERROR TAPECOPY HARDWARE ERROR ON SOURCE 152 ERROR TAPECOPY NO TAPE IN SOURCE DRIVE 153 ERROR TAPECOPY UNIT ATTENTION SOURCE 154 ERROR TAPECOPY MEDIUM ERROR ON DESTINATION 155 ERROR TAPECOPY HARDWARE ERROR ON DESTINATION 156 ERROR TAPECOPY NO TAPE IN DESTINATION DRIVE 157 ERROR TAPECOPY UNIT ATTENTION DESTINATION 158 ERROR TAPECOPY CANNOT CREATE COPY DAEMONS 159 ERROR TAPECOMPARE MEDIUM ERROR ON SOURCE 160 TP NO ERROR 161 ILLEGAL COMMAND 162 PHYSICAL END OF MEDIA 163 FILEMARK DETECTED 164 NO DATA DETECTED 165 UNRECOVERABLE DATA ERROR 166 CARTRIDGE NOT IN PLACE 167 CONTROLLER FAILURE or HARDWARE ERROR 168 CARTRIDGE WRITE PROTECTED 169 PHYSICAL BEGINNING OF MEDIA 170 EARLY WARNING 171 UNIT ATTENTION:SCSI BUS Reset, drive power lost, or media change 172 COPY ABORTED 173 COMMAND ABORTED 174 TP ILLEGAL BLOCK SIZE 175 TP RESERVATION CONFLICT 176 TP SCSI BUSY 177 ERROR TAPECOMPARE HARDWARE ERROR ON SOURCE 178 ERROR TAPECOMPARE NO TAPE IN SOURCE DRIVE 179 ERROR TAPECOMPARE UNIT ATTENTION SOURCE 180 ERROR TAPECOMPARE MEDIUM ERROR ON DESTINATION 181 ERROR TAPECOMPARE HARDWARE ERROR ON DESTINATION 182 ERROR TAPECOMPARE NO TAPE IN DESTINATION DRIVE 183 ERROR TAPECOMPARE UNIT ATTENTION DESTINATION 184 ERROR TAPECOMPARE BLOCK COUNT DIFFER 185 ERROR TAPECOMPARE FILEMARKS OUT OF SYNC 186 ERROR TAPECOPY ZERO BLOCKS READ SOURCE 187 ERROR TAPECOPY NOSPACELEFT 188 ERROR FAILED TO CREATE GROUPBSY SEMAPHORE 189 ERROR ILLEGAL LOG SELECTION 190 ERROR ILLEGAL DENSITYCODE VALUE 191 ERROR BAD MSG HANDLE GIVEN 192 ERROR MSG TABLE FULL 193 ERROR CHANGERID OUTOFRANGE 194 ERROR ILLEGAL CHANGERID CHARACTER 195 ERROR DEVICE IS BUSY 196 ERROR TAPE NOT FOUND 197 ERROR INVALID TAPE INDEX 198 ERROR SLOT IS EMPTY 199 ERROR CLEANING CARTRIDGE NOT INSTALLED 200 ERROR SLOT IS OCCUPIED 201 ERROR TAPE DRIVE IS LOADED 202 ERROR NO GROUP ASSIGNED 203 ERROR SLOT RANGE EMPTY 204 ILLEGAL PARAMETER 205 DEVICE ALREADY IN GROUP 206 ILLEGAL ADAPTER NO 207 NO REGISTRY 208 ILLEGAL DATA 209 REG CANNOT OPEN REGISTRY 210 REG ERROR QUERY KEY 211 REG ERROR QUERY VALUE 212 REG CANNOT OPEN KEY 213 REG CANNOT LOCATE KEY 214 REG CANNOT ADD VALUE 215 REG VALUE TYPE MISMATCH 216 REG CANNOT CREATE KEY 217 REG CANNOT DELETE KEY 218 REG CANNOT WRITE VALUE 219 REG ILLEGAL DATA 220 REG CANT GET VALUE 221 NEW DEVICE 222 MISSING DEVICE 223 DEVICE PARAMETER MISMATCH 224 GROUP ALREADY OPEN 225 GROUPS OPEN 226 TAPEENG ALREADY LOCKED 227 JOB ATTACHED TO A GROUP 228 MAXIMUM SESSIONS REACHED 229 INCOMPLETE SESSION 230 DEVICE GROUP MISMATCH 231 SLOT IS CLEANING TAPE 232 BAD TAPE 233 MAGAZINE DISMOUNTED 234 TAPEENG INITIALIZING 235 GROUP NAME EXISTS 236 ERROR WRITING TO CONFIG FILE 237 FIND GROUP EXHAUSTED 238 ENUM TAPE STATUS EXHAUSTED 239 CAN NOT FIND THE TAPE TO BE CONNECTED 240 DYNAMIC GROUPING ACTIVE 61480 Tape Engine is UP! 61481 Format Tape %-.23s - Exp Date: %s 61482 Resources in use. ARCserve must be unloaded first. 61483 Tape Engine unloading... 61485 E6000 Error Formatting: %s 61486 Format Successful! 61487 E6001 Error Erasing: %s 61488 Erase Successful! 61489 Two devices are necessary for Copy 61490 E6002 Error Copying: %s 61491 Copying Successful! 61492 E6003 Error Retensioning: %s 61493 Retensioning Successful! 61494 E6004 Error Setting Compression: %s 61495 Setting Compression Successful! 61496 WARNING - Formatting will destroy all data on the tape!!! 61497 existing data on tape!! 61498 WARNING - Erasing will destroy all 61499 Choose a Device: 61500 Tape Name: 61501 Expiration Days: 61504 Formatting %s device %d 61505 Erase Mode: 61506 Performing %s Erase 61507 DEVICE MANAGEMENT - Erasing Tape 61508 %s Erasing Device %d 61509 WARNING - Copying will overwrite all data on destination tape!! 61510 existing data on destination tape!! 61511 Source Device : 61512 Destination Device: 61513 Source & Destination MUST be different devices 61514 Source & Destination drives MUST be the same type 61515 Retensioning 61516 DEVICE MANAGEMENT - Retension 61517 Retensioning Device %d 61518 WARNING - Compression will only be 61519 changed on blank or erased tapes. 61520 Compression: 61521 DEVICE MANAGEMENT - Tape Drive Status 61522 Log Select Disabled 61523 Devices, Groups, and Miscellaneous 61524 Choose an Item: 61533 WARNING - Erasing will destroy all data on the tape!!!! 61536 Copying Device %d to Device %d 61537 %csynchronous protocol from server to client 61540 Expiration Date: 61547 Log all messages 61548 Log only hard error sense information 61549 Log messages to screen only 61550 Log messages to file only 61551 Log messages to both screen and file 61552 Log SCSI IDs 61553 System Configuration 61554 Device to Monitor 61555 Read Timeout 61556 Write Timeout 61557 Rewind Timeout 61558 Message Type 61559 No messages displayed/logged 61560 Messages will be displayed/logged only on error 61561 All messages will be displayed/logged 61570 Mode Select 61571 EOM 61572 Space FM 61573 Space Blocks 61574 Write Filemark 61575 Seek Block 61576 Mode Sense 61577 Save new parameters? 