Network Working Group A. Malis Request for Comments: 1356 BBN Communications Obsoletes: RFC 877 D. Robinson Computervision Systems Integration R. Ullmann Process Software Corporation August 1992
Multiprotocol Interconnect on X.25 and ISDN in the Packet Mode
Status of this Memo
This RFC specifies an IAB standards track protocol for the Internet community, and requests discussion and suggestions for improvements. Please refer to the current edition of the "IAB Official Protocol Standards" for the standardization state and status of this protocol. Distribution of this memo is unlimited.
Abstract
This document specifies the encapsulation of IP and other network layer protocols over X.25 networks, in accordance and alignment with ISO/IEC and CCITT standards. It is a replacement for RFC 877, "A Standard for the Transmission of IP Datagrams Over Public Data Networks" [1].
It was written to correct several ambiguities in the Internet Standard for IP/X.25 (RFC 877), to align it with ISO/IEC standards that have been written following RFC 877, to allow interoperable multiprotocol operation between routers and bridges over X.25, and to add some additional remarks based upon practical experience with the specification over the 8 years since that RFC.
The substantive change to the IP encapsulation is an increase in the allowed IP datagram Maximum Transmission Unit from 576 to 1600, to reflect existing practice.
This document also specifies the Internet encapsulation for protocols, including IP, on the packet mode of the ISDN. It applies to the use of Internet protocols on the ISDN in the circuit mode only when the circuit is established as an end-to-end X.25 connection.
Malis, Robinson, & Ullmann [Page 1]
RFC 1356 Multiprotocol Interconnect on X.25 August 1992
Acknowledgements
RFC 877 was written by J. T. Korb of Purdue University, and this document follows that RFC's format and builds upon its text as appropriate. This document was produced under the auspices of the IP over Large Public Data Networks Working Group of the IETF.
1. Conventions
The following language conventions are used in the items of specification in this document:
o MUST -- the item is an absolute requirement of the specification. MUST is only used where it is actually required for interoperation, not to try to impose a particular method on implementors where not required for interoperability.
o SHOULD -- the item should be followed for all but exceptional circumstances.
o MAY or optional -- the item is truly optional and may be followed or ignored according to the needs of the implementor.
The words "should" and "may" are also used, in lower case, in their more ordinary senses.
2. Introduction
RFC 877 was written to document the method CSNET and the VAN Gateway had adopted to transmit IP datagrams over X.25 networks. Its success is evident in its current wide use and the inclusion of its IP protocol identifier in ISO/IEC TR 9577, "Protocol Identification in the Network Layer" [2], which is administered by ISO/IEC and CCITT.
However, due to changes in the scope of X.25 and the protocols that it can carry, several inadequacies have become evident in the RFC, especially in the areas of IP datagram Maximum Transmission Unit (MTU) size, X.25 maximum data packet size, virtual circuit management, and the interoperable encapsulation, over X.25, of protocols other than IP between multiprotocol routers and bridges.
As with RFC 877, one or more X.25 virtual circuits are opened on demand when datagrams arrive at the network interface for transmission. A virtual circuit is closed after some period of inactivity (the length of the period depends on the cost associated with an open virtual circuit). A virtual circuit may also be closed if the interface runs out of virtual circuits.
Malis, Robinson, & Ullmann [Page 2]
RFC 1356 Multiprotocol Interconnect on X.25 August 1992
3. Standards
3.1 Protocol Data Units (PDUs) are sent as X.25 "complete packet sequences". That is, PDUs begin on X.25 data packet boundaries and the M bit ("more data") is used to fragment PDUs that are larger than one X.25 data packet in length.
In the IP encapsulation the PDU is the IP datagram.
3.2 The first octet in the Call User Data (CUD) Field (the first data octet in the Call Request packet) is used for protocol demultiplexing, in accordance with the Subsequent Protocol Identifier (SPI) in ISO/IEC TR 9577. This field contains a one- octet Network Layer Protocol Identifier (NLPID), which identifies the network layer protocol encapsulated over the X.25 virtual circuit. The CUD field MAY contain more than one octet of information, and receivers MUST ignore all extraneous octets in the field.
