106 Insert the manufacturer's installation disk into the drive selected, and then click OK.
107 Insert %1 into the drive selected below, and then click OK.
108 Type the path where the file is located, and then click OK.
109 Insert Disk
110 Copy Error
111 An error has occured copying %1.
112 If you skip this file Windows NT might not work correctly. Are you sure you want to skip this file?
113 If you cancel now Windows NT might not work correctly. Are you sure you want to cancel?
114 Ensure that the manufacturer's disk is properly inserted in the drive selected below, or provide the location where the file can be found.
115 Ensure that the disk labeled '%1' is in the drive selected below, or provide the location where the file can be found.
116 Ensure that the location specified below is correct, or change it and insert '%1' in the drive you specify.
117 Warning
120 Error Details
121 Error
122 Rename Error
123 Delete Error
143 From: %1
144 To: %1
145 %1
146 %1 -- Copying Files
147 Copying Files
148 %1 -- Renaming Files
149 Renaming Files
150 %1 -- Deleting Files
151 Deleting Files
155 Installation is not yet completed. Are you sure you want to cancel?
200 %s: The following models are compatible with your hardware. Click the one you want to set up, and then click OK.
201 Click the %s that matches your hardware, and then click OK. If you don't know which model you have, click OK.
205 If your model is not on the list, click Show All Devices.
206 If you have an installation disk for this device, click Have Disk.
212 This list shows only what was found on the installation disk.
309 Install From Disk
430 Click the manufacturer and model of your hardware. If your hardware is not listed, or if you have an installation disk, click Have Disk.\n\n
431 If your hardware is still not listed, click Back, and then select a different hardware type. To see all hardware choices, click Unknown Hardware.
600 ENG
704 Select Device
1000 Resource type
1001 Setting
1002 You cannot modify the resources for this device directly. To change its resources, change the resources of its parent device.
1003 Basic configuration
1005 Memory Range
1006 Input/Output Range
1007 Direct Memory Access
1008 Interrupt Request
1009 interrupt request
1010 direct memory access
1011 memory range
1012 input/output range
1020 Windows NT cannot determine which resources this device is using.
1021 This is probably because you are running in Safe Mode.
1022 This is probably because Windows NT cannot assign a configuration due to a conflict with other devices in the computer.
1023 This device isn't using any resources because it is not currently enabled or has a problem.\n\n
1024 If you want to assign resources manually for this device, click Set Configuration Manually.
1025 The resources this device is using do not match any of its known configurations. To assign resources manually for this device, click Set Configuration Manually.
1026 No Modifications Allowed
1027 Enter the %s you would like to set for this device.\n\n
1028 You may either enter a specific range and the nearest valid range will be automatically selected, or you may select a range using the up and down arrows.
1029 Edit Resource Setting
1030 The setting you entered, %s, is not valid for this device.\n\n
1031 The next valid setting of %s has been chosen automatically.\n\n
1032 Would you like to continue using the new setting?
1033 Either the starting or ending value you entered is invalid.\n\nCheck that the starting and ending values are between 0x00000000 and 0xFFFFFFFF.
1034 Either the starting or ending value you entered is invalid.\n\nCheck that the starting and ending values are between 0x0000 and 0xFFFF.
1035 The direct memory access (DMA) value entered is invalid.\n\nCheck that the DMA value is between 0 and 7.
1036 The interrupt request (IRQ) value entered is invalid.\n\nPlease check that the IRQ value is between 0 and 15.
1037 Warning: The setting you have chosen conflicts with another device.\n\nTo select a different resource setting, click No. To continue, click Yes.
1038 Conflict Warning
1049 No conflict information is currently available.
1050 You cannot modify the resources in this configuration. Try choosing a different configuration in the Settings Based On box.
1051 This resource setting cannot be modified.
1052 Enter the %s you would like to set for this device.\n\n
1053 You may either enter a specific value and the nearest valid value will be automatically selected, or you may select a value using the up and down arrows.
1054 Edit %s
1055 Windows NT cannot determine if the setting you have chosen conflicts with another device.
1056 Unknown
1057 The setting you have chosen does not conflict with any other devices.
1058 No devices are conflicting.
1059 Windows NT will choose settings for this device.\n\nTo modify a setting, clear the Use Automatic Settings check box by clicking it, and then make your changes.
1060 Creating a Forced Configuration
1061 You adjusted one or more resource settings manually.\n\n
1062 If you continue, these settings will be assigned to the device.\n\n
1063 Do you want to continue?
1065 Warning: The setting you have chosen conflicts with another device.