61578 Scanner Delay 61579 No additional sense 61580 Filemark detected 61581 End of tape encountered 61582 Setmark was detected 61583 Beginning of media detected 61584 End of data detected 61585 Not in legal mode for read - Illegal command 61586 I/O Process terminated 61587 Peripheral device write fault 61588 Excessive write errors 61589 Device will not become ready - cause unknown 61590 Device in process of becoming ready 61591 E6005 Device will not become ready - initialization required 61592 Manual intervention needed 61593 E6006 Logical unit does not respond to selection 61594 Multiple peripheral devices selected 61595 E6007 Logical unit failure 61596 E6008 Device communication failure 61597 E6009 Device communication parity error 61598 E6010 Track following positioning error 61599 E6011 Error log overflow 61600 E6012 Write error - head sync error during write 61601 E6013 Unrecovered read error 61602 E6014 Uncorrectable block encountered during read 61603 E6015 Error too long to correct 61604 E6016 Too many permanent read errors - cannot re-synchronize 61605 E6017 Incomplete block read (postamble not found) 61606 E6018 Recorded entity not found or basic media error 61607 Record not found or basic media error 61608 E6019 Filemark or setmark not found 61609 E6020 End of data not detected - corrupt format 61610 E6021 Block sequence error 61611 E6022 Mechanical positioning error 61612 E6023 Servo - Mechanical positioning error 61613 E6024 Positioning error detected by read, space, or locate 61614 E6025 Recovered with no ECC applied 61615 E6026 Recovered with retries 61616 E6027 Recovered with ECC applied 61617 E6028 Mode select parameter error 61618 E6029 Synchronous data transfer error 61619 E6030 Invalid command operation code 61620 E6031 Logical block is out of range 61621 E6032 Invalid element address - changer 61622 E6033 Invalid field in CCB 61623 E6034 LUN not supported 61624 E6035 Parameter not supported - flash eeprom problem 61625 E6036 Write buffer permanent value invalid 61626 E6037 Threshold parameters not supported 61627 Media is write protected 61628 Hardware write protected 61629 Software write protected 61630 Read only format 61631 E6038 Not ready to ready transition 61632 E6039 Power on reset occurred 61633 E6040 Parameters have changed 61634 E6041 Mode select parameters have changed 61635 E6042 Log parameters have changed 61636 E6043 Copy cannot execute - host cannot disconnect 61637 E6044 Command sequence error 61638 E6045 Overwrite error on update in place 61639 E6046 Tagged commands cleared by another initiator 61640 E6047 Incompatible medium installed 61641 E6048 Cannot read medium - unknown format 61642 Cannot read - incompatible format 61643 Cleaning cassette is installed 61644 E6049 Medium format is corrupted - DDS bad at group level 61645 E6050 Tape length error - too short to partition 61646 Mode Select round off 61647 E6051 Saving of parameters not supported 61648 No cassette is loaded 61649 E6052 Sequential positioning error 61650 E6053 Tape position error at beginning of media 61651 E6054 Physical end of tape encountered-tape position error at EOM 61652 E6055 Reposition error 61653 E6056 Read past of end of medium 61654 Medium destination element full - changer 61655 Medium source element empty - changer 61656 E6057 Illegal bit set in identify message 61657 E6058 Device has not self configured yet 61658 Target operating conditions have changed 61659 New microcode was loaded 61660 Changed operating definitions 61661 Inquiry data has changed 61662 E6059 Internal ram or diagnostic failure 61663 E6060 Diagnostics failure. Vendor unique 61664 E6061 Unspecified fatal error 61665 E6062 Timeout error 61666 E6063 SCSI Message error 61667 E6064 Internal software (firmware) error 61668 E6065 Unexpected selection interrupt from hardware 61669 E6066 EDC error detected by port 61670 E6067 Select - reselect failure 61671 E6068 Unsuccessful soft reset 61672 E6069 SCSI parity error detected 61673 E6070 Initiator detected error message received 61674 E6071 Invalid message error 61675 E6072 Command phase error 61676 E6073 Data phase error 61677 E6074 Logical unit failed self-configuration 61678 E6075 Overlapped commands attempted 61679 E6076 Write append error 61680 E6077 Write append position error - retry limit exhausted 