Explore the World of Soft…e: Engineering & Science/Explore_the_World_of_Software_Engineering_and_Science_HRS_Software_1998.iso/programs/statistc/spcex21s.exe/SCREENS.HYP

Text File | 1993-10-30 | 81KB | 2,959 lines

@
opening message
SPC EXpert - Statistical Process Control Software

Developed by:     Quality Software Designs, Inc.
                  933 East Stroop Road
                  Kettering, Ohio 45429
                  messages: [phone]
                  email:    [e-mail]
                         or ...!uunet!meaddata!marks

Quality Software Designs, Inc. can provide customized
versions of SPC EXpert.  Call or write for more information.
@
Next Version
              TELL ME WHAT YOU THINK!!!

It's been a while since SPC EXpert was released.
I would like to see any comments or ideas you may have.

To remove this message or learn more about the next
version of SPC EXpert, write to:

          Quality Software Designs, Inc.
          933 East Stroop Road
          Kettering, Ohio 45429
          email:   [e-mail]
                or ...!uunet!meaddata!marks
@
SPC Redistribution
             SPC EXpert Secondary Distribution
@
get_fname help1
        FILE NAME SELECTION MENU

1. Type in the filename you want to select

   e.g. "run.dmo" or "scat.dmo"

or

2. Type in the PATTERN for a group of files
   for selection by menu.

   e.g.  "*.*" or "a:*.dmo" or "car.*"

or

3. Hit <ENTER> for a menu of all files
@
get_fname help
        FILE NAME SELECTION MENU

1. Select a file from the menu.

2. If you do not wish to make a selection,
   press ESC or click the right mouse button.
@
banner_2
              QUESTIONS OR COMMENTS

If you have questions or comments, please
feel free to write:

        Quality Software Designs, Inc.
        933 East Stroop Road
        Kettering, Ohio 45429
        [phone]  6:00pm-9:00pm Eastern
        email:    [e-mail]
               or ...!uunet!meaddata!marks

@
investigate_1
                     INVESTIGATE

Investigate any out-of-control points in your process.

                       DISCOVER

1. Any out of control pattern means that something is not normal.

2. Something different is going on. Something is affecting the
   process.

3. It is important to figure out what it is   --   good or bad.

                           ACT

1. If its bad, you have to track the cause and get rid of it.

2. If its good, you want to know too.  Then you can make sure
   that you keep doing things that way.
@
TOP_MENU_RESPONSES
A. Select Data File
B. Select Graphic Type
C. View Graphic
D. Control Chart Analysis
E. View Chart Patterns
F. Expert Consultation
G. On-Line Documentation
H. Print/Export
I. Options
J. Editor & File Manager
K. Shell to DOS
quit
@
TOP_MENU_HELP
                         SPC EXpert
                            MAIN MENU ()

#m>HELP<;hypertext help;info.hyp#m - Click on the >HELP< or Press Enter to learn how
       to operate the hypertext help system.

    #m(X.Y.Z);MENU_NOTATION;screens.hyp#m SPC EXpert menu navigation notation.

A. Select Data File
      - Select the name of the ASCII file which contains the
        process data.


B. Select Graphic Type
      - Select the type of control chart.
        Automatic selection is available.


C. View Graphic
      - Graphic display of the current chart/diagram.


D. Control Chart Analysis
      - Automatic analysis of Control Chart for unusual patterns which
        suggest the presence of assignable causes of variation in your
        process.  Stamdard "Western Electric" rules apply.


E. View Control Chart Patterns
      - Graphic Display of each unusual pattern found in D. highlighted
        on the control chart


F. Expert Consultation
      - Expert System consultation which provides generic advice on the
        meaning of each pattern unusual pattern found in D.


G. #mOn-Line Documentation;MORE_INFO_MENU;info.hyp#m
      - More detailed explanation of the SPC EXpert software and its
        licensing and redistribution policies.


H. #mPrint/Export Menu;PRINT_MENU#m
      - Allows you to print a paper copy of the current chart/diagram.
        Also allows you to select the type of printer, printing mode, and
        the printer connection.  This menua also allows the user to export
        SPCEX's output to Computer Graphics Metafiles (CGM) or Encapsulated
        Post Script Files.


I. #mOptions Menu;OPTIONS_MENU#m
      - Allows the ADVANCED USER to select the statistical methods used
        to create the charts/diagrams as well as to alter the appearance
        of the graphics.


J. #mEditor & File Manager;EDIT_MENU#m
      - Integrated text editor and file management system.
        The user has the option to:

             1. Edit the current data file
             2. Edit or create any file
             3. View a file
             4. Copy a file
             5. Rename a file
             6. Delete a File


K. Shell To DOS
      - Allows the user to access DOS while still having SPCEX in memory.


quit
      - Exit the SPCEX application.
@
TOP_CHART_TEXT
Choose an SPC tool type.
@
TOP_CHART_MENU
A. Control Charts
B. Diagrams and Graphs
Return to SPC MAIN MENU
@
TOP_CHART_HELP
               SPC TOOL TYPES

A. #mControl Charts;charts0;info.hyp#m - The following control
chart types are available in SPC EXpert :

                    1. #mRun chart;charts12;info.hyp#m
                    2. #mXbar-R control chart;charts13;info.hyp#m
                    3. #mX Moving Range control chart;charts14;info.hyp#m
                    4. #mXbar-S control chart;charts16;info.hyp#m
                    5. #mpn control chart;charts18;info.hyp#m
                    6. #mp control chart;charts18;info.hyp#m
                    7. #mc control chart;charts21;info.hyp#m
                    8. #mu control chart;charts21;info.hyp#m


B. #mDiagrams & Graphs;graph0;info.hyp#m - The following diagrams and graphs are
               available in SPC EXpert :

                       1. #mBar Graph;graph1;info.hyp#m
                       2. #mPareto Diagram;graph3;info.hyp#m
                       3. #mScatter Diagram;graph6;info.hyp#m
                       4. #mHistogram;graph9;info.hyp#m
                       5. #mFrequency POLYGON;graph10;info.hyp#m
                       6. #mCDF or Ogive;graph11;info.hyp#m
                       7. #mPie Chart;graph5;info.hyp#m
                       8. Data Tables
                       9. Multiple Graphs
@
CHART_MENU_RESPONSES
A. Automatic chart selection
B. X (Run) Chart
C. Xbar Chart
D. R Chart
E. S Chart
F. Moving Range chart
G. Xbar-R control chart
H. Xbar-S control chart
I. X Moving Range control chart
J. pn control chart
K. p control chart
L. c control chart
M. u control chart
Return to Previous Menu
@
CHART_MENU_TEXT
@
CHART_MENU_HELP
                 CHART TYPE SELECTION MENU

1. Use this menu to select the type of control chart to use.

2. If you need help making this selection, choose option A.
   You will be asked 1 to 3 questions concerning the nature
   of your process data.  From your response(s), the control
   chart type will be automatically selected.

3. To directly select a control chart type, choose
   options B - M.

4. To exit this menu, select the last option.

      Click/select for #mOverview of Control Charts;charts0;info.hyp#m.
@
DIAGRAM_MENU_RESPONSES
A. Bar Graph
B. Pareto Diagram
C. Pie Chart
D. Table
E. Histogram
F. Frequency POLYGON
G. CDF or Ogive
H. Scatter Diagram
I. Multiple Graphs
Return to Previous Menu
@
DIAGRAM_MENU_TEXT
@
DIAGRAM_MENU_HELP
           DIAGRAM TYPE SELECTION MENU

1. Use this menu to select the type of diagram to use.

2. To directly select a diagram type, choose
   options A - I.

3. To exit this menu, select the last option.

      Click/select for #mOverview of Graphs/Diagrams;graph0;info.hyp#m.
@
DATA_TYPE_TEXT
What type of process data are
you measuring?
@
DATA_TYPE_MENU
A. Measurement
B. Attribute
@
DATA_TYPE_HELP
A. Measurement Data - This is indiscrete or continuous valued data.

                      Examples include : length
                                         weight
                                         time

B. Attribute Data   - This is discrete valued data.

                      Examples include : number of errors
                                         number of rejects
                                         number of reworks
@
SAMPLE_SIZE_TEXT
Is your logical group size (Sample Size)
constant or variable?
@
SAMPLE_SIZE_MENU
A. Constant
B. Variable
@
SAMPLE_SIZE_HELP
1. Constant - Examples include :

              (a) # pin holes in a fixed area of sheet metal
              (b) # rejects out of a fixed batch size

2. Variable - Examples include :

              (a) # pin holes in pieces of sheet metal differing in area
              (b) # rejects out of batches differing in size
              (c) # typographic errors in letters (of differing length)
@
VALUES_VARIABILITY_TEXT
Do you want to show process
values, variability, or both?
@
VALUES_VARIABILITY_MENU
A. Values
B. Variability
C. Both
@
VALUES_VARIABILITY_HELP
                     VALUES vs VARIABILITY
                   Measurement Control Charts

Use this menu to indicate what aspect, values and/or variability,
of your measurement data you wish to display.

   A. Values - Show the actual levels (values) of your process
               measurements.  Control charts which show process
               levels or values include individuals (RUN) and
               averages (XBAR).

   B. Variability - Show how your process measurements are
                    dispersed.  Control charts which show
                    process dispersion or variability include
                    range (R), standard deviation (S) and
                    moving range (MR).

   C. Both - Show both the level (values) and the variability
             of your process.  Charts which show both values
             and variability include individuals moving range
             (XMR), average and range (XBAR_R), and average
             and standard deviation (XBAR_S).  These are simply
             combinations of charts from A and B above.
@
SAMPLE_CARDINALITY_TEXT
In what range is your
logical group (sample)
size?
@
SAMPLE_CARDINALITY_MENU
A. 1
B. 2 to 10
C. Larger Than 10
@
SAMPLE_CARDINALITY_HELP
LOGICAL GROUP SIZE
Measurement Control Charts

Use this menu to indicate the relative size of your process samples
when gathering measurement data.