In the following discussion, the most significant digit of the binary numbers is left-most.
For the Internet community, the NLPID has four relevant values:
The value hex CC (binary 11001100, decimal 204) is IP [6]. Conformance with this specification requires that IP be supported. See section 5.1 for a diagram of the packet formats.
The value hex 81 (binary 10000001, decimal 129) identifies ISO/IEC 8473 (CLNP) [4]. ISO/IEC TR 9577 specifically allows other ISO/IEC connectionless-protocol packets, such as ES-IS and IS-IS, to also be carried on the same virtual circuit as CLNP. Conformance with this specification does not require that CLNP be supported. See section 5.2 for a diagram of the packet formats.
The value hex 82 (binary 10000010, decimal 130) is used specifically for ISO/IEC 9542 (ES-IS) [5]. If there is already a circuit open to carry CLNP, then it is not necessary to open a second circuit to carry ES-IS. Conformance with this specification does not require that ES-IS be supported.
The value hex 80 (binary 10000000, decimal 128) identifies the use of IEEE Subnetwork Access Protocol (SNAP) [3] to further encapsulate and identify a single network-layer protocol. The SNAP-encapsulated protocol is identified by including a five-octet SNAP header in the Call Request CUD field immediately following the hex 80 octet. SNAP headers are not included in the subsequent X.25 data packets. Only one SNAP-encapsulated protocol may be carried over a virtual circuit
Malis, Robinson, & Ullmann [Page 3]
RFC 1356 Multiprotocol Interconnect on X.25 August 1992
opened using this encoding. The receiver SHOULD accept the incoming call only if it can support the particular SNAP-identified protocol. Conformance with this specification does not require that this SNAP encoding be supported. See section 5.3 for a diagram of the packet formats.
The value hex 00 (binary 00000000, decimal 0) identifies the Null encapsulation, used to multiplex multiple network layer protocols over the same circuit. This encoding is further discussed in section 3.3 below.
The "Assigned Numbers" RFC [7] contains one other non-CCITT and non-ISO/IEC value that has been in active use for Internet X.25 encapsulation identification, namely hex C5 (binary 11000101, decimal 197) for Blacker X.25. This value MAY continue to be used, but only by prior preconfiguration of the sending and receiving X.25 interfaces to support this value. The value hex CD (binary 11001101, decimal 205), listed in "Assigned Numbers" for "ISO-IP", is also used by Blacker and also can only be used by prior preconfiguration of the sending and receiving X.25 interfaces.
Each system MUST only accept calls for protocols it can process; every Internet system MUST be able to accept the CC encapsulation for IP datagrams. A system MUST NOT accept calls, and then immediately clear them. Accepting the call indicates to the calling system that the protocol encapsulation is supported; on some networks, a call accepted and cleared is charged, while a call cleared in the request state is not charged.
Systems that support NLPIDs other than hex CC (for IP) SHOULD allow their use to be configured on a per-peer address basis. The use of hex CC (for IP) MUST always be allowed between peers and cannot be configured.
3.3 The NLPID encodings discussed in section 3.2 only allow a single network layer protocol to be sent over a circuit. The Null encapsulation, identified by a NLPID encoding of hex 00, is used in order to multiplex multiple network layer protocols over one circuit.
When the Null encapsulation is used, each X.25 complete packet sequence sent on the circuit begins with a one-octet NLPID, which identifies the network layer protocol data unit contained only in that particular complete packet sequence. Further, if the SNAP NLPID (hex 80) is used, then the NLPID octet is immediately followed by the five-octet SNAP header, which is then immediately followed by the encapsulated PDU. The encapsulated network layer protocol MAY differ from one complete packet sequence to the next over the same
Malis, Robinson, & Ullmann [Page 4]
RFC 1356 Multiprotocol Interconnect on X.25 August 1992
circuit.
When a receiver is presented with an Incoming Call identifying the Null encapsulation, the receiver MUST accept the call if it supports the Null encapsulation for any network layer protocol. The receiver MAY then silently discard a multiplexed PDU if it cannot support that particular encapsulated protocol. See section 5.4 for a diagram of the packet formats.
