home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
Current Shareware 1994 January
/
SHAR194.ISO
/
modem
/
clcom201.zip
/
CLICKCOM.XXX
/
MODEMS.SCM
< prev
next >
Wrap
Text File
|
1993-04-05
|
51KB
|
2,589 lines
@Anchor 2400i Internal - Half-card
2400
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,CTS
ATS0=0H0
^ATE1Q0M1X4V1S7=60
^AT&C1&D2&W
*Your 2400 baud modem is now initialized and ready to go!
@AST 2X9600
19200
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,CTS
ATS0=0H0
$ Switch Settings: FRONT 1 2 3 4 5 6 7 8 9 10
$ U D D U D U U D * *
$
$ REAR 1 2 3 4 5 6 7 8
$ *=Not Used D D D U D U U *
^AT&F
^AT&C1&D2\J0\N3\Q3\V1&W
*Your AX9624c is now configured for 19200 baud operation. Be sure
*to setup ALL your dialing directory entries for 19200 operation to
*get the best speed on all calls.
@AT&T Dataphone II 2212C - 1200 baud
1200
A^~T^~^M^~^~^M
^M^~^~ATT
Answered
Not connected
Invalid number
No dial
Busy
$ Switch e: INSIDE 1 2 3 4
$ C O O O
$ C=closed O=open
$
$ These are inside the case.
^M^~^~od^~^~^~y^~^~^~at^M^~^~^~^M^~^~^M
*Your Dataphone II is ready to go! Be sure to read your modem
*manual and double-check the setup.
@AT&T Model 4000
1200
ATV1E1Q0X2S7=45S0=0
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
XON
ATS0=0H0
*Your AT&T modem is now configured for best performance with
*Click Comm.
*
*An option might be to add M0 to the modem initial string to
*silence your modem if you prefer.
@ATI 2400etc - non V.42
9600
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,CTS
ATS0=0H0
^AT&F1
^AT&C1&D2&W
*Your ATI 2400etc modem is ready to go! You can set all of your
*dialing directory entries to 9600 and the modem will handle
*speed conversions for you. MNP operation has been enabled.
@ATI 2400etc/e & 2400etc/i - with V.42
9600
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON
ATS0=0H0
^AT&F2
^AT&C1&D2&W
*Your ATI 2400etc modem is ready to go! You can set all of your
*dialing directory entries to 9600 bps and the modem will handle
*speed conversions for you. MNP operation has been enabled.
@ATI 9600etc/e V.32/V.42
38400
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON
ATS0=0H0
^AT&F2
^AT&C1&D2&W
*Your ATI 9600etc modem is configured and ready to go! You can
*set all of your dialing directory entries to 38400 bps and the
*modem will handle speed conversions for you.
@Avatech 2400E
2400
ATE1Q0V1X4&C1&D2S7=55S11=60S0=0
ATDT
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
XON
ATS0=0H0
*Your Avatech modem is now configured for best performance
*with Click Comm.
*
*An option might be to add M0 to the modem initial string to
*silence your modem if you prefer.
@BSM Quick Comm 2400 MNP
9600
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
CTS
ATS0=0H0
^AT&FV1Q0
^AT\Q3\J0\N3%C1&C1&D2S7=55S0=0
^AT&W
*Your BSM modem is now set up for best perfomance with Click
*Comm. Compression is enabled, so set ALL of your dialing
*directory entries to 9600 bps for best performance.
@Businessland Ext. 2400 Error Correcting
9600
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
ATS0=0H0
$ Switch Settings: SW2: 1 2 3 4 5 6 7 8 9 10
$ D D U D U D U U U D
$
$ SW3: 1 2 3 4
$ D D D D
^AT&F&W
^AT&C1&D2\N3\C1\Q3\V1X4M3\J1\D1\G1&W
*Your Businessland modem is now set up for best perfomance
*with Click Comm. Compression is enabled, so set ALL of
*your dialing directory entries to 9600 bps for best performance.
@Cardinal 2400 MNP
9600
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,CTS
ATS0=0H0
^AT&F
^AT&C1&D2&T5\C1\J0\N3\Q3\V1\K3&W
*Your Cardinal 2400 MNP modem is configured and ready to go! You
*can set your dialing directory entries to 9600 bps and your modem
*will handle speed conversions for you. MNP operation has been
*enabled.
@Cardinal 2400 non-MNP
2400
ATZV1Q0&C1&D2S11=60S7=60S0=0
ATDT
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
XON
ATS0=0H0
*Your Cardinal modem is now set up for best perfomance with
*Click Comm.
@Cermetek INFO-MATE 212A
1200
U 1^M~C 0^M
D 'T
A
B
X
N
V
DTR,XON
$Open the case to set these switches. Refer to your manual for
$this procedure.
$
$Switch settings: 1 2 3 4 5 6 7 8
$ ON OFF OFF ON ON OFF ON OFF
$
*Your Info-Mate 212A is configured and ready to go! Be sure to
*read your manual and double-check the setup.
@Cermetek 1200 SPC
1200
AT E1 Q0 V1 X2 S7=55 S11=60 S0=0^M
ATDT
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
NO ANSWER
XON
ATS0=0H0
$ Switch Setup: 1 2 3 4 5 6 7 8
$ U D D U U D U D
*Your Cermetek modem is now configured for best performance
*with Click Comm.
*
*An option might be to add M0 to the modem initial string to
*silence your modem if you prefer.
@Cermetek R/2400 SPC
2400
AT E1 Q0 V1 X4 S7=55 S11=60 S0=0^M
ATDT
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
NO ANSWER
XON
ATS0=0H0
$ Switch Setup: 1 2 3 4 5 6 7 8
$ U D D U U D U D
*Your Cermetek modem is now configured for best performance
*with Click Comm.
*
*An option might be to add M0 to the modem initial string to
*silence your modem if you prefer.
@Codex 2264
19200
ATZ
ATDT
CONNECT
NO DIALTONE
NO CARRIER
BUSY
NO ANSWER
DTR,CTS
ATS0=0H0
^AT&FV1Q0
^AT&C1&D2*FL3*XC1*PT0&R0
^AT&W
*Your Codex modem is now configured for best performance with
*Click Comm. Compression is enabled, so set ALL of your dialing
*directory entries to 19200 bps for best performance.
*
*An option might be to add M0 to the modem initial string to
*silence your modem if you prefer.
@CompuCom Speedmodem
19200
AT&F2*H2&D2S10=30%C0H0
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
NO ANSWER
DTR,XON,CTS
ATS0=0H0
*Your SpeedModem is configured and ready to go! You can set all
*of your dialing directory entries to 19200 bps and the modem will
*handle speed conversions for you.
@CTS Companion 212AH
1200
ATE1Q0V1S7=55S11=60S0=0
ATDT
CONNECT
Disconnect
NO CARRIER
BUSY
NO ANSWER
XON
ATS0=0H0
*Your CTS modem is now configured for best performance with
*Click Comm.
*
*An option might be to add M0 to the modem initial string to
*silence your modem if you prefer.