    A. 1              - Appropriate measurement control charts include:
                           VALUES: RUN
                           VARIABILITY: MR

    B. 2 to 10        - Appropriate measurement control charts include:
                           VALUES: XBAR
                           VARIABILITY: R


    C. Larger Than 10 - Appropriate measurement control charts include:
                           VALUES: XBAR
                           VARIABILITY: S
@
DEFECT_TEXT
Is your attribute data measuring
defectives or defects?
@
DEFECT_MENU
A. Defectives
B. Defects
@
DEFECT_HELP
1. Defectives - This is the number of parts/units/etc that
                are rejected or un-usable.  Examples include :

                    (a) # letters returned for rework.
                    (b) # sheets of metal rejected.


2. Defects - This is the number of flaws in a part/unit/etc.
             Example include :

                   (a) # typographic errors in a letter.
                   (b) # pin holes in a sheet of metal.
@
CONSULT_TEXT
Select a pattern for
expert consultation
@
CONSULT_HELP
            EXPERT CONSULTATION MENU

1. Several Patterns which suggest the presence of
   assignable causes of variation within the process
   have been located in your control chart.

2. Select a pattern for which you would like more
   information.

3. Select option 1 to see advice for every pattern
   found in your chart.

4. Select the last option to return to the MAIN MENU.
@
VIEW_TEXT
Select a pattern
to view highlighted
on the chart.
@
VIEW_HELP
               VIEW PATTERNS MENU


1. Several Patterns which suggest the presence of
   assignable causes of variation within the process
   have been located in your control chart.


2. Select a pattern which you would like to view.


3. Select option 1 to view every pattern found in your chart.


4. Select the last option to return to the MAIN MENU.
@
view_in_control_chart
Your chart is in control!  This means that there are
no unusual patterns within the chart which suggest
the presence of assignable causes of variation.

Select the consultation option for further details.
@
PRINT_MENU
A. Print Graphic
B. View Graphic
C. Printer Type
D. Print Orientation/Density
E. I/O Port
F. Advanced Comm Parameters
G. Save Printer Settings
H. Export to Graphics File
I. Export to EPS File
J. Manually Set Video Mode
Return To MAIN MENU
@
PRINT_HELP
            SPC EXpert PRINT MENU (H)

A. Print Graphic (H.A)
     - Produces a hard copy of the current graphic.


B. View Chart/Diagram (H.B)
     - Displays graphics of current graphic.


C. Select Printer Type (H.C)
     - Allows you the specify what kind of printer you have.
       The following printers are supported:

              A. Epson FX/IBM Pro Printer
              B. Epson LQ
              C. IBM Proprinter X24
              D. IBM Quietwriter
              E. Toshiba P321
              F. HP Laserjet
              G. Post Script
              H. Paint Jet
              I. HP 7470 Plotter
              J. HP 7475 Plotter
              K. HP 7550 Plotter
              L. HP 7585 Plotter
              M. HP Desk Jet
              N. HP Desk Jet 500C
              O. HP Desk Jet 550C
              P. HP Laser Jet III
              Q. HP Laser Jet IV
              R. Canon Laser

D. Select Orientation/density (H.D)
      - Allows you to select the orientation and print density
        of your printout. The print orientations and densities
        supported vary with each printer:


                 A. #mEpson FX/IBM Pro Printer;$FX#m
                 B. #mEpson LQ;$LQ#m
                 C. #mIBM Proprinter X24;$PP24#m
                 D. #mIBM Quietwriter;$IBMQ#m
                 E. #mToshiba P321;$TSH#m
                 F. #mHP Laserjet;$LJ#m
                 G. #mPost Script;$PS#m
                 H. #mPaint Jet;$PJET#m
                 I. #mHP 7470 Plotter;$HP7470#m
                 J. #mHP 7475 Plotter;$HP7475#m
                 K. #mHP 7550 Plotter;$HP7550#m
                 L. #mHP 7585 Plotter;$HP7585#m
                 M. #mHP Desk Jet;$DJ#m
                 N. #mHP Desk Jet 500C;$DJC#m
                 O. #mHP Desk Jet 550C;$DJC550#m
                 P. #mHP Laser Jet III;$LJ3R#m
                 Q. #mHP Laser Jet IV;$LJ4#m
                 R. #mCanon Laser;$CANON#m

E. Select I/O Port (H.E)
     -  Allows you to select the external port to which your printer
        is connected.  The following ports are supported:

                 A. LPT1 (Parallel Port #1)
                 B. LPT2 (Parallel Port #2)
                 C. COM1 (Serial Port #1)
                 D. COM2 (Serial Port #2)


F. Advanced Comm Parameters (H.F)
       - This allows you to adjust some specific communications
         parameters between your computer and your printer for
         the SERIAL Ports (COM1 & COM2).  These include:

                          A. Baud [default: 2400]
                          B. Parity [default: None]
                          C. # Data Bits [default: 8]
                          D. # Stop Bits [default: 1]

               *** The default settings are usually appropriate.
                   Only attempt to adjust these as a last resort.


G. Save Printer Settings (H.G)
       - This option allows you to save the settings that you selected
         in options C,D,E, and J.  The next time you start SPCEX, those
         saved settings will be selected by default.



H. Export to Graphics File (H.H)
       - This allows you to save the current graphic, as it appears
         when viewed with option B, to one of several Computer Graphics
         file formats.  These graphics format can be imported into a wide
         variety of commercial graphics software packages such as Harvard
         Graphics, WordPerfect, MicroSoft Word, and MicroSoft PowerPoint.

             A. PCX 16 Color 640x480
             B. PCX Mono 640x480
             C. Windows 3.X BMP 16 Color 640x480
             D. Windows 3.X BMP Mono 640x480
             E. Gem IMG Low  Mono 720x540
             F. Gem IMG Med  Mono 1440x1080
             G. Gem IMG High Mono 2880x2160
             H. TIFF (compressed) Low 720x540
             I. TIFF (compressed) Med 1440x1080
             J. TIFF (compressed) High 2880x2160
             K. TIFF (uncompressed) Low 720x540
             L. TIFF (uncompressed) Med 1440x1080
             M. TIFF (uncompressed) High 2880x2160
             N. ANSI CGM 256 Color 32767x24574
             O. ANSI CGM Mono 32767x24574
             P. AutoCad DXF 16 Color 10000x7200
             Q. Video Show (NAPLPS) 256 Color 2048x1824
             R. WordPerfect Graphics 16 Color 7800x6000
             S. WordPerfect Graphics Mono 7800x6000


I. Export to EPS File (H.I)
       - This allows you to save the current graphic, as it appears when
         viewed with option B, to a Encapsulated Post Script (EPS) file.
         An EPS file can be taken to any Post Script printer and printed
         at a later date.


J. Manually Set Video Mode (H.J)
       - This allows you to manually select the type of monitor that your
         computer has.  SPCEX WILL DETECT THE TYPE OF MONITOR YOU HAVE ON
         MOST SYSTEMS.  However, some computer systems do not work with
         SPCEX's AUTODETECT feature and may require you to explicitly
         specify what type of monitor you have.


Return to MAIN MENU
       - Return to Main Menu.
@
TYPE_PRINTER_TEXT
@
TYPE_PRINTER_MENU
A. Epson FX/IBM Pro Printer
B. Epson LQ
C. IBM Proprinter X24
D. IBM Quietwriter
E. Toshiba P321
F. HP Laserjet
G. Post Script
H. Paint Jet
I. HP 7470 Plotter
J. HP 7475 Plotter
K. HP 7550 Plotter
L. HP 7585 Plotter
M. HP Desk Jet
N. HP Desk Jet 500C
O. HP Desk Jet 550C
P. HP Laser Jet III
Q. HP Laser Jet IV
R. Canon Laser
return
@
TYPE_PRINTER_HELP
          PRINTER TYPES SUPPORTED BY SPC EXpert (H.C)

This option allows you the specify what kind of printer
you have.  The following printers are supported:


         A. Epson FX/IBM Pro Printer (H.C.A)
         B. Epson LQ                 (H.C.B)
         C. IBM Proprinter X24       (H.C.C)
         D. IBM Quietwriter          (H.C.D)
         E. Toshiba P321             (H.C.E)
         F. HP Laserjet              (H.C.F)
         G. Post Script              (H.C.G)
         H. Paint Jet                (H.C.H)
         I. HP 7470 Plotter          (H.C.I)
         J. HP 7475 Plotter          (H.C.J)
         K. HP 7550 Plotter          (H.C.K)
         L. HP 7585 Plotter          (H.C.L)
         M. HP Desk Jet              (H.C.M)
         N. HP Desk Jet 500C         (H.C.N)
         O. HP Desk Jet 550C         (H.C.O)
         P. HP Laser Jet III         (H.C.P)
         Q. HP Laser Jet IV          (H.C.Q)
         R. Canon Laser              (H.C.R)

 If your printer is not on this list, you still may be able to
 make a printout.  Consult your printer's documentation of just
 simply experiment.
@
DPI_HELP
       Select Orientation/density (H.D) HELP

Allows you to select the orientation and print density
of your printout. The print orientations and densities
supported vary with each printer:


       A. #mEpson FX/IBM Pro Printer;$FX#m
       B. #mEpson LQ;$LQ#m
       C. #mIBM Proprinter X24;$PP24#m
       D. #mIBM Quietwriter;$IBMQ#m
       E. #mToshiba P321;$TSH#m
       F. #mHP Laserjet;$LJ#m
       G. #mPost Script;$PS#m
       H. #mPaint Jet;$PJET#m
       I. #mHP 7470 Plotter;$HP7470#m
       J. #mHP 7475 Plotter;$HP7475#m
       K. #mHP 7550 Plotter;$HP7550#m
       L. #mHP 7585 Plotter;$HP7585#m
       M. #mHP Desk Jet;$DJ#m

@
PORT_TEXT
Select The I/O Port
to which your printer
is connected.
@
PORT_MENU
A. LPT1
B. LPT2
C. COM1
D. COM2
@
PORT_HELP
                 DEVICE PORT (H.E) HELP

This menu allows you to select the external port to which
your printer is connected.  The following ports are supported:


                A. LPT1 (Parallel Port #1)*
                B. LPT2 (Parallel Port #2)
                C. COM1 (Serial Port #1)
                D. COM2 (Serial Port #2)

* LPT1 is the standard printer port.
@
COMM_TEXT

@
COMM_MENU
A. Baud
B. Parity
C. Data Bits
D. Stop Bits
E. XON/XOFF
F. Reset to Defaults
Return
@
COMM_HELP
      Advanced Comm Parameters Help (H.F)

This allows you to adjust some specific communications
parameters between your computer and your printer for
the SERIAL Ports (COM1 & COM2).  These include:

A. Baud [default: 2400]      (H.F.A)
B. Parity [default: None]    (H.F.B)
C. # Data Bits [default: 8]  (H.F.C)
D. # Stop Bits [default: 1]  (H.F.D)
E. XON/XOFF [default: XOFF]  (H.F.E)

   *** The default settings are usually appropriate.
       Only attempt to adjust these as a last resort.

@
BAUD_TEXT

@
BAUD_MENU
A. 110 Baud
B. 150 Baud
C. 300 Baud
D. 600 Baud
E. 1200 Baud
F. 2400 Baud
G. 4800 Baud
H. 9600 Baud
Return
@
BAUD_HELP
Serial Port Baud Rate (H.F.A) HELP

This allows you to adjust the rate
(Baud rate) at which the computer
attempts to communicate through
the serial ports (COM1 or COM2).
The default setting is  2400 Baud.