61681 E6078 Timer position error 61682 E6079 Erase failure 61683 E6080 Cassette fault 61684 E6081 Media load or eject failed 61685 E6082 Unload tape failure 61686 E6083 Media removal prevented 61687 E6084 Drive hardware error - servo or sensor 61688 Operator requested media removal 61689 E6085 Log exception 61690 E6086 Threshold condition met 61691 Log counter at maximum 61692 E6087 Log list codes exhausted 61693 E6088 Mode mismatched fixed - variable 61694 E6089 Excessive dryness 61695 E6090 Mode select failed because the tape is not at LBOT 61696 No Sense 61697 Recovered Error 61698 Not Ready 61699 Medium Error 61700 Hardware Error 61701 Illegal Request 61702 Unit Attention 61703 Media Protect 61704 Blank Check 61705 Vendor Unique 61706 Aborted Command 61707 Filemark 61708 End of media 61709 E6091 Incorrect block length 61710 Reserved 61711 Usually OK 61712 Recoverable error 61713 E6092 Fatal - Uncorrectable error 61714 Tape may be damaged 61715 Tape drive may have malfunctioned 61716 Tape heads should be cleaned 61717 Tape may be damaged or drive may have malfunctioned 61718 Tape may be damaged or drive may have malfunctioned, try head cleaning 61719 Unknown failure 61720 Software Error 61721 E6093 Possible firmware error or catastrophic drive failure 61722 Environmental Conditions 61723 61724 UNKNOWN SENSE VALUE 61725 UNKNOWN ERROR 61726 SEVERITY UNKNOWN 61728 Eject Tape 61729 Power Fail 61730 E6094 SCSI Bus Parity Error 61731 E6095 Formatted Buffer Parity Error 61732 E6096 Media Error 61733 E6097 Error Counter Overflow 61734 E6098 Tape Motion Error 61735 Tape Not Present 61736 Logical Beginning Of Tape 61737 E6099 Transfer Abort Error 61738 E6100 Tape Mark Detect Error 61739 Write Protect 61740 E6101 Filemark Error 61741 E6102 Underrun Error 61742 E6103 Write Error 1 61743 E6104 Servo System Error 61744 E6105 Formatter Error 61745 Physical End Of Tape 61746 E6106 Write Splice Error, Blank 61747 E6107 Write Splice Error, Overshoot 61748 E6108 No error bits are set 61749 E6109 Failed to initialize list. Possibly out of memory. 61751 Tape Engine Message Window 61770 Please Select Cancel when Windows NT prompts to end Tape Server Message Window. Otherwise you will down Tape Engine. Use ARCServe Server Admin to close Tape Server Message Window. 61771 Tape Engine Message Window Warning 61772 E6113 Operation aborted: failed to open %s file '%s' for %s 61773 E6114 No match found for the specified date in the activity log, grooming aborted. 61774 E6115 Operation aborted: failed while writing to file '%s' 61775 File grooming is complete. 61776 Had a system failure while manipulating the activity log file. The file might now be trashed. 61777 Tape Head Cleaning 61778 Press any key to continue 61779 61780 %s 61782 Number of Sessions 61783 MBytes per Session 61784 Test for Throughput 61785 Regular Tape Test Configuration 61786 Full Tape Test Configuration 61787 Press any key to stop test 61788 Rewind 61789 Space Data Blocks 61790 Space Filemarks 61791 Space to EOD 61792 Read Data Blocks 61793 Write Data Blocks 61794 Write Filemark 61795 Read Block Address 61796 Seek Block 61797 Seek Position 61798 Advanced Tape Testing 61799 Parameter Required Functions 61800 Enter the parameter 61801 Raw SCSI Command 61802 Logical/Physical Address 61803 Direction 61804 Command Byte Count 61805 SCSI Command 61806 LUN 61807 Byte 2 61808 Byte 3 61809 Byte 4 61810 Byte 5 61811 Byte 1 61812 A WRITE command was received when the tape was not at a legal position to write. 61813 A WRITE command was received when the data cartridge was write protected. 61814 LEOT was encountered during the current write operation (the command may have terminated early). 61815 The write operation was aborted, as requested. 61816 LEOT was encountered during the last write operation (the command completed successfully). 61817 LEOT was encountered during a read operation. 61818 The actual block size read did not match the requested block size during a read operation. 61819 An uncorrectable block was encountered during a read operation. 61820 EOD was encountered during a read operation. 61821 A filemark was encountered during a read operation. 61822 The EXB-8500 was not in a legal condition to read (in write mode or not ready). 61823 Already at blank tape, so it is an error to attempt a read operation. 61824 The read operation was aborted, as requested. 61825 Too many permanent read errors-can't sync. 61826 PEOT was encountered during a read operation. 61827 An invalid file number was detected in a filemark during a read operation. 61828 A Medium Error was detected during a read operation. 