@CTS Datacomm 2424ADH
2400
ATZ
ATDT
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
NO ANSWER
XON
ATS0=0H0
^AT&FV1Q0
^AT^C1&D2S0=0S2=255S10=30X4
^AT&W
*Your CTS modem is now configured for best performance with
*Click Comm.
*
*An option might be to add M0 to the modem initial string to
*silence your modem if you prefer.
@Delta Gold DM 1200
1200
ATE1Q0V1X4 S7=55 S11=60 S0=0^M
ATDT
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
NO ANSWER
XON
ATS0=0H0
*Your Delta modem is now configured for best performance with
*Click Comm.
*
*An option might be to add M0 to the modem initial string to
*silence your modem if you prefer.
@Digicom 9624LE / 9624PC V.32bis
38400
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,CTS
ATS0=0H0
^AT&F
^AT*F3*E9&W
*Your Digicom modem is configured and ready to go! You can set
*all of your dialing directory entries to 38400 bps and the modem
*will handle speed conversions for you.
@Digitan Hi*IQ ZX1896 2400 Fax Modem
2400
ATE1Q0V1X4&C1&D2S7=60S25=4
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,CTS,XON
ATS0=0H0
*Your 2400 baud modem is configured and ready to go! Be sure to
*read your manual and double-check the setup.
@E*Tech Bullet PC2400MH MNP
9600
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,CTS
ATS0=0H0
^AT&F
^AT&C1&D2&T5$C1$E2$F4$X1&W
*Your E*Tech 2400 MNP modem is configured and ready to go! You
*can set your dialing directory entries to 9600 bps and the modem
*will handle speed conversions for you.
@E*Tech Bullet E9696M V.32 MNP
19200
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON
ATS0=0H0
^AT&F
^AT&C1&D2&T5$C1$E1$F4$S0$X5&W
*Your E*Tech 9696M modem is configured and ready to go! You can
* set all of your dialing directory entries to 19200 bps and the
*modem will handle speed conversions for you.
@Everex 12e External (EV-936)
1200
ATE1F1H0M1Q0V1X4&C1&D2
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
NO ANSWER
DTR,CTS,XON
ATS0=0H0
$ Switch Setup: 1 2 3 4 5 6 7 8 9
$ On Off Off Off Off On Off Off Off
*Your Everex 12e (EV-936) is configured and ready to go! Be sure
*to read your manual and double-check the setup.
@Everex 24e External (EV-945)
2400
ATE1F1H0M1Q0V1X4&C1&D2
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
NO ANSWER
DTR,CTS,XON
ATS0=0H0
$ Switch Settings: 1 2 3 4 5 6 7 8 9
$ On Off Off Off Off On Off Off Off
*Your Everex 24e (EV-945) is configured and ready to go! Be sure
*to read your manual and double-check the setup.
@Everex Evercom 24+ MNP
9600
AT\C0\J0\K5\N3\Q0\V1V1E1Q0X4
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
NO ANSWER
DTR,XON,CTS
ATS0=0H0
*Your Everex Evercom 24+ is configured and ready to go! Be sure
*to read your manual and double-check the setup.
@Everex EverFax 24/96
9600
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
NO ANSWER
DTR,XON,CTS
ATS0=0H0
^AT&F
^AT&T5\J0\N3\V1\X1%C1\Q3&W
*Your Everex EverFax 24/96 is configured and ready to go! Be
*sure to read your manual and double-check the setup.
@Fastcomm FDX 2424 (MNP Class-5)
9600
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
NO ANSWER
DTR,XON,CTS
ATS0=0H0
$All switches on the bottom of the modem should be in the
$OPEN (off) position.
^AT&F
^ATE1Q0M1X4V1S7=60
^AT&B1&C1&D2&G0&H1&I1&M6&W
*Your FDX 2424 modem is configured and ready to go! Be sure to
*read your manual and double-check the setup.
@Fastcomm FDX 2496
9600
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
NO ANSWER
DTR,XON
ATS0=0H0
$All switches on the bottom of the modem should be in the
$OPEN (off) position.
^AT&F
^ATE1Q0M1X4V1S7=60
^AT&B1&C1&D2&G0&H1&I1&M6&W
*Your FDX 2496 modem is configured and ready to go! Be sure to
*read your manual and double-check the setup.
@Fastcomm FDX 9696 (V.32 & MNP-5)
19200
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
NO ANSWER
DTR,XON,CTS
ATS0=0H0
$All switches on the bottom of the modem should be in the
$OPEN (off) position.
^AT&F
^ATE1Q0M1X4V1S7=60
^AT&B1&C1&D2&G0&H1&I1&M6&W
*Your FDX 9696 modem is configured and ready to go! Be sure to
*read your manual and double-check the setup.
@Forval IM14400/SA14400 V.32bis (38400 bps)
38400
ATZ0
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,CTS
ATS0=0H0
^AT&F
^ATS25=0S7=60%E0\J0\Q3&W
*Your Forval modem is configured and ready to go! You can set
*all of your dialing directory entries to 38400 bps and the
*modem will handle speed conversions for you.
@Generic 1200 bps Hayes clone
1200
ATE1Q0M1X1V1
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^~^~^~+++^~^~^~ATH0
ATS0=0H0
$If your modem hardware has switches or jumpers, be sure to set
$the modem so that it DOES NOT force Carrier Detect (this is
$usually switch No.6). Set the DTR so that is NOT forced on
$all the time (this is usually switch No.1). If your modem uses
$NRAM to store the configuration, Use the Generic
$1200 bps (No Switch) after this.
*Your 1200 bps modem is configured and ready to go! Be sure to
*read your modem and double-check the setup.
@Generic 1200 bps Hayes clone (No Switch)
1200
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,CTS,XON
ATS0=0H0
^ATE1Q0M1X1V1S7=60
^AT&C1&D2&W
*Your 1200 bps modem is configured and ready to go! Be sure to
*read your modem and double-check the setup.
@Generic 2400 bps Hayes clone
2400
ATE1Q0M1X1V1
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^~^~^~+++^~^~^~ATH0
ATS0=0H0
$If your modem hardware has switches or jumpers, be sure to set
$the modem so that it does NOT force Carrier Detect (this is
$usually switch No.6). Set the DTR so that is NOT forced on
$all the time (this is usually switch No.1). If your modem uses
$NRAM to store the configuration, Use the Generic 2400
*(No Switch) after this.
*Your 2400 bps modem is configured and ready to go! Be sure to
*read your manual and double-check the setup.
@Generic 2400 bps Hayes clone (No Switch)
2400
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,CTS
ATS0=0H0
^ATE1Q0M1X1V1S7=60
^AT&C1&D2&W
*Your 2400 bps modem is configured and ready to go! Be sure to
*read your manual and double-check the setup.