The choices for Baud rate are:

    A. 110 Baud  (H.F.A.A)
    B. 150 Baud  (H.F.A.B)
    C. 300 Baud  (H.F.A.C)
    D. 600 Baud  (H.F.A.D)
    E. 1200 Baud (H.F.A.E)
    F. 2400 Baud (H.F.A.F)
    G. 4800 Baud (H.F.A.G)
    H. 9600 Baud (H.F.A.H)
@
PARITY_TEXT

@
PARITY_MENU
A. None
B. Odd Parity
C. Even Parity
Return
@
PARITY_HELP
Serial Port Parity (H.F.B) HELP

This allows you to select one of
the methods the computer and printer
use to chack that no errors in
communication over the serial
ports (COM1 or COM2) have occured.

The choices for parity are:

    A. None         (H.F.B.A)
    B. Odd Parity   (H.F.B.B)
    C. Even Parity  (H.F.B.C)

The default setting is  NONE.

@
DATA_TEXT

@
DATA_MENU
A. 7 Data Bits
B. 8 Data Bits
Return
@
DATA_HELP
 Serial Port DATA BITS (H.F.C) HELP

This allows you to select the serial
port (COM1 or COM2) communications
setting for Number of DATA BITS.

The choices for Data Bits are:

    A. 7 Data Bits (H.F.C.A)
    B. 8 Data Bits (H.F.C.B)

The default setting is  8 Data Bits.

@
STOP_TEXT

@
STOP_MENU
A. 1 Stop Bit
B. 2 Stop Bits
Return
@
STOP_HELP
 Serial Port STOP BITS (H.F.D) HELP

This allows you to select the serial
port (COM1 or COM2) communications
setting for Number of STOP BITS.

The choices for Stop Bits are:

    A. 1 Stop Bit  (H.F.D.A)
    B. 2 Stop Bits (H.F.D.B)


The default setting is  1 Stop Bit.

@
XON_TEXT

@
XON_MENU
A. XOFF
B. XON
Return
@
XON_HELP
 Serial Port XON/XOFF (H.F.E) HELP

This allows you to select the serial
port (COM1 or COM2) communications
setting for XON/XOFF.

The choices are:

    A. XOFF (H.F.E.A)
    B. XON  (H.F.E.B)

The default setting is  XOFF.

@
$FX
A. Half Low
B. Half Med
C. Half High
D. Land Low
E. Land Med
F. Land High
G. Full Low
H. Full Med
I. Full High
Return
@
$LQ
A. Half Low
B. Half Med
C. Half High
D. Land Low
E. Land Med
F. Land High
G. Full Low
H. Full Med
I. Full High
Return
@
$PP24
A. Half Low
B. Half Med
C. Half High
D. Land Low
E. Land Med
F. Land High
G. Full Low
H. Full Med
I. Full High
Return
@
$IBMQ
A. Half Low
B. Half Med
C. Half High
D. Land Low
E. Land Med
F. Land High
G. Full Low
H. Full Med
I. Full High
Return
@
$TSH
A. Half
B. Land
C. Full
Return
@
$LJ
A. Half Low
B. Half Med
C. Half High
D. Land Low
E. Land Med
F. Land High
G. Full Low
H. Full Med
I. Full High
Return
@
$LJ3R
A. Half Low
B. Half Med
C. Half High
D. Land Low
E. Land Med
F. Land High
G. Full Low
H. Full Med
I. Full High
Return
@
$CANON
A. Half Low
B. Half Med
C. Half High
D. Land Low
E. Land Med
F. Land High
G. Full Low
H. Full Med
I. Full High
Return
@
$LJ4
A. Half Low
B. Half Med
C. Half High
D. Land Low
E. Land Med
F. Land High
G. Full Low
H. Full Med
I. Full High
Return
@
$DJ
A. Half Low
B. Half Med
C. Half High
D. Land Low
E. Land Med
F. Land High
G. Full Low
H. Full Med
I. Full High
Return
@
$DJC
A. Half Low
B. Half Med
C. Half High
D. Land Low
E. Land Med
F. Land High
G. Full Low
H. Full Med
I. Full High
Return
@
$DJC550
A. Half Low
B. Half Med
C. Half High
D. Land Low
E. Land Med
F. Land High
G. Full Low
H. Full Med
I. Full High
Return
@
$PJET
A. Half Low     Mono
B. Land Low     Mono
C. Half High    Mono
D. Land High    Mono
E. Half Low   4 Color
F. Land Low   4 Color
G. Half High  4 Color
H. Land High  4 Color
I. Half Low   8 Color
J. Land Low   8 Color
K. Half High  8 Color
L. Land High  8 Color
M. Half Low  16 Color
N. Land Low  16 Color
Return
@
$PS
A. Half    Mono
B. Land    Mono
C. Full    Mono
D. Half 16 Grays
E. Land 16 Grays
F. Full 16 Grays
G. Half 16 Color
H. Land 16 Color
I. Full 16 Color
Return
@
$HP7470
A. Draft 16 Color 10000x7200
B. LQ    16 Color 10000x7200
Return
@
$HP7475
A. Draft 16 Color 10000x7200
B. LQ    16 Color 10000x7200
C. Draft 16 Color 15200x10000
D. LQ    16 Color 15200x10000
Return
@
$HP7550
A. Draft 16 Color 10000x7200
B. LQ    16 Color 10000x7200
Return
@
$HP7585
A. Draft 16 Color 5580x9000
B. LQ    16 Color 5580x9000
C. Draft 16 Color 14200x9000
D. LQ    16 Color 14200x9000
Return
@
DTP_TEXT
@
DTP_HELP
Use this menu to choose the Graphics File
format that you would like to save the
current chart to.  The following formats
available:

     - Zsoft PCX
     - Windows 3 BMP
     - GEM IMG
     - TIFF (compressed & uncompressed)
     - ANSI CGM
     - AutoDesk DXF
     - General Parametrics VideoShow
       (ANSI NAPLPS with some extensions)
     - WordPerfect WPG

@
DTP_MENU
A. PCX 16 Color 640x480
B. PCX Mono 640x480
C. Windows 3.X BMP 16 Color 640x480
D. Windows 3.X BMP Mono 640x480
E. Gem IMG Low  Mono 720x540
F. Gem IMG Med  Mono 1440x1080
G. Gem IMG High Mono 2880x2160
H. TIFF (compressed) Low 720x540
I. TIFF (compressed) Med 1440x1080
J. TIFF (compressed) High 2880x2160
K. TIFF (uncompressed) Low 720x540
L. TIFF (uncompressed) Med 1440x1080
M. TIFF (uncompressed) High 2880x2160
N. ANSI CGM 256 Color 32767x24574
O. ANSI CGM Mono 32767x24574
P. AutoCad DXF 16 Color 10000x7200
Q. Video Show (NAPLPS) 256 Color 2048x1824
R. WordPerfect Graphics 16 Color 7800x6000
S. WordPerfect Graphics Mono 7800x6000
return
@
$DTP
$PCX 0 13 1
$PCX 1 13 0
$BMP 0 14 1
$BMP 1 14 0
$IMG 0 15 0
$IMG 1 15 0
$IMG 2 15 0
$TIF 0 16 0
$TIF 1 16 0
$TIF 2 16 0
$UTIF 0 17 0
$UTIF 1 17 0
$UTIF 2 17 0
$CGM 0 18 1
$CGM 1 18 0
$DXF 0 19 1
$VSHO 0 20 1
$WPG 0 21 1
$WPG 1 21 0
@
C$FX
0
0
0
0
0
0
0
0
0
@
C$LQ
0
0
0
0
0
0
0
0
0
@
C$PP24
0
0
0
0
0
0
0
0
0
@
C$IBMQ
0
0
0
0
0
0
0
0
0
@
C$TSH
0
0
0
@
C$LJ
0
0
0
0
0
0
0
0
0
@
C$LJ3R
0
0
0
0
0
0
0
0
0
@
C$CANON
0
0
0
0
0
0
0
0
0
@
C$LJ4
0
0
0
0
0
0
0
0
0
@
C$DJ
0
0
0
0
0
0
0
0
0
@
C$DJC
1
1
1
1
1
1
1
1
1
@
C$DJC550
1
1
1
1
1
1
1
1
1
@
C$PJET
0
0
0
0
1
1
1
1
1
1
1
1
1
1
@
C$PS
0
0
0
1
1
1
1
1
1
@
C$HP7470
1
1
@
C$HP7475
1
1
1
1
@
C$HP7550
1
1
@
C$HP7585
1
1
1
1
@
OPTIONS_MENU
A. Control Charts
B. Distribution Graphs
C. PIE/BAR/PARETO/TABLE
D. Scatter Diagrams
E. Process Specifications
F. Data File Formats
G. Fonts & Font Sizes
H. Titles/Stats/etc
I. Saving/Recalling Options
J. Display Current Options
Return to Main Menu
@
OPTIONS_TEXT
@
OPTIONS_HELP
             Options Menu Help Screen (I)

#mA. Control Charts;CC_OPTIONS_MENU#m
      This allows you to set parameters which affect the statistical
      calculations and appearance of all control charts.

