Phoenix Rising BBS

home *** CD-ROM | disk | FTP | other *** search

/ Phoenix Rising BBS / phoenixrising.zip / phoenixrising / misc / sanlock2.san < prev next >

Wrap

Text File | 1992-09-07 | 33KB | 827 lines

3/15/91 -------------------============< SANCTUARY >============------------------- | | | -----------==> Town Criers Posting Board <==----------- | | | | Just another EXCRETION from the bowels of Sanctuary... | |_____ City of _____| | |_____ Beggers, _____| | | The |_____ Criminals, _____| The | | Home |_____ and Thieves _____| Hellfire | | Board of |_____ _____| Bulletin Board | | Sanctuary |_____________| 1-908-495-3926 | |_________________________________________________________________________| ___________________________________________________________________________ -=> <=- -=> STUPID AND RETARDED DISCLAIMER!!!! <=- -=> <=- -=> I'm sure that you've seen TONS of these stupid and retarded <=- -=> disclaimers so pretend that you see one here.. Now read it <=- -=> CAREFULLY!!! Now make sure you understand what it says and <=- -=> understand its effects on your life.... (dum de de dum de) <=- -=> Finished?? Ok, hope you read it well.. Now let's get to it. <=- -=>_____________________________________________________________________<=- Introduction ------------ This is the second in a series of lockpicking philes put out from Sanctuary. The first, "An Introduction to Lockpicking" can be gotten from The Hellfire BBS if you missed it, as well as any other SANctuary phile that you might want. In this phile, we will cover parts 3, Disc Tumbler Locks, and 4, How to Mount Practice Locks, along with a few dos and don'ts thrown in. But starting off will be two lockpicking philes by The Ninja, Room Entry/ Lockpicking Techniques Parts I&II.. *************************************************************************** ** * * * The Ninja Warrior * * Presents: * * Room Entry/Lock Picking Techniques * * * *************************************************************************** ** THIS IS THE FIFTH OF THE NINJA009 SERIES. I HOPE YOU'VE ENJOYED THE FIRST FOUR BULLETINS AND I'M SURE YOU'LL ENJOY THIS ONE AS WELL... ***WARNING*** THERE IS A HEAVILY ENFORCED LAW ON BREAKING AND ENTRY. IF YOU GET CAUGHT FOR B&E, AND YOU ARE OVER 18, YOU WILL DEFINITELY GO TO * JAIL *... IF YOU ARE UNDER AGED...STILL DON'T DO IT, SOME TIMES THE STUFF YOU DO STAYS ON YOUR FUTURE RECORDS. BACKGROUND: ----------- NINJA'S WERE ABLE TO WALK THRU WALLS, ENTER AND LEAVE A ROOM WITHOUT A TRACE. THIS WAS ONE OF THE STEALTH SKILLS, THAT THE NINJA'S POSSESSED. THERE WERE RUMORS THAT NINJAS CAN VANISH INTO A WALL...WELL...THAT'S A LITTLE HOAX. YES WE ARE ABLE TO ENTER AND EXIT A ROOM WITHOUT A LARGE TRACE...IF YOU KNOW HOW JAPANESE HOUSES IN THE ANCIENT TIMES WERE BUILT, YOU CAN LOOK AT THE SUPPORT POSTS, THEY USUALLY HAVE GRAPPLING HOOK MARKS IF A NINJA HAD WALKED THRU THE ROOM TO KILL A PERSON OR SOMETHING. BUT ONE HAS TO LOOK VERY, VERY CAREFULLY. -------------- HOW TO DO ITS: -------------- WELL...I WON'T GET INTO ANY PHILOSOPHICAL BULLSHIT OR THE ANCIENT STUFF. I'LL GIVE YOU INFO ON THE STUFF YOU CAN PUT TO MODERN USE. HOW TO PICK FILE CABINET LOCKS: ------------------------------- IT'S QUITE SIMPLE TO PICK OPEN A FILE CABINET. MOST FILE CABINETS NOWADAYS HAVE A CHEAP DISK TUMBLING SYSTEM. IF THE DISK PATTERNS MATCH THE KEY SHAPE, PRESTO! IT'S OPEN. LET ME BRIEFLY EXPLAIN WHAT DISK TUMBLERS ARE... 80 I I I I I **** I I I ** * ****** * <----- KEY ************ * I I I I I **** ^ ^ ^ ^ ^ |--|--|--|--| EACH ONE OF THE THINGS THAT THE (^) ARROWS ARE POINTING TO ARE DISKS. ( SORRY FOR THE BAD ILLUSTRATIONS. ) IF THE KEY INSERTED THRU THE 5 DISKS, AND THE PATTERN OF THE DISKS MATCH, IT OPENS. SO TO MAKE A KEY THAT WORKS WITH MOST (ALL) CABINET LOCKS... GET A WIRE FAIRLY THICK, JUST THIS ENOUGH TO FIT THRU THE LOCKS. BEND IT IN THE FOLLOWING FASHION. +---- THE DISTANCE SHOULD EQUAL ----------/\/\/\- v FROM TOP OF THE DISTANCE /\ / THE HUMP TO ACROSS TWO ^ THE BOTTOM