@GVC 2400 MNP-5
4800
ATZ~~~&C1&D2%C1\Q3\J0\N3\V1
ATDT
CONNECT
NO DIALTONE
NO CARRIER
BUSY
NO ANSWER
DTR,XON,CTS
ATS0=0H0
^AT&FV1Q0
^AT&C1&D2%C1\Q3\J0\N3\V1
^AT&W
*Your GVC modem is now configured for best performance with
*Click Comm. Compression is enabled, so set ALL of your
*dialing directory entries to 4800 bps for best performance.
*
*An option might be to add M0 to the modem initial string to
*silence your modem if you prefer.
@GVC 9600 V.42
19200
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,CTS
ATS0=0H0
^AT&F
^AT&C1&D2\Q3\J0\V1&W
*Your GVC 9600 modem is configured and ready to go! You can set
*all of your dialing directory entries to 19200 bps and the modem
*will handle speed conversions for you.
@GVC SM96 V.42bis
38400
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON
ATS0=0H0
^AT&F2&W
*Your GVC modem is configured and ready to go! You can set all
*of your dialing directory entries to 38400 bps and the modem
*will handle speed conversions for you.
@Hayes Personal Modem 1200
1200
AT E1 Q0 V1 X4 &C1 &D2 S0=0
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,CTS,XON
ATS0=0H0
*Your Hayes modem is now configured for best performance with
*Click Comm.
*
*An option might be to add M0 to the modem initial string to
*silence your modem if you prefer.
@Hayes SmartModem 1200 External
1200
ATE1Q0M1X1V1S7=60
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^~^~^~+++^~^~^~ATH0
ATS0=0H0
$ Switches: 1 2 3 4 5 6 7 8 9 10
$ U U D U D U U D U U
$
$ Note: Earlier versions did not have switches 9 & 10.
*Your Hayes Smartmodem is configured and ready to go!
@Hayes SmartModem 1200B Full Card Internal
1200
ATE1Q0M1X1V1S7=60
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^~^~^~+++^~^~^~ATH0
ATS0=0H0
$ Hayes has changed this version of the modem several times.
$ Plese be aware that your modem may or may not have all of these
$ switches or that these are the correct settings. Check
$ your manual to know for sure...
$
$ Switches: #2 DOWN - RJ12/RJ13 phone jack
$ UP - RJ11 or equivelent
$ #3 UP - Allow true CD
$ #4 UP - Allow DTR
$ (earlier versions required strapping
$ pins A-B for this function)
*Your SmartModem 1200B is configured and ready to go!
@Hayes SmartModem 1200B Half Card Internal
1200
ATE1Q0M1X1V1S7=60
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^~^~^~+++^~^~^~ATH0
ATS0=0H0
$ Switches: #2 RIGHT - RJ12/RJ13 phone jack
$ LEFT - RJ11 or equivelent
$ #3 RIGHT - Allow true CD
$ #4 LEFT - Allow DTR
*Your SmartModem 1200B is configured and ready to go!
@Hayes SmartModem 2400
2400
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,CTS,XON
ATS0=0H0
^ATE1Q0M1X4V1S11=60
^AT&C1&D2&W
*Your Smartmodem is configured and ready to go!
@Hayes V-Series 2400 (without V.42)
2400
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON
ATS0=0H0
^ATE1Q0M1X4V1S11=60
^AT&C1&D2&G0&J0&K3&L0&P0
^AT&Q5&W
*Your V-Series Smartmodem is configured and ready to go!
@Hayes V-Series 2400 (with V.42)
4800
ATZ0AT&Q5S36=3
ATDT
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
CTS
ATS0=0H0
^AT&FV1Q0
^AT &C1 &D2 &K3 S7=55 S11=60
^AT&W0
*Your Hayes modem is now set up for best perfomance with Click
*Comm. Compression is enabled, so set ALL of your dialing
*directory entries to 4800 bps for best performance.
@Hayes Personal Modem 2400
2400
AT&C1&D2E1Q0
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^~^~^~+++^~^~^~ATH0
ATS0=0H0
*Your Hayes Personal modem is configured and ready to go! Be
*sure to read your manual and double-check the setup.
@Hayes V-Series 9600
19200
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,CTS
ATS0=0H0
^ATE1Q0M1X4V1S11=60
^AT&C1&D2&G0&J0&K3&L0&P0
^AT&Q5&W
*Your V-Series Smartmodem is configured and ready to go!
@Hayes V-Series 9600 V.42
19200
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,CTS
ATS0=0H0
^ATE1Q0M1X4V1S11=60
^AT&C1&D2&G0&J0&K3&L0&P0
^AT&Q5S36=7S46=2S48=7W2&W
*Your V-Series SmartModem with V.42 is ready to go!
@Hayes V-series ULTRA Smartmodem 9600
38400
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,CTS
ATS0=0H0
^AT&F
^ATE1N1Q0M1X4V1W2
^AT&C1&D2&G0&J0&K3&L0&P0
^AT&Q5&U0
^ATS7=60S49=8S50=240&W
*Your V-Series ULTRA is configured and ready to go!
@IBM Model 5841 (1200)
1200
ATE1Q0V1S7=55S11=60S0=0^M
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
XON
ATS0=0H0
*Your IBM modem is now configured for best performance with
*Click Comm.
*
*An option might be to add M0 to the modem initial string to
*silence your modem if you prefer.
@IBM PC 2400
2400
ATE1Q0V1X4&C1&D2 S7=55 S11=60 S0=0
ATDT
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
XON
ATS0=0H0
*Your IBM modem is now configured for best performance with
*Click Comm.
*
*An option might be to add M0 to the modem initial string to
*silence your modem if you prefer.
@IBM PCjr Internal
300
^NF 4
ATDT
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
XON
ATS0=0H0
*Your IBM modem is now configured for best performance with
*Click Comm.
*
*An option might be to add M0 to the modem initial string to
*silence your modem if you prefer.
@Incomm 2400EC
2400
ATE1V1Q0&C1&D2\K3\N3\Q3\H0S11=60S7=55
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
XON
ATS0=0H0
*Your Incomm modem is now configured for best performance
*with Click Comm.
*
*An option might be to add M0 to the modem initial string to
*silence your modem if you prefer.
@Infomate 212/A PC
1200
ATE1V1Q0 S7=55 S11=60 S0=0
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
ATS0=0H0
*Your Infomate modem is now configured for best performance
*with Click Comm.
*
*An option might be to add M0 to the modem initial string to
*silence your modem if you prefer.
@Infomate 212/X PC
1200
ATE1Q0V1 S7=55 S11=60 S0=0
ATDT
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
ATS0=0H0
*Your Infomate modem is now configured for best performance
*with Click Comm.
*
*An option might be to add M0 to the modem initial string to
*silence your modem if you prefer.
@Intel 2400EX MNP
9600
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,CTS
ATS0=0H0
^AT&F
^AT&T5\J0\N3\Q3\V1\X1&W
*Your Intel 2400EX modem is configured and ready to go! You can
*set all of your dialing directory entries to 9600 bps and the
*modem will handle speed conversions for you.