#mB. Distribution Graphs;DIST_OPTIONS_MENU#m
      This allows you to set parameters which affect the statistical
      calculations and appearance of HISTOGRAMS, frequency POLYGONS,
      and CDFs.

#mC. PIE/BAR/PARETO/TABLE;PIE_OPTIONS_MENU#m
      This allows you to set parameters which affect the statistical
      calculations and appearance of PIE charts, BAR graphs, PARETO
      diagrams, and data TABLES.

#mD. Scatter Diagrams;SCATTER_OPTIONS_MENU#m
      This allows you to set parameters which affect the statistical
      calculations and appearance of SCATTER DIAGRAMS.

#mE. Process Specifications;SPECS_OPTIONS_MENU#m

      This menu allows you to set upper and lower SPECIFICATION
      limits.  These specification limits are used for process
      capability statistics in control charts, distribution graphs,
      and scatter diagrams.

#mF. Data File Formats;RAW_DATA_OPTIONS_MENU#m
      This option has been included in SPC EXpert to accomadate
      future enhancements which include the ability to import
      data from DBase-type database files.

#mG. Fonts & Font Sizes;FONTS_OPTIONS_MENU#m
      This allows you to select the font sizes and types to be used
      for the titles and axis labels on all graphics.

#mH. Titles/Stats/etc;DISPLAY_OPTIONS_MENU#m
      This allows you to set parameters which affect all types of
      charts and diagrams.  These include:

                     A. Titles ON/OFF
                     B. Enhanced Labeling ON/OFF
                     C. Summary Stats ON/OFF
                     D. Sound ON/OFF

#mI. Saving/Recalling Options;SAVE_CFG_OPTIONS_MENU#m
      Allows you to save and recall your options settings.

J. Display Current Options
      Use this to display the current options settings.

Return to Main Menu

@
CC_OPTIONS_MENU
A. Range to Display
B. Range to Calc Control Limits
C. Range for Stats/Regression
D. Method for Center Line
E. Method for Control Limits
F. Dist Graph to Display
G. X-Axis Labeling Convention
H. Y-Axis Labeling Convention
I. Control Limits/Zones
J. Process Specs ON/OFF
K. Linear Regression ON/OFF
L. Eliminate Outliers ON/OFF
M. MIN Lengths for Analysis
Return to OPTIONS MENU
@
CC_OPTIONS_TEXT

@
CC_OPTIONS_HELP
           Control Chart Options Menu (I.A) Help Screen

A. Range to Display (I.A.A)
    - You may select the range of data to be displayed on the output.
      A maximum of 16000 data points may be displayed at one time for
      any control chart.  The practical limit for most video monitors
      is about 200-300 data points.  The graphic output is scaled to
      accommodate the data ranges.

B. Range to Calc Control Limits (I.A.B)
    - You may set what range of data is used in the calculation of
      the control limits (upper & lower limits, center line, Cp, Cpl,
      Cpu, Cpk, and percent in-spec).  The display of these statistics
      may be turned on/off using selection I.H.C.  The control chart
      process specifications (I.A.J) must be turned ON to display the
      in-spec and capability statistics.

C. Range for Stats/Regression (I.A.C)
    - You may set the range of data used to calculate standard
      statistics and linear regression.  The standard statistics
      display may be turned on/off using selection I.H.C.  This
      range is also the range of data used for the automated control
      chart ANALYSIS - selection D.

D. Method for Center Line (I.A.D)
    - You may select the method used to determine the center line
      using data in the Limits Range (I.A.B).  The center line can
      be determined using the mean, median or a user specified value.

E. Method for Control Limits (I.A.E)
    - You may select the method used to calculate the control limits
      using data in the Limits Range (I.A.B).

F. Dist Graph to Display (I.A.F)
    - You may display a data distribution function on a control chart.

G. X-Axis Labeling Convention (I.A.G)
    - You may select the type of label for the X (horizontal) Axis.

H. Y-Axis Labeling Convention (I.A.H)
    - You may select the type of label for the Y (vertical) Axis.

I. Control Limits/Zones (I.A.I)
    - You may specify what control limit markings are plotted on a
      control chart besides the center line.

J. Process Specs ON/OFF (I.A.J)
    - You may use this selection to toggle ON/OFF the current process
      specifications.  Process specifications may be set using
      selection I.E.  When this is ON, the process specifications
      are graphically displayed on the control chart.  Capability
      statistics are displayed when Process Specs (I.A.J) and
      Summary Stats (I.H.C) are BOTH "ON".

K. Linear Regression ON/OFF (I.A.K)
    - This allows you to plot (or not) the linear regression line
      calculated from the data points in the Stats Range (I.A.C)
      on control charts.  The default setting is "OFF".

L. Eliminate Outliers ON/OFF (I.A.L)
    - You may designate any data points in a data file for control
      charts as "outliers"   When eliminate outliers is ON, points
      defined as outliers will be highlighted and will not be used
      in the calculations.  The default setting is "OFF".

M. MIN Lengths for Analysis (I.A.M)
    - You may use this to set the minimum length required for each
      control chart out-of-control condition to be reported after
      the automatic control chart analysis (selection D).

Return to OPTIONS MENU
    - Use this option (or ESC or RIGHT-MOUSE-BUTTON or <F2>) to
      return to the SPC EXpert options menu (selection I).
@
DISPLAY_RANGE_MENU
A. All
B. Last N
C. Range a to b
Return
@
DISPLAY_RANGE_TEXT

@
DISPLAY_RANGE_HELP
              Display Range Menu (I.A.A) Help
                     [default: ALL]

You may select the range of data to be displayed on the output.
A maximum of 16000 data points may be displayed at one time for
all control charts.  The graphic output is scaled to accommodate
the data ranges.  To set the range, select one of the following:

A. All (I.A.A.A)
    - Display the entire control chart (up to 16000 points).
      The practical limit due to screen resolution is 200-300.

B. Last N (I.A.A.B)
    - Display the most recent N (user provided) data points.
      You will be prompted to enter a value for N.

C. Range a to b (I.A.A.C)
    - Display a range of data points where you provide the
      start and end data indices to be displayed.  The first
      data point has index 1.  You will be prompted to enter
      the values for indices a and b.

Return
    - Do not change the DISPLAY range.
@
CL_RANGE_MENU
A. All
B. First M
C. Range a to b
D. Same as DISPLAY
Return
@
CL_RANGE_TEXT

@
CL_RANGE_HELP
             Control Limits Range Help (I.A.B)
                     [default: ALL]

You may set what range of data is used in the calculation of
the control limits (upper & lower limits, center line, Cp, Cpl,
Cpu, Cpk, and percent in-spec).  The display of these statistics
may be turned on/off using selection I.H.C.  The control chart
process specifications (I.A.J) must be turned ON to display the
in-spec and capability statistics.  You nay choose from:

A. All (I.A.B.A)
    - Use all of the data points to calculate the control limits.

B. First M (I.A.B.B)
    - Use the first M (user provided) data points for control
      limits.  You will be prompted to enter a value for M.

C. Range a to b (I.A.B.C)
    - Use a user provided range to calculate the control limits.
      the first data point has index 1.  You will be prompted
      to enter the values for indices a and b.

D. Same as DISPLAY (I.A.B.D)
    - Calculate the control limits using the data in the
      DISPLAY (I.A) range.

Return
    - Do not change the control limits range.
@
STATS_RANGE_MENU
A. All
B. Range a to b
C. Same as LIMITS
D. Same as DISPLAY
Return
@
STATS_RANGE_TEXT

@
STATS_RANGE_HELP
                Stats Range Menu Help (I.A.C)
                     [default: ALL]

You may set the range of data used to calculate standard
statistics and linear regression.  The standard statistics
display may be turned on/off using selection I.H.C.  This
range is also the range of data used for the automated control
chart ANALYSIS - selection D.  Select from:


A. All (I.A.C.A)
    - Calculate statistics and perform chart analysis on ALL
      data points in the control chart.

B. Range a to b (I.A.C.B)
    - Calculate statistics and perform chart analysis using
      the data points in a user provide range and data point
      indices.  The first data point in the control chart has
      index 1.  You will be prompted to enter values for a and b.

C. Same as LIMITS (I.A.C.C)
    - Calculate statistics and perform chart analysis using
      data points in the LIMITS (I.A.B) range.

D. Same as DISPLAY (I.A.C.D)
    - Calculate statistics and perform chart analysis using
      data points in the DISPLAY (I.A.A) range.

Return
    - Do not change the STATS range.
@
CENTER_LINE_MENU
A. Mean (Average)
B. Median
C. User Defined
Return
@
CENTER_LINE_TEXT

@
CENTER_LINE_HELP
                 Center Line Type Help (I.A.D)
                       [default: MEAN]

You may select the method used to determine the center line
using data in the Limits Range (I.A.B).  NOTE: the center
line is used as the process center when applying the "Western
Electric" rules during control chart analysis (selection D).
The center line can be determined using the folowing:


A. Mean (Average) (I.A.D.A)
    - Use the average of the data points in the LIMITS range
      to calculate the center line.  This is the most common
      method used to determine the process center line.

B. Median (I.A.D.B)
    - Use the median of the data points in the LIMITS range
      to calculate the center line.  This method is often
      to minimize the effect of outliers and unusual data
      values on the process center calculation.  The median
      is the value for which an equal number of data values
      fall above and below.

C. User Defined (I.A.D.C)
    - Use a value you provide as the process center.  THIS
      METHOD IS NOT RECOMMENDED!  Use at your own risk!

Return
    - Return to the Control Chart Options (I.A) menu.