61829 A Hardware Error was detected during a read operation. 61830 The data on the tape is compressed, but the hardware cannot decompress it. (Note: This fault symptom code is include for upward compatibility with products supporting data compression.) 61831 A WRITE FILEMARKS command was received when the tape was not at a legal position to write. 61832 A WRITE FILEMARKS command was received when the data cartridge was write protected. 61833 LEOT was encountered during or before the write filemarks operation-the filemark was written. 61834 A filemark was detected during a space or locate operation. 61835 EOD was encountered during a space or locate operation. 61836 PEOT was encountered during a space or locate operation. 61837 PBOT was encountered during a space or locate operation. 61838 A tape format error was encountered during a space or locate operation. 61839 An uncorrectable block was encountered during a space or locate operation. 61840 A Medium Error was detected during a space or locate operation. 61841 A wrong file number was encountered in a filemark during a space operation (EXB-8200 format tapes only). 61842 The SPACE or LOCATE command was aborted, as requested. 61843 The tape is not a legal place to erase or the EXB-8500 is not ready. 61844 The data cartridge is write protected and cannot be erased. 61845 The ERASE command was aborted, as requested. 61846 An error occurred during the send diagnostics operation. 61847 An error occurred during the send diagnostics operation. 61848 The code header was in the wrong format when loading firmware. 61849 The servo load image was not valid. 61850 Bank 0 of control load image was not valid. 61851 Bank 1 of control load image was not valid. 61852 The EEPROM load image was not valid. 61853 The boot code did not allow a load from tape, or the code version was not supported by the boot code. 61854 One of the memories could not be programmed. 61855 A Hardware Error occurred while loading new firmware. 61856 The CRC in the load image in the buffer was incorrect. 61857 The READ BUFFER command failed. 61858 Controller firmware logic error. 61859 Write failure after retry limit (specified with MODE SELECT) exceeded. 61860 Write filemark failure after internal retry limit exceeded. 61861 Write EOD failure after internal retry limit exceeded. 61862 Hardware failure-Invalid BRT. 61863 Hardware failure-Buffer empty. 61864 Hardware failure-Deformatter Intrp timeout on search. 61865 Hardware failure-Formatter Intrp timeout on write. 61866 Permanent write error-Write recovery failure. 61867 Permanent write error-Rewrite threshold exceeded. 61868 Servo zone read-back-check failure. 61869 Hardware failure-Head sync error during write. 61870 Underrun error during write. 61871 IPORT write buffer parity error. 61872 DPORT write buffer parity error. 61873 PPort write buffer parity error. 61874 IPORT read buffer parity error. 61875 DPORT read buffer parity error. 61876 PPORT read buffer parity error. 61877 Servo timed out. 61878 Servo software error. 61879 Servo hardware failure. 61880 Unable to achieve or maintain tracking. 61881 EOT encountered during a tape motion command. 61882 LBOT write failure- read-back-check criteria not met after retry limit exceeded. 61883 LBOT failure-unable to write tape-mark tracks in EXB-8200 mode. 61884 Physical Read Manager could not read LBOT. 61885 EOT encountered during buffer flush. 61886 Unit Attention-Power-on reset occurred. 61887 Unit Attention-Data cartridge may have been changed. 61888 Unit Attention-MODE SELECT parameters were changed. 61889 Unit Attention-New microcode was loaded. 61890 Unit Attention-Operator requested media removal. 61891 Not Ready-Cause not known. 61892 Not Ready, but becoming ready. 61893 A tape motion command is required to move the tape from its current location. 61894 The command requires a tape, but no tape is loaded. 61895 Parameter List Length error in the MODE SELECT CDB. 61896 Illegal Op Code. 61897 Invalid field or reserved bits set in the CDB. 61898 The LUN is not supported. 61899 Invalid field in Parameter List (MODE SELECT). 61900 The LUN in the Identify message is illegal (not zero). 61901 Media removal is prevented. 61902 A variable/fixed mismatch occurred between the CDB and the MODE SELECT parameters. 61903 Illegal transfer length in CDB. 61904 The command requires no tape, but a tape is loaded (SEND DIAGNOSTICS). 61905 Could not change the MODE SELECT parameters since the tape was not at LBOT. 61906 Cannot read the tape position-Incompatible format. 61907 Overlapped commands attempted-Bad ITL nexus. 61908 Logical block out of range. 61909 Illegal bit set in Identify message. 