@Intel 9600EX V.32 with V.42bis
38400
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,CTS
CTS
ATS0=0H0
^ATZ
^AT&FV1Q0
^AT \Q3\N3\J0\V1\C0S11=60
^AT&W
*Your Intel 9600EX modem is configured and ready to go! You can
*set all of your dialing directory entries to 38400 bps and the
*modem will handle speed conversions for you.
@Intel SatisFAXion
4800
ATZ0^M
ATDT
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
CTS
ATS0=0H0
^AT&F
^AT \C1 S11=60
^AT&W0
*Your Intel modem/fax is now set up for best perfomance with
*Click Comm. Compression is enabled, so set ALL of your
*dialing directory entries to 4800 bps for best performance.
@Maxwell Modem 300/V
300
AT E1 Q0 V1 S0=0^M
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
XON
ATS0=0H0
*Your Maxwell modem is now configured for best performance
*With Click Comm.
*
*An option might be to add M0 to the modem initial string to
*silence your modem if you prefer.
@Maxwell Modem 1200VP
1200
AT E1 Q0 V1 X4 &C1 &D2 S7=55 S0=0
ATDT
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
XON
ATS0=0H0
*Your Maxwell modem is now configured for best performance
*With Click Comm.
*
*An option might be to add M0 to the modem initial string to
*silence your modem if you prefer.
@Maxwell Modem 2400PC
2400
AT E1 Q0 V1 S7=30 S0=0
ATDT
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
XON
ATS0=0H0
*Your Maxwell modem is now configured for best performance
*With Click Comm.
*
*An option might be to add M0 to the modem initial string to
*silence your modem if you prefer.
@Microcom AX/1200,AX/2400 (wo/compression)
9600
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,CTS,MICROCOM
ATS0=0H0
$ Switches: FRONT 1 2 3 4 5 6 7 8
$ U D D U D U U D
$
$ REAR 1 2 3 4 5 6 7 8
$ D U D U D U D U
^AT&C1&D2&T5\N3\J0\Q3&W
*Your modem is now configured for operation. Be sure
*to set all your dialing directory entries to 9600 bps to get the
*best speed on all calls.
@Microcom AX/1200c,AX/2400c (w/compression)
9600
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,CTS,MICROCOM
ATS0=0H0
$ Switches: FRONT 1 2 3 4 5 6 7 8
$ U D D U D U U D
$
$ REAR 1 2 3 4 5 6 7 8
$ D U D U D U D U
^AT&F
^AT&C1&D2&T5\N3\J0\Q3&W
*Your modem is now configured and ready for operation. Be sure
*to set all your dialing directory entries to 9600 bps to get the
*best speed on all calls.
@Microcom AX/9624c AX/9612c
19200
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,CTS,MICROCOM
ATS0=0H0
$ Switches: FRONT 1 2 3 4 5 6 7 8 9 10
$ U D D D D U U D U U
$
$ REAR 1 2 3 4 5 6 7 8
$ D D D U D U D D
^AT&F
^AT&C1&D2&T5\N3\J0\Q3&W
*Your AX9624c is now configured and ready for 19200 bps
*operation. Be sure to set all your dialing directory entries to
*19200 bps to get the best speed on all calls.
@Microcom QX/V.32c
38400
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,CTS,MICROCOM
ATS0=0H0
$ Switches: FRONT 1 2 3 4 5 6 7 8 9 10
$ U D D U D U U D U
$
$ REAR 1 2 3 4 5 6 7 8
$ D U D U D D D D
^AT&F
^ATX4\V1\N3\J0\Q3
^AT&D2&C1&T5%C3&W
*Your QX/V.32c is now configured and ready for 38400 operation.
*Be sure to set all your dialing directory entries to 38400 bps
*to get the best speed on all calls.
@Microcom QX/4232hs
38400
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,CTS,MICROCOM
ATS0=0H0
$ Switches: FRONT 1 2 3 4 5 6 7 8 9 10
$ U D U U U D D D U
$
$ REAR 1 2 3 4 5 6 7 8
$ D U D U D U U D
$
$ T/D in Data Mode
$ O/A your choice.
^AT&F
^ATE1Q0X4\V2\N5\J0\Q3
^AT&D2&C1&T5%C3&W
*Your QX/4232hs is now configured and ready for 38400 operation.
*Be sure to set all your dialing directory entries to 38400 bps
*to get the best speed on all calls.
@MHz EasyTalk 1200
1200
AT E1 Q0 V1 S7=55 S11=60 S0=0
ATDT
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
ATS0=0H0
*Your Megahertz modem is now configured for best performance
*with Click Comm.
*
*An option might be to add M0 to the modem initial string to
*silence your modem if you prefer.
@MHz EasyTalk 2400
2400
AT E1Q0V1X4&C1&D2S7=55S11=60S0=0
ATDT
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
ATS0=0H0
*Your Megahertz modem is now configured for best performance
*with Click Comm.
*
*An option might be to add M0 to the modem initial string to
*silence your modem if you prefer.
@Multi-Tech MultiModem 224PC5
2400
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON
ATS0=0H0
$Switch Set up on the Bottom of the modem:
$ Bank 1 OPEN
$ 2 *
$ 3 * *=Sets COM Port
$ 4 CLOSED
^AT&F
*Your 224PC5 is now configured and ready for 2400 bps operation.
*Be sure to read your manual and doublecheck the setup.
@Multi-Tech MultiModem 224EC / 224PC W/MNP
9600
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON
ATS0=0H0
$Switch Set up on the Bottom of the modem:
$ Bank 1 OPEN
$ 2 *
$ 3 * *=Sets COM Port
$
$ 224EC: Switches on Back of Edgecard
$ 1 OPEN (Up)
$ 2 OPEN (Up)
$ 3 CLOSED (Down)
$ 4 CLOSED (Down)
^AT&F
^AT&E1&E4&E15
^AT$MB2400$SB9600$BA0&W0
*Your 224EC/224PC is now configured and ready for 9600 bps
*operation. Be sure to set all your dialing directory entries to
*9600 bps to get the best speed on all calls.
@Multi-Tech MultiModem MT224EH5 (MNP 5)
9600
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,CTS
ATS0=0H0
$Switch Set up on the Bottom of the modem:
$ 4 Bank 1 2 3 4
$ D U D D
$ 8 Bank 1 2 3 4 5 6 7 8
$ U U D U D U U D
$
$Jumpers to be changed -inside- the modem:
$ RTS: toward the back of the modem.
$ CTS/RTS: toward the back of the modem.
^AT$A0&B0&BS0&C1$D0&D2$F1
^AT&G0$MI0&M0$R1&R1&S1
^ATB1E1M1Q0V1X4&Q0
^AT&E1&E4&E8&E10&E13&E15
^AT$MB2400$SB9600$BA0&W0
*Your 224EH5 is now configured and ready for 9600 bps operation.
*Be sure to set all your dialing directory entries to 9600 bps to
*get the best speed on all calls.