@
CONTROL_LIMIT_MENU
A. TABLE look-up
B. 3*Sigma(N)
C. 3*Sigma(N-1)
D. M*Sigma(N)
E. M*Sigma(N-1)
F. 3*User-Defined-Sigma
Return
@
CONTROL_LIMIT_TEXT

@
CONTROL_LIMIT_HELP
                    Control Limit Type Help (I.A.E)
                       (default: TABLE Lookup)

You may select the method used to calculate the control limits
using data in the Limits Range (I.A.B).  NOTE: the control
limits are used as +- 3 standard deviations when applying the
"Western Electric" rules during control chart analysis
(selection D).  The center line can be determined as folows:


A. TABLE look-up (I.A.E.A)
    - This approximates the control limits from statistical
      tables or formulas.  This is the traditional method
      used to calculate control limits.  In case where your
      process may be out of control in the LIMITS range,
      this method is recommended.

B. 3*Sigma(N) (I.A.E.B)
    - This approximates the control limits using +- 3 standard
      deviations with N degrees of freedom.  This method should
      only be used to calculate control limits, IF YOU ARE
      CERTAIN THAT YOUR PROCESS IS STABLE AND IN CONTROL in the
      LIMITS range.


C. 3*Sigma(N-1) (I.A.E.C)
    - This approximates the control limits using +- 3 standard
      deviations with N-1 degrees of freedom.  This method should
      only be used to calculate control limits, IF YOU ARE
      CERTAIN THAT YOUR PROCESS IS STABLE AND IN CONTROL in the
      LIMITS range.


D. M*Sigma(N) (I.A.E.D)
    - This approximates the control limits using +- M standard
      deviations with N degrees of freedom - where you are prompted
      for the value of M.  This method should only be used to calculate
      control limits, IF YOU ARE CERTAIN THAT YOUR PROCESS IS
      STABLE AND IN CONTROL in the LIMITS range.  This is commonly
      used with M<3 in an attempt to reduce the variability of
      a stable, in-control process.


E. M*Sigma(N-1) (I.A.E.E)
    - This approximates the control limits using +- M standard
      deviations with N-1 degrees of freedom - where you are prompted
      for the value of M.  This method should only be used to calculate
      control limits, IF YOU ARE CERTAIN THAT YOUR PROCESS IS
      STABLE AND IN CONTROL in the LIMITS range.  This is commonly
      used with M<3 in an attempt to reduce the variability of
      a stable, in-control process.


F. 3*User-Defined-Sigma (I.A.E.F)
    - This approximates the control limits using +- 3 times a
      standard deviation you provide.  This method might be used
      in an attempt to reduce the variability of a stable, in-
      control process.  Several types of short run control charts
      (WAIT FOR NEXT RELEASE OF SPC EX) eliminate any need for
      this though.

Return
    - Return to the Control Chart Options (I.A) menu.

@
CC_DIST_MENU
A. none
B. Histogram
C. Frequency Polygon
D. Ogive (CDF)
E. Individuals Histogram
F. Individuals Polygon
G. Individuals Ogive (CDF)
Return
@
CC_DIST_TEXT

@
CC_DIST_HELP
   Control Chart Distribution Graph Display Type Help (I.A.F)
                      [default: none]

You may display a data distribution function on a control chart.
The distribution graphic may be either a HISTOGRAM, frequency
POLYGON, or CDF.  The distribution graphic is calculated using
the data values in the STATS (I.A.C) range.  For XBAR control
charts, there must be a distinction between the collection of
averages and the collection of individual data points - this
is made by selecting and "INDIVIDUALS" distribution graphic.
The appearance of the distribution graphic may be changed using
the Distribution Graphics Option (I.B) menus.  Select from:


A. none (I.A.F.A)
    - Do not display any distribution graphic.

B. Histogram (I.A.F.B)
    - Display a HISTOGRAM of the chart values in the STATS range.
      For an XBAR chart, this will reflect the distribution of
      the sample averages.

C. Frequency Polygon (I.A.F.C)
    - Display a POLYGON of the chart values in the STATS range.
      For an XBAR chart, this will reflect the distribution of
      the sample averages.

D. Ogive (CDF) (I.A.F.D)
    - Display a CDF of the chart values in the STATS range.
      For an XBAR chart, this will reflect the distribution of
      the sample averages.

E. Individuals Histogram (I.A.F.E)
    - Display a HISTOGRAM of the individual data values in the
      STATS range.  For an XBAR chart, this will reflect the
      distribution of the individual data samples.

F. Individuals Polygon (I.A.F.F)
    - Display a POLYGON of the individual data values in the
      STATS range.  For an XBAR chart, this will reflect the
      distribution of the individual data samples.

G. Individuals Ogive (CDF) (I.A.F.G)
    - Display a CDF of the individual data values in the
      STATS range.  For an XBAR chart, this will reflect the
      distribution of the individual data samples.

Return
    - Return to the Control Chart Options (I.A) menu.

@
CC_X_AXIS_MENU
A. none
B. User Defined Strings
C. Values of Data Points
D. Data point indices (1,2,...N)
Return
@
CC_X_AXIS_TEXT

@
CC_X_AXIS_HELP
        Control Chart X Axis Labeling Type Help (I.A.G)
                     [default: none]

You may select the type of label for the X (horizontal) Axis.
Select from the following:

A. none (I.A.G.A)
    - Do not print labels along the X-axis.


B. User Defined Strings (I.A.G.B)
    - Displays the strings (possibly empty if none provided)
      that you provide in the comment field of the data file.
      If you provide no comments in the data file, then this
      will appear exactly as X-axis lable option none (I.A.G.A).


C. Values of Data Points (I.A.G.C)
    - Displays the actual value of the data point in the chart.
      This value is the actual number plotted above/below the
      X-Axis -- for XBAR charts this value will be the sample
      average, for P charts the fraction defective, etc.

D. Data point indices (1,2,...N) (I.A.G.D)
    - Labels the X-Axis with sequential integers beginning with
      1.  These integer indices coorespond to the indice you
      provide in the DISPLAY range (I.A.A), LIMITS range (I.A.B),
      and the STATS range (I.A.C).

Return
    - Return to the Control Chart Options (I.A) menu.
@
CC_Y_AXIS_MENU
A. none
B. UCL & LCL only
C. Graduated Scale
Return
@
CC_Y_AXIS_TEXT

@
CC_Y_AXIS_HELP
          Control Chart Y Axis Labeling Type Help (I.A.F)
                   [default: UCL & LCL]

You may select the type of label for the Y (Vertical) Axis.
Select from the following:


A. none (I.A.F.A)
    - Do not label the Y axis.


B. UCL & LCL only (I.A.F.B)
    - Label only the Centerline and the upper (UCL) and lower
      (LCL) control limits.  The values for the LCL and UCL
      will be part of these labels.


C. Graduated Scale (I.A.F.C)
    - Label the Center line, UCL, LCL, and intermediate values
      (one and two sigma) on the Y Axis.  The values will be
      part of these labels.


Return
    - Return to the Control Chart Options (I.A) menu.
@
CC_ZONES_MENU
A. none
B. UCL only
C. LCL only
D. UCL & LCL
E. zones
Return
@
CC_ZONES_TEXT

@
CC_ZONES_HELP
             Control Chart ZONEs Menu Help (I.A.G)
                     [default: UCL & LCL]

You may specify what control limit markings are plotted on the
control chart besides the center line.  Select from the following:

A. none (I.A.G.A)
    - Display the center line only.


B. UCL only (I.A.G.B)
    - Display the center line and UCL (upper control limit) only.


C. LCL only (I.A.G.C)
    - Display the center line and LCL (lower control limit) only.


D. UCL & LCL (I.A.G.D)
    - Display the center line, UCL (upper control limit) and
      LCL (lower control limit).


E. zones (I.A.G.E)
    - Display the center line, UCL (upper control limit), LCL
      (lower control limit), and the "1-sigma" and "2-sigma"
      lines above and below the center line.  These vertical
      ranges are often called "zones":

             -1 to +1 sigma                  :  ZONE C
             -2 to -1 sigma & +1 to +2 sigma :  ZONE B
             -3 to -2 sigma & +2 to +3 sigma :  ZONE A

Return
    - Return to the Control Chart Options (I.A) menu.
@
CC_MIN_PAT_LEN_MENU
A. run
B. inc_trend
C. dec_trend
D. shift_up
E. shift_down
F. cyclic
G. mixture
H. stratification
Return
@
CC_MIN_PAT_LENGTH_TEXT

@
CC_MIN_PAT_LEN_HELP
    Control Chart Analysis Minimum Pattern Lengths (I.A.M)
                  (defaults given below)

You may use this to set the minimum length required for each
control chart out-of-control condition to be reported after
the automatic control chart analysis (selection D).  Various
"Western Electric" type rules are applied to test for these
conditions which suggest the presence of un-natural causes of
variation in a process.


A. run (I.A.M.A) [default: 7]
    - A run is and sequence of points which all fall on the
      same side of the center line.  A process which is in
      control (only natural causes of variation) should have
      values randomly above and below the centerline.


B. inc_trend (I.A.M.B) [default: 7]
    - An increasing trend is a sequence of points for which
      each is higher/larger than the previous.  A process which
      is in control (only natural causes of variation) should
      have values which are randomly above and below the
      preceeding value.


C. dec_trend (I.A.M.C) [default: 7]
    - A decreasing trend is a sequence of points for which
      each is lower/smaller than the previous.  A process which
      is in control (only natural causes of variation) should
      have values which are randomly above and below the
      preceeding value.


D. shift_up (I.A.M.D) [default: 10]
    - A shift-up is a sequence of points for which the first half
      is below the center line and the second half is above the
      center line.  A process which is in control (only natural
      causes of variation) should have values which are randomly
      above and below the center line.


E. shift_down (I.A.M.E) [default: 10]
    - A shift-down is a sequence of points for which the first half
      is above the center line and the second half is below the
      center line.  A process which is in control (only natural
      causes of variation) should have values which are randomly
      above and below the center line.


F. cyclic (I.A.M.F) [default: 10]
    - A cycle is a sequence of points which alternate up and down.
      A process which is in control (only natural causes of variation)
      should have values which are randomly above and below the
      preceeding value.