OF TOPS OR ^ ^ +------ THE HUMP BOTTOMS -----|--| WHEN YOU MAKE YOUR KEY, JUST INSERT IT ALL THE WAY IN. JERK IT UP AND DOWN AS FAST AS YOU CAN, AS YOU TURN THE KEY TO THE LEFT OR RIGHT, DEPENDING ON HOW THE LOCK OPENS. IF YOU GET THE HANG OF IT, YOU SHOULD BE ABLE TO OPEN ANY FILE CABINET LOCK IN A MATTER OF SECONDS. I USUALLY TAKE ABOUT 3 TO 5 SECONDS WITH MY KEY. OPENING LOCKED DOORS: --------------------- I CAN WRITE A WHOLE BOOK IN TEACHING HOW TO OPEN LOCKED DOORS. I'LL TELL YOU THE MOST BASIC WAY OF DOING IT. THIS TECHNIQUE HAS TO BE A DOOR WITH A GAP AS WIDE AS A WIDTH OF A BUTTER KNIFE. IF YOU HAVE A BUTTER KNIFE OR A BUTTER FLY KNIFE OR EQUIVALENT, HANDY, YOU CAN OPEN THESE KINDA DOORS AS THOUGH YOU HAVE THE KEY TO THEM. DOOR GAP | | | | |-| | |<---- THE SO CALLED "BOLT" OF THE DOOR. | | |-| | | | | | | BIRD'S EYE AND ENLARGED VIEW OF THIS |---------- THE KNIFE v I ----> SLIDE THE KNIFE THIS WAY FOR THIS PICTURE ____ I ______ |I _| |I/ | DOOR |/ | |___| ____| |_______ ^ |--------------- THE "BOLT" IF THE ROUND PART OF THE "BOLT" FACES YOU THEN WITH THE KNIFE, PUSH ON THE BOLT WITH THE BACK OF THE BLADE. AS YOU PUSH, SLIDE THE KNIFE TOWARDS THE SIDE OF THE DOOR. (SEE ILLUSTATION FOR CLARITY). YOU WILL SLOWLY MOVE IT. AND PRESTO! THE DOOR IS OPEN. THE TRICK IS TO SLIDE THE KNIFE AND PUSHING IT AT THE SAME TIME, AND HOLD ON TO THE DOOR KNOB. IF IT OPENS INWARDS, GET READY TO PUSH IT AS SOON AS THE KNIFE IS THRU THE "BOLT". FOR THE OTHER CASE ( THE ROUND PART OF THE "BOLT" FACING AWAY FROM YOU ), YOU JUST PULL ON THE KNIFE AND GIVE THE SAME SLIDING MOTION. BE CAREFUL NOT TO STAB YOURSELF. THE KNIFE'S CONTACT POINT IS ALWAYS THE BACK OF THE KNIFE. *************************************************************************** * * * * * * * The Ninja Warrior * * * * Presents: * * * Room Entry/Lock Picking Techniques Part II * * * * * * * *************************************************************************** THIS IS THE SIXTH OF THE NINJA009 SERIES. THIS IS A CONTINUATION OF THE FIFTH OF THE SERIES. THIS WILL BE THE LAST PART OF THE LOCK PICKING TECKNIQUES. ***WARNING*** THERE IS A HEAVILY ENFORCED LAW ON BREAKING AND ENTRY. IF YOU GET CAUGHT FOR B&E, AND YOU ARE OVER 18, YOU WILL DEFINITELY GO TO * JAIL *... IF YOU ARE UNDER AGED...STILL DON'T DO IT, SOME TIMES THE STUFF YOU DO STAYS ON YOUR FUTURE RECORDS. -------------- HOW TO DO ITS: -------------- HOW TO PICK 5 PIN CIRCULAR TUMBLER LOCKS: ----------------------------------------- THIS IS VERY HARD...IT TAKES A LOT OF PRACTICE TO CRACK OPEN THESE KINDS OF LOCKS. MOST BIKE LOCKS AND ARCADE COIN SLOT LOCKS HAVE THIS TYPE OF LOCK. LET ME BRIEFLY EXPLAIN WHAT 5 PIN CIRCULAR TUMBLERS ARE... BIRD'S EYE VIEW _________ ___ --=_________ / o \ |- ===) /o o\ |- ==) \_o_o_/ |- ===)________ | --=_________ | +--- THE PINS (NOT ALL FIVE CAN BE SHOWN) THE KEY IS A SMALL CIRCULAR TUBE LIKE KEY WITH A LITTLE NOTCH AT THE END OF THE KEY, WITH FIVE SMALL DITCHES IN THE TUBE. WHEN ALL THE PINS ARE ARRANGED SO THAT THE LOCK TURNS, PRESTO!!! SOME HAVE SEVEN PINS.... SO TO MAKE A KEY THAT WORKS WITH 5 PIN BIKE LOCKS AND ET. AL. MAKING THE KEY IS VERY HARD...YOU HAVE TO MAKE A KEY, EVERYTIME YOU USE IT, ONCE! THIS IS A BITCH. THE PARTS AREN'T THE EASIEST TO FIND EITHER. FIND 5 SPRING STEEL NEEDLES THICK ENOUGH FOR STRENGTH, BUT THIN ENOUGH TO FIT INTO THE SIDES OF THE LOCKS. GET A TUBE THAT FITS THE LOCK PERFECTLY. YOU CAN KEEP THE TUBE FOREVER. TAPE THE SPRING STEEL NEEDLES ONTO THE PIPE. LET THE SPRINGS STICK OUT ABOUT 5 mm OUT OF THE PIPE. BUT MAKE SURE NONE OF THE SPRINGS ARE LAYED OUT EVENLY. NOW, INSERT IT INTO THE LOCK. GIVE IT A RAPID IN AND OUT MOTION. GET A SURGICAL SPRING NEEDLE FROM YOUR BIOLOGY LABORATORY AND USE THAT TO ROTATE THE LOCK AS YOU JIGGLE IT IN AND OUT. I HAD A HELL OF A HARD TIME PICKING OPEN A KRYPTONITE LOCK. I LOST MY KEYS TO MY BIKE AND IT WAS LOCKED TO A POLE. IT TOOK ME ABOUT 20 MINUTES. I HAD SUCCESSFULLY OPENED ONLY 5 OF THESE TYPES OF LOCKS, ONE OF THEM