home *** CD-ROM | disk | FTP | other *** search
/ Current Shareware 1994 January / SHAR194.ISO / hamradio / gen21.zip / GEN6.DAT < prev    next >
Text File  |  1993-03-09  |  11KB  |  291 lines

  1. 160D-17.5  B 4-14  When a transmitter's output power is  |increased by 6 dB(4 times), an S-meter|on a receiver will increase one S-unit
  2. When the power output from a transmitter is increased by four
  3. times, how should the S-meter reading on a nearby receiver change?
  4. A. Decrease by approximately one S-unit
  5. B. Increase by approximately one S-unit
  6. C. Increase by approximately four S-units
  7. D. Decrease by approximately four S-units
  8. *
  9. 161D-17.6  C 4-14  When a transmitter's output power is  |increased by 6 dB(4 times), an S-meter|on a receiver will increase one S-unit
  10. By how many times must the power output from a transmitter be
  11. increased to raise the S-meter reading on a nearby receiver
  12. from S-8 to S-9?
  13. A. Approximately 2 times
  14. B. Approximately 3 times
  15. C. Approximately 4 times
  16. D. Approximately 5 times
  17. *
  18. 162E-1.1   C 5-23  Impedance is the opposition to|the flow of AC in a circuit
  19. What is meant by the term impedance?
  20. A. The electric charge stored by a capacitor
  21. B. The opposition to the flow of AC in a circuit containing
  22.    only capacitance
  23. C. The opposition to the flow of AC in a circuit
  24. D. The force of repulsion presented to an electric field by
  25.    another field with the same charge
  26. *
  27. 163E-1.2   C 5-23  Impedance is the opposition to|the flow of AC in a circuit
  28. What is the opposition to the flow of AC in a circuit
  29. containing both resistance and reactance called?
  30. A. Ohm
  31. B. Joule
  32. C. Impedance
  33. D. Watt
  34. *
  35. 164E-3.1   B 5-21  Reactance(inductive and capacitive)|is the opposition to AC caused by  |inductors and capacitors
  36. What is meant by the term reactance?
  37. A. Opposition to DC caused by resistors
  38. B. Opposition to AC caused by inductors and capacitors
  39. C. A property of ideal resistors in AC circuits
  40. D. A large spark produced at switch contacts when an
  41.    inductor is de-energized
  42. *
  43. 165E-3.2   D 5-22  Inductive reactance
  44. What is the opposition to the flow of AC caused by an
  45. inductor called?
  46. A. Resistance
  47. B. Reluctance
  48. C. Admittance
  49. D. Reactance
  50. *
  51. 166E-3.3   D 5-21  Capacitive reactance 
  52. What is the opposition to the flow of AC caused by a
  53. capacitor called?
  54. A. Resistance
  55. B. Reluctance
  56. C. Admittance
  57. D. Reactance
  58. *
  59. 167E-3.4   D 5-22  Frequency increases|reactance increases
  60. How does a coil react to AC?
  61. A. As the frequency of the applied AC increases, the
  62.    reactance decreases
  63. B. As the amplitude of the applied AC increases, the
  64.    reactance also increases
  65. C. As the amplitude of the applied AC increases, the
  66.    reactance decreases
  67. D. As the frequency of the applied AC increases, the
  68.    reactance also increases
  69. *
  70. 168E-3.5   A 5-22  Frequency increases|reactance decreases
  71. How does a capacitor react to AC?
  72. A. As the frequency of the applied AC increases, the
  73.    reactance decreases
  74. B. As the frequency of the applied AC increases, the
  75.    reactance increases
  76. C. As the amplitude of the applied AC increases, the
  77.    reactance also increases
  78. D. As the amplitude of the applied AC increases, the
  79.    reactance decreases
  80. *
  81. 169E-6.1   A 5-24  When the impedance of the load is|matched to the source impedance|and the SWR is minimum, ie. 1:1
  82. When will a power source deliver maximum output?
  83. A. When the impedance of the load is equal to the impedance of
  84.    the source
  85. B. When the SWR has reached a maximum value
  86. C. When the power supply fuse rating equals the primary winding
  87.    current
  88. D. When air wound transformers are used instead of iron core
  89.    transformers
  90. *
  91. 170E-6.2   D 5-24  Impedance matching means to adjust the|load impedance so that it matches the |source & maximum power is transferred 
  92. What is meant by impedance matching?
  93. A. To make the load impedance much greater than the
  94.    source impedance
  95. B. To make the load impedance much less than the source
  96.    impedance
  97. C. To use a balun at the antenna feed point
  98. D. To make the load impedance equal the source impedance
  99. *
  100. 171E-6.3   D 5-24  When the load impedance is matched|to the source, the source delivers|maximum power to the load
  101. What occurs when the impedance of an electrical load is
  102. equal to the internal impedance of the power source?