G. mixture (I.A.M.G) [default: 10]
    - A mixture is a sequence of points which are more than 1 sigma
      above or below the center line.  A normally distributed process
      which is in control (only natural causes of variation) should
      have about 68% of its values within +- 1 sigma (standard
      deviation) of its average (mean).


H. stratification (I.A.M.H) [default: 10]
    - Stratification is a sequence of points which are all within
      +- 1 sigma of the center line.  A normally distributed process
      which is in control (only natural causes of variation) should
      have about 32% of its values more than 1 sigma (standard
      deviation) above or below its average (mean).


Return
    - Return to the Control Chart Options (I.A) menu.
@
DIST_OPTIONS_MENU
A. Show Process Specs ON/OFF
B. Eliminate Outliers ON/OFF
C. Show Mean ON/OFF
D. Show Median ON/OFF
E. Standard Dist Display
F. Number of Bins
Return to OPTIONS Menu
@
DIST_OPTIONS_TEXT

@
DIST_OPTIONS_HELP
            Distribution Graph Options Menu Help (I.B)


A. Show Process Specs ON/OFF (I.B.A) [default: OFF]
    - Use this selection to toggle ON/OFF the process
      specifications option for distribution graphs.  The
      process specifications for all tools is set using
      the PROCESS SPECIFICATIONS MENU (selection I.E).
      When ON, the process specifications will be displayed
      over the distribution graphic.  When SUMMARY STATS is
      turned ON (selection I.H.C) AND this is ON, capability
      statistics (Cp, Cpk, Cpu, Cpl, etc.) will be displayed
      in the statistics summary box on the graphic.


B. Eliminate Outliers ON/OFF (I.B.B) [default: OFF]
    - When this is ON, all data points marked as user defined
      outliers (e.g. !45 or ! 0.335) in the data file, will
      not be used to calculate any statistics or create the
      distribution graphic.


C. Show Mean ON/OFF (I.B.C) [default: OFF]
    - When this is ON, the mean (average) of the data values
      will be overlaid on the distribution graphic.


D. Show Median ON/OFF (I.B.D) [default: OFF]
    - When this is ON, the median of the data values will be
      overlaid on the distribution graphic.


E. Standard Dist Display (I.B.E) [default: none]
    - You may overlay a standard frequency distribution function
      on the distribution graphic.


        A.  None.  Does not overlay a frequency distribution.
        B.  Uniform (best guess)*
        C.  Exponential (best guess)*
        D.  Normal (best guess)*
        E.  LogNormal (best guess)*
        F.  Gamma  (best guess)  Not available.
        G.  Uniform(a,b)
        H.  Exponential(mu)
        I.  Normal(mu, sigma)
        J.  LogNormal(mu,sigma)
        K.  Gamma(alpha, theta) Not available.
        L.  Weibull(1,beta,gamma)

          (* Best guess is based on estimates calculated from
             the data in the data files.)


F. Number of Bins (I.B.F) [default: auto]
    - You may select how many data groups or bins are used to
      arrange the data.  The maximum is 20, minimum 1, and an
      auto select option is provided/recommended.


Return
    - Return to the Options (selection I) menu.
@
DIST_DIST_MENU
A. none
B. Uniform     (best guess)
C. Exponential (best guess)
D. Normal      (best guess)
E. LogNormal   (best guess)
F. Gamma       (best guess)
G. Uniform(a,b)
H. Exponential(mu)
I. Normal(mu,sigma)
J. LogNormal(mu,sigma)
K. Gamma(alpha,theta)
L. Weibull(1,beta,gamma)
Return
@
DIST_DIST_TEXT

@
DIST_DIST_HELP
Distribution Graphs Overlaid Frequency Distribution Type Help (I.B.E)
                       [default: none]


You may overlay a standard frequency distribution function on the
distribution graphic.  The following functions are available:


        A.  None.  Does not overlay a frequency distribution.
        B.  Uniform (best guess)*
        C.  Exponential (best guess)*
        D.  Normal (best guess)*
        E.  LogNormal (best guess)*
        F.  Gamma  (best guess)  Not available.
        G.  Uniform(a,b)  where
            a = Uniform distribution lower limit
            b = uniform distribution upper limit.
        H.  Exponential(mu) where
            mu = mean.
        I.  Normal(mu, sigma) where
            mu = mean
            sigma = standard deviation of n-1.
        J.  LogNormal(mu,sigma) where
            mu = mean of the natural logarithms
            sigma = standard deviation of n-1 for the natural
            logarithms.
        K.  Gamma(alpha, theta) Not available.
        L.  Weibull(1,beta,gamma) where
            1 = scaling factor
            beta = shape parameter
            gamma = start position.

(* Best guess is based on estimates calculated from the data in the
   data files.)

M. Return
    - Return the the distribution graph options (I.B) menu.

@
DIST_BINS_MENU
A. Auto Select
B. User Defined
Return
@
DIST_BINS_TEXT

@
DIST_BINS_HELP
              Distribution Graph # Bins Help (I.B.F)
                         [default: Auto]

You may select how many data groups or bins are used to
arrange the data.  The maximum is 20, minimum 1, and an
auto select option is provided/recommended.

@
PIE_OPTIONS_MENU
A. Data Label Type
Return to Options Menu
@
PIE_OPTIONS_TEXT

@
PIE_OPTIONS_HELP
      PIE, BAR, PARETO Options Help (I.C)

This menu allows you to affect how the PIE, BAR,
PARETO, and TABLE charts appear.

A. Data Label Type (I.C.A) [default: frequency]
    - This allows you to specify how the PIE, BAR,
      PARETO, and TABLE charts are labeled with
      the data values.

Return
    - Return to the Options (selection I) menu.

@
PIE_DATA_LABEL_MENU
A. none
B. frequency
C. percentage
Return
@
PIE_DATA_LABEL_TEXT

@
PIE_DATA_LABEL_HELP
     PIE, BAR, PARETO Data Labeling Type Help (I.C.A)
                [default: frequency]


This allows you to specify how the PIE, BAR, PARETO,
and TABLE charts are labeled with the data values.

A. none (I.C.A.A)
    - This eliminates the data labels from the output.

B. frequency (I.C.A.B)
    - This labels the bar or slice with the actual number
      of occurances for each data group.

C. percentage (I.C.A.C)
    - This labels the bar or slice with the percent of
      total represented by each data group.

Return
    - Return the PIE/BAR/PARETO/TABLE option menu (I.C)
@
SCATTER_OPTIONS_MENU
A. Show X Process Specs ON/OFF
B. Show Y Process Specs ON/OFF
C. Eliminate Outliers ON/OFF
D. Show X Mean ON/OFF
E. Show X Median ON/OFF
F. Show Y Mean ON/OFF
G. Show Y Median ON/OFF
H. Regression Line ON/OFF
I. Data Dist Graph Menu
Return to OPTIONS Menu
@
SCATTER_OPTIONS_TEXT

@
SCATTER_OPTIONS_HELP
               Scatter Diagram Options Help (I.D)


This allows you to set parameters which affect the statistical
calculations and appearance of SCATTER DIAGRAMS.  The following
choices are available:


A. Show X Process Specs ON/OFF (I.D.A) [default: OFF]
    - This allows you to plot (or not) the X Process specifications
      on the scatter diagram.  You can set the X process specs
      using the PROCESS SPECIFICATIONS menu (selection I.E).
      X Capability statistics (Cp, Cpk, Cpl, Cpu, etc.) are displayed
      when both Process Specs (I.D.A) is ON and Summary Stats (I.H.C)
      is ON.


B. Show Y Process Specs ON/OFF (I.D.B) [deault: OFF]
    - This allows you to plot (or not) the Y Process specifications
      on the scatter diagram.  You can set the Y process specs
      using the PROCESS SPECIFICATIONS menu (selection I.E).
      Y Capability statistics (Cp, Cpk, Cpl, Cpu, etc.) are displayed
      when both Process Specs (I.D.A) is ON and Summary Stats (I.H.C)
      is ON.


C. Eliminate Outliers ON/OFF (I.D.C) [deault: OFF]
    - You can designate any data points in the data file for the
      scatter diagram as "outliers" (e.g. ! 25 10, etc.).  When
      eliminate outliers is ON, points defined as outliers will be
      highlighted and will not be used in the calculations.


D. Show X Mean ON/OFF (I.D.D) [deault: OFF]
    - You may choose to plot or not the mean (average) of the X
      values on the scatter diagram.


E. Show X Median ON/OFF (I.D.E) [deault: OFF]
    - You may choose to plot or not the median of the X values
      on the scatter diagram.


F. Show Y Mean ON/OFF (I.D.F) [deault: OFF]
    - You may choose to plot or not the mean (average) of the Y
      values on the scatter diagram.


G. Show Y Median ON/OFF (I.D.G) [deault: OFF]
    - You may choose to plot or not the median of the Y values
      on the scatter diagram.


H. Regression Line ON/OFF (I.D.H) [deault: OFF]
    - This option allows you to plot (or not) the linear regression
      line calculated from the data points in the data file.
      Regression statistics (r-squared, F-test, t-test, regression
      coefficients, etc.) are displayed when both Scatter Diagram
      regression (I.D.H) is ON and Summary Stats (I.H.C) is ON.


I. Data Dist Graph Menu (I.D.I) [default: none]
    - This feature allows you to select a data distribution function
      (HISTOGRAM, POLYGON, or CDF) to display along with the scatter
      diagram.  Two distribution graphics are displayed -  one for
      the X values and one for the Y values.


Return to OPTIONS Menu


@
SCATTER_DIST_MENU
A. none
B. Histogram
C. Frequency Polygon
D. Ogive (CDF)
Return
@
SCATTER_DIST_TEXT

@
SCATTER_DIST_HELP
      Scatter Diagram Distribution Graph Type Help (I.D.I)
                       [default: none]

This feature allows you to select a data distribution function
(HISTOGRAM, POLYGON, or CDF) to display along with the scatter
diagram.  Two distribution graphics are displayed -  one for
the X values and one for the Y values.