Use of the single network layer protocol circuits described in section 3.2 is more efficient in terms of bandwidth if only a limited number of protocols are supported by a system. It also allows each system to determine exactly which protocols are supported by its communicating partner. Other advantages include being able to use X.25 accounting to detail each protocol and different quality of service or flow control windows for different protocols.
The Null encapsulation, for multiplexing, is useful when a system, for any reason (such as implementation restrictions or network cost considerations), may only open a limited number of virtual circuits simultaneously. This is the method most likely to be used by a multiprotocol router, to avoid using an unreasonable number of virtual circuits.
If performing IEEE 802.1d bridging across X.25 is desired, then the Null encapsulation MUST be used. See section 4.2 for a further discussion.
Conformance with this specification does not require that the Null encapsulation be supported.
Systems that support the Null encapsulation SHOULD allow its use to be configured on a per-peer address basis.
3.4 For compatibility with existing practice, and RFC 877 systems, IP datagrams MUST, by default, be encapsulated on a virtual circuit opened with the CC CUD.
Implementations MAY also support up to three other possible encapsulations of IP:
o IP may be contained in multiplexed data packets on a circuit using the Null (multiplexed) encapsulation. Such data packets are identified by a NLPID of hex CC.
o IP may be encapsulated within the SNAP encapsulation on a circuit. This encapsulation is identified by containing, in the 5-octet SNAP
Malis, Robinson, & Ullmann [Page 5]
RFC 1356 Multiprotocol Interconnect on X.25 August 1992
header, an Organizationally Unique Identifier (OUI) of hex 00-00-00 and Protocol Identifier (PID) of hex 08-00.
o On a circuit using the Null encapsulation, IP may be contained within the SNAP encapsulation of IP in multiplexed data packets.
If an implementation supports the SNAP, multiplexed, and/or multiplexed SNAP encapsulations, then it MUST accept the encoding of IP within the supported encapsulation(s), MAY send IP using those encapsulation(s), and MUST allow the IP encapsulation to send to be configured on a per-peer address basis.
3.5 The negotiable facilities of X.25 MAY be used (e.g., packet and window size negotiation). Since PDUs are sent as complete packet sequences, any maximum X.25 data packet size MAY be configured or negotiated between systems and their network service providers. See section 4.5 for a discussion of maximum X.25 data packet size and network performance.
There is no implied relationship between PDU size and X.25 packet size (i.e., the method of setting IP MTU based on X.25 packet size in RFC 877 is not used).
3.6 Every system MUST be able to receive and transmit PDUs up to at least 1600 octets in length.
For compatibility with existing practice, as well as interoperability with RFC 877 systems, the default transmit MTU for IP datagrams SHOULD default to 1500, and MUST be configurable in at least the range 576 to 1600.
This is done with a view toward a standard default IP MTU of 1500, used on both local and wide area networks with no fragmentation at routers. Actually redefining the IP default MTU is, of course, outside the scope of this specification.
The PDU size (e.g., IP MTU) MUST be configurable, on at least a per-interface basis. The maximum transmitted PDU length SHOULD be configurable on a per-peer basis, and MAY be configurable on a per- encapsulation basis as well. Note that the ability to configure to send IP datagrams with an MTU of 576 octets and to receive IP datagrams of 1600 octets is essential to interoperate with existing implementations of RFC 877 and implementations of this specification.
Note that on circuits using the Null (multiplexed) encapsulation, when IP packets are encapsulated using the NLPID of hex CC, then the default IP MTU of 1500 implies a PDU size of 1501; a PDU size of
Malis, Robinson, & Ullmann [Page 6]
RFC 1356 Multiprotocol Interconnect on X.25 August 1992
1600 implies an IP MTU of 1599. When IP packets are encapsulated using the NLPID of hex 80 followed by the SNAP header for IP, then the default IP MTU of 1500 implies a PDU size of 1506; a PDU size of 1600 implies an IP MTU of 1594.
