home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
Der Mediaplex Sampler - Die 6 von Plex
/
6_v_plex.zip
/
6_v_plex
/
DISK3
/
DFUE_25
/
BGFAX110.ZIP
/
HELPME.ZIP
/
BINKLEY.TXT
< prev
next >
Wrap
Text File
|
1994-01-04
|
3KB
|
112 lines
Note by BGFAX author...
Binkley 2.59 does exit with a fax result code occurs. However, it appears
to take 2 seconds to exit even on my 386DX40. This may be pushing the
timing too critical for BGFAX to get the line. There should really only be
a very short less than 1 second delay when the host program exits. If this
is not corrected, I suggest using the internal Binkley fax routines rather
than BGFAX.
Original text by Art Geary follows (for Binkley 2.56)
-----------------------------------------------------------------------------
BinkleyTerm and PPI 14400FXSA Fax
I have run Binkley for a number of years, and act as the mail hub for my
Net. I did not want to change to some other mailer. I also bought a
Practical Peripherals 14400FXSA modem, and wanted to be able to continue to
do my mail and recieve fax's on the same line.
There seemed to be no way to do it. Then along came BGFax. This program can
either Front-end or Rear-end a BBS. Thank you B.J. Guillot.
Here is my cludge....
1. Set up BGFax to Front end. See BGFAX.CNF.
Event times are set 1 minute before my Binkley.evt file
times.
2. Add 'Server' verb to Binkley.cfg.
3. Tweak Binkley batch file. See BINK.BAT.
Works fine here on 16MHz 386SX.
Only bad thing is that the %'s on transfer rate will be wrong if BGFAX
answers phone.
BGFAX.CNF
po=1
ft=q
sp=19200
in=ATZ
in=AT+FCR=1;+FLID="713 893 9124";+FDCC=1,5,0,2,0,0,0
in=ATM0
ri=1
an=AT+FAA=1;A
do=<load>
lo=
ec=/ARQ
sl=300
ts=Calls are not accepted below 1200 bps. Sorry.
cm=CQ,104
ev=23:59,124
ev=00:29,123
ev=01:59,122
ev=03:59,121
ev=04:59,120
ev=05:49,119
ev=06:29,118
ev=06:59,117
ev=21:58,115
ev=22:58,116
BINK.BAT
c:
cd \max
cls
vfos_ibm
echo off
:start
:chkcra
REM IF CRASH MAIL WAITING TO GO OUT, BYPASS BGFax
if exist \max\outbound\*.cl* goto loop
:bfax
bgfax
if errorlevel 124 goto loop
if errorlevel 123 goto loop
if errorlevel 122 goto loop
if errorlevel 121 goto loop
if errorlevel 120 goto loop
if errorlevel 119 goto loop
if errorlevel 118 goto loop
if errorlevel 117 goto loop
if errorlevel 116 goto loop
if errorlevel 115 goto loop
if errorlevel 4 goto start
if errorlevel 3 goto loop
if errorlevel 2 goto loop
if errorlevel 1 goto start
if errorlevel 0 goto end
goto chkcra
:loop
erase lastuse1.bbs
btbig unattended share
if errorlevel 192 goto max192
ETC...
All routines in the batch file end with goto start.
Errorlevels 124 - 115 corespond the errorlevels set in BGFAX.CNF.
I also made my F1 key in Binkley (errorlevel 10) goto bfax to enable a fax
recieve manually.
Any questions or suggestions to...
Art Geary
1:393/101@fidonet
(817) 321-3213 Fax 07:00 - 22:00 CDT Data 24 hrs.
(817) 321-3903 Voice