A. none
    - No distribution graphs are displayed with the scatter
      diagram.

B. Histogram
    - Two HISTOGRAMS are displayed with the scatter diagram.


C. Frequency Polygon
    - Two frequency POLYGONS are displayed with the scatter
      diagram.


D. Ogive (CDF)
    - Two ogives (CDFs) are displayed with the scatter diagram.


Return
    - Return the the SCATTER diagram options menu (I.D).

@
SPECS_OPTIONS_MENU
A. USL
B. LSL
C. Nominal
D. USL (Y) Scatter Only
E. LSL (Y) Scatter Only
F. Nominal (Y) Scatter Only
G. Pop Sigma Est. Type
Return to OPTIONS Menu
@
SPECS_OPTIONS_TEXT

@
SPECS_OPTIONS_HELP
                Process Specifications Menu Help (I.E)

Use this menu to set the process specifications and method for
estimating the population standard deviation for all control
charts, distribution graphics, and scatter diagrams.  These
process specifications are saved with all of the other options.
Select from the following options:


A. USL (I.E.A) [default: 0.0]
    - Use this to set the USL for all control charts, Histograms,
      Polygons, CDFs (Ogives), and the X variable on scatter
      diagrams.  Any number from -10^7 to +10^7 may be entered.

B. LSL (I.E.B) [default: 0.0]
    - Use this to set the LSL for all control charts, Histograms,
      Polygons, CDFs (Ogives), and the X variable on scatter
      diagrams.  Any number from -10^7 to +10^7 may be entered.

C. Nominal (I.E.C) [default: 0.0]
    - Use this to set the nominal process value for all control
      charts, Histograms, Polygons, CDFs (Ogives), and the X
      variable on scatter diagrams.  Any number from -10^7 to
      +10^7 may be entered.

           *** This is not used in this version of SPC EXpert.

D. USL (Y) Scatter Only (I.E.D) [default: 0.0]
    - Use this to set the USL value for the Y variable on scatter
      diagrams.  Any number from -10^7 to +10^7 may be entered.


E. LSL (Y) Scatter Only (I.E.E) [default: 0.0]
    - Use this to set the LSL value for the Y variable on scatter
      diagrams.  Any number from -10^7 to +10^7 may be entered.


F. Nominal (Y) Scatter Only (I.E.F) [default: 0.0]
    - Use this to set the nominal process value for the Y variable
      on scatter diagrams.  Any number from -10^7 to +10^7 may
      be entered.

           *** This is not used in this version of SPC EXpert.


G. Pop Sigma Est. Type (I.E.G) [default: sigma(n-1)]
    - You may select the method used to estimate the population
      standard deviation when calculating capability statistics.


Return to OPTIONS Menu

@
POP_SIGMA_EST_MENU
A. Table Lookup
B. Pop Sigma(n)
C. Pop Sigma(n-1)
D. User Defined
@
POP_SIGMA_EST_TEXT
@
POP_SIGMA_EST_HELP
 Population Standard Deviation Estimate Method Help (I.E.G)
                [default: Pop Sigma(n-1)]

You may select the method used to estimate the population
standard deviation when calculating capability statistics.
The following options are available:


A. Table Lookup (I.E.G.A)
    - This method approximates the standard deviation of the
      population using statistical tables or formulas commonly
      cited in textbooks.

B. Pop Sigma(n) (I.E.G.B)
    - This method approximates the standard deviation of the
      population using the standard deviation of the individual
      samples with n degrees of freedom.

C. Pop Sigma(n-1) (I.E.G.C)
    - This method approximates the standard deviation of the
      population using the standard deviation of the individual
      samples with n-1 degrees of freedom.

D. User Defined (I.E.G.D)
    - This method allows you to directly specify the standard
      deviation of the population.  This method is NOT
      RECOMMENDED!  Use at your own risk.
@
RAW_DATA_OPTIONS_MENU
A. SPC EXpert Format
B. USAF SPC 1.1 Format
C. USAF SPC 1.2 Format
Return to OPTIONS Menu
@
RAW_DATA_OPTIONS_TEXT

@
RAW_DATA_OPTIONS_HELP
              Data File Format Type help (I.F)
                [default: SPC EXpert Format]

This option allows you to select the version format of data files
imported.  This option is included to allow for both the extension
of SPX EXpert data file formats and to allow in the future,
additional formats which can be imported into SPC EXpert such as
DBase-type files, etc.  The following data file formats are supported:


A. SPC EXpert Format (I.F.A)
    - This is the data file format described in the SPC EXpert
      software users manual.


B. USAF SPC 1.1 Format (I.F.B)
    - This is the data file format used in the Air Force's Statistical
      Process Control Software (SPC Version 1.1 - March 1992).  SPC
      Version 1.1 is available only to Department of Defense Agencies.

C. USAF SPC 1.2 Format (I.F.C)
    - This is the data file format used in the Air Force's Statistical
      Process Control Software (SPC Version 1.2 - October 1992).  SPC
      Version 1.2 is available only to Department of Defense Agencies.

          *** SPC EXpert's data file formats were patterned directly
              after the USAF SPC 1.2 raw data file formats.
@
FONTS_OPTIONS_MENU
A. Titles Font
B. Titles Font Size
C. Axes Labels Font
D. Axes Labels Font Sizes
Return to OPTIONS Menu
@
FONTS_OPTIONS_TEXT

@
FONTS_OPTIONS_HELP
                     FONTS Options Help (I.G)


You may select the font and font size for both the Titles/Subtitles
and X and Y Axis labels.  The following options are available:

A. Titles Font (I.G.A) [default: Stroked Small]
    - You may select the type of text font used in the title and
      subtitle of all graphics.  The following fonts are available:

                 A. 8x8 bit-mapped
                 B. Stroked triplex
                 C. Stroked small
                 D. Stroked sans-serif
                 E. Stroked gothic


B. Titles Font Size (I.G.B) [default: Auto]
    - You may select the type of text font used in the title and
      subtitle of all graphics.  The sizes available include:
      "0. Auto" or "1 - 10".  "Auto" selects the font size to fit
      the title length to the screen width and height.  "1" - "10"
      determines the relative size of the font from small ("1") to
      large ("10").

C. Axes Labels Font (I.G.C) [default: Stroked Small]
    - You may select the type of text font used in the X and Y axis
      labels of all graphics.  The following fonts are available:

                 A. 8x8 bit-mapped
                 B. Stroked triplex
                 C. Stroked small
                 D. Stroked sans-serif
                 E. Stroked gothic


D. Axes Labels Font Sizes (I.G.D) [default: Auto]
    - You may select the type of text font used in the X and Y axis
      labels of all graphics.  The sizes available include:
      "0. Auto" or "1 - 10".  "Auto" selects the font size to fit
      the title length to the screen width and height.  "1" - "10"
      determines the relative size of the font from small ("1") to
      large ("10").

Return to OPTIONS Menu

@
DISPLAY_OPTIONS_MENU
A. Titles ON/OFF
B. Enhanced Print ON/OFF
C. Summary Stats ON/OFF
D. Sound ON/OFF
Return to OPTIONS Menu
@
DISPLAY_OPTIONS_TEXT

@
DISPLAY_OPTIONS_HELP
         General Display Characteristics Help (I.H)

This allows you to set parameters which affect all types of
charts and diagrams.  These include:


A. Titles ON/OFF (I.H.A) [default: ON]
    - Use this option to toggle ON/OFF the display of the Title
      and subtitle for all charts and diagrams.


B. Enhanced Print ON/OFF (I.H.B) [default: OFF]
    - Use this option to toggle ON/OFF the display of detailed
      information for all charts and diagrams.  This information
      includes such things as file name, file date, chart type,
      print date, etc.


C. Summary Stats ON/OFF (I.H.C) [default: OFF]
    - Use this option to toggle ON/OFF the display of a summary
      statistics box on the graphic of all charts and diagrams.

      *** This option must be ON to view any of the specialized
          statistics such as regression and capability stats.


D. Sound ON/OFF (I.H.D) [default: ON]
    - Use this option to toggle ON/OFF the sound (beeps) in SPCEX.


Return to OPTIONS Menu

@
SAVE_CFG_OPTIONS_MENU
A. Save Options for Start-ups
B. Save Options to File
C. Load Start-up Options
D. Load Options from File
E. Reset Options to Defaults
Return to OPTIONS Menu
@
SAVE_CFG_OPTIONS_TEXT
@
SAVE_CFG_OPTIONS_HELP
             Save\retrieve Options File Help (I.I)

Current and past settings for options may be saved and recalled
for future use using this menu.  In particular, you can use this
menu to save the current options settings to a named (provided
by you) file (I.I.B) which can be later specifically referenced
in a data file ( *<file-name> on first line ).

A. Save Options for Start-ups (I.I.A)
    - This feature saves the current option settings to a default
      "options file" which is loaded every time you start the program.
      The default options file contains the option default settings
      until you chang it using this option (I.I.A).


B. Save Options to File (I.I.B)
    - Current option settings may also be saved to an "options file"
      named by you.  This file can be used with Multiple Chart files
      to display the output using the specified options file.  If the
      special "options file" is to be used for all charts/graphs in
      the Multiple Chart, the filename would appear in the first line
      with an asterisk next to it.  For example, if the special "options
      file" is called "myopts.cfg", a Multiple Chart file may look like
      this:

                    *myopts.cfg
                    Title
                    Subtitle
                    GPA.DAT BAR
                    GPA.DAT PARETO
                    GPA.DAT PIE

      If the special "options file" is to be used for a specific chart
      or graph the file name is entered after the chart type.  The
      Multiple Chart data file may look like this:

                    Title
                    Subtitle
                    GPA.DAT BAR
                    GPA.DAT PARETO myopts.cfg
                    GPA.DAT PIE


C. Load Start-up Options (I.I.C)
    - Use this to load the Start-up options file.  This is the file
      updated using selection (I.I.A).


D. Load Options from File (I.I.D)
    - Current options settings may also be saved to an "Options" file
      that you name/create (I.I.B).  Use this option to load a
      user-defined options file.