Of course, an implementation MAY support a maximum PDU size larger than 1600 octets. In particular, there is no limit to the size that may be used when explicitly configured by communicating peers.
3.7 Each ISO/IEC TR 9577 encapsulation (e.g., IP, CLNP, and SNAP) requires a separate virtual circuit between systems. In addition, multiple virtual circuits for a single encapsulation MAY be used between systems, to, for example, increase throughput (see notes in section 4.5).
Receivers SHOULD accept multiple incoming calls with the same encapsulation from a single system. Having done so, receivers MUST then accept incoming PDUs on the additional circuit(s), and SHOULD transmit on the additional circuits.
Shedding load by refusing additional calls for the same encapsulation with a X.25 diagnostic of 0 (DTE clearing) is correct practice, as is shortening inactivity timers to try to clear circuits.
Receivers MUST NOT accept the incoming call, only to close the circuit or ignore PDUs from the circuit.
Because opening multiple virtual circuits specifying the same encapsulation is specifically allowed, algorithms to prevent virtual circuit call collision, such as the one found in section 8.4.3.5 of ISO/IEC 8473 [4], MUST NOT be implemented.
While allowing multiple virtual circuits for a single protocol is specifically desired and allowed, implementations MAY choose (by configuration) to permit only a single circuit for some protocols to some destinations. Only in such a case, if a colliding incoming call is received while a call request is pending, the incoming call shall be rejected. Note that this may result in a failure to establish a connection. In such a case, each system shall wait at least a configurable collision retry time before retrying. Adding a random increment, with exponential backoff if necessary, is recommended.
3.8 Either system MAY close a virtual circuit. If the virtual circuit is closed or reset while a datagram is being transmitted, the datagram is lost. Systems SHOULD be able to configure a minimum holding time for circuits to remain open as long as the endpoints
Malis, Robinson, & Ullmann [Page 7]
RFC 1356 Multiprotocol Interconnect on X.25 August 1992
are up. (Note that holding time, the time the circuit has been open, differs from idle time.)
3.9 Each system MUST use an inactivity timer to clear virtual circuits that are idle for some period of time. Some X.25 networks, including the ISDN under present tariffs in most areas, charge for virtual circuit holding time. Even where they do not, the resource SHOULD be released when idle. The timer SHOULD be configurable; a timer value of "infinite" is acceptable when explicitly configured. The default SHOULD be a small number of minutes. For IP, a reasonable default is 90 seconds.
3.10 Systems SHOULD allow calls from unconfigured calling addresses (presumably not collect calls, however); this SHOULD be a configuration option. A system accepting such a call will, of course, not transmit on that virtual circuit if it cannot determine the protocol (e.g., IP) address of the caller. As an example, on the DDN this is not a restriction because IP addresses can be determined algorithmically based upon the caller's X.121 address [7,9].
Allowing such calls helps work around various "helpful" address translations done by the network(s), as well as allowing experimentation with various address resolution protocols.
3.11 Systems SHOULD use a configurable hold-down timer to prevent calls to failed destinations from being immediately retried.
3.12 X.25 implementations MUST minimally support the following features in order to conform with this specification: call setup and clearing and complete packet sequences. For better performance and/or interoperability, X.25 implementations SHOULD also support: extended frame and/or packet sequence numbering, flow control parameter negotiation, and reverse charging.
3.13 The following X.25 features MUST NOT be used: interrupt packets and the Q bit (indicating qualified data). Other X.25 features not explicitly discussed in this document, such as fast select and the D bit (indicating end-to-end significance) SHOULD NOT be used.
Use of the D bit will interfere with use of the M bit (more data sequences) required for identification of PDUs. In particular, as subscription to the D bit modification facility (X.25-1988, section 3.3) will prevent proper operation, this user facility MUST NOT be subscribed.