61910 The command was aborted in the CDB phase- Parity or other error. 61911 The command was aborted before the Data phase- Received bad message. 61912 The command was aborted in the Data phase- Initiator Detected Error message. 61913 The command was aborted in the Data phase- Received bad message out. 61914 The command was aborted after the Data phase- Received bad message out. 61915 The command was aborted after the Data phase- Other error. 61916 The WRITE command was aborted because of a SCSI bus parity error. 61917 The initiator sent an Abort or Initiator Detected Error message during a read operation and the command was aborted. 61918 A WRITE BUFFER command sequencing error occurred. 61919 The EXB-8500's serial number is invalid or blank. 61920 Head sync value in EEPROM is out of range. 61921 The EEPROM contains meaningless information. 61922 Issue a REWIND command. 61923 Issue a SPACE command to space backward over a block or filemark. 61924 Reissue the failed command or command sequence. 61925 Correct the errors in the CDB bytes or parameter data. 61926 Move the write protect switch on the data cartridge to write enable the tape. 61927 Repeat the operation with a new data cartridge. 61928 Insert a data cartridge into the EXB-8500. 61929 Perform one of the following actions: %-30sPower the EXB-8500 off and back on again. %-30sSend a SCSI bus reset ('hard' reset). 61930 Clean the EXB-8500 and repeat the operation. 61931 No action is necessary. 61932 User should determine what recovery procedure to follow. 61933 The EXB-8500 requires maintenance. 61934 (1) Perform one of the following actions:%-30sIssue a REWIND, SPACE, LOAD/UNLOAD, or LOCATE command.%-30sPress the unload button.%-30sPower the EXB-8500 off and back on again.%-30sSend a SCSI bus \nreset.%-25s(2) Reissue the failed command and sequence. 61935 Repeat the operation with a different data cartridge; the EXB-8500 cannot read the tape. 61936 Reprogram the EEPROM. 61944 Function 'print_message()' was called with a NULL pointer or an empty message ! Make sure that file 'TAPEENG.NLM' and 'TAPEENG.MSG' have the same version number. 61945 E6202 Change Tape Failed: %s 61946 Error opening file '%s': %s 61947 E6203 Head Cleaning Failed: %s 61948 E6205 Error opening %s. Error: %s 61949 E6206 Error writing %s. Error: %s 61950 E6204 Rewind Failed: %s 61951 E6200 Regular Tape Test Failed: %s 61952 E6201 Full Tape Test Failed: %s 61957 Memory Allocation Failure 61958 Tape Engine Log File Is Being Groomed 61960 E6500 Client connect to tape failed. 61961 Possible Power-on reset occurred or 61962 possible SCSI-bus reset occurred or 61963 possibly the data cartridge was removed. 61964 E6501 Job denied %s 61965 E6502 Find next session failed 61966 E6503 Start session failed. 61967 E6504 End session failed. 61968 E6505 End job failed. 61969 E6506 Suspend job failed. 61970 NO ERROR / JOB REQUEST GRANTED 61971 DCB ERROR-NO MEMORY 61972 MAXIMUM DEVICES REACHED 61973 BAD DEVICE NUMBER 61974 DEVICE ALREADY OPEN 61975 DEVICE NOT OPEN 61976 DEVICE ALREADY LOCKED 61977 DEVICE NOT LOCKED 61978 BAD DEVICE HANDLE 61979 FAILED TO ALLOCATE WORK BUFFER 61980 ALLOC WRKBUFFER NO MEMORY 61981 TAPE PROCESSES AT ZERO 61982 TAPE PROCESSES AT MAXIMUM 61983 INVALID TAPE DEVICE 61984 CREATE TAPE CONSOLE FAILED 61985 CREATE SCAN DAEMON FAILED 61986 CANNOT LOAD NLM ERROR 61987 CANNOT OPEN LOAD FILE 61988 CANNOT READ LOAD FILE 61989 LOAD FILE ERROR 61990 LOAD FILE DONE 61991 NO COMMAND LINE AVAILABLE 61992 CANNOT SET TAPE BLOCKSIZE 61993 INVALID NLM HANDLE 61994 BAD ENTRY POINT TABLE 61995 ILLEGAL SCSIID 61996 ILLEGAL GROUP NAME 61997 NO DEVICES FOUND 61998 BAD GROUP NUMBER 61999 NON EXISTENT GROUP 62000 NO MEMORY FOR IO BUFFERS 62001 CANNOT ALLOCATE DAEMON LIST BUFFERS 62002 FAILED TO CREATE READ DAEMON 62003 FAILED TO CREATE WRITE DAEMON 62004 NO JOB GIVEN 62005 DEVICE NOT USED 62006 BAD PARAMETER PASSED 62007 JOB DENIED GRP NA 62008 JOB DENIED MAXIMUM JOBS REACHED 62009 JOB DENIED NO MEM 62010 JOB DENIED GRP BSY 62011 JOB DENIED COMM ERROR 62012 JOB DENIED ILLEGAL CLIENT TYPE 62013 JOB DENIED FAILED TO CREATE DAEMON 62014 JOB DENIED ILLEGAL JOB TYPE 62015 BAD JOB HANDLE 62016 DAEMON ALREADY CREATED 62017 INVALID FUNCTION 62018 SECTION PARAMETER NOT FOUND 62019 GROUP NAME ALREADY REGISTERED 62020 DEVICE ALREADY REGISTERED 62021 COMM FAILURE 62022 FAILED TO WRITE VOLUME HEADER 62023 NO MEMORY FOR JCB TABLES 62024 COMPRESSION ERROR ILLEGAL DRIVE TYPE 62025 PADDING ERROR ILLEGAL DRIVE TYPE 62026 NO DEVICES FOUND TO LOCK 62027 NO DEVICES FOUND TO UNLOCK 62028 ERROR WRITE DAEMON SUSPENDED 62029 ERROR READ DAEMON SUSPENDED 62030 ERROR DAEMON