BEING A SEVEN PIN. IT IS VERY FRUSTRATING AND HARD. BUT WORK ON IT. OPENING CAR DOOR TYPE 1: ------------------------ I CAN WRITE A WHOLE BOOK IN TEACHING HOW TO OPEN CAR DOORS. I'LL TELL YOU THE TWO BASIC WAYS OF DOING IT. THE FIRST TECHNIQUE IS THE FOLLOWING: A CAR WITH A LIPPED DOOR LOCK: ___ ( ) ----- DOOR LOCK | | ________| |___________ _ THESE DOORS ARE SO EASY TO PICK, IT TAKES A PRO ONLY ABOUT A SECOND TO OPEN IT. JUST GET A HANGER AND TAKE IT APART TO BE A SO CALLED STRAIGHT WIRE. BEND IT LIKE THE FOLLOWING. _________________________ ______ ( L ) L = LENGTH (ABOUT 1-1/2 INCHES) THE LOOP PART OF THE HOOK SHOULD BE JUST BIG ENOUGH TO GRAB THE LOCK. JUST STICK IT IN THRU THE SIDE OF THE WINDOW. AS YOU INSERT IT, BEND IT TOWARDS THE LOCK. IF THE GAP OF BETWEEN THE DOOR AND THE WINDOW IS TOO SMALL, THEN USE THE SECOND TECHNIQUE. AS YOU APPROACH THE LOCK AND GET A HOLD OF IT, MAKE SURE YOU HAVE A SNUG GRIP ON THE LOCK BY TUGGING ON IT ONCE AND PULL IT IN AN UPWARD MOTION, FAST. PRESTO!!! IT'S OPEN. THIS IS VERY EASY. JUST PRACTICE ON YOUR OWN CAR OR SOMETHING, IF YOU GET A CHANCE, PRACTICE IN A SAFE LOOKING PARKING LOTS, (METRO, OR PRIVATE LOTS.) AND YOU'LL GET THE HANG OF IT. OPENING CAR DOOR TYPE 2: ------------------------ THIS ISN'T THAT HARD EITHER ONCE YOU GET THE HANG OF IT. YOU HAVE TO GET: A METAL RULER ABOUT AN INCH IN WIDTH AND AT LEAST 2 FOOT IN LENGTH. CUT THE METAL NOTCH IN THE FOLLOWING FASHION. | | | | |_ | \ | \ | \ | / | __/ / | / | \_ | | | | |_______| DO IT ACCORDING TO THE HARDCOPY'S SCALE FOR THE CUTS OF NOTCHES. IT IS AS CLOSE TO MINES AS POSSIBLE. THEN INSERT THE STICK INTO THE SIDE OF THE DOOR. FEEL FOR A PIN INSIDE THE CAR DOOR. ONCE YOU FIND THE PIN, PUSH SLIGHTLY DOWN ON IT AND THE PULL UP FAST. BINGO! IT'S OPEN. THIS NEEDS MORE PRACTICE THAN THE OTHER METHOD BUT IT'S NOT THAT HARD. PRACTICE MAKES PERFECTION...SO PRACTICE HARD. I'LL WRITE SOME MORE LOCK PICKING SCHEMES IN THE FUTURE. WELL...HAVE FUN. WRITTEN BY: THE NINJA WARRIOR ANY QUESTIONS REGARDING THIS OR THE PREVIOUS SERIES, LEAVE E-MAIL TO: THE NINJA MORE TO COME IN THE FUTURE..... LOOK FORWARD TO IT.... PRACTICE WHAT YOU'VE LEARNED.... This is one of MANY Great MYSTERY Notes at: The Mystery Zone Following will be parts 3-4 of my own phile. ---------- - PART 3 - Disc Tumbler Locks ---------- To start off, a tumbler lock is any part of the lock that is directly moved by the key and also has an unlocking function. So, the tumbler in the lock we are about to discuss is a lot like a disk, with a small rectangular looking slot cut into....about the center. _____ _| |_____ | ____| <--- Spring Finger | _ | | | | | | | |<------------ Key Slot | | | | | |_| | (This is BASICALLY what one | | looks like. Only the edges |_ _| and corners are slightly more |____| rounded.) Figure 1: An individual disc tumbler The trick is that the position of the slot can be varied, depending where the maker wants to put the key slot. It can be up slightly, further down slightly, (there are set increments, but there is no REAL reason to discuss them) but the dimentions of the slot itself never change. Now imagine that you take 5 of these disks (approx. nickel sized) and thread them onto a typical disc-tumbler key. (The key looks like your normal, average house key, only smaller. Keys to outer screen doors arean example.) Make sure that the disk you are imagining, are resting in the absolute bottom of the "V" cut on your key. (You can do this, if you like, with 5 pieces of cardboard to help you understand the concept.) _________ | |__ | | | | /\|/\ | | | () \ | /\|/ | \|/\|/\ | \|/ | | | | \ | __|___|___|___|__|__/ |____________| | | | | |<------ Cardboard Disks (HEY! It ain't that easy drawing a key in text so give me a break ok??) Figure 2: Cardboard practice tumblers threaded onto key cuts. So you can see that the disks are all the same height. This is how it should be with the varied key slots through the cardboard to adjust to the different depths of the "V" cuts. The following is the plug shown in side view. __ | | | |________________________________ | | _ _ _ _ _ | | | | |0| | | |0| | | |0< ------------ Spring Hole | | | | | | | | | | | | | | ------------------------------------ <---- Key Way | | | | | | | | | | | | | | | | |_| |0| |_| |0| |_| < ---------- Slot | |_____________________________|__| | | |__| Figure 3: View of Disk Lock Plug. The slots in the plug hold the tumblers in place parallel to each other but allow each tumbler to move individualy. The disks protrude outward from the slots with a constant outward pressure being exerted upon the disk by little springs under the spring finger of each tumbler. Now look at a diagram of a disk cylinder. This is what the plug mentioned and shown above slides into. ____________ / \ / ___ \ / | | \ / / \ \ | / \ | | \ / | \ \ / / \ |___| / \ / \ ___________ / Figure 4: Cylinder front view. Notice the 2 grooves that are 180 degrees apart. When the plug is inserted, the disks coming out of the plug are lined up with these grooves. This is what holds the plug from turning thus releasing the lock. Once a correct "key" is found that will turn the mechinism inside the plug, the disk tumblers will slide down into the plug, then allowing the plug to turn within the cylinder, thus opening your neighbor's...er....your door... The trick is to get all the tumblers at their varied hights, lined up so that they will all go into the plug and not impeade rotation. So if you had a disk tumbler lock that was loaded with all #3 depth disks, and a key with all #3 height "V" cuts, all the disk would go into the plug and you would be able to open the lock. Unfortuanly, such simple designs are never found, otherwise a straight wire could open the lock. So the lockmakers make it so all of the disk are at different depths, making it that much harder to align all of the disks at the same time. Rememeber, even 1 protruding disk will keep the lock locked. Something to remember is that some locks have as many as 10 disks, while 5 are the most common, 6 and 7 disk tumbler locks are not too unusual. Another type of disc tumbler lock is one that has two independent banks of tumblers that are 180 degrees apart. They fairly normal when you see them through the keyway,but they are really different because they move independently. They do tend to look like a staircase in the keyway. The way to tell for sure is by using a feeler or straight pick. Begin to manipulate one side. If both sides then move, you know that you are dealing with the normal variety. But if only one side moves, not both, you know you are dealing with independent banks of disk tumblers. Most if not all disk tumbler locks have what is called a plug retainer. This keeps the plug from being taken out end-wise from the cylinder. They range from cams screwed in at the far end, to snap rings, to being welded together at the factory. The most common is a disc retainer. This is simply an extra disk added to the end of the plug that does not move when the key is used. Some locks have a small hole in the lock face that can be used to defeat the disk retainer when th elock is unlocked. By using a cylinder retainer shim tool (Figure 5) you can push the disk retainer into the plug and remove the plug from the cylinder. | | |__________________________ | / |------------------------/ | | (The slant on the end is usually more steep.) Figure 5: Cylinder Shim Tool Since most plugs have a "shoulder" on them that prevents someone from pushing them into the cylinder, they can not be accessed that way either. Where Are They? -------------- Here are some common applications for disc tumbler locks. Can be found Cannot be found ------------ --------------- showcase locks padlocks telephone dial locks exterior/interior passage lock office machines other high usage applications cash registers bathroom towel dispensors gas tank covers switch locks other low-security applications sidebar locks in cars (to be covered in another