3.14 ISO/IEC 8208 [11] defines the clearing diagnostic code 249 to signify that a requested protocol is not supported. Systems MAY
Malis, Robinson, & Ullmann [Page 8]
RFC 1356 Multiprotocol Interconnect on X.25 August 1992
use this diagnostic code when clearing an incoming call because the identified protocol is not supported. Non-8208 systems more typically use a diagnostic code of 0 for this function. Supplying a diagnostic code is not mandatory, but when it is supplied for this reason, it MUST be either of these two values.
4. General Remarks
The following remarks are not specifications or requirements for implementations, but provide developers and users with guidelines and the results of operational experience with RFC 877.
4.1 Protocols above the network layer, such as TCP or TP4, do not affect this standard. In particular, no attempt is made to open X.25 virtual circuits corresponding to TCP or TP4 connections.
4.2 Both the circuit and multiplexed encapsulations of SNAP may be used to contain any SNAP encapsulated protocol. In particular, this includes using an OUI of 00-00-00 and the two octets of PID containing an Ethertype [7], or using IEEE 802.1's OUI of hex 00- 80-C2 with the bridging PIDs listed in RFC 1294, "Multiprotocol Interconnect over Frame Relay" [8]. Note that IEEE 802.1d bridging can only be performed over a circuit using the Null (multiplexed) encapsulation of SNAP, because of the necessity of preserving the order of PDUs (including 802.1d Bridged PDUs) using different SNAP headers.
4.3 Experience has shown that there are X.25 implementations that will assign calls with CC CUD to the X.29 PAD (remote login) facility when the IP layer is not installed, not configured properly, or not operating (indeed, they assume that ALL calls for unconfigured or unbound X.25 protocol IDs are for X.29 PAD sessions). Call originators can detect that this has occurred at the receiver if the originator receives any X.25 data packets with the Q bit set, especially if the first octet of these packets is hex 02, 04, or 06 (X.29 PAD parameter commands). In this case, the originator should clear the call, and log the occurrence so that the misconfigured X.25 address can be corrected. It may be useful to also use the hold-down timer (see section 3.11) to prevent further attempts for some period of time.
4.4 It is often assumed that a larger X.25 data packet size will result in increased performance. This is not necessarily true: in typical X.25 networks it will actually decrease performance.
Many, if not most, X.25 networks completely store X.25 data packets in each switch before forwarding them. If the X.25 network requires a path through a number of switches, and low-speed trunks are used,
Malis, Robinson, & Ullmann [Page 9]
RFC 1356 Multiprotocol Interconnect on X.25 August 1992
then negotiating and using large X.25 data packets could result in large transit delays through the X.25 network as a result of the time required to clock the data packets over each low-speed trunk. If a small end-to-end window size is also used, this may also adversely affect the end-to-end throughput of the X.25 circuit. For this reason, segmenting large IP datagrams in the X.25 layer into complete packet sequences of smaller X.25 data packets allows a greater amount of pipelining through the X.25 switches, with subsequent improvements in end-to-end throughput.
Large X.25 data packet size combined with slow (e.g., 9.6Kbps) physical circuits will also increase individual packet latency for other virtual circuits on the same path; this may cause unacceptable effects on, for example, X.29 connections.
This discussion is further complicated by the fact that X.25 networks are free to internally combine or split X.25 data packets as long as the complete packet sequence is preserved.
The optimum X.25 data packet size is, therefore, dependent on the network, and is not necessarily the largest size offered by that network.
4.5 Another method of increasing performance is to open multiple virtual circuits to the same destination, specifying the same CUD. Like packet size, this is not always the best method.
When the throughput limitation is due to X.25 window size, opening multiple circuits effectively multiplies the window, and may increase performance.
However, opening multiple circuits also competes more effectively for the physical path, by taking more shares of the available bandwidth. While this may be desirable to the user of the encapsulation, it may be somewhat less desirable to the other users of the path.
Opening multiple circuits may also cause datagram sequencing and reordering problems in end systems with limited buffering (e.g., at the TCP level, receiving segments out of order, when a single circuit would have delivered them in order). This will only affect performance, not correctness of operation.
Opening multiple circuits may also increase the cost of delivering datagrams across a public data network.