ABORTED 62031 ERROR UNKNOWN DAEMON ERROR 62032 ILLEGAL ERASE MODE 62033 INTERMEDIATE PKT 62034 OPEN FAILED SCANNING BUSY 62035 ERROR NO PARAMETERS GIVEN 62036 DAEMON ILLEGAL BUFFERADDRESS 62037 DAEMON BUFFER TOO LARGE 62038 INVALID TAPE DRIVE 62039 TAPE BUSY SEMAPHORE NOT CREATED 62040 TAPE BUSY SEMAPHORE FAILURE 62041 TAPE UNBUSY SEMAPHORE NOT CREATED 62042 TAPE UNBUSY SEMAPHORE FAILURE 62043 TAPE COPY ERROR 62044 TAPE COPY NOSPACELEFT 62045 TAPE MISCOMPARE ERROR 62046 TAPE COMPARE OUTOFSYNC ERROR 62047 TAPE HEADER MISCOMPARE ERROR 62048 TAPE COMPARE GENERAL ERROR 62049 TAPE COPY BUSY 62050 TAPE COMPARE BUSY 62051 DEVICE NOT A TAPE DRIVE 62052 JOB DENIED TAPEENG DISABLED 62053 ERROR DAEMON NOT INITIALIZED 62054 ERROR BOARD VERSION NOT SUPPORTED 62055 ERROR STANDARD SHUTDOWN OCCURRING 62056 REENTRANCY ERROR OPEN DEVICE TIMEOUT 62057 REENTRANCY ERROR CANNOT OPEN MULTIPLE DEVICES 62058 ERROR STARTING NAME OUT OF RANGE 62059 ERROR MEDIA IS BLANK 62060 ERROR BUFFER PASSED IS NULL 62061 ERROR NO MEDIA IN DRIVE 62062 ERROR SYNC READ TOO LARGE 62063 ERROR SYNC WRITE TOO LARGE 62064 ERROR ILLEGAL SHOTS VALUE 62065 ERROR ILLEGAL SCSIID VALUE 62066 ERROR FAILED TAPEENG DEACTIVATE GROUPS ACTIVE 62067 ERROR FAILED GROUP UNLOAD GROUPS ACTIVE 62068 ERROR ILLEGAL BLOCK SIZE VALUE 62069 ERROR UNKNOWN CFG CONDITIONAL 62070 ERROR DEVICE NOT READY 62071 ERROR ILLEGAL SLOTS VALUE 62072 ERROR ALLOCATING CHANGER MEMORY 62073 ERROR BAD NLM SIGNATURE 62074 ERROR MAXIMUM NLMS REACHED 62075 ERROR BAD GROUP SIGNATURE 62076 ERROR MAXIMUM GROUPS REACHED 62077 62078 62079 62080 62081 62082 ERROR FAILED TO REGISTER GROUP INFO 62083 ERROR CONFLICTING DEVICES DETECTED IN GROUP 62084 ERROR NO GROUP NAME GIVEN ON CMDLINE 62085 ERROR ILLEGAL COMMAND LINE PARAMETER 62086 ERROR ILLEGAL SCSIID PARAMETER 62087 ERROR NO SCSIID GIVEN TO PARAMETER 62088 JOB DENIED TAPENAME NOT FOUND 62089 ERROR NO VALID RESIDUE INFO 62090 ERROR QFA CHUNK OFFSET SURPASSED 62091 ERROR QFA ILLEGAL MODE 62092 62093 62094 62095 62096 62097 CTP_COMMUNICATION_FAILURE 62098 CTP TOO MANY BLOCKS 62099 CTP NO MEMORY 62100 CTP OFFSET TOO BIG 62101 CTP INVALID COMMAND 62102 ERROR VALIDATE NLM NOT LOADED 62103 ERROR MISSING BOARD ENTRY POINT 62104 ERROR BCB TABLES FULL 62105 ERROR BCB DUPLICATE NAME FOUND 62106 ERROR BCB BOARD NUMBER OUT OF RANGE 62107 ERROR DAEMON BUFFERSIZE OUT OF RANGE 62108 ERROR ILLEGAL BUFFERSIZE GIVEN 62109 ERROR BAD DELIMITER GIVEN 62110 ERROR NO BOARD DRIVER NAME GIVEN 62111 ERROR BOARD NAME NOT FOUND IN LIST 62112 ERROR TAPECAPACITY NOT SUPPORTED 62113 ERROR BOARD DOES NOT EXIST 62114 ERROR TAPEENG ALREADY DEACTIVATED 62115 ERROR GETTING NLM HANDLE 62116 ERROR FAILED TO REGISTER DOWN EVENT 62117 ERROR COPY FAILED DRIVES NOT SAME 62118 ERROR COMPARE FAILED DRIVES NOT SAME 62119 JOB DENIED VOLUME HEADER ILLEGAL BLOCK LENGTH 62120 ERROR TAPE COPY MEDIUM ERROR ON SOURCE 62121 ERROR TAPE COPY HARDWARE ERROR ON SOURCE 62122 ERROR TAPE COPY NO TAPE IN SOURCE DRIVE 62123 ERROR TAPE COPY UNIT ATTENTION ON SOURCE 62124 ERROR TAPE COPY MEDIUM ERROR ON DESTINATION 62125 ERROR TAPE COPY HARDWARE ERROR ON DESTINATION 62126 ERROR TAPE COPY NO TAPE IN DESTINATION DRIVE 62127 ERROR TAPE COPY UNIT ATTENTION ON DESTINATION 62128 ERROR TAPE COPY CANNOT CREATE COPY DAEMONS 62129 ERROR TAPE COMPARE MEDIUM ERROR ON SOURCE 62130 NO ERROR 62131 ILLEGAL COMMAND 62132 END OF MEDIA 62133 FILEMARK DETECTED 62134 NO DATA DETECTED 62135 UNRECOVERABLE DATA ERROR 62136 CARTRIDGE NOT IN PLACE 62137 HARDWARE ERROR 62138 WRITE PROTECTED 62139 TAPE AT BEGINNING OF MEDIA 62140 TAPE AT EARLY WARNING 62141 UNIT ATTENTION DETECTED 62142 COPY ABORTED 62143 COMMAND ABORTED 62144 ILLEGAL BLOCK SIZE 62145 RESERVATION CONFLICT 62146 SCSI BUSY 62147 ERROR TAPE COMPARE HARDWARE ERROR ON SOURCE 62148 ERROR TAPE COMPARE NO TAPE IN SOURCE DRIVE 62149 ERROR TAPE COMPARE UNIT ATTENTION ON SOURCE 62150 ERROR TAPE COMPARE MEDIUM ERROR ON DESTINATION 62151 ERROR TAPE COMPARE HARDWARE ERROR ON DESTINATION 62152 ERROR TAPE COMPARE NO TAPE IN DESTINATION DRIVE 62153 ERROR TAPE COMPARE UNIT ATTENTION ON DESTINATION 62154 ERROR TAPE COMPARE BLOCK COUNT DIFFER 62155 ERROR TAPE COMPARE FILEMARKS OUT OF SYNC 62156 ERROR TAPE COPY ZERO BLOCKS READ SOURCE 62157 ERROR TAPE COPY NO SPACE LEFT ON DESTINATION 62158 ERROR FAILED TO CREATE GROUPBSY SEMAPHORE 62159 TAPE TEST COMPARE ERROR 62174 Return To Tape Engine 62175 Changer Options 62176 View Tapes/Tape Info 62177 Change Loaded Tape 62178 Auto Pilot Prepare/Erase 62179 Format Magazine 62180 Dismount Magazine 62181 Mount Magazine 62182 Export Tape 62183 Tape Drive Head Cleaning 62184 Import Tape 62187 Changer Information 62218 %sΩ Date: %sΩ Time: %sΩ Seq #: %s Ω Drive: %s (2.2 GB)Ω Format: %sΩ 62219 %sΩ Date: %sΩ Time: %sΩ Seq #: %s PermanentΩ Drive: %s (2.2 GB)Ω Format: %sΩ 62220 %sΩ Date: %sΩ Time: %sΩ Seq #: %s Ω Drive: %s (5.0 GB)Ω Format: %sΩ 62221 %sΩ Date: %sΩ Time: %sΩ Seq #: %s PermanentΩ Drive: %s (5.0 GB)Ω Format: %sΩ 62222 %sΩ Date: %sΩ Time: %sΩ Seq #: %s Ω Drive: %s (2.0 GB)Ω Format: %sΩ 62223 %sΩ Date: %sΩ Time: %sΩ Seq #: %s PermanentΩ Drive: %s (2.0 GB)Ω Format: %sΩ 62282 E6901:Memory allocation error. 