@Multi-Tech MultiModem MT224EH7 (MNP 7)
19200
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,CTS
ATS0=0H0
$Switch Set up on the Bottom of the modem:
$ 4 Bank 1 2 3 4
$ D U D D
$ 8 Bank 1 2 3 4 5 6 7 8
$ U U D U D U U D
$
$Jumpers to be changed -inside- the modem:
$ CTS/RTS: toward the back of the modem.
^AT$A0&B0&BS0&C1$D0&D2$F1
^AT&G0#L0$MI0&M0$R1&R1&S1
^ATB1E1M1Q0V1X4&Q0
^AT&E1&E4&E8&E10&E13&E15
^AT$MB2400$SB19200$BA0&W0
*The 224EH7 is now configured and ready for 19200 bps operation.
*Be sure to set all your dialing directory entries to 19200 bps
*to get the best speed on all calls.
@Multi-Tech MultiModem 696E
19200
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,CTS
ATS0=0H0
$Switch Set up on the Bottom of the modem:
$ 4 Bank 1 2 3 4
$ D U D D
$ 8 Bank 1 2 3 4 5 6 7 8
$ U U D U D U U D
$
$Jumpers to be changed -inside- the modem:
$ CTS/RTS: toward the back of the modem.
^AT$A1&B0&BS0&C1$D0&D2$EP1$F1
^AT&G0&M0$MI0&M0$R1&R1&S1
^ATB1E1M1Q0V1X4&Q0
^AT&E1&E4&E8&E10&E13&E15
^AT$MB9600$SB19200$BA0&W0
*The 696E is now configured and ready for 19200 bps operation.
*Be sure to set all your dialing directory entries to 19200 bps
*to get the best speed on all calls.
@Multi-Tech MultiModem 932EC
19200
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,CTS
ATS0=0H0
^AT&F
^AT&E1&E4&E8&E10&E13&E15
^AT$MB9600$SB19200$BA0&W0
*Your 932EC is now configured and ready for 19200 bps operation.
*Be sure to set all your dialing directory entries to 19200 bps
*to get the best speed on all calls.
@Multi-Tech MultiModem V.32
19200
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,CTS
ATS0=0H0
$Switch Set up on the Bottom of the modem:
$ 4 Bank 1 2 3 4
$ D U D D
$ 8 Bank 1 2 3 4 5 6 7 8
$ U U D U D U U D
$
$Jumpers to be changed -inside- the modem:
$ Open case and move the jumper labeled
$ RTS/CTS so that the jumper it on the CTS side.
^AT&F
^AT&C1&D2B1E1M1Q0V1X4
^AT&E1&E4&E8&E10&E13&E15
^AT$MB9600$SB19200$BA0&W0
*Your V32 is now configured and ready for 19200 bps operation.
*Be sure to set all your dialing directory entries to 19200 bps
*to get the best speed on all calls.
@Multi-Tech MultiModem V32 with V.42bis
38400
ATZ
ATDT
CONNECT
NO DIAL
BUSY
VOICE
DTR,XON
ATS0=0H0
$Switch Set up on the Bottom of the modem:
$ 4 Bank 1 2 3 4
$ D U D D
$ 8 Bank 1 2 3 4 5 6 7 8
$ U U D U D U U D
$
$Jumpers to be changed -inside- the modem:
$ Open case and move the jumper labeled
$ RTS/CTS so that the jumper it on the CTS side.
^AT&F
^AT&C1&D2B1E1M1Q0V1X4
^AT&E1&E4&E8&E10&E13&E15
^AT$MB9600$SB38400$BA0&W0
*Your V32 is now configured and ready for 38400 bps operation.
*Be sure to set all your dialing directory entries to 38400 bps
*to get the best speed on all calls.
@NEC 2431c
9600
ATZ
ATDT
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
CTS
ATS0=0H0
^AT&FV1Q0
^AT&C1&D2&E1S7=55S11=60
^AT&W
*Your NEC 2431c modem is now set up for best perfomance with
*Click Comm. Compression is enabled, so set ALL of your
*dialing directory entries to 9600 bps for best performance.
@NEC N9631 V.32 MNP
19200
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,CTS
ATS0=0H0
^AT&F2
^ATE1Q0&T5\Q3\V1\X1*FT1&W
*Your NEC N9631 modem is configured and ready to go! You can set
*all of your dialing directory entries to 19200 bps and the modem
*will handle speed conversions for you.
@Novation Professional 2400
2400
ATE1Q0V1X3YC0YF1YT0 S7=45 S0=0
ATDT
CONNECT
NO TONE
NO CARRIER
BUSY
VOICE
XON
ATS0=0H0
*Your Novation modem is now configured for best performance
*with Click Comm.
*
*An option might be to add M0 to the modem initial string to
*silence your modem if you prefer.
@OKITEL 2400 Plus
9600
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,CTS
ATS0=0H0
$Switches:
$
$ 1 2 3 4 5 6
$ OFF OFF OFF OFF OFF ON
$
^AT&F
^AT&C1&D2%C0\J0\N3\Q3\V1S25=4&W
*Your OKITEL 2400 Plus is configured and ready to go! You can
*set all of your dialing directory entries to 9600 bps and the
*modem will handle speed conversions for you.
@OkiTel 1200
1200
ATE1Q0V1 S7=55 S11=60 S0=0
ATDT
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
XON
ATS0=0H0
*Your Okidata modem is now configured for best performance
*with Click Comm.
*
*An option might be to add M0 to the modem initial string to
*silence your modem if you prefer.
@OkiTel 2400
2400
ATE1Q0V1X4&C1&D2 S7=55 S11=60 S0=0
ATDT
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
XON
ATS0=0H0
*Your Okidata modem is now configured for best performance
*with Click Comm.
*
*An option might be to add M0 to the modem initial string to
*silence your modem if you prefer.
@OkiTel 9600
19200
ATZ
ATDT
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
CTS
ATS0=0H0
^AT&FV1Q0
^AT&C1&D2
^AT&W
$See ending comments
*Your Okidata modem is now set up for best perfomance with
*Click Comm. Compression is enabled, so set ALL of your
*dialing directory entries to 19200 bps for best performance.
*
*Rear switch 6 should be on, the rest off.
@Penril Alliance V.32
19200
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,CTS
ATS0=0H0
^AT&F
^AT&C1&D2\Q1,1&W
*Your Alliance V.32 modem is configured and ready to go! You can
*set all of your dialing directory entries to 19200 bps and the
*modem will handle speed conversions for you.
@Practical Peripherals PM2400
2400
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,CTS,XON
ATS0=0H0
^ATB1E1L2M1Q0V1X4Y1&C1&D2&G0&J0&L0&P0
^AT&X0&Y0S0=0S2=43&W
*Your PM2400 is now configured and ready to go. Be sure to read
*your modem and double-check the setup.
@Practical PM 1200
1200
ATE1Q0V1 S7=55 S11=60 S0=0
ATDT
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
ATS0=0H0
*Your Practical modem is now configured for best performance
*with Click Comm.
*
*An option might be to add M0 to the modem initial string to
*silence your modem if you prefer.
