home *** CD-ROM | disk | FTP | other *** search
/ The Unsorted BBS Collection / thegreatunsorted.tar / thegreatunsorted / texts / pirate_radio / pro34 < prev    next >
Text File  |  1991-10-22  |  10KB  |  203 lines

  1. REALISTIC PRO34 MODS & INFO
  2.  
  3. "NOVICE NOTES" FOR PRO-34 MODIFICATIONS
  4.  
  5. 1.  Remove the 4 small phillips scres on the back of the unit
  6.  
  7. 2.  Remove the batter cover and battery holder from the case.
  8.  
  9. 3.  Remove the two knobs on the top of the case (Volume &  Squelch)
  10.  
  11. 4.  The Case has some pressure fit points, These are at the bottom of
  12.     the case and you need to be a bit careful in forcing the two halves
  13.     of the case shell appart. Once you have the pressure fit points 
  14.     at the bottom released, angle up the bottom of the case until
  15.     the battery sepperation wall is clear of the internal metal frame, and 
  16.     slide towards the top of the unit, place the back half of the shell aside.
  17.  
  18. 5.  Now you will see the RF boad mounted to the metal support frame, The 
  19.     BNC (antenna) conector leads and the volume control power switch leads
  20.     are soldered directly to the board. Carefully desolder these 4 connections.
  21.  
  22. 6.  At the bottom of the RF board there is a IF Can transformer that has a small
  23.     wire as a groundign strap soldered directly to it. Desolder this as well.
  24.  
  25. 7.  There will be some wires from the volume controle knob to the PC board that
  26.     are socketed. Remove the plug from the ~F board (needle nose pliers work)
  27.  
  28. 8.  There will also be a similar wire (small sheilded ) from the squelch control
  29.     to the RF board wich is also Socketed. Remove the plug from the RF board.
  30.     (Again Needle Nose Pliers work good here)
  31.  
  32. 9.  Remove the 4 thredded stand-offs from the RF Board (these Hold the RF board to
  33.     the internal mettal frame and are where the screws that hold the back of the
  34.     case on go.) Use a nut driver or Needle Nose Pliers.
  35.  
  36. 10. Now there the RF board is mostly free. The only thing holding it in is the row
  37.     of connector pins on its botom side that plug into the logic board. You will
  38.     need to pry this board up gently. Be warned that the bottom side of the RF 
  39.     board is just chock full of Very Small surface mounted omponents. So use 
  40.     something non-metalic and smooth to do the prying with.
  41.  
  42. 11. Now that you have removed the RF board, place it along with the case shell back
  43.  
  44. 12. The Internal Metal support frame is now exposed. there are 3 small phillips
  45.     screws holding the mettal frame to the bottom Logic board (actually, these
  46.     screws go through the logic board and into the front half of the case.)
  47.     2 of the screws are near the top, and 1 is at the bottom of the metal frame.
  48.     remove these 3 screws.
  49.  
  50. 13. There is a small socketed wire that leads from the small power pc board on the
  51.     metal frame that goes under it and is pluged into the Logic board. Lift
  52.     the metal frame up and remove the power plug from the PC board. Place the 
  53.     metal frame with|the rest of your parts pile.
  54.  
  55. 14. You are have the component side of the  Logig board exposed now. There are
  56.     2 small phillips screws at the bottom of the PC board (where the Battery 
  57.     compartment WAS) Remove them.
  58.  
  59. 15. Once you have the the last 2 screw removed the Logic board is free. The
  60.     speaker wires lead from the speaker to the logic board on the bottom side.
  61.     These are soldered in but there is enough play in them to allow you to
  62.     make the mods.
  63.  
  64. 16. NOTE: The keyboard lock switch is a funky little piece of plastic with
  65.     a sliding stainless metal contactor that is just wedged inbetween the
  66.     front case and the logic board. Remove both the switch contacts and the
  67.     plastic switch. (best know it now or loose them in the carpet)
  68.  
  69. 17. On the component side of the PC board you will see lots of nifty surface
  70.     mounted compone~ts, a fat little barrel capacitor (used for maintaining the
  71.     channel freqs while you change the batteries.. and make modifications :)
  72.     near the edge of the PC board you will see a couple of small diodes moutned
  73.     vertically. These will be labeled on the PC board as D10 and D11, you will
  74.     also see a place for another diaode to be soldered in but was not 
  75.     installed at the factory.. this is D9.
  76.  
  77. 18. You must now move diode D11 to the place where D9 is labled. As you have
  78.     probably noticed by now there is a tin cover over about 1/2rd of the
  79.     PC boards solder side. The edge of the tin cover nearest the diodes has
  80.     2 metal tabs soldered to the P board. Desolder these 2 tabs and gently
  81.     bend the metal cover way from the soder side of the PC board. This will
  82.     expose the board enough to let you get your soldering iron in to where
  83.     the diode leads are.
  84.  
  85. 19. Desolder the D11 diode from the bottom while pulling it away from the board
  86.     on the top  of the board using neadle nose pliers on the LEAD only.
  87.  
  88. 20. Now heat up the D9 solder pads and insert the diode (the same way it was 
  89.     oriented in the D11 location)
  90.  
  91. You Have Completed the Mods for complete 800mhz band coverage and 66-88mhz band
  92. coverage.
  93.  
