3218 Send is not yet complete. Unexpected disconnect.
3219 >>> Data Available timer has expired
3220 >>> Clear To Send timer has expired
3221 >>> Connection Established timer has expired
3222 >>> Disconnect Complete timer has expired
3223 Unexpected timer message
3224 InitializeChannel: G3 Fax
3225 Unable to initialize channel. %s
3226 Unable to configure channel. %s.
3227 SendAJob: dialing for G3 fax connection
3228 Error while dialing: %s
3229 Error - event already in progress
3230 OnClearToSend %d
3231 All data has been sent. Message ignored.
3232 Send failed
3233 Not in send mode. Message ignored.
3234 OnDataReceived %d
3235 Job is complete or cancelled. Message ignored.
3236 Receive failed. Aborting call.
3237 OnReceiveQFull *********
3238 OnConnectionEstablished
3239 Sending first blocks of data
3240 Ready to receive data
3241 OnDisconnecting
3242 OnNoConnection
3243 Unexpected disconnect BUT send is complete!
3244 Unexpected disconnect.
3245 Unexpected job status.
3246 No more retries. Mark job as failed.
3247 Receive job initiated but connection never established.
3248 Receive failed. Error code %d.
3249 OnJobAborted
3250 InitializeChannel: X75 (SpeedFax)
3251 SendAJob: dialing for BFT (X75) connection
3252 Waiting for SpeedFax handshake response. Message ignored.
3253 SpeedFax handshake successfully completed
3254 SpeedFax handshake failed. Aborting call.
3255 Looking for response to SpeedFax handshake
3256 Correct SpeedFax response detected
3257 Wrong response. Closing connection.
3258 Unexpected data received. Message ignored.
3259 OnConnectRequest
3260 Call rejected: Speed fax disabled.
3261 Sending initial handshake packet
3262 Couldn't allocate timer for response timeout
3263 Couldn't send handshake packet.
3264 Ready to receive data. Waiting for handshake.
3265 Retry this job as a fax call
3266 Send failed. Error code %d.
3267 No response to SpeedFax handshake within timeout period
3268 Call ignored: Global calls (no MSN) are disabled
3269 Call accepted. (Global call - no MSN)
3270 Error: CAPI does not support G3 Fax protocol
3271 Error: CAPI does not support X75 protocol
5000 ISDN
5001 ISDN/CAPI
5002 ISDN/CAPI (Common ISDN API)
5003 Unknown
5004 Caller
5005 ISDN Error:
5006 Invalid channel ID
5007 The remote is busy
5008 The remote has rejected the call
5009 No answer
5010 No line to the exchange (check cable)
5011 Requested service is unavailable or has not been applied for
5012 Connection is barred against outgoing calls
5013 Connection cannot be made because of a negative Closed User Group
5014 Wrong destination
5015 Remote number had changed
5016 Remote is barred against incoming calls or has not applied for the requested service
5017 Remote is out of order
5018 Group 3 fax error
5019 CAPI unlisted error
5020 CAPI is unstable
5021 CAPI not found
5022 ISDN channel not initialized
5023 Channel not active
5024 Current channel state not valid for requested function
5025 Connection not present
5026 Send queue is full. Data cannot be sent
5027 No more channels are available
5028 Transmission refused, block passed is too large
5029 Queue hook has already been installed
5030 Not enough memory available
5031 The number to call is invalid
5032 Invalid function parameter
5033 There is no incoming call
5034 Requested timer resource is not available
5035 No error code is available
5036 Your ISDN card/CAPI drivers are not configured properly to work with WinFax. Please exit WinFax and re-configure your ISDN card before trying to use WinFax again.
5037 WinFax
5038 WinFax is unable to send your fax because your packet size setting is too large. Reduce the packet size (on the Setup menu, click Modem, click your ISDN card and then click Properties) and try re-sending your fax.
5039 ISDN Device (CAPI 2.0)
5040 The CAPI installed on your system does not support the G3 Fax protocol. You will not be able to fax with this version of CAPI. Contact your ISDN card manufacturer for a CAPI update with fax support.
6000 CAPI Version Checker Warning
6001 A CAPI driver has been detected but it reports that it is not properly installed. Contact your ISDN card manufacturer for a CAPI update and try reinstalling the driver.
6002 Your version of CAPI has not been verified by Symantec to fax reliably. Contact your ISDN card manufacturer for a CAPI driver update and install the driver before attempting to use ISDN for faxing.
6003 Your CAPI driver has not been verified by Symantec as being able to fax reliably. If you proceed, there is no guarantee that you will be able to successfully send or receive faxes.
6004 Cannot run the CAPI checker to validate that CAPI is properly installed on your system.
6005 Unable to find a CAPI driver on your system. You cannot fax using ISDN without a properly installed ISDN card and CAPI driver. Contact your ISDN card manufacturer for a CAPI update and try reinstalling your CAPI driver.
6006 Unable to load the CAPI driver found on your system. Please ensure that your CAPI driver is properly installed or you will not be able to fax using ISDN.
6007 The CAPI driver found on your system does not have the standard entry points required for validation. Contact your ISDN card manufacturer for a CAPI 2.0 driver update and try reinstalling the driver.
6008 Testing by Symantec has shown that the CAPI driver installed on your system does NOT work (or is not reliable) under %s. You will likely not be able to fax using ISDN.
6009 Testing by Symantec has shown that the CAPI driver installed on your system does NOT work (or is not reliable) with %s. You will likely not be able to fax using ISDN.
6010 The detected CAPI driver reports that it is not fax capable. You will not be able to fax with this driver. Contact your ISDN card manufacturer for a CAPI update with fax support.