@Practical 2400SA w/o MNP
2400
ATZ0 ATS7=55 S11=60
ATDT
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
CTS
ATS0=0H0
^ATV1Q0E1X4
^AT&C1&D2
^AT&W
*Your Practical modem is now set up for best perfomance with
*Click Comm.
@Practical Peripherals PM2400SA MNP
9600
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,CTS
ATS0=0H0
^ATB1E1L2M1Q0V1X4Y0&C1&D2&J0&P0
^AT\A3\C1\E0\G0\J0\K5\N3\Q3\V1\X0
^AT%C0%A0S0=0S2=43&W0
*Your PM2400SA MNP is now configured and ready to go.
@Practical Peripherals PM9600SA V.32
38400
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,CTS
ATS0=0H0
^AT&F
^ATW2&C1&D2
*Your PM9600SA V.32 is now configured and ready to go.
@Prometheus Pro 1200
1200
ATE1Q0V1 S7=55 S11=60 S0=0
ATDT
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
XON
ATS0=0H0
*Your Prometheus modem is now configured for best performance
*with Click Comm.
*
*An option might be to add M0 to the modem initial string to
*silence your modem if you prefer.
@Prometheus MCT-24I Half Card
2400
ATE1Q0V1X4&C1&D2 S7=55 S11=60 S0=0
ATDT
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
XON
ATS0=0H0
*Your Prometheus modem is now configured for best performance
*with Click Comm.
*
*An option might be to add M0 to the modem initial string to
*silence your modem if you prefer.
@Prometheus 9600
19200
AT&F^M~~~AT*F3
ATDT
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
CTS
ATS0=0H0
*Your Prometheus modem is now set up for best perfomance with
*Click Comm. Compression is enabled, so set ALL of your
*dialing directory entries to 19200 bps for best performance.
@Quicktel Series 9600 V.32/V.42
19200
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,CTS
ATS0=0H0
^AT&F
^AT&C1&D2\Q3
$ At the bottom of the modem, locate the 8-Position
$ DIP Switch. Verify that switches #7 and #8 are set OFF.
$
$ Open the modem and find the 4-Position DIP Switch.
$ Switches #1, #2 and #3 should be set OFF. Switch #4 should
$ be set ON.
*Your 9600 V.32 is now configuredand ready to go. Be sure to
*read your modem and double-check the setup. Also set all
*dialing directory entries to 19200 bps for maximum throughput.
@Racal Vadic Auto Dial VA212
1200
^~^~D^~
ON LINE
FAILED
VOICE
BUSY
NO DIAL
DTR
^^E^~O
^1^~3^~
^1^~2^~
^16^~2^~
^17^~2^~
^19^~9^~
^
*Be sure to read your manual and double-check the setup.
@Racal Milgo RMD 3221
9600
AT&F ATX9&C1&D2*F2 S7=55 S11=60 S0=0
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
CTS
ATS0=0M1H0
*Your Racal-Vadic modem is now set up for best perfomance
*with Click Comm.
*
*Compression is enabled, so set ALL of your dialing directory
*entries to 9600 bps for best performance.
@Racal Vadic 1200 PA
1200
AT&F~~~AT &C1&D2
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
XON
ATS0=0M1H0
*Your Racal-Vadic modem is now set up for best performance
*with Click Comm.
*
*An option might be to add M0 to the modem initial string to
*silence your modem if you prefer.
@Racal Vadic 2400 PS
2400
ATZ0~~~AT S7=55 S11=60
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
XON
ATS0=0M1H0
^AT&FV1Q0
^AT*F2&C1&D2*E0
^AT&W0
*Your Racal-Vadic is now configured for best performance with
*Click Comm.
*
*An option might be to add M0 to the modem initial string to
*silence your modem if you prefer.
@Racal Vadic 2400 LC
2400
ATZ0^M~~~AT S7=55 S11=60^M
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
XON
ATS0=0M1H0
^AT&FV1Q0
^AT &C1&D2 *E0*F2*P1S7=55S11=60
^AT&W0
*Your Racal-Vadic is now configured for best performance with
*Click Comm.
*
*An option might be to add M0 to the modem initial string to
*silence your modem if you prefer.
@Racal Vadic LC2400 PC
2400
ATZ~~~ATS7=55S11=60
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
XON
ATS0=0M1H0
*Your Racal-Vadic is now configured for best performance with
*Click Comm.
*
*An option might be to add M0 to the modem initial string to
*silence your modem if you prefer.
@Racal Vadic 2400 PA Model 2
2400
ATZ~~~AT S7=55 S11=60
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
XON
ATS0=0M1H0
^AT&FV1Q0
^AT &C1&D2 X4 *E0*L1*Q1*F2*P1
^AT&W
*Your Racal-Vadic is now configured for best performance with
*Click Comm.
*
*An option might be to add M0 to the modem initial string to
*silence your modem if you prefer.
@Racal Vadic 2400 VP
9600
ATZ
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
XON
ATS0=0M1H0
^AT&FV1Q0
^AT &C1*C1&D2*E0*F2Y1S7=55*Q1S11=60
^AT&W
*Your Racal-Vadic modem is now set up for best performance
*with Click Comm. Error correction is enabled, so set all
*dialing directory entries to 9600 for best performance.
*
*An option might be to add M0 to the modem initial string to
*silence your modem if you prefer.
@Racal Vadic 9600 PA
9600
ATZ~~~ATS7=55
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
CTS
ATS0=0M1H0
^AT&FV1Q0
^AT&C1*C1&D2*F2Y1*Q1
^AT&W
*Your Racal-Vadic modem is now set up for best performance
*with Click Comm. Error correction is enabled, so set all
*dialing directory entries to 9600 for best performance.
*
*An option might be to add M0 to the modem initial string to
*silence your modem if you prefer.
@Supra Modem 2400
2400
ATE1Q0V1X4 &C1&D2 S7=55 S11=60 S0=0
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
XON
ATS0=0M1H0
*Your Supra modem is now configured for best performance
*with Click Comm.
*
*An option might be to add M0 to the modem initial string to
*silence your modem if you prefer.
@Sysdyne MDM 24H
2400
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,CTS,XON
ATS0=0M1H0
$The switch settings should remain at factory defaults. If you
$need to select a different COM port other than 2, refer to your
$manual for detailed instructions.
^ATB1E1F1L2M1Q0V1X4Y0
^AT&C1&D2S7=60S11=60&Y0&W0
*Your MDM 24H modem is configured and ready to go! Be sure to
*read your manual and double-check the setup.
@Telebit T1500
9600
ATZ
ATDT
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
CTS
ATH0^~ATS0=0
^AT&FV1Q0
^ATS51=4S0=0S52=1S131=1
^ATS58=2S66=1S68=2&W
*Your Telebit modem is now set up for best perfomance with
*Click Comm. Compression is enabled, so set ALL of your
*dialing directory entries to 9600 bps for best performance.