Malis, Robinson, & Ullmann [Page 10]
RFC 1356 Multiprotocol Interconnect on X.25 August 1992
4.6 This document does not specify any method of dynamic IP to X.25 (or X.121) address resolution. The problem is left for further study.
Typical present-day implementations use static tables of varying kinds, or an algorithmic transformation between IP and X.121 addresses [7,9]. There are proposals for other methods. In particular, RFC 1183 [10] describes Domain Name System (DNS) resource records that may be useful either for automatic resolution or for maintenance of static tables. Use of these method(s) is entirely experimental at this time.
5. Packet Formats
For each protocol encoding, the diagrams outline the call request and the data packet format. The data packet shown is the first of a complete packet (M bit) sequence.
5.1 IP Encapsulation
Call Request:
+----------------+-----------+------------+----+ | GFI, LCN, type | addresses | facilities | CC | +----------------+-----------+------------+----+
X.25 data packets:
+----------------+------------------------+ | GFI, LCN, I | IP datagram | +----------------+------------------------+
+----------------+-------------------------------------+ | GFI, LCN, I | Protocol Data Unit (no SNAP header) | +----------------+-------------------------------------+
+----------------+-----------------+---------------------+ | GFI, LCN, I | NLPID (1 octet) | Protocol Data Unit | +----------------+-----------------+---------------------+
Examples of data packets:
Multiplexed IP datagram:
+----------------+----+-----------------------+ | GFI, LCN, I | CC | IP datagram | +----------------+----+-----------------------+
+----------------+----+-----------------+--------------------+ | GFI, LCN, I | 80 | SNAP (5 octets) | Protocol Data Unit | +----------------+----+-----------------+--------------------+
Malis, Robinson, & Ullmann [Page 12]
RFC 1356 Multiprotocol Interconnect on X.25 August 1992
6. Security Considerations
Security issues are not discussed in this memo.
7. References
[1] Korb, J., "A Standard for the Transmission of IP Datagrams Over Public Data Networks", RFC 877, Purdue University, September 1983.
[2] ISO/IEC TR 9577, Information technology - Telecommunications and Information exchange between systems - Protocol Identification in the network layer, 1990 (E) 1990-10-15.
[3] IEEE, "IEEE Standard for Local and Metropolitan Area Networks: Overview and Architecture", IEEE Standards 802-1990.
[4] ISO/IEC 8473, Information processing systems - Data communications - Protocol for providing the connectionless- mode network service, 1988.
[5] ISO/IEC 9542, Information processing systems - Telecommunications and information exchange between systems - End system to intermediate system routeing protocol for use in conjunction with the protocol for providing the connectionless- mode network service (ISO/IEC 8473), 1988.
[6] Postel, J., Editor., "Internet Protocol - DARPA Internet Program Protocol Specification", RFC 791, USC/Information Sciences Institute, September 1981.
[7] Reynolds, J. and J. Postel, "Assigned Numbers", RFC 1340, USC/Information Sciences Institute, July 1992.
[8] Bradley, T., Brown, C., and A. Malis, "Multiprotocol Interconnect over Frame Relay", RFC 1294, Wellfleet Communications and BBN Communications, January 1992.
[9] "Defense Data Network X.25 Host Interface Specification", contained in "DDN Protocol Handbook", Volume 1, DDN Network Information Center 50004, December 1985.
[10] Everhart, C., Mamakos, L., Ullmann, R, and P. Mockapetris, Editors, "New DNS RR Definitions", RFC 1183, Transarc, University of Maryland, Prime Computer, USC/Information Sciences Institute, October 1990.
[11] ISO/IEC 8208, Information processing systems - Data
Malis, Robinson, & Ullmann [Page 13]
RFC 1356 Multiprotocol Interconnect on X.25 August 1992
communications - X.25 Packet Level Protocol for Data Terminal Equipment, 1987.
8. Authors' Addresses
Andrew G. Malis BBN Communications 150 CambridgePark Drive Cambridge, MA 02140 USA
Phone: +1 617 873 3419 Email: malis@bbn.com
David Robinson Computervision Systems Integration 201 Burlington Road Bedford, MA 01730 USA