62283 E6902:Failed to allocate memory for SpxListenForConnection 62284 E6911:Failed to Open Socket, %x 62285 E6912:SpxListenForConnection() ret:%x (%d ECB's) 62286 E6940:[%x] Invalid SPX connection 62287 E6941:[%x] Receive Error [%x] 62288 E6943:[%x] Transmit timeout 62289 E6944:[%x] Previous asynch transmit ECB status=%x 62290 E6945:[%x] Error sending packet=%x 62291 E6946:[%x] Previous transmit ECB status=%x 62292 E6947:[%x] Transmit timeout 62293 E6903:Memory allocation failed at ReadVolumeTable(). 62294 E6921:[%x] Span buffer not filled. 62295 E6904:malloc error in PWriteBlockSync 62296 E6905:malloc error in PReadBlock. 62297 E6906:malloc error in PReadBlockSync. 62298 E6913:[%x] Transmit error in ReadBlockSync: %x 62300 Getting info on Changer-Device %d lun %d 62301 Non-Supported Changer Detected... 62302 Changer %24.24s Detected. 62303 Number of storage elements is %d 62304 ReadChangerElementStatus() ret = %x 62305 Mounting magazine... 62306 ResetChanger() ret = %x 62307 Reading all tapes in magazine. 62308 ReadAllChangerTapes() ret = %x 62309 Cartridge in slot #%d is not present 62310 Failed to unload tape. Error: %x. 62311 Changer door has been opened. 62312 Changer Failure: Mechanical positioning error. 62313 Changer Failure: Internal target failure. 62314 Changer Failure: Configuration. 62315 Changer Failure: Media load-eject failure. 62316 Changer, Power on reset has occurred. 62317 Changer Failure: Other - %x %x %x. 62318 Changer, Unit Attention/Not ready not cleared after 10 retries. Returning. 62319 Changer CANNOT be initialized in this state. Check equipment. 62320 Changer CANNOT be initialized in this state. Close door to initialize 62321 Changer, Proceeding with initialization. 62322 Changer, Still not ready, retrying. 62323 Dismount Magazine Failed: %x. 62324 Dismount Magazine Successful 62325 Mount Magazine Failed: %x. 62326 Mount Magazine Successful 62327 ASDBGetTapeInfo failed: [%x] 62328 Tape is not labeled. 62329 WARNING - There may be a synchronization problem between the Tape Engine and the Database Engine. 62330 Tape: %-24.24s ID: %4.4s Seq: %2d is expired. 62331 Change Loaded Tape Failed: %x. 62332 Change Loaded Tape Successful 62333 Insert Cleaning Cartridge Failed: %x. 62334 Insert Cleaning Cartridge Successful 62335 Removing cleaning cartridge Failed: %x. 62336 Removing cleaning catridge Successful. 62337 Client Export Tape Failed: %x. 62338 Client Export Tape Successful 62339 Client Import Tape Failed: %x. 62340 Client Import Tape Successful 62341 Change new element Failed: %x. 62342 Erase Tape Failed: %x. 62343 Format Tape Failed: %x. 62344 Device Initialization Failure %s - Unloading required 62345 Regular Tape Test Successful 62346 Full Tape Test Successful 62347 %s Successful 62348 You have overridden the device check for copy. 62349 Please remove the currently loaded tape... 62350 Failed to ASDB update head cleaning. [%x] 62351 Tape is not in %s Database. 62352 The following is recorded in the Database. 62353 DEVICE INITIALIZATION FAILURE - %s 62354 No groups are configured 62355 Unloading group %s 62356 Group Unload 62357 Tape Tests will DESTROY all data on tape. Continue? 62358 Tape Drive does not support compression. 62359 Tape must be blank or erased to change compression. 62360 Tape Name and Expiration Date MUST be completed. 62361 Please insert the cleaning cassette... 62362 Please wait until the cleaning cartridge is ejected... 62363 Press any key when this is complete... 