E. Reset Options to Defaults (I.I.E)
    - You may also easily reset all the options to the original SPCEX
      software default settings using this selection.  This is
      particularly useful if you have changed a lot of options and
      want to start over with the default settings.

      ***  This does not affect the options settings in the Start-up
           options file that are loaded when the program is re-started.
           You must save the default settings (I.I.A) after resetting
           the options to their defaul to change the start-up settings.
@
FONT_TEXT
Select a font for
titles & subtitles
@
FONT_MENU
A. 8x8 bit-mapped
B. Stroked triplex
C. Stroked small
D. Stroked sans-serif
E. Stroked gothic
Return
@
FONT_HELP
        FONT Definition Help Screen

This choice is a matter of personal taste.  The SPCEX
system default is B. Stroked triplex.
@
TEXT_TEXT
Select a font for
Non-Titles Text
@
TEXT_HELP
Non-Titles FONT Definition Help Screen  -  Not Developed Yet.

This choice is a matter of personal taste.  The SPCEX
system default is A. 8x8 Bit mapped.
@
FONTSIZE_MENU
0 (Auto)
1
2
3
4
5
6
7
8
9
10
Return
@
FONTSIZE_TEXT
Select a text size scaling factor.
@
FONTSIZE_HELP
   Titles Text size scaling factor Help Screen


This choice is a matter of personal taste.  The SPCEX
system default is 0 Automatic scaling.
@
EDIT_TEXT
Select a File Manager Option
@
EDIT_MENU
A. Edit Current Data File
B. Create/Edit A File
C. View A File
D. Copy A File
E. Rename A File
F. Delete A File
Return to MAIN MENU
@
EDIT_HELP
     SPC EXpert Editor & File Manager

SPC EXpert provides you with an integrated editor to
create or modify data files.  The editor is currently
limited to a maximum of 16000 lines by 70 columns.

SPC EXpert also provides the file management functions to
VIEW, COPY, RENAME, and DELETE a file.
@
editor_quest
Enter the name of the
file you wish to edit.
@
demo_help
            STATISTICAL PROCESS CONTROL SOFTWARE

                       SPC EXpert

Developed by:

               Quality Software Designs, Inc.
                  933 East Stroop Road
                 Kettering, Ohio 45429

                  DEMONSTRATION PROGRAM

Several Sample data sets (options C - Y) have been included
for demonstration purposes.  Option B is a repeating display
of all of the graphs/diagrams produced by SPCEX.  Option A
allows you to use SPC EXpert with your own data. Select
the last option to quit.

The following ASCII files contain the sample data :

               (C) #trun.dmo#t
                      #u<graphic>;RUN run.dmo default.cfg#u RUN Chart
               (D) #tr.dmo#t
                      #u<graphic>;XBAR r.dmo default.cfg#u XBAR Chart
               (E) #tr.dmo#t
                      #u<graphic>;R r.dmo default.cfg#u R Chart
               (F) #ts.dmo#t
                      #u<graphic>;S s.dmo default.cfg#u S Chart
               (G) #trun.dmo#t
                      #u<graphic>;MR run.dmo default.cfg#u MR Chart
               (H) #tr.dmo#t
                      #u<graphic>;XBAR_R r.dmo default.cfg#u XBAR_R Chart
               (I) #ts.dmo#t
                      #u<graphic>;XBAR_S s.dmo default.cfg#u XBAR_S Chart
               (J) #trun.dmo#t
                      #u<graphic>;XMR run.dmo default.cfg#u XMR Chart
               (K) #tp.dmo#t
                      #u<graphic>;P p.dmo default.cfg#u P Chart
               (L) #tpn.dmo#t
                      #u<graphic>;PN pn.dmo default.cfg#u PN Chart
               (M) #tc.dmo#t
                      #u<graphic>;C c.dmo default.cfg#u C Chart
               (N) #tu.dmo#t
                      #u<graphic>;U u.dmo default.cfg#u U Chart
               (O) #tbar.dmo#t
                      #u<graphic>;BAR bar.dmo default.cfg#u Bar Graph
               (P) #tbar.dmo#t
                      #u<graphic>;PARETO bar.dmo default.cfg#u PARETO Diagram
               (Q) #tbar.dmo#t
                      #u<graphic>;PIE bar.dmo default.cfg#u PIE Chart
               (R) #tbar.dmo#t
                      #u<graphic>;TABLE bar.dmo default.cfg#u TABLE Chart
               (S) #trun.dmo#t
                      #u<graphic>;HISTOGRAM run.dmo default.cfg#u HISTOGRAM
               (T) #trun.dmo#t
                      #u<graphic>;POLYGON run.dmo default.cfg#u frequency POLYGON
               (U) #trun.dmo#t
                      #u<graphic>;CDF run.dmo default.cfg#u CDF
               (V) #tscat.dmo#t
                      #u<graphic>;SCATTER scat.dmo default.cfg#u SCATTER DIAGRAM
               (W) #tmulti3.dmo#t
                      #u<graphic>;MULTIPLE multi3.dmo default.cfg#u MULTIPLE CHART
               (X) #tmulti2.dmo#t
                      #u<graphic>;MULTIPLE multi2.dmo default.cfg#u MULTIPLE CHART
               (Y) #tmulti1.dmo#t
                      #u<graphic>;MULTIPLE multi1.dmo default.cfg#u MULTIPLE CHART
@
WAIT_MESSAGE
One Moment Please ...

    Loading SPC EXpert


Quality Software Designs, Inc.
933 East Stroop Road
Kettering, Ohio 45429
@
DEMO_MENU
A. SPC EXpert Tool
B. Screen Show
C. Run Chart
D. Xbar Chart
E. R Chart
F. S Chart
G. Moving Range Chart
H. Xbar-R Chart
I. Xbar-S Chart
J. X Moving Range Chart
K. P Chart
L. PN Chart
M. C Chart
N. U Chart
O. Bar Chart
P. Pareto Diagram
Q. Pie Chart
R. Table
S. Histogram (Frequency Dist)
T. Frequency Polygon
U. Ogive (CDF)
V. Scatter Diagram
W. Multiple Chart
X. Multiple Chart
Y. Multiple Chart
exit demonstration
@
DEMO_TEXT
     SPC EXpert
   DEMONSTRATION


Quality Software Designs, Inc.
933 East Stroop Road
Kettering, Ohio 45429
messages: [phone]
email:    [e-mail]
       ...!uunet!meaddata!marks

Select a Sample data set  ->
@
DEMO_DEMO_TEXT
SPC EXpert DEMONSTRATION


For a fully functional registered
copy of SPC EXpert, send the
appropriate licensing fees to


Quality Software Designs, Inc.
933 East Stroop Road
Kettering, Ohio 45429


Select a Sample data set  ->
@
DEMO_TYPE_FILES
RUN run.dmo
XBAR r.dmo
R r.dmo
S s.dmo
MR run.dmo
XBAR_R r.dmo
XBAR_S s.dmo
XMR run.dmo
P p.dmo
PN pn.dmo
C c.dmo
U u.dmo
BAR bar.dmo
PARETO bar.dmo
PIE bar.dmo
TABLE bar.dmo
HISTOGRAM run.dmo
POLYGON run.dmo
CDF run.dmo
SCATTER scat.dmo
MULTIPLE multi3.dmo
MULTIPLE multi2.dmo
MULTIPLE multi1.dmo
@
VIDEO_OPTIONS_MENU
A. Auto Detect (Recommended)
B. CGA LOW 320x200
C. CGA HIGH 640x200
D. MCGA LOW 320x200
E. MCGA MED 640x200
F. MCGA HIGH 640x480
G. EGA LOW 640x200
H. EGA HIGH 640x350
I. EGA64 LOW 640x200
J. EGA64 HIGH 640x350
K. HERCULES MONO 720x348
L. ATT400 LOW 320x200
M. ATT400 MED 640x200
N. ATT400 HIGH 640x400
O. VGA LOW 640x200
P. VGA MED 640x350
Q. VGA HIGH 640x480
R. PC3270 720x350
S. IBM8514 LOW 640x480
T. IBM8514 HIGH 1024x768
return
@
VIDEO_OPTIONS_TEXT
@
VIDEO_OPTIONS_HELP
This option is only recommended if you
are haveing problems displaying graphics
on you monitor.

A. Auto Detect - is RECOMMENDED!
@
MENU_NOTATION
                 (X.Y.Z) MENU NOTATION

The documentation and HELP screens in SPC EXpert use a special
notation to specify a sequence of menu selections beginning
from the MAIN MENU.  This notation will simplify instructions
for navigating through the SPC EXpert menus.


For example, to view the current options settings, you
would select (I.J) by

     1. Start From SPCEX MAIN MENU
     2. Select item I, "I. Options"
          - Now you are in the OPTIONS MENU
     3. Select item J, "J. Display Current Options"


Another example, to set the method of computing a control chart
center line to "Median", you would select (I.A.D.B) by

     1. Start From SPCEX MAIN MENU
     2. Select item I, "I. Options"
          - Now you are in the OPTIONS MENU
     3. Select item A, "A. Control Charts"
          - Now you are in the CONTROL CHART OPTIONS MENU
     4. Select item D, "D. Center Line Method"
     5. Select item B, "B. Median"

@
EDITOR_HELP
                     SPC EXpert EDITOR

<F1>      - Help                   <RETURN>     - Insert Line
                                             (When Insert Is ON)
|         - Up 1 line              <F4> - Data File Formats
|         - Down 1 line
-         - Right 1 Character      <F3>         - Delete Line
-         - Left 1 Character       Delete       - Delete Char
                                   Backspace    - Delete Previous
PgUp      - Up one page                           Char
PgDn      - Down one page
                                      Insert    - Toggle Between
Home      - Beginning of Line                     Insert Mode and
End       - End of Line                           Overwrite Mode

<F2>      - Save File and Exit           Maximum Lines/Rows :
Esc       - Exit Without Save            Maximum Columns    :
@
TRANSFER_FILES
bar.dmo
run.dmo
default.cfg
notitles.cfg
@
SHELL_COMMAND
command.com
@