@Telebit T2000 & Trailblazer Plus
19200
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,CTS
ATH0^~ATS0=0
^AT E1 Q0 M1 V1 W1 X14 Y0 S0=0
^AT S50=0 S51=254 S52=4 S54=3 S58=2
^AT S63=1 S64=0 S66=1 S67=0 S68=2 S90=0
^AT S92=1 S94=1 S95=2 S96=1 S110=1
^AT S111=0 S131=1 S255=0 &W1 &W2
$We are assuming your Telebit is in ECM (Enhanced Command Mode).
$To place your Telebit modem into ECM, follow these steps:
$
$ 1. Start with the modem off and the A/B switch in the
$ A position.
$ 2. Press and hold down the T/D switch while turning on the
$ modem.
$ Release the T/D switch -AFTER- the MR indicator comes on.
$
$This will save the ECM default settings in Profile A of non-
$volatile memory.
$
$ !!!! Do these steps before proceeding! !!!!
$
*Your Telebit is configured and ready to go. To get the most out
*of the dialing directory, be sure to set all phone book entries
*to 19200 bps.
@Telebit T2500
19200
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,CTS
ATS0=0H0
^ATE1Q0M1X4V1S11=60
^AT&C1&D2&G0&J0&K3&L0&P0
^AT&Q5&W
$We are assuming your Telebit is in Conventional Command Mode.
$ (C C M)
$To place your modem into (CCM), follow these steps:
$
$ 1. Switch the modem off.
$ 2. Hold in the T/D switch and Switch the power on. Release
$ the T/D switch when the PEP,CD and MR lights are flashing.
$ Ignore of the other lights that may be lit from here on.
$ 3. Tap the T/D switch until only the CD light is lit (not
$ flashing). The PEP and MR lights should be OFF.
$ 4. Press and hold the T/D switch (2 seconds or more) until the
$ CD light is flashing once again.
$
$ !!!! Do these steps before proceeding! !!!!
*Your Telebit is configured and ready to go. To get the most out
*of the dialing directory, be sure to set all phone book entries
*to 19200 baud.
@TwinCom 96/42i
38400
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR ,XON
ATS0=0H0
^AT&F
^AT&C1&D2\A3&W
*Your Twincom is configured and ready to go! You can set all of
*your dialing directory entries to 38400 bps and the modem will
*handle speed conversions for you.
@UDS Fast Talk 2400
2400
ATE1Q0V1X4&C1&D2 S7=55 S0=0
ATDT
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
XON
ATS0=0H0
*Your UDS modem is now configured for best performance with
*Click Comm.
*
*An option might be to add M0 to the modem initial string to
*silence your modem if you prefer.
@UDS 2440
9600
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON
ATS0=0H0
^AT&F
^ATS7=60
^AT&C1&D2&R&T5%N8%U3%V0%K1&W
$There two jumpers, inside, need to be verified. The RTS
$and CTS flow control. ___
$The pins will be marked like this: o o| o o o
$ o o| FLO CTS
$ F R
$ L T
$ O S
$
$Verify that the pins above RTS are jumpered, and that the right
$two by the CTS are covered. Put the case back together and
*carry on. Your UDS modem is configured and ready to go! To get
*the most out of it, be sure to set all your dialing directory
*entries to 9600 bps.
@UDS V.3224/V.3225 (V.32)
19200
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,CTS
ATS0=0H0
^AT&F
^ATS7=60
^AT&C1&D2&R&T5%C1\Q3\V1&W
*Your UDS modem is configured and ready to go! To get the most
*out of it, be sure to set all your dialing directory entries to 19200 bps.
@USRobotics Direct 1200PC Internal
1200
ATE1Q0M1X1V1S7=60
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^~^~^~+++^~^~^~
^~^~^~+++^~^~^~ATS0=0
$External Switches:
$
$ 1 2 3 4
$ OFF OFF OFF OFF
$
$Jumper Setttings:
$
$ J1 UP
$ J2 UP
$ J3 DOWN
$ J14 UP
$
*Your Direct 1200PC is now configured and ready to go.
@USRobotics Password 1200 Internal
1200
ATE1Q0M1X1V1S7=60
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^~^~^~+++^~^~^~
^~^~^~+++^~^~^~ATS0=0
$External Switches:
$
$ 1 2 3 4
$ UP UP UP UP
$
$Jumper Settings:
$
$ J1 UP
$ J2 UP
$ J3 RIGHT
$ J5 DOWN
$
*Your Password is now configured and ready to go.
@USR Sportster 1200
1200
ATE1Q0V1X2 S7=55 S11=60 S0=0
ATDT
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
^~^~^~+++^~^~^~ATS0=0
$Switch Settings: 1 2 3 4 5 6 7 8
$ U U D U D U U D
*Your USR modem is now configured for best performance with
*Click Comm.
*
*An option might be to add M0 to the modem initial string to
*silence your modem if you prefer.
@USRobotics Direct 2400PC / Sportster 2400
2400
ATE1Q0M1X6V1S7=60S11=60
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,COURIER
ATS0=0H0
$External Switches:
$
$ 1 2 3 4 5 6 7 8 9 10
$ OFF OFF ON OFF ON OFF OFF ON ON ON
$
*Your Courier is now configured and ready to go.
@USRobotics MicroLink 2400
2400
ATE1Q0M1X6V1S7=60S11=60
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,COURIER
ATS0=0H0
$External Switches:
$
$ 1 2 3 4 5 6 7 8 9 10
$ OFF OFF ON OFF ON OFF OFF ON ON ON
$
*Your Courier is now configured and ready to go.
@USRobotics VARmodem 2400
2400
ATE1Q0M1X6V1S7=60S11=60
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON
ATS0=0H0
$External Switches:
$
$ 1 2 3 4 5 6 7 8 9 10
$ OFF OFF ON OFF ON OFF OFF ON ON ON
$
*Your VARmodem is now configured and ready to go.
@USRobotics Courier 2400e and 2400PC w/MNP
2400
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,CTS,COURIER
ATS0=0H0
$External Switches: 1 2 3 4 5 6 7 8 9 10
$ U U D U D U U D D U
$
$ U is UP and D is DOWN
$
$Note: for the 2400PC, turn the modem on it's side so
$ you can read the numbers, this way the above settings
$ will make sense.
%AT&FE0
^ATE1Q0M1X6V1S7=60S11=60
^AT&B0&H1&R2&I0&M4&N0&W
*Your Courier is now configured and ready to go. Consult your
*manual for additional setup parameters if you wish to take
*advantage of speeds higher than 2400 bps when using MNP.
@USR Courier v.32bis
38400
ATZ
ATDT
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
CTS,COURIER
ATS0=0H0
^AT&F
^ATX6&H1&R2&B1
^AT S7=55S0=0 &W
$Switch Settings: 1 2 3 4 5 6 7 8 9 10
$ U U D U D U U D D U
*Your USR modem is now set up for best perfomance with
*Click Comm. Compression is enabled, so set ALL of your
*dialing directory entries to 38400 bps for best performance.