62364 Tape Drive Compression Mode is currently %s 62365 Setting Compression %s 62366 Setting Compression %s for device %d 62367 %s Version 4.0 / 5.0 Compatible 62368 %s Version 5.0 Compatible 62369 Tape Manager 5.01 62383 MEDIUM TRANSPORT 62384 STORAGE ELEMENT 62385 IMPORT EXPORT 62386 DATA TRANSFER 62387 Length: %d Block Desc Len: %d Page Code: %x PL: %d 62388 Changer: Rezero failed: %x %x %x 62389 Move Medium %d to %d - deviceHandle %x 62390 Changer: Move Medium failed: %x %x %x 62391 ChangeNewElement(%d) 62392 Doing unload from - changenewele 62393 Removing tape %d from tape 62394 Error Unloading tape: %x 62395 Current_tape_in_drive = %d 62396 Now Moving tape %d into tape 62397 cartridge_array[%d] = %d tape in drive = %d 62398 Slot: %d contains no tape. 62399 Moving tape %d into tape 62400 Error moving media: %x 62401 Error loading tape: %x 62402 Tape Name: %24.24s ID: %x Seq: %d 62403 Tape Name: ** BLANK TAPE ** 62404 Removing tape %d from tape - read_stacker 62405 Doing unload from - read_stacker 62406 Read element Status %x 62407 \n devH: %x lun: %x elty: %d stEl: %d numEl: %d bufs: %d 62408 Error on ChangerReadElementStatus: %x 62409 Start info on %s... 62410 Element Status Data header y = %d 62411 Medium Transport header y = %d 62412 Medium Transport descriptor y = %d 62413 MEDIUM_TRANSPORT_INDEX = %d 62414 Storage Element header y = %d 62415 Storage Element descriptor byteCount = %d x = %d 62416 STORAGE_ELEMENT_INDEX + x = %d 62417 Import Element header y = %d 62418 Import descriptor y = %d 62419 IMPORT_EXPORT_INDEX = %d 62420 Data Transfer Element header y = %d 62421 Data Transfer descriptor byteCount = %d x = %d 62422 DATA_TRANSFER_INDEX + x = %d 62423 Number of elements reported: %d 62424 Element Status Page and Descriptor Headers 62425 Element Type: %d DLength: %d DbyteCount: %d 62426 All elements... 62427 Tape in drive: %d 62428 Tape in drive is from slot %d 62429 %d cartridges in magazine, %d in tape drive, total %d 62430 Magazine Status (Full or Empty) 62431 Slot %d is %s 62432 Full 62433 Empty 62434 Unloading loaded tape... 62435 Cartridge %d in tape 62436 Moving tape %d back to magazine 62437 Special test unit ready for door open/closed - deviceH %x 62438 Still not ready, retrying. 62439 Becoming ready. 62440 Changer door has been closed, reinitializing. 62441 Changer door has been opened. 62442 Changer Failure: Internal target failure. 62443 Changer Failure: component %d. 62444 Manual Intervention is required. 62445 ChangeNewElement failed: %x 62446 MEDIA TRANSPORT 62447 IMPORT/EXPORT 62448 DATA TRANSFER 62449 STORAGE ELEMENT 62450 \nFailed to open %s\n 62451 \nFailed to update %s\n 62452 Failed to open %s 62453 Timeout Error. 62454 Error code %04x 62455 Spawn Error code %04x 62456 \nError reading %s file. \n 62457 %s is loaded.\n 62458 System Console 62459 Cancel all jobs or deactivate %s before unloading. 62460 Tapeeng cannot be unloaded because jobs are active. 62461 Unloading %s is in progress...\n 62462 %s is unloaded.\n 62463 Engine is being DOWNed, %s will shut down...\n 62464 The %d%s byte of MODE SELECT is invalid 62465 Unknown Fault Symptom Code: (%02X) 62466 Error Writing to Non-Data Grade Tape. 62467 This tape may only be used for restore operations. 62468 TAPEENG: Unable to open %s - [%x/%x]\n 62469 Sess: %d - Usage: %d secs - BytesWritten: %d KB 62470 [Early Warning] Recovered %s Errors: %d for group %-8.8s 62471 Read 62472 Write 62473 [Early Warning] Sess: %d - Usage: %d secs - BytesWritten: %d KB 62474 Device %-8.8s on ID %d - %d recovered %s errors 62475 Read 62476 Write 62477 Device %-8.8s on ID %d 62478 Has no support for recovered error counts. 62479 Error allocating memory for view. 62480 TAPE$SVR.LOG file wasn't be groomed because no logging 62481 Exabyte suggested error recovery procedure: 62716 E6900 SCSI Timeout: Bus free phase timeout 62717 E6901 SCSI Timeout: Selection phase timeout 62718 E6902 SCSI Timeout: Command phase timeout 62719 E6903 SCSI Timeout: Data phase timeout 62720 E6904 SCSI Timeout: Status phase timeout 62721 E6905 SCSI Timeout: Message phase timeout 62722 E6906 SCSI Error: Parity Error 62723 E6907 SCSI Error: Lost busy signal Error 62724 E6908 SCSI Error: Invalid phase detected Error 62725 E6909 SCSI Error: Unknown Error 62726 E6910 SCSI Timeout: General timeout Error 62727 E6911 SCSI Error: Reentrancy Error 62728 E6912 SCSI Error: Invalid request Error 62729 E6913 SCSI Error: SCSI reset detected Error 62730 E6914 SCSI Error: Error locating adapter Error 62731 E6999 Unknown Error Code: %d 62817 Tape Engine is Started. 62818 Tape Engine is Stopped. 62819 Tape Engine received a backup job request. 62820 Tape Engine is done with the backup job. 62821 Tape Engine received a restore job request. 62822 Tape Engine is done with the restore job. 62823 Tape Engine finished formatting tape.(new name: %s, old name: %s) 62824 Tape Engine finished erasing tape.(old name: %s) 62825 Tape Engine - Critical Error!!!! Daemon is terminated!! 62826 Device added to group 62827 Groups reconfigured 62828 New Changer Group has been created 62829 Starting dynamic grouping 62830 Dynamic grouping info updated 62831 Dynamic grouping canceled 62832 Group Deleted 62833 Group Renamed 62834 Group Created 62835 Incomplete session, Attempting to repair.. 62836 Session Repaired Successfully