  103. A. The source delivers minimum power to the load
  104. B. There will be a high SWR condition
  105. C. No current can flow through the circuit
  106. D. The source delivers maximum power to the load
  107. *
  108. 172E-6.4   A 5-24  So that the source delivers|maximum power to the load
  109. Why is impedance matching important in radio work?
  110. A. So the source can deliver maximum power to the load
  111. B. So the load will draw minimum power from the source
  112. C. To ensure that there is less resistance than reactance
  113.    in the circuit
  114. D. To ensure that the resistance and reactance in the
  115.    circuit are equal
  116. *
  117. 173E-7.2   B 5-21  Ohm
  118. What is the unit measurement of reactance?
  119. A. Mho
  120. B. Ohm
  121. C. Ampere
  122. D. Siemens
  123. *
  124. 174E-7.4   A 5-24  Ohm
  125. What is the unit measurement of impedance?
  126. A. Ohm
  127. B. Volt
  128. C. Ampere
  129. D. Watt
  130. *
  131. 175E-10.1  A 5-11  A unit created by Bell |to describe a change in|power levels
  132. What is a bel?
  133. A. The basic unit used to describe a change in power levels
  134. B. The basic unit used to describe a change in inductances
  135. C. The basic unit used to describe a change in capacitances
  136. D. The basic unit used to describe a change in resistances
  137. *
  138. 176E-10.2  A 5-11  A tenth of a bel
  139. What is a decibel?
  140. A. A unit used to describe a change in power levels,
  141.    equal to 0.1 bel
  142. B. A unit used to describe a change in power levels,
  143.    equal to 0.01 bel
  144. C. A unit used to describe a change in power levels,
  145.    equal to 10 bels
  146. D. A unit used to describe a change in power levels,
  147.    equal to 100 bels
  148. *
  149. 177E-10.3  D 5-11  One dB
  150. Under ideal conditions, a barely detectable change in loudness
  151. is approximately how many dB?
  152. A. 12 dB
  153. B. 6 dB
  154. C. 3 dB
  155. D. 1 dB
  156. *
  157. 178E-10.4  B 5-12  This is a good one to remember |Change in dB = 10*LOG(P2/P1)   |Change in dB = 10*LOG(2) = 3 dB
  158. A two-times increase in power results in a change of how
  159. many dB?
  160. A. Multiplying the original power by 2 gives a new power
  161.    that is 1 dB higher
  162. B. Multiplying the original power by 2 gives a new power
  163.    that is 3 dB higher
  164. C. Multiplying the original power by 2 gives a new power
  165.    that is 6 dB higher
  166. D. Multiplying the original power by 2 gives a new power
  167.    that is 12 dB higher
  168. *
  169. 179E-10.5  D 5-13  If 3 dB is 2 times, then|6 dB is 2 times 2 times |ie. 4 times
  170. An increase of 6 dB results from raising the power by how
  171. many times?
  172. A. Multiply the original power by 1.5 to get the new power
  173. B. Multiply the original power by 2 to get the new power
  174. C. Multiply the original power by 3 to get the new power
  175. D. Multiply the original power by 4 to get the new power
  176. *
  177. 180E-10.6  B 5-12  DBs are ratios.  If +3 dB is double|then -3 dB is half, ie. divide by 2
  178. A decrease of 3 dB results from lowering the power by how
  179. many times?
  180. A. Divide the original power by 1.5 to get the new power
  181. B. Divide the original power by 2 to get the new power
  182. C. Divide the original power by 3 to get the new power
  183. D. Divide the original power by 4 to get the new power
  184. *
  185. 181E-10.7  C 5-12  Since 10*LOG(150/1500) = -10dB|then S9 + 10 dB -10 dB = S9
  186. A signal strength report is "10 dB over S9."  If the
  187. transmitter power is reduced from 1500 watts to 150
  188. watts, what should be the new signal strength report?
  189. A. S5
  190. B. S7
  191. C. S9
  192. D. S9 plus 5 dB
  193. *
  194. 182E-10.8  D 5-12  Since 10*LOG(150/1500) = -10dB then|S9 + 20 dB -10 dB = S9 + 10 dB
  195. A signal strength report is "20 dB over S9."  If the
  196. transmitter power is reduced from 1500 watts to 150
  197. watts, what should be the new signal strength report?