@USRobotics HST (96x ROM)
19200
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,CTS,COURIER
ATS0=0H0
$External switches: 1-UP 2-UP 3-DOWN 4-UP 5-DOWN
$ 6-UP 7-UP 8-DOWN 9-DOWN 10-UP
$ WIDE SWITCH-UP
^ATE1Q0M1V1X7S7=60
^AT&B1&H1&M4&N0&R2&W
*Your Courier HST is now configured and ready to go. To get the
*most out of it, be sure to set all your dialing directory
*entries to 19200 bps.
@USRobotics HST (144x ROM)
19200
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,CTS,COURIER
ATS0=0H0
$External switches: 1-UP 2-UP 3-DOWN 4-UP 5-DOWN
$ 6-UP 7-UP 8-DOWN 9-DOWN 10-UP
$ WIDE SWITCH-UP
^ATE1Q0M1X7V1S7=60
^AT&B1&C1&D2&H1&M4&N0&R2&W
*Your Courier HST is now configured and ready to go. To get the
*most out of it, be sure to set all your dialing directory
*entries to 19200 bps.
@USRobotics HST Dual Standard
38400
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,CTS,COURIER
ATS0=0H0
$External switches: 1-UP 2-UP 3-DOWN 4-UP 5-DOWN
$ 6-UP 7-UP 8-DOWN 9-DOWN 10-UP
$ WIDE SWITCH-UP
^AT&F
^ATB1E1Q0M1X7V1S7=60
^AT&A2&B1&C1&D2&H1&R2&M4&N0&K0&W
*Your Courier HST Dual Standard is now setup so that either
*V.32 or HST calls will be answered. To get the most out of it,
*be sure to set all your dialing directory entries to 38400 bps.
@USRobotics HST (144x ROM) (V.42)
38400
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,CTS,COURIER
ATS0=0H0
$External switches: 1-UP 2-UP 3-DOWN 4-UP 5-DOWN
$ 6-UP 7-UP 8-DOWN 9-DOWN 10-UP
$ WIDE SWITCH-UP
^ATE1Q0M1X7V1S7=60
^AT&A3&K3&B1&C1&D2&H1&M4&N0&R2&W
*Your Courier HST is now configured and ready to go. To get the
*most out of it, be sure to set all your dialing directory
*entries to 38400 bps.
@USRobotics HST Dual Standard (V.42)
38400
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,COURIER
ATS0=0H0
$External switchblock: 1-UP 2-UP 3-DOWN 4-UP 5-DOWN
$ 6-UP 7-UP 8-DOWN 9-DOWN 10-UP
$ WIDE SWITCH-UP
^AT&F
^ATB1E1Q0M1X7V1S7=60
^AT&A3&B1&C1&D2&H1&R2&M4&N0&K3&W
*Your Courier HST Dual Standard is now setup so that either
*V.32 or HST calls will be answered. To get the most out of it,
*be sure to set all your dialing directory entries to 38400 bps.
@USRobotics HST with V.32bis - Duals too
38400
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,COURIER
ATS0=0H0
$External switches: 1-UP 2-UP 3-DOWN 4-UP 5-DOWN
$ 6-UP 7-UP 8-DOWN 9-DOWN 10-UP
$ WIDE SWITCH-UP
^AT&F
^ATE1Q0M1X7V1S7=60
^AT&A3&K3&B1&C1&D2&H1&M4&N0&R2&W
*Your Courier HST is now configured and ready to go. To get the
*most out of it, be sure to set all your dialing directory
*entries to 38400 bps.
@Ven-Tel 2400 Half Card - 4 Option Switches
2400
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,CTS,XON
ATS0=0H0
$Internal switches:
$
$ Refer to your manual for setting the COM port via
$ the above switches. This is setup with switches 3 and 4.
^ATE1M1Q0X4V1&C1&D2&Y0S0=0&W
*Your Vel-Tel 2400 Half Card is now configured and ready to go.
@Ven-Tel 2400 Half Card - 6 Option Switches
2400
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
XON
^~^~^~+++^~^~^~ATH0
ATS0=0H0
$Internal switches:
$
$ 1 2 3 4 5 6
$ O C * * O *
$
$ O = OPEN, C = CLOSED
$ * = Dependes on hardware. See your manual.
$
^ATE1M1Q0X4V1S0=0
*Your Vel-Tel 2400 Half Card is now configured and ready to go.
@Ven-Tel 2400-33
9600
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON
ATS0=0H0
$External switches:
$ 1-OFF 2-OFF 3-OFF 4-OFF 5-OFF
$ 6-OFF 7-ON 8-ON 9-ON 10-OFF
^AT%A13B1\C1&C1\D3&D2E1F1\G0&G0
^AT&L0M1&M0\N3Q0\Q3&R1\T0&T4V1
^AT\V1X4\X1Y0&W
*Your Vel-Tel 2400-33 is now configured and ready. To get the
*most out of it, be sure to set all your dialing directory
*entries to 9600 bps.
@Ven-Tel Pathfinder 18K
19200
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON,CTS
ATS0=0H0
^AT&F
^AT X3 S0=0
^AT S51=5 S54=3 S58=2
^AT S66=1 S68=2 S92=1 S95=2
^AT S111=0 &W
*Your Pathfinder is configured and ready to go. To get the most
*out of the dialing directory, be sure to set all phone book
*entries to 19200 bps.
@ViVa 24m 2400 bps MNP-5
9600
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,XON
ATS0=0H0
^AT&F
^AT&C1&D2%C0\J0\N3\Q3\V1S25=4&W
*Your ViVa 24m is configured and ready to go! You can set all
*of your dialing directory entries to 9600 bps and the modem will
*handle speed conversions for you.
@Zoom/Modem HC2400R
2400
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,CTS
ATS0=0H0
^AT&F
^ATS11=60&C1&D2&W
*Your Zoom HC2400R is configured and ready to go!
@Zoom/Modem MX2400R
2400
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,CTS
ATS0=0H0
^AT&F
^ATS11=60&C1&D2&W
*Your Zoom MX2400R is configured and ready to go!
@Zoom/Modem HC2400S (SendFax)
2400
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,CTS
ATS0=0H0
^AT&F
^ATS11=60&C1&D2&W
*Your Zoom HC2400S is configured and ready to go!
@Zoom/Modem MX2400S (SendFax)
2400
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
DTR,CTS
ATS0=0H0
^AT&F
^ATS11=60&C1&D2&W
*Your Zoom MX2400S is configured and ready to go!
@Zoom MX 2400 (no MNP)
2400
ATZ~~ATV1Q0X4S7=55S11=60S0=0&C1&D2
ATZ
ATDT
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
XON
ATS0=0H0
*Your Zoom modem is now configured for best performance with
*Click Comm.
*
*An option might be to add M0 to the modem initial string to
*silence your modem if you prefer.
@Zoom/Modem V.42bis (2400 bps)
9600
ATZ
ATDT
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
CTS
^~^~^~+++^~^~^~ATH0
ATS0=0H0
^AT&F
^AT&C1&D2S36=7S38=0S95=44
^ATS11=60&W
*Your Zoom HC2400R V.42bis is configured and ready to go!