section) glove compartments Basic Appearance ---------------- Most of the disk tumbler keys look like your house key (pin tumbler lock) but are a little smaller, about 1/4 or an inch shorter. Picking ------- Okay, you've had alot of backround shit throw at you, now let's put it to work and try to pick some locks. I recommend maybe trying your own locks around the house if you have any. In part 4, I'll tell you all the stuff you'll need to get started on mounting some prctice locks if you choose to do so. Once you have found a lock to try, or have mounted a practice lock in wood and put it in a vise, get a tension wrench (Figure 6). Insert the tension wrench into the lock making sure that you don't block the keyway cause the raking tool in going in next (Figure 7). __ | | | | | | ___________________________________________| | | __________________________________________| | | |_ _| | | | | Figure 6: Tension Wrench | | /\ |_______________________________/ \ | \ |------------------------------------\ | | Figure 7: Diamond pick used for raking technique If you have a problem finding a clear place to insert the tension wrench into, look for a shallow slot at the top or the bottom of the lock and put the wrench there. This is where the key usually bottoms so that you can't insert the key into the lock too far. It is a good place to put the wrench but remember not to apply to much tension. __________ |//////////| |////////<----- Tumbler coming down from the top. |----------| | | | | | | |__________| |\\\\\\\\\\| |\\\\\\\\<----- Shallow slot. |----------| Figure 8: Keyway view of disc tumblers After you insert the tension wrench into the lock, apply a little turning pressure in the direction that the lock nomally turns in. Do this until the disk bind, or cause resistance. Now insert the rake into the lock under all of the tumblers. (Note: Some locks have no backing so be careful not to stick the pick into the space behind the tumblers.) Now, check to see if the rake moves smoothly in and out, touching all of the tumblers. If not, the rake may be too high. Grip is also a factor. Your best bet would be to hold the pick like a pencil, and let it pivot at the point where the fingers grab it. If this is not comfortable, try holding in a way that is better for you. Tension is just as important. Remember to apply CONSTANT tension, but not too little, or too much. This you will just have to determine mostly with practice. Too much tension prevents the tumblers from moving, while to little gets you just as far. So, to recap, sum up, whatever. Apply a light, constant turning tension with the wrench, hold the pick right, putting it under all of the tumblers. Now move the rake in and out in a scrubbing motion, being sure to contact all of the tumblers on each pass, in both directions, letting the pick pivot. If you are having trouble with the first method, here are some things you can try. Try varing the tension, but don't let off totally. Sometimes, when you ease tension while doing a stroke, the lock pops open. Remeber, too much tension can also cause your pick to bend instead of scrub, so unless you like spending money on new picks, go easy. Also, sometimes a figure eight motion works good. To try this, keep the wrist loose, and let your fingers move the pick. One last technique you could try would be the "ripping" technique. This is when you carefully insert the pick into the lock without touching any tumblers, and then ripping it out in one very fasy stroke. If you have opened the lock, CONGRATS! Do it again..and again..and again.. If not, make sure you are trying to turn the lock in the right direction. You can also check the key profile. If the key is fairly straight, with few deep "v" cuts, it is easier to open than a lock that has a key with deep "v" cuts (Figure 9). ___________ | |_ | |_ _ _ _ | |____ / \ / \ / \ _ | \___/ \__/ \__/ \__/ \_ <--- Harder | () \ | ____________________________/ | ____/ | _| | _| |___________| ___________ | |_ | |_ | |____ _ _ _ _ | () \___/ \___/ \___/ \___/ \_ <--- Easier | \ | _________________________/ | ____/ | _| | _| |___________| Figure 9: Two sample key profiles Now that you've picked a disc tumbler lock (hopefully), start to notice how common these locks are. And most if not all can be picked by the same type of raking technique. After time, you'll catch on to the tensino mystery and be able to open any disc tumbler lock. The reason they are so easy to open is because they are factory made. So, since they are off of an assembly line, they have a lot of play in them. So is it wrong for us to point out the lack of quality in today's locks by picking them? Well, maybe, but who gives a shit. ---------- - PART 4 - Practice Locks and Some Dos and Don'ts ---------- Now that you are a practicing thief, whoops..heheh. I meant locksmith, you will need lock to practice on. I suggest getting the following types of locks: 1. Disc Tumbler Lock 2. Rim or Mortise Pin Tumbler 3. Lever Tumbler 4. Warded Mortise 5. Warded Padlock Try to get fairly cheap ones because cheaper usually means easier to pick. You should be able to pick most up at a local store, except maybe the warded mortise lock in which case you may want to go to some second- hand store, chances are you'll get it cheaper there anyhow. What you basically want to do, is mount the lock into a piece of wood as you would mount it into a door. Then clamp the wood in a vise. Or you could make a sort of cabinet with all the locks in one place and mount the cabinet on you wall where you can practice. Either way is fine. Just make sure you have SOME PLACE to practice. A little hint is to put the mounted lock(s), if possible, in a place where you walk often. That way you can practice every time you walk by or atleast you won't totally forget to practice a little. Remeber to practice alot on the pin tumblers once you know how to pick them (in next phile) because they are the most common. Also, don't forget that when you are picking to sometimes practice with a flashlight because when you are out in the "field", the owner of the house will most likely not be there holding a flashlight for you. Try holding the flashlight in your mouth or even taping it to your arm. If you want, you can also try velcro. Two fifteen minute practice sessions a day should get you well on your way. If you have looked in catalogs for lockpicks, I'm sure you have seen those "all in one" types. Where you get 8 picks inside a pen or something. Well, take a little advice and DO NOT buy one of these. Why? Simple. When you are lockpicking, you will often need to change the type of pick you are using. So if you need two hands to unscrew the old pick, and put on a new one, whixh hand is holding the tension wrench? None. So you lose tension and have to start all over again. Gee, isn't that fun. I would suggest buying one of those leather case tools. They may be more expensive, but they are worth it. Not to mention, the companies that make those "pen picks" seem to enjoy giving us 8 picks with 5 of them being of a type you will never use in YOUR lifetime. So stick to the kits that come in cases. These are generally better quality and easier to access cause you can just drape an open case across your knee when picking. Let's just go over the basic things to do when attempting to gain entry. First, make sure of the simple things. Like making sure the door, as well as windows and such are ACTUALLY locked. Also make sure that the door is not jammed. Check the lock also. If the lock is old and worn and requires manipulation when using the right key, do you think that you are going to be able to PICK it open. Probably not. Next, figure out what type of lock it is. A stamped metal plate with a keyway cut into it is usually a warded lock, or a lever tumbler lock (lever tumblers will be in the next phile.) The circulaer shaped locks, like the ones on the door to your house, are usually pin tumbler, disc tumbler, or wafer