  94.  
  95.  
  96. *******************************************************************
  97. Subject: Eliminating a birdie in the PRO-34 portable scanner
  98.            by Bob Parnass, AJ9S
  99.  
  100.    Birdies are unwanted signals generated within a receiver, which
  101.    cause the receiver to "hear itself."  Some birdies are caused by the
  102.    unwanted product of the local  oscillator.   Another  cause  is
  103.    a  stage, which oscillates but isn't meant to oscillate, such as a
  104.    high gain  intermediate frequency (IF) amplifier.
  105.  
  106.    Most birdies,  especially  those  generated  by  a  local
  107.    oscillator,  are frequency stable.  It's difficult to rid a radio of
  108.    these birdies, and solutions  usually  involve better internal
  109.    shielding and isolation among the stages.
  110.  
  111.    A "wandering birdie"  is  one  which  changes  frequency.  Wandering
  112.    birdies, and birdies which appear and disappear suddenly, may be
  113.    caused by  intermittent  ground  connections within the radio, or
  114.    defective bypass capacitors.
  115.  
  116.    After using his Radio ShackO PRO-34 portable scanner  for a  few
  117.    months, Ron Smithberg, a radio hobbyist in Joliet, was hampered by a
  118.    "wandering birdie."  Ron's scanner  was hearing  itself on a few
  119.    frequencies in the VHF-Hi range, but the birdie disappeared when he
  120.    tilted  the  radio  or squeezed  the  case.   There had been no
  121.    problem when the scanner was purchased initially.
  122.  
  123.    I suggested that a ground connection or a  circuit  board in  his
  124.    PRO-34  might be loose.  The thin PRO-34 plastic case feels chintzy,
  125.    and can flex easily by applying  just a  gentle  squeeze.  After
  126.    prolonged use, the case motion can loosen screws which were once
  127.    tight.
  128.  
  129.    Ron disassembled his PRO-34.  He unfastened  the  helical antenna,
  130.    knobs,  and  rear screws, then gingerly removed the plastic case.
  131.    After Ron tightened a Phillips screw holding  the  Logic  Board
  132.    to the front of the case, the birdie disappeared forever!
  133.  
  134.    The operation took a steady  hand.   Although  he  didn't have  to
  135.    remove any boards, Ron warned that accessing the offending screw was
  136.    a challenge.  He used  a  very  small Phillips  screwdriver,
  137.    positioned  through  a  hole in a shield partition.
  138.  
  139.  
  140.  
  141. *********************************************************** 
  142. Restoration of Cellular Frequency Coverage on
  143. Radio Shack PRO-34 Handheld Scanner
  144.  
  145. 1.  Remove battery cover and battery, four black screws on 
  146. rear cover, and volume and squelch knobs.
  147.  
  148. 2.  Remove rear cover, lifting back and up to clear controls.  Do not 
  149. remove belt clip or circuit board screws.
  150.  
  151. 3.  Unplug the brown volume control connector (grn/yel/blk) and white 
  152. squelch control connector (wht/blk/red) from the linear circuit board.
  153.  
  154. 4.  Unsolder the ground lead from T111 (at corner of linear circuit board 
  155. above the external power connectors).  Unsolder the two power switch leads 
  156. from the back of the volume control.  Unsolder the antenna connector center 
  157. pin and ground wires from the linear circuit board.
  158.  
  159. 5.  Unscrew the four combination screws that hold the linear circuit board and 
  160. received the back cover screws. Grasp the linear board at the top and lift it 
  161. straight away from the front case, unplugging the 16-pin connector.
  162.  
  163. 6.  Remove the three screws holding the metal frame assembly which held the 
  164. linear board to the front panel.  Unplug the red-black power lead and lay the 
  165. frame aside.  It is still connected to the battery contacts.
  166.  
  167. 7.  Locate diodes D9 - D12 on the volume control side of the of the logic 
  168. circuit board under T1; D10 and D11 are marked.  Clip one lead of D11, 
  169. separating the gap.  This may be resoldered later if desired.
  170.  
  171. 8.  Reassemble the board by reversing the disassembly procedures above.
  172.  
  173. pro34.14
  174.  
  175. Date: 4 Apr 89 14:24:01 GMT
  176. Subject: PRO-34 Scanner Modifications
  177.  
  178.     In  the  May 1989  edition  of  Popular  Communications  is a
  179. "Letter  to the Editor" on the Radio Shack PRO-34 Scanner.  Below
  180. is the text of that letter.
  181.  
  182.  
  183.                   PRO-34 Scanner Modification
  184.  
  185.     In regard to the information  presented (March Issue)  on the
  186. handheld Radio Shack PRO-34 scanner,  my own observations  on the
  187. modifications have been:
  188.  
  189. 1. To restore missing 800 MHz frequencies, remove D-11.
  190.  
  191. 2. To add 66 to 88 MHz  (European Coverage),  install a diode at
  192.    D-9.
  193.  
  194. 3. D-10 must remain in place for full 800 MHz coverage.
  195.  
  196. 4. If a diode is added at D-13 it cuts out aero band, also seems
  197.    to affect 800 MHz channel spacing.
  198.  
  199. 5. D-12 added dosen't seem to have any affect.
  200.  
  201. 6. Only D-10 and D-11 are factory installed.
  202.  
  203.