home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
Cubeat 2.0
/
CUBEAT.ima
/
README
< prev
next >
Wrap
Text File
|
1991-08-08
|
4KB
|
157 lines
STEINBERG SOFT & HARDWARE
This CUBEAT version 2.0 is compatible with the ATARI MEGA STE; it
can be run both in 8 and 16 Megahertz operating modes, but it is
absolutely necessary to disable the cache!
Please read the following instructions:
I. Synchronization with MROS 2.15
II. SWITCHER 3.03 with MIDEX / MIDEX +
III. KEYSLOT - Accessory for MIDEX / MIDEX +
IV. Using BIGSCREEN Monitors
I. Synchronizing with MROS 2.15
Cycle can now be switched without stop in CUBEAT. Note that this
probably will not work with other MROS realtime programs (Tentrax,
DDD etc) which use cycle mode. These should use MROS 2.10.
It does not affect synth/sample editors.
It has been found that there is a different SMPTE offset between
SMP24 and MIDEX+. You will have to change the SMPTE Start Time
when you want to use MIDEX+ for a production made with the
SMP24 and vice versa.
Here is a table which shows how to set the SMPTE Start Time for
productions that you already have on tape. You will only need to
adjust the time if you have already recorded something, for new
productions you can set the SMPTE Start Time as usual (all examples
related to 25 frames).
1. If you recorded with MROS 2.11 (using the same device) subtract
40 subframes:
Start Time was: 00:01:00:00:00
set to: 00:00:59:24:40
2. If you recorded with MIDEX+ and want to use SMP24 or
TIMELOCK with that tape add 100 subframes (1 frame + 20
subframes):
Start Time for MIDEX+ : 00:01:00:00:00
for SMP24 or TIMELOCK : 00:01:00:01:20
3. If you recorded with SMP24 or TIMELOCK and want to use that
tape with MIDEX+ subtract 100 subframes (1 frame + 20 subframes):
Start Time for SMP24 or TIMELOCK: 00:01:00:00:00
for MIDEX+: 00:00:59:23:60
Proper MTC similar to MIDEX+.
II. SWITCHER 3.03
With STEINBERG programs like CUBASE, CUBEAT, TWENTY FOUR,
SYNTHWORKS, AVALON, MIMIX etc it doesn't matter in which order
you plug in the keys in the MIDEX - slots because the keys are
recognized by the SWITCHER automatically.
However, when using the SWITCHER and MIDEX with
NON-STEINBERG products the Function- keys are now related to the
corresponding MIDEX - slots:
F 1 .... MIDEX - Slot 1
F 2 .... MIDEX - Slot 2
F 3 .... MIDEX - Slot 3
F 4 .... MIDEX - Slot 4
F 5 .... MIDEX - Slot 1
F 6 .... MIDEX - Slot 2
etc.
If you don`t want to use the SWITCHER take the
III. KEYSLOT - Accessory
( KEYSLOT.ACC, installing with INSTALL.PRG )
by clicking on "NEXT SLOT" ( "DESK" Menu ) you can switch
between the MIDEX - slots.
IV. Using BIGSCREEN Monitors:
When a Bigscreen Monitor is connected and CUBEAT is loading, there
will be a box that displays a VDI or a QUICK driver. Depending on
the monitor you use, check out which driver will run with CUBEAT.
QUICK is only for monochrom monitors.
The monitors MATRIX M110 and ATARI SM 194 use the QUICK driver.
Arno Fisser
Steinberg
Soft & Hardware GmbH