  198. A. S5
  199. B. S7
  200. C. S9
  201. D. S9 plus 10 dB
  202. *
  203. 183E-10.9  C 5-12  Since 10*LOG(15/1500) = -20dB then|S9 + 20 dB -20 dB = S9
  204. A signal strength report is "20 dB over S9."  If the
  205. transmitter power is reduced from 1500 watts to 15
  206. watts, what should be the new signal strength report?
  207. A. S5
  208. B. S7
  209. C. S9
  210. D. S9 plus 10 dB
  211. *
  212. 184E-12.1  D 5-6   Current splits evenly|into two .5 amps
  213. If a 1.0-ampere current source is connected to two parallel-
  214. connected 10 ohm resistors, how much current passes through
  215. each resistor?
  216. A. 10 amperes
  217. B. 2 amperes
  218. C. 1 ampere
  219. D. 0.5 ampere
  220. *
  221. 185E-12.3  B 5-8   The total current equals the|sum of the branch currents, |ie.  It = I1 + I2 + I3...   
  222. In a parallel circuit with a voltage source and several branch
  223. resistors, what relationship does the total current have to the
  224. current in the branch circuits?
  225. A. The total current equals the average of the branch current
  226.    through each resistor
  227. B. The total current equals the sum of the branch current through
  228.    each resistor
  229. C The total current decreases as more parallel resistors are
  230.    added to the circuit
  231. D. The total current is calculated by adding the voltage drops
  232.    across each resistor and multiplying the sum by the total
  233.    number of all circuit resistors
  234. *
  235. 186E-13.1  B 5-8   P = E*E/R, P = 400*400/800|P = 160000/800,    P = 200
  236. How many watts of electrical power are being used when a
  237. 400-VDC power source supplies an 800 ohm load?
  238. A. 0.5 watt
  239. B. 200 watts
  240. C. 400 watts
  241. D. 320,000 watts
  242. *
  243. 187E-13.2  D 5-10  P = I*E, P = .2*12, P = 2.4 watts
  244. How many watts of electrical power are being consumed by a
  245. 12-VDC pilot light which draws 0.2-amperes?
  246. A. 60 watts
  247. B. 24 watts
  248. C. 6 watts
  249. D. 2.4 watts
  250. *
  251. 188E-13.3  A 5-10  P = I*I*R,  P = .007*.007*1250   |P = .061 watts, ie. 61 milliwatts
  252. How many watts are being dissipated when 7.0-milliamperes
  253. flows through 1.25 kilohms?
  254. A. Approximately 61 milliwatts
  255. B. Approximately 39 milliwatts
  256. C. Approximately 11 milliwatts
  257. D. Approximately 9 milliwatts
  258. *
  259. 189E-14.1  C 5-5   The total resistance is the sum|of individual resistances,  ie.|Rt = R1 + R2 + R3...
  260. How is the total resistance calculated for several resistors
  261. in series?
  262. A. The total resistance must be divided by the number of
  263.    resistors to ensure accurate measurement of resistance
  264. B. The total resistance is always the lowest-rated resistance
  265. C. The total resistance is found by adding the individual
  266.    resistances together
  267. D. The tolerance of each resistor must be raised proportionally
  268.    to the number of resistors
  269. *
  270. 190E-14.2  D 5-6   In general, the total resistance is|the product divided by the sum.  If|R1 = R2 then Rt = R1*R1/2*R1 = R1/2
  271. What is the total resistance of two equal, parallel-connected
  272. resistors?
  273. A. Twice the resistance of either resistance
  274. B. The sum of the two resistances
  275. C. The total resistance cannot be determined without
  276.    knowing the exact resistances
  277. D. Half the resistance of either resistor
  278. *
  279. 191E-14.3  A 5-18  If no mutual coupling, inductances in|parallel add the same as resistors in|parallel, ie total inductance is L1/2
  280. What is the total inductance of two equal, parallel-connected
  281. inductors?
  282. A. Half the inductance of either inductor, assuming no mutual 
  283.    coupling
  284. B. Twice the inductance of either inductor, assuming no mutual
  285.    coupling
  286. C. The sum of the two inductances, assuming no mutual coupling
  287. D. The total inductance cannot be determined without knowing
  288.    the exact inductances
  289. *
  290. 
  291.