tumbler locks (Schlage). On padlocks especially, if the core rotates, this could mean a warded lock. It is a lever tumbler lock if the rotating core has a slot cut in the side of it's retainer. If the core doesn't move, it is a pin tumbler. | | |_________________________________ |_____________________________ / | | / | |/ | Figure 10: Broken key extractor. Next, check the keyway for foreign objects. A little trick some burglers use is to put broken toothpicks in the key way. This slows down a homeowner who could surprise an unalert burgler. Also, make sure that you can see the tumblers. If not, they could be jammed up inside the cylinder. Something else that you may sometimes notice is that there are very few tumblers. This is because some shity locksmith put in only a few tumblers, this making the lock easier to pick. Also, make sure you know what type of lock it is. It may not be what you think. Also, check for a brand name if visable. Certain brands like, CORBIN or RUSSWIN use or have installed slightly different parts making the lock a little harded to pick, sometimes (i.e. mushroom pins) Next, insert the tension wrench into the plug and try to ratate it. The more it rotates, the more play is in the lock, meaning it's easier to pick. While you are doing this, try to figure out which way the plug turns. This is VERY important. If you apply tension in the wrong direction whiel picking a lock, you will never open it. You can tell the difference by the way the plug stops. If you feel an abrupt, solid stop, that is the WRONG way. If you feel a slow increase in friction to a stop, that is usually the way to turn it. Cleaning the lock is also very important. Well, not VERY important, but it is good to know. A hint if the lock is in bad condidtion is if you smell some kind of lubricant. Chancea are that the lock is not in godd shape and the owner tried to get it to work better by shooting some WD-40 into it, which by the way is bad for locks cause it leaves a residue. Use lighter fluid to clean a lock. Gasoline and LPS-1 are also BAD to use cause of the residue left after evaporation. WARNING: Cleaning the lock with lighter fluid or naptha (another cleaning agent) leaves a smell. This will be left behind after you have gone for the homeowner or whomever to smell and shows that someone was fideling with the lock. Flush clean twice, using a straight tool to work the tumblers betwwen each washing. Then blow dry. You could try those gases in a can from cetain chemical supply house also to blow the lock dry. The purpose is to float away any dirt when cleaning and drying the lock. Now that the lock is clean, if it wasn't already you are ready to pick it. Some people like lubricant in a lock, other don't. It is your choice, but if you do, a short squirt of powdered graphite is you best bet to use. Also remeber to look under flower pots, rocks, etc for keys before attempting to open a lock. Just think where you might hide something, and look there. Try to get into the routine of surveying the lock in the ways just described. If you get in a habit of it, you may not overlook something obvious when it happens. It will also help you in general to open locks. Well, that's it for my second phile on lockpicking. In the next lockpicking phile, look for articles on: Lever Tumbler locks & Pin Tumbler Locks. So until then, happy trails, and remeber not to get the foreskin caught in the zipper. ------------------============<HELLFIRE BBS!!!>===========----------------- Sanctuary WORLD HQ!!! (908) 495-3926 Greets to THG,INC,NEUA, Hey PE...where's the wares??? Look foward to many more Great P/H/C Docs from SANctuary!!! Remember, SANctuary is ALWAYS looking foe new writers, courriers, dst. sites and possibly even members! If you would like to be any of these Leave Me or Havok Halcyon e-mail at HELLFIRE, or write to: Sanctuary Po Box 286 Keansburg, NJ 07734 ----===Red===---- This phile written by Havok Halcyon. Downloaded From P-80 Systems 304-744-2253